From: Padmarao Begari Date: Fri, 15 Jan 2021 02:50:41 +0000 (+0530) Subject: doc: board: Add Microchip MPFS Icicle Kit doc X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=9e550e18305fb31af83bfb72d16e86d8c054fb65;p=u-boot.git doc: board: Add Microchip MPFS Icicle Kit doc This doc describes the procedure to build, flash and boot Linux using U-boot on Microchip MPFS Icicle Kit. Signed-off-by: Padmarao Begari Reviewed-by: Anup Patel Reviewed-by: Bin Meng --- diff --git a/doc/board/index.rst b/doc/board/index.rst index 915f1be8a5..08c167b6b5 100644 --- a/doc/board/index.rst +++ b/doc/board/index.rst @@ -17,6 +17,7 @@ Board-specific doc google/index intel/index kontron/index + microchip/index renesas/index rockchip/index sifive/index diff --git a/doc/board/microchip/index.rst b/doc/board/microchip/index.rst new file mode 100644 index 0000000000..affc5a9e01 --- /dev/null +++ b/doc/board/microchip/index.rst @@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Microchip +========= + +.. toctree:: + :maxdepth: 2 + + mpfs_icicle diff --git a/doc/board/microchip/mpfs_icicle.rst b/doc/board/microchip/mpfs_icicle.rst new file mode 100644 index 0000000000..7489761501 --- /dev/null +++ b/doc/board/microchip/mpfs_icicle.rst @@ -0,0 +1,810 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Microchip PolarFire SoC Icicle Kit +================================== + +RISC-V PolarFire SoC +-------------------- +The PolarFire SoC is the 4+1 64-bit RISC-V SoC from Microchip. + +The Icicle Kit development platform is based on PolarFire SoC and capable +of running Linux. + +Mainline support +---------------- +The support for following drivers are already enabled: + +1. NS16550 UART Driver. +2. Microchip Clock Driver. +3. Cadence MACB ethernet driver for networking support. +4. Cadence MMC Driver for eMMC/SD support. + +Booting from eMMC using HSS +--------------------------- + +Building U-Boot +--------------- + +1. Add the RISC-V toolchain to your PATH. +2. Setup ARCH & cross compilation environment variable: + +.. code-block:: none + + export CROSS_COMPILE= + +3. make microchip_mpfs_icicle_defconfig +4. make + +Flashing +-------- + +The current U-Boot port is supported in S-mode only and loaded from DRAM. + +A prior stage M-mode firmware/bootloader (e.g HSS with OpenSBI) is required to +boot the u-boot.bin in S-mode. + +Currently, the u-boot.bin is used as a payload of the HSS firmware (Microchip +boot-flow) and OpenSBI generic platform fw_payload.bin (with u-boot.bin embedded) +as HSS payload (Custom boot-flow) + +Microchip boot-flow +------------------- +HSS with OpenSBI (M-Mode) -> U-Boot (S-Mode) -> Linux (S-Mode) + +Build the HSS (Hart Software Services) - Microchip boot-flow +------------------------------------------------------------ +(Note: HSS git repo is at https://github.com/polarfire-soc/hart-software-services) + +1. Configure + +.. code-block:: none + + make BOARD=icicle-kit-es config + +Alternatively, copy the default config for Microchip boot-flow. + +.. code-block:: none + + cp boards/icicle-kit-es/def_config .config + +2. make BOARD=icicle-kit-es +3. In the Default subdirectory, the standard build will create hss.elf and + various binary formats (hss.hex and hss.bin). + +The FPGA design will use the hss.hex or hss.bin. + +FPGA design with HSS programming file +------------------------------------- +https://github.com/polarfire-soc/polarfire-soc-documentation/blob/master/boards/mpfs-icicle-kit-es/updating-icicle-kit/updating-icicle-kit-design-and-linux.md + +The HSS firmware runs from the PolarFire SoC eNVM on reset. + +Creating the HSS payload - Microchip boot-flow +---------------------------------------------- +1. You will be creating a payload from `u-boot-dtb.bin`. + Copy this file to the HSS/tools/hss-payload-generator/test directory. +2. Go to hss-payload-generator source directory. + +.. code-block:: none + + cd hart-software-services/tools/hss-payload-generator + +3. Edit test/uboot.yaml file for hart entry points and correct name of the binary file. + + hart-entry-points: {u54_1: '0x80200000', u54_2: '0x80200000', u54_3: '0x80200000', u54_4: '0x80200000'} + + payloads: + test/u-boot-dtb.bin: {exec-addr: '0x80200000', owner-hart: u54_1, secondary-hart: u54_2, secondary-hart: u54_3, secondary-hart: u54_4, priv-mode: prv_s} + +4. Generate payload + +.. code-block:: none + + ./hss-payload-generator -c test/uboot.yaml payload.bin + +Once the payload binary is generated, it should be copied to the eMMC. + +Please refer to HSS documenation to build the HSS firmware for payload. +(Note: HSS git repo is at https://github.com/polarfire-soc/hart-software-services/blob/master/tools/hss-payload-generator/README.md) + +Custom boot-flow +---------------- +HSS without OpenSBI (M-Mode) -> OpenSBI (M-Mode) -> U-Boot (S-Mode) -> Linux (S-Mode) + +Build OpenSBI +------------- + +1. Get the OpenSBI source + +.. code-block:: none + + git clone https://github.com/riscv/opensbi.git + cd opensbi + +2. Build + +.. code-block:: none + + make PLATFORM=generic FW_PAYLOAD_PATH=/u-boot.bin + FW_FDT_PATH=/arch/riscv/dts/microchip-mpfs-icicle-kit-.dtb + +3. Output "fw_payload.bin" file available at + "/build/platform/generic/firmware/fw_payload.bin" + +Build the HSS (Hart Software Services)- Custom boot-flow +-------------------------------------------------------- +(Note: HSS git repo is at https://github.com/polarfire-soc/hart-software-services) + +1. Configure + +.. code-block:: none + + make BOARD=icicle-kit-es config + +Alternatively, copy the default custom config for Custom boot-flow. + +.. code-block:: none + + cp boards/icicle-kit-es/def_config_custom .config + +2. make BOARD=icicle-kit-es +3. In the Default subdirectory, the standard build will create hss.elf and + various binary formats (hss.hex and hss.bin). + +The FPGA design will use the hss.hex or hss.bin. + +Creating the HSS payload - Custom boot-flow +------------------------------------------- +1. You will be creating a payload from `fw_payload.bin`. + Copy this file to the HSS/tools/hss-payload-generator/test directory. +2. Go to hss-payload-generator source directory. + +.. code-block:: none + + cd hart-software-services/tools/hss-payload-generator + +3. Edit test/uboot.yaml file for hart entry points and correct name of the binary file. + + hart-entry-points: {u54_1: '0x80000000', u54_2: '0x80000000', u54_3: '0x80000000', u54_4: '0x80000000'} + + payloads: + test/fw_payload.bin: {exec-addr: '0x80000000', owner-hart: u54_1, secondary-hart: u54_2, secondary-hart: u54_3, secondary-hart: u54_4, priv-mode: prv_m} + +4. Generate payload + +.. code-block:: none + + ./hss-payload-generator -c test/uboot.yaml payload.bin + +Once the payload binary is generated, it should be copied to the eMMC. + +Please refer to HSS documenation to build the HSS firmware for payload. +(Note: HSS git repo is at https://github.com/polarfire-soc/hart-software-services/blob/master/tools/hss-payload-generator/README.md +and also refer the HSS payload generator at https://github.com/polarfire-soc/polarfire-soc-documentation/blob/master/software-development/hss-payloads.md) + +eMMC +---- +Program eMMC with payload binary is explained in the PolarFire SoC documentation. +(Note: PolarFire SoC Documentation git repo is at https://github.com/polarfire-soc/polarfire-soc-documentation/blob/master/boards/mpfs-icicle-kit-es/updating-icicle-kit/updating-icicle-kit-design-and-linux.md#eMMC) + +Once the payload image is copied to the eMMC, press CTRL+C in the HSS command +line interface, then type 'boot' and enter to boot the newly copied image. + +.. code-block:: none + + sudo dd if= of=/dev/sdX bs=512 + +GUID type +--------- +The HSS always picks up HSS payload from a GPT partition with +GIUD type "21686148-6449-6E6F-744E-656564454649" or sector '0' of the eMMC if no +GPT partition. + +Booting +------- +You should see the U-Boot prompt on UART0. + +Sample boot log from MPFS Icicle Kit +------------------------------------ + +.. code-block:: none + + U-Boot 2021.01-00314-g7303332537-dirty (Jan 14 2021 - 10:09:43 +0530) + + CPU: rv64imafdc + Model: Microchip MPFS Icicle Kit + DRAM: 1 GiB + MMC: sdhc@20008000: 0 + In: serial@20100000 + Out: serial@20100000 + Err: serial@20100000 + Net: eth0: ethernet@20112000 + Hit any key to stop autoboot: 0 + +Now you can configure your networking, tftp server and use tftp boot method to +load uImage (with initramfs). + +.. code-block:: none + + RISC-V # setenv kernel_addr_r 0x80200000 + RISC-V # setenv fdt_addr_r 0x82200000 + + RISC-V # setenv ipaddr 192.168.1.5 + RISC-V # setenv netmask 255.255.255.0 + RISC-V # setenv serverip 192.168.1.3 + RISC-V # setenv gateway 192.168.1.1 + + RISC-V # tftpboot ${kernel_addr_r} uImage + ethernet@20112000: PHY present