From: Andreas Bießmann Date: Mon, 11 May 2015 11:07:26 +0000 (+0200) Subject: avr32: delete non generic board mimc200 X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=c62d2f8fc5c6;p=u-boot.git avr32: delete non generic board mimc200 Signed-off-by: Andreas Bießmann --- diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig index cfcdbe7565..0c7b1ba11a 100644 --- a/arch/avr32/Kconfig +++ b/arch/avr32/Kconfig @@ -29,15 +29,11 @@ config TARGET_ATSTK1006 config TARGET_GRASSHOPPER bool "Support grasshopper" -config TARGET_MIMC200 - bool "Support mimc200" - endchoice source "board/atmel/atngw100/Kconfig" source "board/atmel/atngw100mkii/Kconfig" source "board/atmel/atstk1000/Kconfig" source "board/in-circuit/grasshopper/Kconfig" -source "board/mimc/mimc200/Kconfig" endmenu diff --git a/board/mimc/mimc200/Kconfig b/board/mimc/mimc200/Kconfig deleted file mode 100644 index 18736d7f96..0000000000 --- a/board/mimc/mimc200/Kconfig +++ /dev/null @@ -1,15 +0,0 @@ -if TARGET_MIMC200 - -config SYS_BOARD - default "mimc200" - -config SYS_VENDOR - default "mimc" - -config SYS_SOC - default "at32ap700x" - -config SYS_CONFIG_NAME - default "mimc200" - -endif diff --git a/board/mimc/mimc200/MAINTAINERS b/board/mimc/mimc200/MAINTAINERS deleted file mode 100644 index 6cb51dd3cb..0000000000 --- a/board/mimc/mimc200/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -MIMC200 BOARD -M: Mark Jackson -S: Maintained -F: board/mimc/mimc200/ -F: include/configs/mimc200.h -F: configs/mimc200_defconfig diff --git a/board/mimc/mimc200/Makefile b/board/mimc/mimc200/Makefile deleted file mode 100644 index 5c30c0dbca..0000000000 --- a/board/mimc/mimc200/Makefile +++ /dev/null @@ -1,6 +0,0 @@ -# -# Copyright (C) 2005-2006 Atmel Corporation -# -# SPDX-License-Identifier: GPL-2.0+ - -obj-y := mimc200.o diff --git a/board/mimc/mimc200/mimc200.c b/board/mimc/mimc200/mimc200.c deleted file mode 100644 index f078295508..0000000000 --- a/board/mimc/mimc200/mimc200.c +++ /dev/null @@ -1,197 +0,0 @@ -/* - * Copyright (C) 2006 Atmel Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include -#include - -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include "../../../arch/avr32/cpu/hsmc3.h" - -struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = { - { - .virt_pgno = CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT, - .nr_pages = CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT, - .phys = (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT) - | MMU_VMR_CACHE_NONE, - }, { - .virt_pgno = EBI_SRAM_CS2_BASE >> MMU_PAGE_SHIFT, - .nr_pages = EBI_SRAM_CS2_SIZE >> MMU_PAGE_SHIFT, - .phys = (EBI_SRAM_CS2_BASE >> MMU_PAGE_SHIFT) - | MMU_VMR_CACHE_NONE, - }, { - .virt_pgno = CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT, - .nr_pages = EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT, - .phys = (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT) - | MMU_VMR_CACHE_WRBACK, - }, -}; - -#if defined(CONFIG_LCD) -/* 480x272x16 @ 72 Hz */ -vidinfo_t panel_info = { - .vl_col = 480, /* Number of columns */ - .vl_row = 272, /* Number of rows */ - .vl_clk = 5000000, /* pixel clock in ps */ - .vl_sync = ATMEL_LCDC_INVCLK_INVERTED | - ATMEL_LCDC_INVLINE_INVERTED | - ATMEL_LCDC_INVFRAME_INVERTED, - .vl_bpix = LCD_COLOR16, /* Bits per pixel, BPP = 2^n */ - .vl_tft = 1, /* 0 = passive, 1 = TFT */ - .vl_hsync_len = 42, /* Length of horizontal sync */ - .vl_left_margin = 1, /* Time from sync to picture */ - .vl_right_margin = 1, /* Time from picture to sync */ - .vl_vsync_len = 1, /* Length of vertical sync */ - .vl_upper_margin = 12, /* Time from sync to picture */ - .vl_lower_margin = 1, /* Time from picture to sync */ - .mmio = LCDC_BASE, /* Memory mapped registers */ -}; - -void lcd_enable(void) -{ -} - -void lcd_disable(void) -{ -} -#endif - -DECLARE_GLOBAL_DATA_PTR; - -static const struct sdram_config sdram_config = { - .data_bits = SDRAM_DATA_16BIT, - .row_bits = 13, - .col_bits = 9, - .bank_bits = 2, - .cas = 3, - .twr = 2, - .trc = 6, - .trp = 2, - .trcd = 2, - .tras = 6, - .txsr = 6, - /* 15.6 us */ - .refresh_period = (156 * (SDRAMC_BUS_HZ / 1000)) / 10000, -}; - -int board_early_init_f(void) -{ - /* Enable SDRAM in the EBI mux */ - hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE)); - - /* Enable 26 address bits and NCS2 */ - portmux_enable_ebi(16, 26, PORTMUX_EBI_CS(2), PORTMUX_DRIVE_HIGH); - sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config); - - portmux_enable_usart1(PORTMUX_DRIVE_MIN); - - /* de-assert "force sys reset" pin */ - portmux_select_gpio(PORTMUX_PORT_D, 1 << 15, - PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH); - - /* init custom i/o */ - /* cpu type inputs */ - portmux_select_gpio(PORTMUX_PORT_E, (1 << 19) | (1 << 20) | (1 << 23), - PORTMUX_DIR_INPUT); - /* main board type inputs */ - portmux_select_gpio(PORTMUX_PORT_B, (1 << 19) | (1 << 29), - PORTMUX_DIR_INPUT); - /* DEBUG input (use weak pullup) */ - portmux_select_gpio(PORTMUX_PORT_E, 1 << 21, - PORTMUX_DIR_INPUT | PORTMUX_PULL_UP); - - /* are we suppressing the console ? */ - if (gpio_get_value(GPIO_PIN_PE(21)) == 1) - gd->flags |= (GD_FLG_SILENT | GD_FLG_DISABLE_CONSOLE); - - /* reset phys */ - portmux_select_gpio(PORTMUX_PORT_E, 1 << 24, PORTMUX_DIR_INPUT); - portmux_select_gpio(PORTMUX_PORT_C, 1 << 18, - PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH); - - udelay(5000); - - /* release phys reset */ - gpio_set_value(GPIO_PIN_PC(18), 0); /* PHY RESET (Release) */ - - /* setup Data Flash chip select (NCS2) */ - hsmc3_writel(MODE2, 0x20121003); - hsmc3_writel(CYCLE2, 0x000a0009); - hsmc3_writel(PULSE2, 0x0a060806); - hsmc3_writel(SETUP2, 0x00030102); - - /* setup FRAM chip select (NCS3) */ - hsmc3_writel(MODE3, 0x10120001); - hsmc3_writel(CYCLE3, 0x001e001d); - hsmc3_writel(PULSE3, 0x08040704); - hsmc3_writel(SETUP3, 0x02050204); - -#if defined(CONFIG_MACB) - /* init macb0 pins */ - portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH); - portmux_enable_macb1(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH); -#endif - -#if defined(CONFIG_MMC) - portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW); -#endif - -#if defined(CONFIG_LCD) - portmux_enable_lcdc(1); -#endif - - return 0; -} - -int board_early_init_r(void) -{ - gd->bd->bi_phy_id[0] = 0x01; - gd->bd->bi_phy_id[1] = 0x03; - return 0; -} - -int board_postclk_init(void) -{ - /* Use GCLK0 as 10MHz output */ - gclk_enable_output(0, PORTMUX_DRIVE_LOW); - gclk_set_rate(0, GCLK_PARENT_OSC0, 10000000); - return 0; -} - -/* SPI chip select control */ -#ifdef CONFIG_ATMEL_SPI -#include - -int spi_cs_is_valid(unsigned int bus, unsigned int cs) -{ - return (bus == 0) && (cs == 0); -} - -void spi_cs_activate(struct spi_slave *slave) -{ -} - -void spi_cs_deactivate(struct spi_slave *slave) -{ -} -#endif /* CONFIG_ATMEL_SPI */ - -#ifdef CONFIG_CMD_NET -int board_eth_init(bd_t *bi) -{ - macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, bi->bi_phy_id[0]); - macb_eth_initialize(1, (void *)ATMEL_BASE_MACB1, bi->bi_phy_id[1]); - - return 0; -} -#endif diff --git a/configs/mimc200_defconfig b/configs/mimc200_defconfig deleted file mode 100644 index 85c646ec16..0000000000 --- a/configs/mimc200_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_AVR32=y -CONFIG_TARGET_MIMC200=y -CONFIG_CMD_NET=y diff --git a/include/configs/mimc200.h b/include/configs/mimc200.h deleted file mode 100644 index e8e5ae73ec..0000000000 --- a/include/configs/mimc200.h +++ /dev/null @@ -1,176 +0,0 @@ -/* - * Copyright (C) 2006 Atmel Corporation - * - * Configuration settings for the AVR32 Network Gateway - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#include - -#define CONFIG_AT32AP -#define CONFIG_AT32AP7000 -#define CONFIG_MIMC200 - -#define CONFIG_MIMC200_EXT_FLASH - -/* - * Set up the PLL to run at 140 MHz, the CPU to run at the PLL - * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency - * and the PBA bus to run at 1/4 the PLL