From: Dirk Eibach Date: Wed, 28 Oct 2015 10:46:32 +0000 (+0100) Subject: mpc83xx: Add strider board X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=a3f9d6c7791bbf0ff7fc68d49abcc5b53c6f7e48;p=u-boot.git mpc83xx: Add strider board The gdsys strider board is based on a Freescale MPC8308 SOC. It boots from NOR-Flash, kernel and rootfs are stored on SD-Card. On board peripherals include: - 1x 10/100 Mbit/s Ethernet (optional) - Lattice ECP3 FPGA connected via eLBC Signed-off-by: Dirk Eibach [trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now] Signed-off-by: Tom Rini --- diff --git a/arch/powerpc/cpu/mpc83xx/Kconfig b/arch/powerpc/cpu/mpc83xx/Kconfig index 3fb901f2a1..3ea62caada 100644 --- a/arch/powerpc/cpu/mpc83xx/Kconfig +++ b/arch/powerpc/cpu/mpc83xx/Kconfig @@ -67,6 +67,9 @@ config TARGET_TQM834X config TARGET_HRCON bool "Support hrcon" +config TARGET_STRIDER + bool "Support strider" + endchoice source "board/esd/vme8349/Kconfig" diff --git a/board/gdsys/common/Makefile b/board/gdsys/common/Makefile index 95e41debe5..ba48e8b9f3 100644 --- a/board/gdsys/common/Makefile +++ b/board/gdsys/common/Makefile @@ -9,7 +9,9 @@ obj-$(CONFIG_SYS_FPGA_COMMON) += fpga.o obj-$(CONFIG_CMD_IOLOOP) += cmd_ioloop.o obj-$(CONFIG_IO) += miiphybb.o obj-$(CONFIG_IO64) += miiphybb.o -obj-$(CONFIG_IOCON) += osd.o mclink.o dp501.o phy.o +obj-$(CONFIG_IOCON) += osd.o mclink.o dp501.o phy.o ch7301.o obj-$(CONFIG_DLVISION_10G) += osd.o dp501.o obj-$(CONFIG_CONTROLCENTERD) += dp501.o obj-$(CONFIG_HRCON) += osd.o mclink.o dp501.o phy.o +obj-$(CONFIG_STRIDER) += mclink.o dp501.o phy.o ioep-fpga.o adv7611.o ch7301.o +obj-$(CONFIG_STRIDER_CON) += osd.o diff --git a/board/gdsys/common/adv7611.c b/board/gdsys/common/adv7611.c new file mode 100644 index 0000000000..b728274cce --- /dev/null +++ b/board/gdsys/common/adv7611.c @@ -0,0 +1,177 @@ +/* + * (C) Copyright 2014 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include + +#define ADV7611_I2C_ADDR 0x4c +#define ADV7611_RDINFO 0x2051 + +/* + * ADV7611 I2C Addresses in u-boot notation + */ +enum { + CP_I2C_ADDR = 0x22, + DPLL_I2C_ADDR = 0x26, + KSV_I2C_ADDR = 0x32, + HDMI_I2C_ADDR = 0x34, + EDID_I2C_ADDR = 0x36, + INFOFRAME_I2C_ADDR = 0x3e, + CEC_I2C_ADDR = 0x40, + IO_I2C_ADDR = ADV7611_I2C_ADDR, +}; + +/* + * Global Control Registers + */ +enum { + IO_RD_INFO_MSB = 0xea, + IO_RD_INFO_LSB = 0xeb, + IO_CEC_ADDR = 0xf4, + IO_INFOFRAME_ADDR = 0xf5, + IO_DPLL_ADDR = 0xf8, + IO_KSV_ADDR = 0xf9, + IO_EDID_ADDR = 0xfa, + IO_HDMI_ADDR = 0xfb, + IO_CP_ADDR = 0xfd, +}; + +int adv7611_i2c[] = CONFIG_SYS_ADV7611_I2C; + +int adv7611_probe(unsigned int screen) +{ + int old_bus = i2c_get_bus_num(); + unsigned int rd_info; + int res = 0; + + i2c_set_bus_num(adv7611_i2c[screen]); + + rd_info = (i2c_reg_read(IO_I2C_ADDR, IO_RD_INFO_MSB) << 8) + | i2c_reg_read(IO_I2C_ADDR, IO_RD_INFO_LSB); + + if (rd_info != ADV7611_RDINFO) { + res = -1; + goto out; + } + + /* + * set I2C addresses to default values + */ + i2c_reg_write(IO_I2C_ADDR, IO_CEC_ADDR, CEC_I2C_ADDR << 1); + i2c_reg_write(IO_I2C_ADDR, IO_INFOFRAME_ADDR, INFOFRAME_I2C_ADDR << 1); + i2c_reg_write(IO_I2C_ADDR, IO_DPLL_ADDR, DPLL_I2C_ADDR << 1); + i2c_reg_write(IO_I2C_ADDR, IO_KSV_ADDR, KSV_I2C_ADDR << 1); + i2c_reg_write(IO_I2C_ADDR, IO_EDID_ADDR, EDID_I2C_ADDR << 1); + i2c_reg_write(IO_I2C_ADDR, IO_HDMI_ADDR, HDMI_I2C_ADDR << 1); + i2c_reg_write(IO_I2C_ADDR, IO_CP_ADDR, CP_I2C_ADDR << 1); + + /* + * do magic initialization sequence from + * "ADV7611 Register Settings Recommendations Revision 1.5" + * with most registers undocumented + */ + i2c_reg_write(CP_I2C_ADDR, 0x6c, 0x00); + i2c_reg_write(HDMI_I2C_ADDR, 0x9b, 0x03); + i2c_reg_write(HDMI_I2C_ADDR, 0x6f, 0x08); + i2c_reg_write(HDMI_I2C_ADDR, 0x85, 0x1f); + i2c_reg_write(HDMI_I2C_ADDR, 0x87, 0x70); + i2c_reg_write(HDMI_I2C_ADDR, 0x57, 0xda); + i2c_reg_write(HDMI_I2C_ADDR, 0x58, 0x01); + i2c_reg_write(HDMI_I2C_ADDR, 0x03, 0x98); + i2c_reg_write(HDMI_I2C_ADDR, 0x4c, 0x44); + + /* + * IO_REG_02, default 0xf0 + * + * INP_COLOR_SPACE (IO, Address 0x02[7:4]) + * default: 0b1111 auto + * set to : 0b0001 force RGB (range 0 to 255) input + * + * RGB_OUT (IO, Address 0x02[1]) + * default: 0 YPbPr color space output + * set to : 1 RGB color space output + */ + i2c_reg_write(IO_I2C_ADDR, 0x02, 0x12); + + /* + * IO_REG_03, default 0x00 + * + * OP_FORMAT_SEL (IO, Address 0x03[7:0]) + * default: 0x00 8-bit SDR ITU-656 mode + * set to : 0x40 24-bit 4:4:4 SDR mode + */ + i2c_reg_write(IO_I2C_ADDR, 0x03, 0x40); + + /* + * IO_REG_05, default 0x2c + * + * AVCODE_INSERT_EN (IO, Address 0x05[2]) + * default: 1 insert AV codes into data stream + * set to : 0 do not insert AV codes into data stream + */ + i2c_reg_write(IO_I2C_ADDR, 0x05, 0x28); + + /* + * IO_REG_0C, default 0x62 + * + * POWER_DOWN (IO, Address 0x0C[5]) + * default: 1 chip is powered down + * set to : 0 chip is operational + */ + i2c_reg_write(IO_I2C_ADDR, 0x0c, 0x42); + + /* + * IO_REG_15, default 0xbe + * + * TRI_SYNCS (IO, Address 0x15[3) + * TRI_LLC (IO, Address 0x15[2]) + * TRI_PIX (IO, Address 0x15[1]) + * default: 1 video output pins are tristate + * set to : 0 video output pins are active + */ + i2c_reg_write(IO_I2C_ADDR, 0x15, 0xb0); + + /* + * HDMI_REGISTER_02H, default 0xff + * + * CLOCK_TERMA_DISABLE (HDMI, Address 0x83[0]) + * default: 1 disable termination + * set to : 0 enable termination + * Future options are: + * - use the chips automatic termination control + * - set this manually on cable detect + * but at the moment