From: Sylvain Lemieux Date: Thu, 13 Aug 2015 19:40:22 +0000 (-0400) Subject: usb: lpc32xx: add host USB driver X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=adf8d58d4f34533cd12174d76ae404eb740e844f;p=u-boot.git usb: lpc32xx: add host USB driver Incorporate USB driver from legacy LPCLinux NXP BSP. The files taken from the legacy patch are: - lpc32xx USB driver - lpc3250 header file USB registers definition. The legacy driver was updated and clean-up as part of the integration with the latest u-boot. Signed-off-by: Sylvain Lemieux Acked-by: Marek Vasut Tested-by: Vladimir Zapolskiy --- diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c index f0af851b5e..d9fa2807d7 100644 --- a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c +++ b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c @@ -72,6 +72,12 @@ void lpc32xx_slc_nand_init(void) writel(CLK_NAND_SLC | CLK_NAND_SLC_SELECT, &clk->flashclk_ctrl); } +void lpc32xx_usb_init(void) +{ + /* Do not route the UART 5 Tx/Rx pins to the USB D+ and USB D- pins. */ + clrbits_le32(&ctrl->ctrl, UART_CTRL_UART5_USB_MODE); +} + void lpc32xx_i2c_init(unsigned int devnum) { /* Enable I2C interface */ diff --git a/arch/arm/include/asm/arch-lpc32xx/clk.h b/arch/arm/include/asm/arch-lpc32xx/clk.h index 663f6bc777..d21310e194 100644 --- a/arch/arm/include/asm/arch-lpc32xx/clk.h +++ b/arch/arm/include/asm/arch-lpc32xx/clk.h @@ -167,6 +167,18 @@ struct clk_pm_regs { /* SDRAMCLK register bits */ #define CLK_SDRAM_DDR_SEL (1 << 1) +/* USB control register definitions */ +#define CLK_USBCTRL_PLL_STS (1 << 0) +#define CLK_USBCTRL_FDBK_PLUS1(n) (((n) & 0xFF) << 1) +#define CLK_USBCTRL_POSTDIV_2POW(n) (((n) & 0x3) << 11) +#define CLK_USBCTRL_PLL_PWRUP (1 << 16) +#define CLK_USBCTRL_CLK_EN1 (1 << 17) +#define CLK_USBCTRL_CLK_EN2 (1 << 18) +#define CLK_USBCTRL_BUS_KEEPER (0x1 << 19) +#define CLK_USBCTRL_USBHSTND_EN (1 << 21) +#define CLK_USBCTRL_USBDVND_EN (1 << 22) +#define CLK_USBCTRL_HCLK_EN (1 << 24) + unsigned int get_sys_clk_rate(void); unsigned int get_hclk_pll_rate(void); unsigned int get_hclk_clk_div(void); diff --git a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h index d6e5e683e8..eb8010f8b8 100644 --- a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h +++ b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h @@ -16,6 +16,7 @@ void lpc32xx_mlc_nand_init(void); void lpc32xx_slc_nand_init(void); void lpc32xx_i2c_init(unsigned int devnum); void lpc32xx_ssp_init(void); +void lpc32xx_usb_init(void); #if defined(CONFIG_SPL_BUILD) void ddr_init(const struct emc_dram_settings *dram); #endif diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 6cc3bbd870..7f07d7734a 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -20,6 +20,7 @@ obj-$(CONFIG_USB_SL811HS) += sl811-hcd.o obj-$(CONFIG_USB_OHCI_S3C24XX) += ohci-s3c24xx.o obj-$(CONFIG_USB_OHCI_EP93XX) += ohci-ep93xx.o obj-$(CONFIG_USB_OHCI_SUNXI) += ohci-sunxi.o +obj-$(CONFIG_USB_OHCI_LPC32XX) += ohci-lpc32xx.o # echi obj-$(CONFIG_USB_EHCI) += ehci-hcd.o diff --git a/drivers/usb/host/ohci-lpc32xx.c b/drivers/usb/host/ohci-lpc32xx.c new file mode 100644 index 0000000000..48d338e9fa --- /dev/null +++ b/drivers/usb/host/ohci-lpc32xx.c @@ -0,0 +1,231 @@ +/* + * Copyright (C) 2008 by NXP Semiconductors + * @Author: Based on code by Kevin Wells + * @Descr: USB driver - Embedded Artists LPC3250 OEM Board support functions + * + * Copyright (c) 2015 Tyco Fire Protection Products. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include + +/* OTG I2C controller module register structures */ +struct otgi2c_regs { + u32 otg_i2c_txrx; /* OTG I2C Tx/Rx Data FIFO */ + u32 otg_i2c_stat; /* OTG I2C Status Register */ + u32 otg_i2c_ctrl; /* OTG I2C Control Register */ + u32 otg_i2c_clk_hi; /* OTG I2C Clock Divider high */ + u32 otg_i2c_clk_lo; /* OTG I2C Clock Divider low */ +}; + +/* OTG controller module register structures */ +struct otg_regs { + u32 reserved1[64]; + u32 otg_int_sts; /* OTG int status register */ + u32 otg_int_enab; /* OTG int enable register */ + u32 otg_int_set; /* OTG int set register */ + u32 otg_int_clr; /* OTG int clear register */ + u32 otg_sts_ctrl; /* OTG status/control register */ + u32 otg_timer; /* OTG timer register */ + u32 reserved2[122]; + struct otgi2c_regs otg_i2c; + u32 reserved3[824]; + u32 otg_clk_ctrl; /* OTG clock control reg */ + u32 otg_clk_sts; /* OTG clock status reg */ +}; + +/* otg_sts_ctrl register definitions */ +#define OTG_HOST_EN (1 << 0) /* Enable host mode */ + +/* otg_clk_ctrl and otg_clk_sts register definitions */ +#define OTG_CLK_AHB_EN (1 << 4) /* Enable AHB clock */ +#define OTG_CLK_OTG_EN (1 << 3) /* Enable OTG clock */ +#define OTG_CLK_I2C_EN (1 << 2) /* Enable I2C clock */ +#define OTG_CLK_HOST_EN (1 << 0) /* Enable host clock */ + +/* ISP1301 USB transceiver I2C registers */ +#define MC1_SPEED_REG (1 << 0) +#define MC1_DAT_SE0 (1 << 2) +#define MC1_UART_EN (1 << 6) + +#define MC2_SPD_SUSP_CTRL (1 << 1) +#define MC2_BI_DI (1 << 2) +#define MC2_PSW_EN (1 << 6) + +#define OTG1_DP_PULLUP (1 << 0) +#define OTG1_DM_PULLUP (1 << 1) +#define OTG1_DP_PULLDOWN (1 << 2) +#define OTG1_DM_PULLDOWN (1 << 3) +#define OTG1_VBUS_DRV (1 << 5) + +#define ISP1301_I2C_ADDR CONFIG_USB_ISP1301_I2C_ADDR + +#define ISP1301_I2C_MODE_CONTROL_1_SET 0x04 +#define ISP1301_I2C_MODE_CONTROL_1_CLR 0x05 +#define ISP1301_I2C_MODE_CONTROL_2_SET 0x12 +#define ISP1301_I2C_MODE_CONTROL_2_CLR 0x13 +#define ISP1301_I2C_OTG_CONTROL_1_SET 0x06 +#define ISP1301_I2C_OTG_CONTROL_1_CLR 0x07 +#define ISP1301_I2C_INTERRUPT_LATCH_CLR 0x0B +#define ISP1301_I2C_INTERRUPT_FALLING_CLR 0x0D +#define ISP1301_I2C_INTERRUPT_RISING_CLR 0x0F + +static struct otg_regs *otg = (struct otg_regs *)USB_BASE; +static struct clk_pm_regs *clk_pwr = (struct clk_pm_regs *)CLK_PM_BASE; + +static int wait_for_bit(void *reg, const u32 mask, bool set) +{ + u32 val; + unsigned long start = get_timer(0); + + while (1) { + val = readl(reg); + if (!set) + val = ~val; + + if ((val & mask) == mask) + return 0; + + if (get_timer(start) > CONFIG_SYS_HZ) + break; + + udelay(1); + } + + error("Timeout (reg=%p mask=%08x wait_set=%i)\n", reg, mask, set); + + return -ETIMEDOUT; +} + +static int isp1301_set_value(int reg, u8 value) +{ + return i2c_write(ISP1301_I2C_ADDR, reg, 1, &value, 1); +} + +static void isp1301_configure(void) +{ + i2c_set_bus_num(I2C_2); + + /* + * LPC32XX only supports DAT_SE0 USB mode + * This sequence is important + */ + + /* Disable