frequency. - */ -#define CONFIG_PLL -#define CONFIG_SYS_POWER_MANAGER -#define CONFIG_SYS_OSC0_HZ 10000000 -#define CONFIG_SYS_PLL0_DIV 1 -#define CONFIG_SYS_PLL0_MUL 15 -#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16 -#define CONFIG_SYS_CLKDIV_CPU 0 -#define CONFIG_SYS_CLKDIV_HSB 1 -#define CONFIG_SYS_CLKDIV_PBA 2 -#define CONFIG_SYS_CLKDIV_PBB 1 - -/* Reserve VM regions for SDRAM, NOR flash and FRAM */ -#define CONFIG_SYS_NR_VM_REGIONS 3 - -/* - * The PLLOPT register controls the PLL like this: - * icp = PLLOPT<2> - * ivco = PLLOPT<1:0> - * - * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). - */ -#define CONFIG_SYS_PLL0_OPT 0x04 - -#define CONFIG_USART_BASE ATMEL_BASE_USART1 -#define CONFIG_USART_ID 1 - -#define CONFIG_MIMC200_DBGLINK 1 - -/* User serviceable stuff */ -#define CONFIG_DOS_PARTITION - -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG - -#define CONFIG_STACKSIZE (2048) - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTARGS \ - "root=/dev/mtdblock1 rootfstype=jffs2 fbmem=512k console=ttyS1" -#define CONFIG_BOOTCOMMAND \ - "fsload boot/uImage; bootm" - -#define CONFIG_SILENT_CONSOLE /* enable silent startup */ -#define CONFIG_DISABLE_CONSOLE /* disable console */ -#define CONFIG_SYS_DEVICE_NULLDEV /* include nulldev device */ - -#define CONFIG_LCD 1 - -/* - * Only interrupt autoboot if is pressed. Otherwise, garbage - * data on the serial line may interrupt the boot sequence. - */ -#define CONFIG_BOOTDELAY 0 -#define CONFIG_ZERO_BOOTDELAY_CHECK -#define CONFIG_AUTOBOOT - -/* - * After booting the board for the first time, new ethernet addresses - * should be generated and assigned to the environment variables - * "ethaddr" and "eth1addr". This is normally done during production. - */ -#define CONFIG_OVERWRITE_ETHADDR_ONCE - -/* - * BOOTP/DHCP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MMC - -#define CONFIG_ATMEL_USART -#define CONFIG_MACB -#define CONFIG_PORTMUX_PIO -#define CONFIG_SYS_NR_PIOS 5 -#define CONFIG_SYS_HSDRAMC -#define CONFIG_MMC -#define CONFIG_GENERIC_ATMEL_MCI -#define CONFIG_GENERIC_MMC - -#if defined(CONFIG_LCD) -#define CONFIG_CMD_BMP -#define CONFIG_ATMEL_LCD 1 -#define LCD_BPP LCD_COLOR16 -#define CONFIG_BMP_16BPP 1 -#define CONFIG_FB_ADDR 0x10600000 -#define CONFIG_WHITE_ON_BLACK 1 -#define CONFIG_VIDEO_BMP_GZIP 1 -#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE 262144 -#define CONFIG_ATMEL_LCD_BGR555 1 -#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 -#define CONFIG_SPLASH_SCREEN 1 -#endif - -#define CONFIG_SYS_DCACHE_LINESZ 32 -#define CONFIG_SYS_ICACHE_LINESZ 32 - -#define CONFIG_NR_DRAM_BANKS 1 - -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER - -#define CONFIG_SYS_FLASH_BASE 0x00000000 -#define CONFIG_SYS_FLASH_SIZE 0x800000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 135 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_TEXT_BASE 0x00000000 - -#define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE -#define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE -#define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE - -#define CONFIG_SYS_FRAM_BASE 0x08000000 -#define CONFIG_SYS_FRAM_SIZE 0x20000 - -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SIZE 65536 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE) - -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE) - -#define CONFIG_SYS_MALLOC_LEN (1024*1024) - -/* Allow 4MB for the kernel run-time image */ -#define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) -#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024) - -/* Other configuration settings that shouldn't have to change all that often */ -#define CONFIG_SYS_PROMPT "U-Boot> " -#define CONFIG_SYS_CBSIZE 256 -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP - -#define CONFIG_SYS_MEMTEST_START EBI_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x1f00000) - -#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } - -#endif /* __CONFIG_H */