this seems a safe default. + */ + i2c_reg_write(HDMI_I2C_ADDR, 0x83, 0xfe); + + /* + * HDMI_CP_CNTRL_1, default 0x01 + * + * HDMI_FRUN_EN (CP, Address 0xBA[0]) + * default: 1 Enable the free run feature in HDMI mode + * set to : 0 Disable the free run feature in HDMI mode + */ + i2c_reg_write(CP_I2C_ADDR, 0xba, 0x00); + + /* + * INT1_CONFIGURATION, default 0x20 + * + * INTRQ_DUR_SEL[1:0] (IO, Address 0x40[7:6]) + * default: 00 Interrupt signal is active for 4 Xtal periods + * set to : 11 Active until cleared + * + * INTRQ_OP_SEL[1:0] (IO, Address 0x40[1:0]) + * default: 00 Open drain + * set to : 10 Drives high when active + */ + i2c_reg_write(IO_I2C_ADDR, 0x40, 0xc2); + +out: + i2c_set_bus_num(old_bus); + + return res; +} diff --git a/board/gdsys/common/adv7611.h b/board/gdsys/common/adv7611.h new file mode 100644 index 0000000000..25a8367db6 --- /dev/null +++ b/board/gdsys/common/adv7611.h @@ -0,0 +1,13 @@ +/* + * (C) Copyright 2014 + * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _ADV7611_H_ +#define _ADV7611_H_ + +int adv7611_probe(unsigned int screen); + +#endif diff --git a/board/gdsys/common/ch7301.c b/board/gdsys/common/ch7301.c new file mode 100644 index 0000000000..c054e55cf7 --- /dev/null +++ b/board/gdsys/common/ch7301.c @@ -0,0 +1,64 @@ +/* + * (C) Copyright 2014 + * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* Chrontel CH7301C DVI Transmitter */ + +#include +#include +#include +#include + +#define CH7301_I2C_ADDR 0x75 + +enum { + CH7301_CM = 0x1c, /* Clock Mode Register */ + CH7301_IC = 0x1d, /* Input Clock Register */ + CH7301_GPIO = 0x1e, /* GPIO Control Register */ + CH7301_IDF = 0x1f, /* Input Data Format Register */ + CH7301_CD = 0x20, /* Connection Detect Register */ + CH7301_DC = 0x21, /* DAC Control Register */ + CH7301_HPD = 0x23, /* Hot Plug Detection Register */ + CH7301_TCTL = 0x31, /* DVI Control Input Register */ + CH7301_TPCP = 0x33, /* DVI PLL Charge Pump Ctrl Register */ + CH7301_TPD = 0x34, /* DVI PLL Divide Register */ + CH7301_TPVT = 0x35, /* DVI PLL Supply Control Register */ + CH7301_TPF = 0x36, /* DVI PLL Filter Register */ + CH7301_TCT = 0x37, /* DVI Clock Test Register */ + CH7301_TSTP = 0x48, /* Test Pattern Register */ + CH7301_PM = 0x49, /* Power Management register */ + CH7301_VID = 0x4a, /* Version ID Register */ + CH7301_DID = 0x4b, /* Device ID Register */ + CH7301_DSP = 0x56, /* DVI Sync polarity Register */ +}; + +int ch7301_i2c[] = CONFIG_SYS_CH7301_I2C; + +int ch7301_probe(unsigned screen, bool power) +{ + u8 value; + + i2c_set_bus_num(ch7301_i2c[screen]); + if (i2c_probe(CH7301_I2C_ADDR)) + return -1; + + value = i2c_reg_read(CH7301_I2C_ADDR, CH7301_DID); + if (value != 0x17) + return -1; + + if (power) { + i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPCP, 0x08); + i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPD, 0x16); + i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPF, 0x60); + i2c_reg_write(CH7301_I2C_ADDR, CH7301_DC, 0x09); + i2c_reg_write(CH7301_I2C_ADDR, CH7301_PM, 0xc0); + } else { + i2c_reg_write(CH7301_I2C_ADDR, CH7301_DC, 0x00); + i2c_reg_write(CH7301_I2C_ADDR, CH7301_PM, 0x01); + } + + return 0; +} diff --git a/board/gdsys/common/ch7301.h b/board/gdsys/common/ch7301.h new file mode 100644 index 0000000000..8383719808 --- /dev/null +++ b/board/gdsys/common/ch7301.h @@ -0,0 +1,13 @@ +/* + * (C) Copyright 2014 + * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CH7301_H_ +#define _CH7301_H_ + +int ch7301_probe(unsigned screen, bool power); + +#endif diff --git a/board/gdsys/common/ioep-fpga.c b/board/gdsys/common/ioep-fpga.c new file mode 100644 index 0000000000..18d37dcb41 --- /dev/null +++ b/board/gdsys/common/ioep-fpga.c @@ -0,0 +1,227 @@ +/* + * (C) Copyright 2014 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include + +#include + +enum { + UNITTYPE_MAIN_SERVER = 0, + UNITTYPE_MAIN_USER = 1, + UNITTYPE_VIDEO_SERVER = 2, + UNITTYPE_VIDEO_USER = 3, +}; + +enum { + UNITTYPEPCB_DVI = 0, + UNITTYPEPCB_DP_165 = 1, + UNITTYPEPCB_DP_300 = 2, + UNITTYPEPCB_HDMI = 3, +}; + +enum { + COMPRESSION_NONE = 0, + COMPRESSION_TYPE1_DELTA = 1, + COMPRESSION_TYPE1_TYPE2_DELTA = 3, +}; + +enum { + AUDIO_NONE = 0, + AUDIO_TX = 1, + AUDIO_RX = 2, + AUDIO_RXTX = 3, +}; + +enum { + SYSCLK_147456 = 0, +}; + +enum { + RAM_DDR2_32 = 0, + RAM_DDR3_32 = 1, +}; + +enum { + CARRIER_SPEED_1G = 0, + CARRIER_SPEED_2_5G = 1, +}; + +bool ioep_fpga_has_osd(unsigned int fpga) +{ + u16 fpga_features; + unsigned feature_osd; + + FPGA_GET_REG(0, fpga_features, &fpga_features); + feature_osd = fpga_features & (1<<11); + + return feature_osd; +} + +void ioep_fpga_print_info(unsigned int fpga) +{ + u16 versions; + u16 fpga_version; + u16 fpga_features; + unsigned unit_type; + unsigned unit_type_pcb_video; + unsigned feature_compression; + unsigned feature_osd; + unsigned feature_audio; + unsigned feature_sysclock; + unsigned feature_ramconfig; + unsigned feature_carrier_speed; + unsigned feature_carriers; + unsigned feature_video_channels; + + FPGA_GET_REG(fpga, versions, &versions); + FPGA_GET_REG(fpga, fpga_version, &fpga_version); + FPGA_GET_REG(fpga, fpga_features, &fpga_features); + + unit_type = (versions & 0xf000) >> 12; + unit_type_pcb_video = (versions & 0x01c0) >> 6; + feature_compression = (fpga_features & 0xe000) >> 13; + feature_osd = fpga_features & (1<<11); + feature_audio = (fpga_features & 0x0600) >> 9; + feature_sysclock = (fpga_features & 0x0180) >> 7; + feature_ramconfig = (fpga_features & 0x0060) >> 