at 9 + ethernet@20112000: Starting autonegotiation... + ethernet@20112000: Autonegotiation complete + ethernet@20112000: link up, 1000Mbps full-duplex (lpa: 0x7800) + Using ethernet@20112000 device + TFTP from server 192.168.1.3; our IP address is 192.168.1.5 + Filename 'uImage'. + Load address: 0x80200000 + Loading: ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ############ + 6.4 MiB/s + done + Bytes transferred = 14482480 (dcfc30 hex) + + RISC-V # tftpboot ${fdt_addr_r} microchip-mpfs-icicle-kit.dtb + ethernet@20112000: PHY present at 9 + ethernet@20112000: Starting autonegotiation... + ethernet@20112000: Autonegotiation complete + ethernet@20112000: link up, 1000Mbps full-duplex (lpa: 0x7800) + Using ethernet@20112000 device + TFTP from server 192.168.1.3; our IP address is 192.168.1.5 + Filename 'microchip-mpfs-icicle-kit.dtb'. + Load address: 0x82200000 + Loading: # + 2.5 MiB/s + done + Bytes transferred = 10282 (282a hex) + + RISC-V # bootm ${kernel_addr_r} - ${fdt_addr_r} + ## Booting kernel from Legacy Image at 80200000 ... + Image Name: Linux + Image Type: RISC-V Linux Kernel Image (uncompressed) + Data Size: 14482416 Bytes = 13.8 MiB + Load Address: 80200000 + Entry Point: 80200000 + Verifying Checksum ... OK + ## Flattened Device Tree blob at 82200000 + Booting using the fdt blob at 0x82200000 + Loading Kernel Image + Using Device Tree in place at 000000008fffa000, end 000000008ffff829 ... OK + + Starting kernel ... + + [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000 + [ 0.000000] Linux version 5.6.17 (padmarao@padmarao-VirtualBox) (gcc version 7.2.0 (GCC)) #2 SMP Tue Jun 16 21:27:50 IST 2020 + [ 0.000000] initrd not found or empty - disabling initrd + [ 0.000000] Zone ranges: + [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff] + [ 0.000000] Normal empty + [ 0.000000] Movable zone start for each node + [ 0.000000] Early memory node ranges + [ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff] + [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff] + [ 0.000000] software IO TLB: mapped [mem 0xbb1f5000-0xbf1f5000] (64MB) + [ 0.000000] elf_hwcap is 0x112d + [ 0.000000] percpu: Embedded 14 pages/cpu s24856 r0 d32488 u57344 + [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055 + [ 0.000000] Kernel command line: console=ttyS0,115200n8 + [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) + [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) + [ 0.000000] Sorting __ex_table... + [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off + [ 0.000000] Memory: 950308K/1046528K available (3289K kernel code, 212K rwdata, 900K rodata, 9476K init, 250K bss, 96220K reserved, 0K cma-reserved) + [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 + [ 0.000000] rcu: Hierarchical RCU implementation. + [ 0.000000] rcu: RCU event tracing is enabled. + [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. + [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. + [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 + [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0 + [ 0.000000] plic: mapped 186 interrupts with 4 handlers for 9 contexts. + [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1] + [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns + [ 0.000015] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns + [ 0.000311] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000) + [ 0.000349] pid_max: default: 32768 minimum: 301 + [ 0.000846] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) + [ 0.000964] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) + [ 0.005630] rcu: Hierarchical SRCU implementation. + [ 0.006901] smp: Bringing up secondary CPUs ... + [ 0.012545] smp: Brought up 1 node, 4 CPUs + [ 0.014431] devtmpfs: initialized + [ 0.020526] random: get_random_bytes called from setup_net+0x36/0x192 with crng_init=0 + [ 0.020928] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns + [ 0.020999] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) + [ 0.022768] NET: Registered protocol family 16 + [ 0.035478] microchip-pfsoc-clkcfg 20002000.clkcfg: Registered PFSOC core clocks + [ 0.048429] SCSI subsystem initialized + [ 0.049694] pps_core: LinuxPPS API ver. 1 registered + [ 0.049719] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti + [ 0.049780] PTP clock support registered + [ 0.051781] clocksource: Switched to