From: Christoph Niedermaier Date: Sun, 28 Nov 2021 02:53:18 +0000 (+0100) Subject: ARM: dts: imx6q-dhcom: Use 1G ethernet on the PDK2 board X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=ca27227c5940371c792cfd36826315b3e17e46a1;p=u-boot.git ARM: dts: imx6q-dhcom: Use 1G ethernet on the PDK2 board The PDK2 board is capable of running both 100M and 1G ethernet. However, the i.MX6 has only one ethernet MAC, so it is possible to configure either 100M or 1G Ethernet. In case of 100M option, the PHY is on the SoM and the signals are routed to a RJ45 port. For 1G the PHY is on the PDK2 board with another RJ45 port. 100M and 1G ethernet use different signal pins from the i.MX6, but share the MDIO bus. This SoM board combination is used to demonstrate how to enable 1G ethernet configuration. Signed-off-by: Christoph Niedermaier Signed-off-by: Marek Vasut Cc: Christoph Niedermaier Cc: Stefano Babic --- diff --git a/arch/arm/dts/imx6qdl-dhcom-pdk2-u-boot.dtsi b/arch/arm/dts/imx6qdl-dhcom-pdk2-u-boot.dtsi index 32128d4d2a..a1ffb1d6fc 100644 --- a/arch/arm/dts/imx6qdl-dhcom-pdk2-u-boot.dtsi +++ b/arch/arm/dts/imx6qdl-dhcom-pdk2-u-boot.dtsi @@ -15,7 +15,7 @@ }; &fec { - phy-reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>; phy-reset-duration = <1>; phy-reset-post-delay = <10>; diff --git a/arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi b/arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi index af4719aaeb..d8772a9896 100644 --- a/arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi +++ b/arch/arm/dts/imx6qdl-dhcom-pdk2.dtsi @@ -38,6 +38,45 @@ status = "okay"; }; +/* 1G ethernet */ +/delete-node/ ðphy0; +&fec { + phy-mode = "rgmii"; + phy-handle = <ðphy7>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet_1G>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy7: ethernet-phy@7 { /* KSZ 9021 */ + compatible = "ethernet-phy-ieee802.3-c22"; + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&pinctrl_ethphy7>; + pinctrl-names = "default"; + reg = <7>; + reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>; + reset-assert-us = <1000>; + reset-deassert-us = <1000>; + rxc-skew-ps = <3000>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txc-skew-ps = <3000>; + txd0-skew-ps = <0>; + txd1-skew-ps = <0>; + txd2-skew-ps = <0>; + txd3-skew-ps = <0>; + rxdv-skew-ps = <0>; + txen-skew-ps = <0>; + }; + }; +}; + &hdmi { ddc-i2c-bus = <&i2c2>; status = "okay"; @@ -113,9 +152,14 @@ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 - MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x000b0 - MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x000b1 - MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x000b1 + >; + }; + + pinctrl_ethphy7: ethphy7-grp { + fsl,pins = < + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0xb0 /* Reset */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0xb1 /* Int */ + MX6QDL_PAD_EIM_D26__GPIO3_IO26 0xb1 /* WOL */ >; }; diff --git a/include/configs/dh_imx6.h b/include/configs/dh_imx6.h index 8b8cd4c31b..410ac89076 100644 --- a/include/configs/dh_imx6.h +++ b/include/configs/dh_imx6.h @@ -32,9 +32,9 @@ /* FEC ethernet */ #define IMX_FEC_BASE ENET_BASE_ADDR -#define CONFIG_FEC_XCV_TYPE RMII +#define CONFIG_FEC_XCV_TYPE RGMII #define CONFIG_ETHPRIME "FEC" -#define CONFIG_FEC_MXC_PHYADDR 0 +#define CONFIG_FEC_MXC_PHYADDR 7 #define CONFIG_ARP_TIMEOUT 200UL /* MMC Configs */