transparent UART mode first */ + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_CLR, MC1_UART_EN); + + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_CLR, ~MC1_SPEED_REG); + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_SET, MC1_SPEED_REG); + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_2_CLR, ~0); + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_2_SET, + MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL); + + isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_CLR, ~0); + isp1301_set_value(ISP1301_I2C_MODE_CONTROL_1_SET, MC1_DAT_SE0); + isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_SET, + OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN); + isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_CLR, + OTG1_DM_PULLUP | OTG1_DP_PULLUP); + isp1301_set_value(ISP1301_I2C_INTERRUPT_LATCH_CLR, ~0); + isp1301_set_value(ISP1301_I2C_INTERRUPT_FALLING_CLR, ~0); + isp1301_set_value(ISP1301_I2C_INTERRUPT_RISING_CLR, ~0); + + /* Enable usb_need_clk clock after transceiver is initialized */ + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_USBDVND_EN); +} + +static int usbpll_setup(void) +{ + u32 ret; + + /* make sure clocks are disabled */ + clrbits_le32(&clk_pwr->usb_ctrl, + CLK_USBCTRL_CLK_EN1 | CLK_USBCTRL_CLK_EN2); + + /* start PLL clock input */ + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_CLK_EN1); + + /* Setup PLL. */ + setbits_le32(&clk_pwr->usb_ctrl, + CLK_USBCTRL_FDBK_PLUS1(192 - 1)); + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_POSTDIV_2POW(0x01)); + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_PLL_PWRUP); + + ret = wait_for_bit(&clk_pwr->usb_ctrl, CLK_USBCTRL_PLL_STS, 1); + if (ret) + return ret; + + /* enable PLL output */ + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_CLK_EN2); + + return 0; +} + +int usb_cpu_init(void) +{ + u32 ret; + + /* + * USB pins routing setup is done by "lpc32xx_usb_init()" and should + * be call by board "board_init()" or "misc_init_r()" functions. + */ + + /* enable AHB slave USB clock */ + setbits_le32(&clk_pwr->usb_ctrl, + CLK_USBCTRL_HCLK_EN | CLK_USBCTRL_BUS_KEEPER); + + /* enable I2C clock */ + writel(OTG_CLK_I2C_EN, &otg->otg_clk_ctrl); + ret = wait_for_bit(&otg->otg_clk_sts, OTG_CLK_I2C_EN, 1); + if (ret) + return ret; + + /* Configure ISP1301 */ + isp1301_configure(); + + /* setup USB clocks and PLL */ + ret = usbpll_setup(); + if (ret) + return ret; + + /* enable usb_host_need_clk */ + setbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_USBHSTND_EN); + + /* enable all needed USB clocks */ + const u32 mask = OTG_CLK_AHB_EN | OTG_CLK_OTG_EN | + OTG_CLK_I2C_EN | OTG_CLK_HOST_EN; + writel(mask, &otg->otg_clk_ctrl); + + ret = wait_for_bit(&otg->otg_clk_sts, mask, 1); + if (ret) + return ret; + + setbits_le32(&otg->otg_sts_ctrl, OTG_HOST_EN); + isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_SET, OTG1_VBUS_DRV); + + return 0; +} + +int usb_cpu_stop(void) +{ + /* vbus off */ + isp1301_set_value(ISP1301_I2C_OTG_CONTROL_1_SET, OTG1_VBUS_DRV); + + clrbits_le32(&otg->otg_sts_ctrl, OTG_HOST_EN); + + clrbits_le32(&clk_pwr->usb_ctrl, CLK_USBCTRL_HCLK_EN); + + return 0; +} + +int usb_cpu_init_fail(void) +{ + return usb_cpu_stop(); +}