5; + feature_carrier_speed = fpga_features & (1<<4); + feature_carriers = (fpga_features & 0x000c) >> 2; + feature_video_channels = fpga_features & 0x0003; + + switch (unit_type) { + case UNITTYPE_MAIN_SERVER: + case UNITTYPE_MAIN_USER: + printf("Mainchannel"); + break; + + case UNITTYPE_VIDEO_SERVER: + case UNITTYPE_VIDEO_USER: + printf("Videochannel"); + break; + + default: + printf("UnitType %d(not supported)", unit_type); + break; + } + + switch (unit_type) { + case UNITTYPE_MAIN_SERVER: + case UNITTYPE_VIDEO_SERVER: + printf(" Server"); + if (versions & (1<<4)) + printf(" UC"); + break; + + case UNITTYPE_MAIN_USER: + case UNITTYPE_VIDEO_USER: + printf(" User"); + break; + + default: + break; + } + + if (versions & (1<<5)) + printf(" Fiber"); + else + printf(" CAT"); + + switch (unit_type_pcb_video) { + case UNITTYPEPCB_DVI: + printf(" DVI,"); + break; + + case UNITTYPEPCB_DP_165: + printf(" DP 165MPix/s,"); + break; + + case UNITTYPEPCB_DP_300: + printf(" DP 300MPix/s,"); + break; + + case UNITTYPEPCB_HDMI: + printf(" HDMI,"); + break; + } + + printf(" FPGA V %d.%02d\n features:", + fpga_version / 100, fpga_version % 100); + + + switch (feature_compression) { + case COMPRESSION_NONE: + printf(" no compression"); + break; + + case COMPRESSION_TYPE1_DELTA: + printf(" type1-deltacompression"); + break; + + case COMPRESSION_TYPE1_TYPE2_DELTA: + printf(" type1-deltacompression, type2-inlinecompression"); + break; + + default: + printf(" compression %d(not supported)", feature_compression); + break; + } + + printf(", %sosd", feature_osd ? "" : "no "); + + switch (feature_audio) { + case AUDIO_NONE: + printf(", no audio"); + break; + + case AUDIO_TX: + printf(", audio tx"); + break; + + case AUDIO_RX: + printf(", audio rx"); + break; + + case AUDIO_RXTX: + printf(", audio rx+tx"); + break; + + default: + printf(", audio %d(not supported)", feature_audio); + break; + } + + puts(",\n "); + + switch (feature_sysclock) { + case SYSCLK_147456: + printf("clock 147.456 MHz"); + break; + + default: + printf("clock %d(not supported)", feature_sysclock); + break; + } + + switch (feature_ramconfig) { + case RAM_DDR2_32: + printf(", RAM 32 bit DDR2"); + break; + + case RAM_DDR3_32: + printf(", RAM 32 bit DDR3"); + break; + + default: + printf(", RAM %d(not supported)", feature_ramconfig); + break; + } + + printf(", %d carrier(s) %s", feature_carriers, + feature_carrier_speed ? "2.5Gbit/s" : "1Gbit/s"); + + printf(", %d video channel(s)\n", feature_video_channels); +} diff --git a/board/gdsys/common/ioep-fpga.h b/board/gdsys/common/ioep-fpga.h new file mode 100644 index 0000000000..44f71399e7 --- /dev/null +++ b/board/gdsys/common/ioep-fpga.h @@ -0,0 +1,14 @@ +/* + * (C) Copyright 2014 + * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _IOEP_FPGA_H_ +#define _IOEP_FPGA_H_ + +void ioep_fpga_print_info(unsigned int fpga); +bool ioep_fpga_has_osd(unsigned int fpga); + +#endif diff --git a/board/gdsys/common/osd.c b/board/gdsys/common/osd.c index 55ecdf1012..f11e26f5fa 100644 --- a/board/gdsys/common/osd.c +++ b/board/gdsys/common/osd.c @@ -9,11 +9,10 @@ #include #include +#include "ch7301.h" #include "dp501.h" #include -#define CH7301_I2C_ADDR 0x75 - #define ICS8N3QV01_I2C_ADDR 0x6E #define ICS8N3QV01_FREF 114285000 #define ICS8N3QV01_FREF_LL 114285000LL @@ -29,27 +28,6 @@ #define PIXCLK_640_480_60 25180000 -enum { - CH7301_CM = 0x1c, /* Clock Mode Register */ - CH7301_IC = 0x1d, /* Input Clock Register */ - CH7301_GPIO = 0x1e, /* GPIO Control Register */ - CH7301_IDF = 0x1f, /* Input Data Format Register */ - CH7301_CD = 0x20, /* Connection Detect Register */ - CH7301_DC = 0x21, /* DAC Control Register */ - CH7301_HPD = 0x23, /* Hot Plug Detection Register */ - CH7301_TCTL = 0x31, /* DVI Control Input Register */ - CH7301_TPCP = 0x33, /* DVI PLL Charge Pump Ctrl Register */ - CH7301_TPD = 0x34, /* DVI PLL Divide Register */ - CH7301_TPVT = 0x35, /* DVI PLL Supply Control Register */ - CH7301_TPF = 0x36, /* DVI PLL Filter Register */ - CH7301_TCT = 0x37, /* DVI Clock Test Register */ - CH7301_TSTP = 0x48, /* Test Pattern Register */ - CH7301_PM = 0x49, /* Power Management register */ - CH7301_VID = 0x4a, /* Version ID Register */ - CH7301_DID = 0x4b, /* Device ID Register */ - CH7301_DSP = 0x56, /* DVI Sync polarity Register */ -}; - unsigned int base_width; unsigned int base_height; size_t bufsize; @@ -61,10 +39,6 @@ unsigned int max_osd_screen = CONFIG_SYS_OSD_SCREENS - 1; int ics8n3qv01_i2c[] = CONFIG_SYS_ICS8N3QV01_I2C; #endif -#ifdef CONFIG_SYS_CH7301_I2C -int ch7301_i2c[] = CONFIG_SYS_CH7301_I2C; -#endif - #ifdef CONFIG_SYS_SIL1178_I2C int sil1178_i2c[] = CONFIG_SYS_SIL1178_I2C; #endif @@ -327,19 +301,8 @@ int osd_probe(unsigned screen) /* setup output driver */ #ifdef CONFIG_SYS_CH7301_I2C - i2c_set_bus_num(ch7301_i2c[screen]); - if (!i2c_probe(CH7301_I2C_ADDR)) { - u8 value = i2c_reg_read(CH7301_I2C_ADDR, CH7301_DID); - - if (value == 0x17) { - i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPCP, 0x08); - i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPD, 0x16); - i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPF, 0x60); - i2c_reg_write(CH7301_I2C_ADDR, CH7301_DC, 0x09); - i2c_reg_write(CH7301_I2C_ADDR, CH7301_PM, 0xc0); - output_driver_present = true; - } - } + if (!ch7301_probe(screen, true)) + output_driver_present = true; #endif #ifdef CONFIG_SYS_SIL1178_I2C diff --git a/board/gdsys/common/osd.h b/board/gdsys/common/osd.h index 440b276a0b..5b3f14bf05 100644 --- a/board/gdsys/common/osd.h +++ b/board/gdsys/common/osd.h @@ -8,6 +8,7 @@ #ifndef _OSD_H_ #define _OSD_H_ +int ch7301_probe(unsigned screen, bool power); int osd_probe(unsigned screen); #endif diff --git a/board/gdsys/mpc8308/Kconfig b/board/gdsys/mpc8308/Kconfig index 43e1663d19..9a1a3a2f28 100644 --- a/board/gdsys/mpc8308/Kconfig +++ b/board/gdsys/mpc8308/Kconfig @@ -10,3 +10,16 @@ config SYS_CONFIG_NAME default "hrcon" endif + +if TARGET_STRIDER + +config SYS_BOARD + default "mpc8308" + +config SYS_VENDOR + default "gdsys" + +config SYS_CONFIG_NAME + default "strider" + +endif diff --git a/board/gdsys/mpc8308/MAINTAINERS b/board/gdsys/mpc8308/MAINTAINERS index a7853a59df..35704bc871 100644 --- a/board/gdsys/mpc8308/MAINTAINERS +++ b/board/gdsys/mpc8308/MAINTAINERS @@ -4,3 +4,6 @@ S: Maintained F: board/gdsys/mpc8308/ F: include/configs/hrcon.h F: configs/hrcon_defconfig +F: include/configs/strider.h +F: configs/strider_cpu_defconfig +F: configs/strider_con_defconfig diff --git a/board/gdsys/mpc8308/Makefile b/board/gdsys/mpc8308/Makefile index b5dfdbb190..42702fb967 100644 --- a/board/gdsys/mpc8308/Makefile +++ b/board/gdsys/mpc8308/Makefile @@ -7,3 +7,4 @@ obj-y := mpc8308.o sdram.o obj-$(CONFIG_HRCON) += hrcon.o +obj-$(CONFIG_STRIDER) += strider.o diff --git a/board/gdsys/mpc8308/strider.c b/board/gdsys/mpc8308/strider.c new file mode 100644 index 0000000000..8e5d5de8f7 --- /dev/null +++ b/board/gdsys/mpc8308/strider.c @@ -0,0 +1,501 @@ +/* + * (C) Copyright 2014 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "mpc8308.h" + +#include + +#include "../common/adv7611.h" +#include "../common/ch7301.h" +#include "../common/ioep-fpga.h" +#include "../common/mclink.h" +#include "../common/osd.h" +#include "../common/phy.h" + +#include +#include + +#include + +DECLARE_GLOBAL_DATA_PTR; + +#define MAX_MUX_CHANNELS 2 + +enum { + MCFPGA_DONE = 1 << 0, + MCFPGA_INIT_N = 1 << 1, + MCFPGA_PROGRAM_N = 1 << 2, + MCFPGA_UPDATE_ENABLE_N = 1 << 3, + MCFPGA_RESET_N = 1 << 4, +}; + +enum { + GPIO_MDC = 1 << 14, + GPIO_MDIO = 1 << 15, +}; + +enum { + FAN_CONFIG = 0x03, + FAN_TACHLIM_LSB = 0x48, + FAN_TACHLIM_MSB = 0x49, + FAN_PWM_FREQ = 0x4D, +}; + +unsigned int mclink_fpgacount; +struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR; + +struct { + u8 bus; + u8 addr; +} strider_fans[] = CONFIG_STRIDER_FANS; + +int fpga_set_reg(u32 fpga, u16 *reg, off_t regoff, u16 data) +{ + int res; + + switch (fpga) { + case 0: + out_le16(reg, data); + break; + default: + res = mclink_send(fpga - 1, regoff, data); + if (res < 0) { + printf("mclink_send reg %02lx data %04x returned %d\n", + regoff, data, res); + return res; + } + break; + } + + return 0; +} + +int fpga_get_reg(u32 fpga, u16 *reg, off_t regoff, u16 *data) +{ + int res; + + switch (fpga) { + case 0: + *data = in_le16(reg); + break; + default: + if (fpga > mclink_fpgacount) + return -EINVAL; + res = mclink_receive(fpga - 1, regoff, data); + if (res < 0) { + printf("mclink_receive reg %02lx returned %d\n", + regoff, res); + return res; + } + } + + return 0; +} + +int checkboard(void) +{ + char *s = getenv("serial#"); + bool hw_type_cat = pca9698_get_value(0x20, 18); + + puts("Board: "); + + printf("Strider %s", hw_type_cat ? "CAT" : "Fiber"); + + if (s != NULL) { + puts(", serial# "); + puts(s); + } + + puts("\n"); + + return 0; +} + +static void init_fan_controller(u8 addr) +{ + int val; + + /* set PWM Frequency to 2.5% resolution */ + i2c_reg_write(addr, FAN_PWM_FREQ, 20); + + /* set Tachometer Limit */ + i2c_reg_write(addr, FAN_TACHLIM_LSB, 0x10); + i2c_reg_write(addr, FAN_TACHLIM_MSB, 0x0a); + + /* enable Tach input */ + val = i2c_reg_read(addr, FAN_CONFIG) | 0x04; + i2c_reg_write(addr, FAN_CONFIG, val); +} + +int last_stage_init(void) +{ + int slaves; + unsigned int k; + unsigned int mux_ch; + unsigned char mclink_controllers[] = { 0x3c, 0x3d, 0x3e }; + bool hw_type_cat = pca9698_get_value(0x20, 18); + bool ch0_sgmii2_present = false; + + /* Turn on Analog Devices ADV7611 */ + pca9698_direction_output(0x20, 8, 0); + + /* Turn on Parade DP501 */ + pca9698_direction_output(0x20, 9, 1); + + ch0_sgmii2_present = !pca9698_get_value(0x20, 37); + + /* wait for FPGA done, then reset FPGA */ + for (k = 0; k < ARRAY_SIZE(mclink_controllers); ++k) { + unsigned int ctr = 0; + + if (i2c_probe(mclink_controllers[k])) + continue; + + while (!(pca953x_get_val(mclink_controllers[k]) + & MCFPGA_DONE)) { + udelay(100000); + if (ctr++ > 5) { + printf("no done for mclink_controller %d\n", k); + break; + } + } + + pca953x_set_dir(mclink_controllers[k], MCFPGA_RESET_N, 0); + pca953x_set_val(mclink_controllers[k], MCFPGA_RESET_N, 0); + udelay(10); + pca953x_set_val(mclink_controllers[k], MCFPGA_RESET_N, + MCFPGA_RESET_N); + } + + if (hw_type_cat) { + miiphy_register(bb_miiphy_buses[0].name, bb_miiphy_read, + bb_miiphy_write); + for (mux_ch = 0; mux_ch < MAX_MUX_CHANNELS; ++mux_ch) { + if ((mux_ch == 1) && !ch0_sgmii2_present) + continue; + + setup_88e1514(bb_miiphy_buses[0].name, mux_ch); + } + } + + /* give slave-PLLs and Parade DP501 some time to be up and running */ + udelay(500000); + + mclink_fpgacount = CONFIG_SYS_MCLINK_MAX; + slaves = mclink_probe(); + mclink_fpgacount = 0; + + ioep_fpga_print_info(0); + + if (!adv7611_probe(0)) + printf(" Advantiv ADV7611 HDMI Receiver\n"); + +#ifdef CONFIG_STRIDER_CON + if (ioep_fpga_has_osd(0)) + osd_probe(0); +#endif + +#ifdef CONFIG_STRIDER_CPU + ch7301_probe(0, false); +#endif + + if (slaves <= 0) + return 0; + + mclink_fpgacount = slaves; + + for (k = 1; k <= slaves; ++k) { + ioep_fpga_print_info(k); +#ifdef CONFIG_STRIDER_CON + if (ioep_fpga_has_osd(k)) + osd_probe(k); +#endif +#ifdef CONFIG_STRIDER_CPU + FPGA_SET_REG(k, extended_control, 0); /* enable video in*/ + if (!adv7611_probe(k)) + printf(" Advantiv ADV7611 HDMI Receiver\n"); + ch7301_probe(k, false); +#endif + if (hw_type_cat) { + miiphy_register(bb_miiphy_buses[k].name, + bb_miiphy_read, bb_miiphy_write); + setup_88e1514(bb_miiphy_buses[k].name, 0); + } + } + + for (k = 0; k < ARRAY_SIZE(strider_fans); ++k) { + i2c_set_bus_num(strider_fans[k].bus); + init_fan_controller(strider_fans[k].addr); + } + + return 0; +} + +/* + * provide access to fpga gpios (for I2C bitbang) + * (these may look all too simple but make iocon.h much more readable) + */ +void fpga_gpio_set(unsigned int bus, int pin) +{ + FPGA_SET_REG(bus, gpio.set, pin); +} + +void fpga_gpio_clear(unsigned int bus, int pin) +{ + FPGA_SET_REG(bus, gpio.clear, pin); +} + +int fpga_gpio_get(unsigned int bus, int pin) +{ + u16 val; + + FPGA_GET_REG(bus, gpio.read, &val); + + return val & pin; +} + +void mpc8308_init(void) +{ + pca9698_direction_output(0x20, 26, 1); +} + +void mpc8308_set_fpga_reset(unsigned state) +{ + pca9698_set_value(0x20, 26, state ? 0 : 1); +} + +void mpc8308_setup_hw(void) +{ + immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; + + /* + * set "startup-finished"-gpios + */ + setbits_be32(&immr->gpio[0].dir, (1 << (31-11)) | (1 << (31-12))); + setbits_be32(&immr->gpio[0].dat, 1 << (31-12)); +} + +int mpc8308_get_fpga_done(unsigned fpga) +{ + return pca9698_get_value(0x20, 20); +} + +#ifdef CONFIG_FSL_ESDHC +int board_mmc_init(bd_t *bd) +{ + immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; + sysconf83xx_t *sysconf = &immr->sysconf; + + /* Enable cache snooping in eSDHC system configuration register */ + out_be32(&sysconf->sdhccr, 0x02000000); + + return fsl_esdhc_mmc_init(bd); +} +#endif + +static struct pci_region pcie_regions_0[] = { + { + .bus_start = CONFIG_SYS_PCIE1_MEM_BASE, + .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS, + .size = CONFIG_SYS_PCIE1_MEM_SIZE, + .flags = PCI_REGION_MEM, + }, + { + .bus_start = CONFIG_SYS_PCIE1_IO_BASE, + .phys_start = CONFIG_SYS_PCIE1_IO_PHYS, + .size = CONFIG_SYS_PCIE1_IO_SIZE, + .flags = PCI_REGION_IO, + }, +}; + +void pci_init_board(void) +{ + immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; + sysconf83xx_t *sysconf = &immr->sysconf; + law83xx_t *pcie_law = sysconf->pcielaw; + struct pci_region *pcie_reg[] = { pcie_regions_0 }; + + fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX, + FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V); + + /* Deassert the resets in the control register */ + out_be32(&sysconf->pecr1, 0xE0008000); + udelay(2000); + + /* Configure PCI Express Local Access Windows */ + out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR); + out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB); + + mpc83xx_pcie_init(1, pcie_reg); +} + +ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info) +{ + info->portwidth = FLASH_CFI_16BIT; + info->chipwidth = FLASH_CFI_BY16; + info->interface = FLASH_CFI_X16; + return 1; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +int ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); + fdt_fixup_dr_usb(blob, bd); + fdt_fixup_esdhc(blob, bd); + + return 0; +} +#endif + +/* + * FPGA MII bitbang implementation + */ + +struct fpga_mii { + unsigned fpga; + int mdio; +} fpga_mii[] = { + { 0, 1}, + { 1, 1}, + { 2, 1}, + { 3, 1}, +}; + +static int mii_dummy_init(struct bb_miiphy_bus *bus) +{ + return 0; +} + +static int mii_mdio_active(struct bb_miiphy_bus *bus) +{ + struct fpga_mii *fpga_mii = bus->priv; + + if (fpga_mii->mdio) + FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO); + else + FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO); + + return 0; +} + +static int mii_mdio_tristate(struct bb_miiphy_bus *bus) +{ + struct fpga_mii *fpga_mii = bus->priv; + + FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO); + + return 0; +} + +static int mii_set_mdio(struct bb_miiphy_bus *bus, int v) +{ + struct fpga_mii *fpga_mii = bus->priv; + + if (v) + FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO); + else + FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO); + + fpga_mii->mdio = v; + + return 0; +} + +static int mii_get_mdio(struct bb_miiphy_bus *bus, int *v) +{ + u16 gpio; + struct fpga_mii *fpga_mii = bus->priv; + + FPGA_GET_REG(fpga_mii->fpga, gpio.read, &gpio); + + *v = ((gpio & GPIO_MDIO) != 0); + + return 0; +} + +static int mii_set_mdc(struct bb_miiphy_bus *bus, int v) +{ + struct fpga_mii *fpga_mii = bus->priv; + + if (v) + FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDC); + else + FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDC); + + return 0; +} + +static int mii_delay(struct bb_miiphy_bus *bus) +{ + udelay(1); + + return 0; +} + +struct bb_miiphy_bus bb_miiphy_buses[] = { + { + .name = "board0", + .init = mii_dummy_init, + .mdio_active = mii_mdio_active, + .mdio_tristate = mii_mdio_tristate, + .set_mdio = mii_set_mdio, + .get_mdio = mii_get_mdio, + .set_mdc = mii_set_mdc, + .delay = mii_delay, + .priv = &fpga_mii[0], + }, + { + .name = "board1", + .init = mii_dummy_init, + .mdio_active = mii_mdio_active, + .mdio_tristate = mii_mdio_tristate, + .set_mdio = mii_set_mdio, + .get_mdio = mii_get_mdio, + .set_mdc = mii_set_mdc, + .delay = mii_delay, + .priv = &fpga_mii[1], + }, + { + .name = "board2", + .init = mii_dummy_init, + .mdio_active = mii_mdio_active, + .mdio_tristate = mii_mdio_tristate, + .set_mdio = mii_set_mdio, + .get_mdio = mii_get_mdio, + .set_mdc = mii_set_mdc, + .delay = mii_delay, + .priv = &fpga_mii[2], + }, + { + .name = "board3", + .init = mii_dummy_init, + .mdio_active = mii_mdio_active, + .mdio_tristate = mii_mdio_tristate, + .set_mdio = mii_set_mdio, + .get_mdio = mii_get_mdio, + .set_mdc = mii_set_mdc, + .delay = mii_delay, + .priv = &fpga_mii[3], + }, +}; + +int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) / + sizeof(bb_miiphy_buses[0]); diff --git a/configs/strider_con_defconfig b/configs/strider_con_defconfig new file mode 100644 index 0000000000..74ef69e855 --- /dev/null +++ b/configs/strider_con_defconfig @@ -0,0 +1,7 @@ +CONFIG_SYS_EXTRA_OPTIONS="STRIDER_CON" +CONFIG_PPC=y +CONFIG_MPC83xx=y +CONFIG_TARGET_STRIDER=y +CONFIG_AUTOBOOT_KEYED=y +CONFIG_AUTOBOOT_STOP_STR=" " +# CONFIG_CMD_SETEXPR is not set diff --git a/configs/strider_cpu_defconfig b/configs/strider_cpu_defconfig new file mode 100644 index 0000000000..fc0a8233b3 --- /dev/null +++ b/configs/strider_cpu_defconfig @@ -0,0 +1,7 @@ +CONFIG_SYS_EXTRA_OPTIONS="STRIDER_CPU" +CONFIG_PPC=y +CONFIG_MPC83xx=y +CONFIG_TARGET_STRIDER=y +CONFIG_AUTOBOOT_KEYED=y +CONFIG_AUTOBOOT_STOP_STR=" " +# CONFIG_CMD_SETEXPR is not set diff --git a/include/configs/strider.h b/include/configs/strider.h new file mode 100644 index 0000000000..fb7b7f9551 --- /dev/null +++ b/include/configs/strider.h @@ -0,0 +1,651 @@ +/* + * (C) Copyright 2014 + * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de + * + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_MPC83xx 1 /* MPC83xx family */ +#define CONFIG_MPC830x 1 /* MPC830x family */ +#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ +#define CONFIG_STRIDER 1 /* STRIDER board specific */ + +#define CONFIG_SYS_TEXT_BASE 0xFE000000 + +#ifdef CONFIG_STRIDER_CPU +#define CONFIG_IDENT_STRING " strider cpu 0.01" +#else +#define CONFIG_IDENT_STRING " strider con 0.01" +#endif + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_LAST_STAGE_INIT + +/* new uImage format support */ +#define CONFIG_FIT 1 +#define CONFIG_FIT_VERBOSE 1 + +#define CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR +#define CONFIG_SYS_FSL_ERRATUM_ESDHC111 + +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT2 + +#define CONFIG_CMD_MEMTEST +#define CONFIG_SYS_ALT_MEMTEST + +#define CONFIG_CMD_FPGAD +#define CONFIG_CMD_IOLOOP + +/* + * System Clock Setup + */ +#define CONFIG_83XX_CLKIN 33333333 /* in Hz */ +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN + +/* + * Hardware Reset Configuration Word + * if CLKIN is 66.66MHz, then + * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz + * We choose the A type silicon as default, so the core is 400Mhz. + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_SVCOD_DIV_2 |\ + HRCWL_CSB_TO_CLKIN_4X1 |\ + HRCWL_CORE_TO_CSB_3X1) +/* + * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits + * in 8308's HRCWH according to the manual, but original Freescale's + * code has them and I've expirienced some problems using the board + * with BDI3000 attached when I've tried to set these bits to zero + * (UART doesn't work after the 'reset run' command). + */ +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0XFFF00100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_MII |\ + HRCWH_TSEC2M_IN_RGMII |\ + HRCWH_BIG_ENDIAN) + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRH (\ + SICRH_ESDHC_A_SD |\ + SICRH_ESDHC_B_SD |\ + SICRH_ESDHC_C_SD |\ + SICRH_GPIO_A_GPIO |\ + SICRH_GPIO_B_GPIO |\ + SICRH_IEEE1588_A_GPIO |\ + SICRH_USB |\ + SICRH_GTM_GPIO |\ + SICRH_IEEE1588_B_GPIO |\ + SICRH_ETSEC2_GPIO |\ + SICRH_GPIOSEL_1 |\ + SICRH_TMROBI_V3P3 |\ + SICRH_TSOBI1_V2P5 |\ + SICRH_TSOBI2_V2P5) /* 0x0037f103 */ +#define CONFIG_SYS_SICRL (\ + SICRL_SPI_PF0 |\ + SICRL_UART_PF0 |\ + SICRL_IRQ_PF0 |\ + SICRL_I2C2_PF0 |\ + SICRL_ETSEC1_TX_CLK) /* 0x00000000 */ + +/* + * IMMR new address + */ +#define CONFIG_SYS_IMMR 0xE0000000 + +/* + * SERDES + */ +#define CONFIG_FSL_SERDES +#define CONFIG_FSL_SERDES1 0xe3000 + +/* + * Arbiter Setup + */ +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ +#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ + +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ + | DDRCDR_PZ_LOZ \ + | DDRCDR_NZ_LOZ \ + | DDRCDR_ODT \ + | DDRCDR_Q_DRN) + /* 0x7b880001 */ +/* + * Manually set up DDR parameters + * consist of one chip NT5TU64M16HG from NANYA + */ + +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ + +#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ + | CSCONFIG_ODT_RD_NEVER \ + | CSCONFIG_ODT_WR_ONLY_CURRENT \ + | CSCONFIG_BANK_BIT_3 \ + | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) + /* 0x80010102 */ +#define CONFIG_SYS_DDR_TIMING_3 0 +#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ + | (0 << TIMING_CFG0_WRT_SHIFT) \ + | (0 << TIMING_CFG0_RRT_SHIFT) \ + | (0 << TIMING_CFG0_WWT_SHIFT) \ + | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ + | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ + | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) + /* 0x00260802 */ +#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ + | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ + | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ + | (7 << TIMING_CFG1_CASLAT_SHIFT) \ + | (9 << TIMING_CFG1_REFREC_SHIFT) \ + | (2 << TIMING_CFG1_WRREC_SHIFT) \ + | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ + | (2 << TIMING_CFG1_WRTORD_SHIFT)) + /* 