From: Yangbo Lu Date: Thu, 3 Jun 2021 02:51:17 +0000 (+0800) Subject: mmc: fsl_esdhc: convert to CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=ae7020b435883f48f944d6682914a511044703ae;p=u-boot.git mmc: fsl_esdhc: convert to CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT For eSDHC, power supply is through peripheral circuit. Some eSDHC versions have value 0 of the bit but that does not reflect the truth. 3.3V is common for SD/MMC, and is supported for all boards with eSDHC in current u-boot. So, make 3.3V is supported in default in code. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if future board does not support 3.3V. This is also a fix-up for one previous patch, which converted to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 that is not a Kconfig option. Fixes: 52faec31827e ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()") Signed-off-by: Yangbo Lu Reviewed-by: Jaehoon Chung Reviewed-by: Priyanka Jain --- diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig index 8901456967..0909f502a1 100644 --- a/drivers/mmc/Kconfig +++ b/drivers/mmc/Kconfig @@ -798,6 +798,13 @@ config FSL_ESDHC_33V_IO_RELIABILITY_WORKAROUND This option assumes no hotplug, and u-boot has to make all the way to to linux to use 1.8v UHS-I speed mode if has card. +config FSL_ESDHC_VS33_NOT_SUPPORT + bool "3.3V power supply not supported" + depends on FSL_ESDHC + help + For eSDHC, power supply is through peripheral circuit. 3.3V support is + common. Select this if 3.3V power supply not supported. + config FSL_ESDHC_IMX bool "Freescale/NXP i.MX eSDHC controller support" help diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c index 7501fdb71e..1d98fa65c4 100644 --- a/drivers/mmc/fsl_esdhc.c +++ b/drivers/mmc/fsl_esdhc.c @@ -1,7 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc - * Copyright 2019-2020 NXP + * Copyright 2019-2021 NXP * Andy Fleming * * Based vaguely on the pxa mmc code: @@ -795,10 +795,21 @@ static void fsl_esdhc_get_cfg_common(struct fsl_esdhc_priv *priv, u32 caps; caps = esdhc_read32(®s->hostcapblt); + + /* + * For eSDHC, power supply is through peripheral circuit. Some eSDHC + * versions have value 0 of the bit but that does not reflect the + * truth. 3.3V is common for SD/MMC, and is supported for all boards + * with eSDHC in current u-boot. So, make 3.3V is supported in + * default in code. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled + * if future board does not support 3.3V. + */ + caps |= HOSTCAPBLT_VS33; + if (IS_ENABLED(CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT)) + caps &= ~HOSTCAPBLT_VS33; + if (IS_ENABLED(CONFIG_SYS_FSL_ERRATUM_ESDHC135)) caps &= ~(HOSTCAPBLT_SRS | HOSTCAPBLT_VS18 | HOSTCAPBLT_VS30); - if (IS_ENABLED(CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33)) - caps |= HOSTCAPBLT_VS33; if (caps & HOSTCAPBLT_VS18) cfg->voltages |= MMC_VDD_165_195; if (caps & HOSTCAPBLT_VS30)