clocksource riscv_clocksource + [ 0.055326] NET: Registered protocol family 2 + [ 0.056922] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) + [ 0.057053] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) + [ 0.057648] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) + [ 0.058579] TCP: Hash tables configured (established 8192 bind 8192) + [ 0.059648] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) + [ 0.059837] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) + [ 0.060707] NET: Registered protocol family 1 + [ 0.266229] workingset: timestamp_bits=62 max_order=18 bucket_order=0 + [ 0.287107] io scheduler mq-deadline registered + [ 0.287140] io scheduler kyber registered + [ 0.429601] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled + [ 0.433979] printk: console [ttyS0] disabled + [ 0.434154] 20000000.serial: ttyS0 at MMIO 0x20000000 (irq = 18, base_baud = 9375000) is a 16550A + [ 0.928039] printk: console [ttyS0] enabled + [ 0.939804] libphy: Fixed MDIO Bus: probed + [ 0.948702] libphy: MACB_mii_bus: probed + [ 0.993698] macb 20112000.ethernet eth0: Cadence GEM rev 0x0107010c at 0x20112000 irq 21 (56:34:12:00:fc:00) + [ 1.006751] mousedev: PS/2 mouse device common for all mice + [ 1.013803] i2c /dev entries driver + [ 1.019451] sdhci: Secure Digital Host Controller Interface driver + [ 1.027242] sdhci: Copyright(c) Pierre Ossman + [ 1.032731] sdhci-pltfm: SDHCI platform and OF driver helper + [ 1.091826] mmc0: SDHCI controller on 20008000.sdhc [20008000.sdhc] using ADMA 64-bit + [ 1.102738] NET: Registered protocol family 17 + [ 1.170326] Freeing unused kernel memory: 9476K + [ 1.176067] This architecture does not have kernel memory protection. + [ 1.184157] Run /init as init process + Starting logging: OK + Starting mdev... + /etc/init.d/S10mdev: line 21: can't create /proc/sys/kernel/hotplug: nonexiste[ 1.331981] mmc0: mmc_select_hs200 failed, error -74 + nt directory + [ 1.355011] mmc0: new MMC card at address 0001 + [ 1.363981] mmcblk0: mmc0:0001 DG4008 7.28 GiB + [ 1.372248] mmcblk0boot0: mmc0:0001 DG4008 partition 1 4.00 MiB + [ 1.382292] mmcblk0boot1: mmc0:0001 DG4008 partition 2 4.00 MiB + [ 1.390265] mmcblk0rpmb: mmc0:0001 DG4008 partition 3 4.00 MiB, chardev (251:0) + [ 1.425234] GPT:Primary header thinks Alt. header is not at the end of the disk. + [ 1.434656] GPT:2255809 != 15273599 + [ 1.439038] GPT:Alternate GPT header not at the end of the disk. + [ 1.446671] GPT:2255809 != 15273599 + [ 1.451048] GPT: Use GNU Parted to correct GPT errors. + [ 1.457755] mmcblk0: p1 p2 p3 + sort: /sys/devices/platform/Fixed: No such file or directory + modprobe: can't change directory to '/lib/modules': No such file or directory + Initializing random number generator... [ 2.830198] random: dd: uninitialized urandom read (512 bytes read) + done. + Starting network... + [ 3.061867] macb 20112000.ethernet eth0: PHY [20112000.ethernet-ffffffff:09] driver [Vitesse VSC8662] (irq=POLL) + [ 3.074674] macb 20112000.ethernet eth0: configuring for phy/sgmii link mode + [ 3.084263] pps pps0: new PPS source ptp0 + [ 3.089710] macb 20112000.ethernet: gem-ptp-timer ptp clock registered. + udhcpc (v1.24.2) started + Sending discover... + Sending discover... + [ 6.380169] macb 20112000.ethernet eth0: Link is Up - 1Gbps/Full - flow control tx + Sending discover... + Sending select for 192.168.1.2... + Lease of 192.168.1.2 obtained, lease time 86400 + deleting routers + adding dns 192.168.1.1 + Starting dropbear sshd: [ 11.385619] random: dropbear: uninitialized urandom read (32 bytes read) + OK + + Welcome to Buildroot + buildroot login: root + Password: + # + +Booting U-Boot and Linux from eMMC +---------------------------------- + +FPGA design with HSS programming file and Linux Image +----------------------------------------------------- +https://github.com/polarfire-soc/polarfire-soc-documentation/blob/master/boards/mpfs-icicle-kit-es/updating-icicle-kit/updating-icicle-kit-design-and-linux.md + +The HSS firmware runs from the PolarFire SoC eNVM on reset. + +eMMC +---- +Program eMMC with payload binary and Linux image is explained in the +PolarFire SoC documentation. +The payload binary should be copied to partition 2 of the eMMC. + +(Note: PolarFire SoC Documentation git repo is at https://github.com/polarfire-soc/polarfire-soc-documentation/blob/master/boards/mpfs-icicle-kit-es/updating-icicle-kit/updating-icicle-kit-design-and-linux.md#eMMC) + +Once