0x26279222 */ +#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ + | (4 << TIMING_CFG2_CPO_SHIFT) \ + | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ + | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ + | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ + | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ + | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) + /* 0x021848c5 */ +#define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \ + | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + /* 0x08240100 */ +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_DBW_16) + /* 0x43100000 */ + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ +#define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ + | (0x0242 << SDRAM_MODE_SD_SHIFT)) + /* ODT 150ohm CL=4, AL=0 on SDRAM */ +#define CONFIG_SYS_DDR_MODE2 0x00000000 + +/* + * Memory test + */ +#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x07f00000 + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 +#define CONFIG_SYS_LBC_LBCR 0x00040000 + +/* + * FLASH on the Local Bus + */ +#if 1 +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +#define CONFIG_FLASH_CFI_LEGACY +#define CONFIG_SYS_FLASH_LEGACY_512Kx16 +#else +#define CONFIG_SYS_NO_FLASH +#endif + +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ + +/* Window base at flash base */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) + +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ + | BR_PS_16 /* 16 bit port */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV2 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX_SET \ + | OR_GPCM_EHTR_SET) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 135 + +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +/* + * FPGA + */ +#define CONFIG_SYS_FPGA0_BASE 0xE0600000 +#define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */ + +/* Window base at FPGA base */ +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE +#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB) + +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \ + | BR_PS_16 /* 16 bit port */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV2 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX_SET \ + | OR_GPCM_EHTR_SET) + +#define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE +#define CONFIG_SYS_FPGA_DONE(k) 0x0010 + +#define CONFIG_SYS_FPGA_COUNT 1 + +#define CONFIG_SYS_MCLINK_MAX 3 + +#define CONFIG_SYS_FPGA_PTR \ + { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL } + +#define CONFIG_SYS_FPGA_NO_RFL_HI + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 2 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 + +#define CONFIG_PCA953X /* NXP PCA9554 */ +#define CONFIG_PCA9698 /* NXP PCA9698 */ + +#define CONFIG_SYS_I2C_IHS +#define CONFIG_SYS_I2C_IHS_CH0 +#define CONFIG_SYS_I2C_IHS_SPEED_0 50000 +#define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F +#define CONFIG_SYS_I2C_IHS_CH1 +#define CONFIG_SYS_I2C_IHS_SPEED_1 50000 +#define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F +#define CONFIG_SYS_I2C_IHS_CH2 +#define CONFIG_SYS_I2C_IHS_SPEED_2 50000 +#define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F +#define CONFIG_SYS_I2C_IHS_CH3 +#define CONFIG_SYS_I2C_IHS_SPEED_3 50000 +#define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F + +/* + * Software (bit-bang) I2C driver configuration + */ +#define CONFIG_SYS_I2C_SOFT +#define CONFIG_SOFT_I2C_READ_REPEATED_START +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F +#define I2C_SOFT_DECLARATIONS2 +#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F +#define I2C_SOFT_DECLARATIONS3 +#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F +#define I2C_SOFT_DECLARATIONS4 +#define CONFIG_SYS_I2C_SOFT_SPEED_4 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F +#ifdef CONFIG_STRIDER_CON +#define I2C_SOFT_DECLARATIONS5 +#define CONFIG_SYS_I2C_SOFT_SPEED_5 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_5 0x7F +#define I2C_SOFT_DECLARATIONS6 +#define CONFIG_SYS_I2C_SOFT_SPEED_6 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_6 0x7F +#define I2C_SOFT_DECLARATIONS7 +#define CONFIG_SYS_I2C_SOFT_SPEED_7 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_7 0x7F +#define I2C_SOFT_DECLARATIONS8 +#define CONFIG_SYS_I2C_SOFT_SPEED_8 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_8 0x7F +#endif + +#ifdef CONFIG_STRIDER_CON +#define CONFIG_SYS_ICS8N3QV01_I2C {5, 6, 7, 8} +#define CONFIG_SYS_CH7301_I2C {5, 6, 7, 8} +#define CONFIG_SYS_ADV7611_I2C {5, 6, 7, 8} +#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} +#define CONFIG_STRIDER_FANS { {10, 0x4c}, {11, 0x4c}, \ + {12, 0x4c} } +#else +#define CONFIG_SYS_CH7301_I2C {1, 2, 3, 4} +#define CONFIG_SYS_ADV7611_I2C {1, 2, 3, 4} +#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} +#define CONFIG_STRIDER_FANS { {2, 0x18}, {3, 0x18}, \ + {4, 0x18} } +#endif + +#ifndef __ASSEMBLY__ +void fpga_gpio_set(unsigned int bus, int pin); +void fpga_gpio_clear(unsigned int bus, int pin); +int fpga_gpio_get(unsigned int bus, int pin); +#endif + +#ifdef CONFIG_STRIDER_CON +#define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0200 : 0x0040) +#define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0100 : 0x0020) +#define I2C_FPGA_IDX ((I2C_ADAP_HWNR > 3) ? \ + (I2C_ADAP_HWNR - 4) : I2C_ADAP_HWNR) +#else +#define I2C_SDA_GPIO 0x0040 +#define I2C_SCL_GPIO 0x0020 +#define I2C_FPGA_IDX I2C_ADAP_HWNR +#endif +#define I2C_ACTIVE { } +#define