the Linux image and payload binary is copied to the eMMC, press CTRL+C +in the HSS command line interface, then type 'boot' and enter to boot the newly +copied payload and Linux image. + +.. code-block:: none + + zcat .wic.gz | sudo dd of=/dev/sdX bs=4096 iflag=fullblock oflag=direct conv=fsync status=progress + + sudo dd if= of=/dev/sdX2 bs=512 + +You should see the U-Boot prompt on UART0. + +GUID type +--------- +The HSS always picks up the HSS payload from a GPT partition with +GIUD type "21686148-6449-6E6F-744E-656564454649" or sector '0' of the eMMC if no +GPT partition. + +Sample boot log from MPFS Icicle Kit +------------------------------------ + +.. code-block:: none + + U-Boot 2021.01-00314-g7303332537-dirty (Jan 14 2021 - 10:09:43 +0530) + + CPU: rv64imafdc + Model: Microchip MPFS Icicle Kit + DRAM: 1 GiB + MMC: sdhc@20008000: 0 + In: serial@20100000 + Out: serial@20100000 + Err: serial@20100000 + Net: eth0: ethernet@20112000 + Hit any key to stop autoboot: 0 + + RISC-V # mmc info + Device: sdhc@20008000 + Manufacturer ID: 45 + OEM: 100 + Name: DG400 + Bus Speed: 52000000 + Mode: MMC High Speed (52MHz) + Rd Block Len: 512 + MMC version 5.1 + High Capacity: Yes + Capacity: 7.3 GiB + Bus Width: 4-bit + Erase Group Size: 512 KiB + HC WP Group Size: 8 MiB + User Capacity: 7.3 GiB WRREL + Boot Capacity: 4 MiB ENH + RPMB Capacity: 4 MiB ENH + + RISC-V # mmc part + Partition Map for MMC device 0 -- Partition Type: EFI + + Part Start LBA End LBA Name + Attributes + Type GUID + Partition GUID + 1 0x00002000 0x0000b031 "boot" + attrs: 0x0000000000000004 + type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 + guid: 99ff6a94-f2e7-44dd-a7df-f3a2da106ef9 + 2 0x0000b032 0x0000f031 "primary" + attrs: 0x0000000000000000 + type: 21686148-6449-6e6f-744e-656564454649 + guid: 12006052-e64b-4423-beb0-b956ea00f1ba + 3 0x00010000 0x00226b9f "root" + attrs: 0x0000000000000000 + type: 0fc63daf-8483-4772-8e79-3d69d8477de4 + guid: dd2c5619-2272-4c3c-8dc2-e21942e17ce6 + + RISC-V # load mmc 0 ${ramdisk_addr_r} fitimage + RISC-V # bootm ${ramdisk_addr_r} + ## Loading kernel from FIT Image at 88300000 ... + Using 'conf@microchip_icicle-kit-es-a000-microchip.dtb' configuration + Trying 'kernel@1' kernel subimage + Description: Linux kernel + Type: Kernel Image + Compression: gzip compressed + Data Start: 0x883000fc + Data Size: 3574555 Bytes = 3.4 MiB + Architecture: RISC-V + OS: Linux + Load Address: 0x80200000 + Entry Point: 0x80200000 + Hash algo: sha256 + Hash value: 21f18d72cf2f0a7192220abb577ad25c77c26960052d779aa02bf55dbf0a6403 + Verifying Hash Integrity ... sha256+ OK + ## Loading fdt from FIT Image at 88300000 ... + Using 'conf@microchip_icicle-kit-es-a000-microchip.dtb' configuration + Trying 'fdt@microchip_icicle-kit-es-a000-microchip.dtb' fdt subimage + Description: Flattened Device Tree blob + Type: Flat Device Tree + Compression: uncompressed + Data Start: 0x88668d44 + Data Size: 9760 Bytes = 9.5 KiB + Architecture: RISC-V + Load Address: 0x82200000 + Hash algo: sha256 + Hash value: 5c3a9f30d41b6b8e53b47916e1f339b3a4d454006554d1f7e1f552ed62409f4b + Verifying Hash Integrity ... sha256+ OK + Loading fdt from 0x88668d48 to 0x82200000 + Booting using the fdt blob at 0x82200000 + Uncompressing Kernel Image + Loading Device Tree to 000000008fffa000, end 000000008ffff61f ... OK + + Starting kernel ... + + [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000 + [ 0.000000] Linux version 5.6.16 (oe-user@oe-host) (gcc version 9.3.0 (GCC)) #1 SMP Fri Oct 9 11:49:47 UTC 2020 + [ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '') + [ 0.000000] printk: bootconsole [sbi0] enabled + [ 0.000000] Zone ranges: + [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000bfffffff] + [ 0.000000] Normal empty + [ 0.000000] Movable zone start for each node + [ 0.000000] Early memory node ranges + [ 0.000000] node 0: [mem 0x0000000080200000-0x00000000bfffffff] + [ 0.000000] Zeroed struct page in unavailable ranges: 512 pages + [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000bfffffff] + [ 0.000000] software IO TLB: mapped [mem 0xb9e00000-0xbde00000] (64MB) + [ 0.000000] CPU with hartid=0 is not available + [ 0.000000] CPU with hartid=0 is not available + [ 0.000000] elf_hwcap is 0x112d + [ 0.000000] percpu: Embedded 17 pages/cpu s29784 r8192 d31656 u69632 + [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258055 + [ 0.000000] Kernel command line: earlycon=sbi root=/dev/mmcblk0p3 rootwait console=ttyS0,115200n8 uio_pdrv_genirq.of_id=generic-uio + [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) + [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) + [ 0.000000] Sorting __ex_table... + [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off + [ 0.000000] Memory: 941440K/1046528K available (4118K kernel code, 280K rwdata, 1687K rodata, 169K init, 273K bss, 105088K reserved, 0K cma-reserved) + [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 + [ 0.000000] rcu: Hierarchical RCU implementation. + [ 0.000000] rcu: RCU event tracing is enabled. + [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=5 to nr_cpu_ids=4. + [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. + [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 + [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0 + [ 0.000000] plic: mapped 53 interrupts with 4 handlers for 9 contexts. + [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1] + [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns + [ 0.000015] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns + [ 0.008679] Console: colour dummy device 80x25 + [ 0.013112] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000) + [ 0.023368] pid_max: default: 32768 minimum: 301 + [ 0.028314] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) + [ 0.035766] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) + [ 0.047099] rcu: Hierarchical SRCU implementation. + [ 0.052813] smp: Bringing up secondary CPUs ... + [ 0.061581] smp: Brought up 1 node, 4 CPUs + [ 0.067069] devtmpfs: initialized + [ 0.073621] random: get_random_u32 called from bucket_table_alloc.isra.0+0x4e/0x150 with crng_init=0 + [ 0.074409] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns + [ 0.093399] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) + [ 0.101879] NET: Registered protocol family 16 + [ 0.110336] microchip-pfsoc-clkcfg 20002000.clkcfg: Registered PFSOC core clocks + [ 0.132717] usbcore: registered new interface driver usbfs + [ 0.138225] usbcore: registered new interface driver hub + [ 0.143813] usbcore: registered new device driver usb + [ 0.148939] pps_core: LinuxPPS API ver. 1 registered + [ 0.153929] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti + [ 0.163071] PTP clock support registered + [ 0.168521] clocksource: Switched to clocksource riscv_clocksource + [ 0.174927] VFS: Disk quotas dquot_6.6.0 + [ 0.179016] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) + [ 0.205536] NET: Registered protocol family 2 + [ 0.210944] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) + [ 0.219393] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) + [ 0.227497] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) + [ 0.235440] TCP: Hash tables configured (established 8192 bind 8192) + [ 0.242537] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) + [ 0.249285] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) + [ 0.256690] NET: Registered protocol family 1 + [ 0.262585] workingset: timestamp_bits=62 max_order=18 bucket_order=0 + [ 0.281036] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) + [ 0.288481] io scheduler mq-deadline registered + [ 0.292983] io scheduler kyber registered + [ 0.298895] microsemi,mss-gpio 20122000.gpio: Microsemi MSS GPIO registered 32 GPIOs + [ 0.453723] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled + [ 0.462911] printk: console [ttyS0] disabled + [ 0.467216] 20100000.serial: ttyS0 at MMIO 0x20100000 (irq = 12, base_baud = 9375000) is a 16550A + [ 0.476201] printk: console [ttyS0] enabled + [ 0.476201] printk: console [ttyS0] enabled + [ 0.484576] printk: bootconsole [sbi0] disabled + [ 0.484576] printk: bootconsole [sbi0] disabled + [ 0.494920] 20102000.serial: ttyS1 at MMIO 0x20102000 (irq = 13, base_baud = 9375000) is a 16550A + [ 0.505068] 20104000.serial: ttyS2 at MMIO 0x20104000 (irq = 14, base_baud = 9375000) is a 16550A + [ 0.533336] loop: module loaded + [ 0.572284] Rounding down aligned max_sectors from 4294967295 to 4294967288 + [ 0.580000] db_root: cannot open: /etc/target + [ 0.585413] libphy: Fixed MDIO Bus: probed + [ 0.591526] libphy: MACB_mii_bus: probed + [ 0.598060] macb 20112000.ethernet eth0: Cadence GEM rev 0x0107010c at 