I2C_TRISTATE { } +#define I2C_READ \ + (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0) +#define I2C_SDA(bit) \ + do { \ + if (bit) \ + fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \ + else \ + fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \ + } while (0) +#define I2C_SCL(bit) \ + do { \ + if (bit) \ + fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \ + else \ + fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \ + } while (0) +#define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */ + +/* + * Software (bit-bang) MII driver configuration + */ +#define CONFIG_BITBANGMII /* bit-bang MII PHY management */ +#define CONFIG_BITBANGMII_MULTI + +/* + * OSD Setup + */ +#define CONFIG_SYS_OSD_SCREENS 1 +#define CONFIG_SYS_DP501_DIFFERENTIAL +#define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCIE1_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 +#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 + +/* enable PCIE clock */ +#define CONFIG_SYS_SCCR_PCIEXP1CM 1 + +#define CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCIE + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 + +/* + * TSEC + */ +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) + +/* + * TSEC ethernet configuration + */ +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1 +#define CONFIG_TSEC1_NAME "eTSEC0" +#define TSEC1_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC1_FLAGS 0 + +/* Options are: eTSEC[0-1] */ +#define CONFIG_ETHPRIME "eTSEC0" + +/* + * Environment + */ +#if 1 +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE +#else +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * Command line configuration. + */ +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +#undef CONFIG_ZERO_BOOTDELAY_CHECK /* ignore keypress on bootdelay==0 */ + +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ + HID0_ENABLE_INSTRUCTION_CACHE | \ + HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) +#define CONFIG_SYS_HID2 HID2_HBE + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U + +/* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ + BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ + BATL_CACHEINHIBIT | \ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U + +/* + * Environment Configuration + */ + +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ + +#define CONFIG_HOSTNAME hrcon +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" + +#define CONFIG_PREBOOT /* enable preboot variable */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS1\0" \ + "u-boot=u-boot.bin\0" \ + "kernel_addr=1000000\0" \ + "fdt_addr=C00000\0" \ + "fdtfile=hrcon.dtb\0" \ + "load=tftp ${loadaddr} ${u-boot}\0" \ + "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ + " +${filesize};cp.b ${fileaddr} " \ + __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ + "upd=run load update\0" \ + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp ${kernel_addr} $bootfile;" \ + "tftp ${fdt_addr} $fdtfile;" \ + "bootm ${kernel_addr} - ${fdt_addr}" + +#define CONFIG_MMCBOOTCOMMAND \ + "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "ext2load mmc 0:2 ${kernel_addr} $bootfile;" \ + "ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \ + "bootm ${kernel_addr} - ${fdt_addr}" + +#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND + + +#endif /* __CONFIG_H */ diff --git a/include/gdsys_fpga.h b/include/gdsys_fpga.h index f8d8322d59..69d248f170 100644 --- a/include/gdsys_fpga.h +++ b/include/gdsys_fpga.h @@ -197,6 +197,69 @@ struct ihs_fpga { }; #endif +#ifdef CONFIG_STRIDER_CPU +struct ihs_fpga { + u16 reflection_low; /* 0x0000 */ + u16 versions; /* 0x0002 */ + u16 fpga_version; /* 0x0004 */ + u16 fpga_features; /* 0x0006 */ + u16 reserved_0[1]; /* 0x0008 */ + u16 top_interrupt; /* 0x000a */ + u16 reserved_1[3]; /* 0x000c */ + u16 extended_control; /* 0x0012 */ + struct ihs_gpio gpio; /* 0x0014 */ + u16 mpc3w_control; /* 0x001a */ + u16 reserved_2[2]; /* 0x001c */ + struct ihs_io_ep ep; /* 0x0020 */ + u16 reserved_3[9]; /* 0x002e */ + u16 mc_int; /* 0x0040 */ + u16 mc_int_en; /* 0x0042 */ + u16 mc_status; /* 0x0044 */ + u16 mc_control; /* 0x0046 */ + u16 mc_tx_data; /* 0x0048 */ + u16 mc_tx_address; /* 0x004a */ + u16 mc_tx_cmd; /* 0x004c */ + u16 mc_res; /* 0x004e */ + u16 mc_rx_cmd_status; /* 0x0050 */ + u16 mc_rx_data; /* 0x0052 */ + u16 reserved_4[62]; /* 0x0054 */ + struct ihs_i2c i2c0; /* 0x00d0 */ +}; +#endif + +#ifdef CONFIG_STRIDER_CON +struct ihs_fpga { + u16 reflection_low; /* 0x0000 */ + u16 versions; /* 0x0002 */ + u16 fpga_version; /* 0x0004 */ + u16 fpga_features; /* 0x0006 */ + u16 reserved_0[1]; /* 0x0008 */ + u16 top_interrupt; /* 0x000a */ + u16 reserved_1[4]; /* 0x000c */ + struct ihs_gpio gpio; /* 0x0014 */ + u16 mpc3w_control; /* 0x001a */ + u16 reserved_2[2]; /* 0x001c */ + struct ihs_io_ep ep; /* 0x0020 */ + u16 reserved_3[9]; /* 0x002e */ + struct ihs_i2c i2c0; /* 0x0040 */ + u16 reserved_4[10]; /* 0x004c */ + u16 mc_int; /* 0x0060 */ + u16 mc_int_en; /* 0x0062 */ + u16 mc_status; /* 0x0064 */ + u16 mc_control; /* 0x0066 */ + u16 mc_tx_data; /* 0x0068 */ + u16 mc_tx_address; /* 0x006a */ + u16 mc_tx_cmd; /* 0x006c */ + u16 mc_res; /* 0x006e */ + u16 mc_rx_cmd_status; /* 0x0070 */ + u16 mc_rx_data; /* 0x0072 */ + u16 reserved_5[70]; /* 0x0074 */ + struct ihs_osd osd; /* 0x0100 */ + u16 reserved_6[889]; /* 0x010e */ + u16 videomem[31736]; /* 0x0800 */ +}; +#endif + #ifdef CONFIG_DLVISION_10G struct ihs_fpga { u16 reflection_low; /* 0x0000 */