0x20112000 irq 17 (56:34:12:00:fc:00) + [ 0.608352] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver + [ 0.615001] ehci-platform: EHCI generic platform driver + [ 0.620446] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver + [ 0.626632] ohci-platform: OHCI generic platform driver + [ 0.632326] usbcore: registered new interface driver cdc_acm + [ 0.637996] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters + [ 0.646459] i2c /dev entries driver + [ 0.650852] microsemi-mss-i2c 2010b000.i2c: Microsemi I2C Probe Complete + [ 0.658010] sdhci: Secure Digital Host Controller Interface driver + [ 0.664326] sdhci: Copyright(c) Pierre Ossman + [ 0.668754] sdhci-pltfm: SDHCI platform and OF driver helper + [ 0.706845] mmc0: SDHCI controller on 20008000.sdhc [20008000.sdhc] using ADMA 64-bit + [ 0.715052] usbcore: registered new interface driver usbhid + [ 0.720722] usbhid: USB HID core driver + [ 0.725174] pac193x 0-0010: Chip revision: 0x03 + [ 0.733339] pac193x 0-0010: :pac193x_prep_iio_channels: Channel 0 active + [ 0.740127] pac193x 0-0010: :pac193x_prep_iio_channels: Channel 1 active + [ 0.746881] pac193x 0-0010: :pac193x_prep_iio_channels: Channel 2 active + [ 0.753686] pac193x 0-0010: :pac193x_prep_iio_channels: Channel 3 active + [ 0.760495] pac193x 0-0010: :pac193x_prep_iio_channels: Active chip channels: 25 + [ 0.778006] NET: Registered protocol family 10 + [ 0.784929] Segment Routing with IPv6 + [ 0.788875] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver + [ 0.795743] NET: Registered protocol family 17 + [ 0.801191] hctosys: unable to open rtc device (rtc0) + [ 0.807774] Waiting for root device /dev/mmcblk0p3... + [ 0.858506] mmc0: mmc_select_hs200 failed, error -74 + [ 0.865764] mmc0: new MMC card at address 0001 + [ 0.872564] mmcblk0: mmc0:0001 DG4008 7.28 GiB + [ 0.878777] mmcblk0boot0: mmc0:0001 DG4008 partition 1 4.00 MiB + [ 0.886182] mmcblk0boot1: mmc0:0001 DG4008 partition 2 4.00 MiB + [ 0.892633] mmcblk0rpmb: mmc0:0001 DG4008 partition 3 4.00 MiB, chardev (247:0) + [ 0.919029] GPT:Primary header thinks Alt. header is not at the end of the disk. + [ 0.926448] GPT:2255841 != 15273599 + [ 0.930019] GPT:Alternate GPT header not at the end of the disk. + [ 0.936029] GPT:2255841 != 15273599 + [ 0.939583] GPT: Use GNU Parted to correct GPT errors. + [ 0.944800] mmcblk0: p1 p2 p3 + [ 0.966696] EXT4-fs (mmcblk0p3): INFO: recovery required on readonly filesystem + [ 0.974105] EXT4-fs (mmcblk0p3): write access will be enabled during recovery + [ 1.052362] random: fast init done + [ 1.057961] EXT4-fs (mmcblk0p3): recovery complete + [ 1.065734] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) + [ 1.074002] VFS: Mounted root (ext4 filesystem) readonly on device 179:3. + [ 1.081654] Freeing unused kernel memory: 168K + [ 1.086108] This architecture does not have kernel memory protection. + [ 1.092629] Run /sbin/init as init process + [ 1.702217] systemd[1]: System time before build time, advancing clock. + [ 1.754192] systemd[1]: systemd 244.3+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) + [ 1.776361] systemd[1]: Detected architecture riscv64. + + Welcome to OpenEmbedded nodistro.0! + + [ 1.829651] systemd[1]: Set hostname to . + [ 2.648597] random: systemd: uninitialized urandom read (16 bytes read) + [ 2.657485] systemd[1]: Created slice system-getty.slice. + [ OK ] Created slice system-getty.slice. + [ 2.698779] random: systemd: uninitialized urandom read (16 bytes read) + [ 2.706317] systemd[1]: Created slice system-serial\x2dgetty.slice. + [ OK ] Created slice system-serial\x2dgetty.slice. + [ 2.748716] random: systemd: uninitialized urandom read (16 bytes read) + [ 2.756098] systemd[1]: Created slice User and Session Slice. + [ OK ] Created slice User and Session Slice. + [ 2.789065] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. + [ OK ] Started Dispatch Password …ts to Console Directory Watch. + [ 2.828974] systemd[1]: Started Forward Password Requests to Wall Directory Watch. + [ OK ] Started Forward Password R…uests to Wall Directory Watch. + [ 2.869009] systemd[1]: Reached target Paths. + [ OK ] Reached target Paths. + [ 2.898808] systemd[1]: Reached target Remote File Systems. + [ OK ] Reached target Remote File Systems. + [ 2.938771] systemd[1]: Reached target Slices. + [ OK ] Reached target Slices. + [ 2.968754] systemd[1]: Reached target Swap. + [ OK ] Reached target Swap. + [ 2.999283] systemd[1]: Listening on initctl Compatibility Named Pipe. + [ OK ] Listening on initctl Compatibility Named Pipe. + [ 3.060458] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. + [ 3.069826] systemd[1]: Listening on Journal Socket (/dev/log). + [ OK ] Listening on Journal Socket (/dev/log). + [ 3.109601] systemd[1]: Listening on Journal Socket. + [ OK ] Listening on Journal Socket. + [ 3.149868] systemd[1]: Listening on Network Service Netlink Socket. + [ OK ] Listening on Network Service Netlink Socket. + [ 3.189419] systemd[1]: Listening on udev Control Socket. + [ OK ] Listening on udev Control Socket. + [ 3.229179] systemd[1]: Listening on udev Kernel Socket. + [ OK ] Listening on udev Kernel Socket. + [ 3.269520] systemd[1]: Condition check resulted in Huge Pages File System being skipped. + [ 3.278477] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. + [ 3.288200] systemd[1]: Condition check resulted in Kernel Debug File System being skipped. + [ 3.302570] systemd[1]: Mounting Temporary Directory (/tmp)... + Mounting Temporary Directory (/tmp)... + [ 3.339226] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped. + [ 3.355883] systemd[1]: Starting File System Check on Root Device... + Starting File System Check on Root Device... + [ 3.407220] systemd[1]: Starting Journal Service... + Starting Journal Service... + [ 3.422441] systemd[1]: Condition check resulted in Load Kernel Modules being skipped. + [ 3.431770] systemd[1]: Condition check resulted in FUSE Control File System being skipped. + [ 3.446415] systemd[1]: Mounting Kernel Configuration File System... + Mounting Kernel Configuration File System... + [ 3.458983] systemd[1]: Starting Apply Kernel Variables... + Starting Apply Kernel Variables... + [ 3.471368] systemd[1]: Starting udev Coldplug all Devices... + Starting udev Coldplug all Devices... + [ 3.491071] systemd[1]: Mounted Temporary Directory (/tmp). + [ OK 3.498114] systemd[1]: Mounted Kernel Configuration File System. + 0m] Mounted Temporary Directory (/tmp). + [ OK ] Mounted Kernel Configuration File System. + [ 3.550853] systemd[1]: Started Apply Kernel Variables. + [ OK 3.557535] systemd[1]: Started Journal Service. + 0m] Started Apply Kernel Variables. + [ OK ] Started Journal Service. + [ OK ] Started udev Coldplug all Devices. + [ OK ] Started File System Check on Root Device. + Starting Remount Root and Kernel File Systems... + [ 8.133469] EXT4-fs (mmcblk0p3): re-mounted. Opts: (null) + [ OK ] Started Remount Root and Kernel File Systems. + Starting Flush Journal to Persistent Storage... + [ 8.215327] systemd-journald[77]: Received client request to flush runtime journal. + Starting Create Static Device Nodes in /dev... + [ OK ] Started Flush Journal to Persistent Storage. + [ OK ] Started Create Static Device Nodes in /dev. + [ OK ] Reached target Local File Systems (Pre). + Mounting /var/volatile... + Starting udev Kernel Device Manager... + [ OK ] Mounted /var/volatile. + Starting Load/Save Random Seed... + [ OK ] Reached target Local File Systems. + Starting Create Volatile Files and Directories... + [ OK ] Started udev Kernel Device Manager. + [ OK ] Started Create Volatile Files and Directories. + Starting Network Time Synchronization... + Starting Update UTMP about System Boot/Shutdown... + [ OK ] Started Update UTMP about System Boot/Shutdown. + [ OK ] Started Network Time Synchronization. + [ 11.618575] random: crng init done + [ 11.622007] random: 7 urandom warning(s) missed due to ratelimiting + [ OK ] Started Load/Save Random Seed. + [ OK ] Reached target System Initialization. + [ OK ] Started Daily Cleanup of Temporary Directories. + [ OK ] Reached target System Time Set. + [ OK ] Reached target System Time Synchronized. + [ OK ] Reached target Timers. + [ OK ] Listening on D-Bus System Message Bus Socket. + [ OK ] Listening on dropbear.socket. + [ OK ] Reached target Sockets. + [ OK ] Reached target Basic System. + [ OK ] Started D-Bus System Message Bus. + Starting IPv6 Packet Filtering Framework... + Starting IPv4 Packet Filtering Framework... + Starting Login Service... + [ OK ] Started IPv6 Packet Filtering Framework. + [ OK ] Started IPv4 Packet Filtering Framework. + [ OK ] Reached target Network (Pre). + Starting Network Service... + [ OK ] Started Login Service. + [ 12.602455] macb 20112000.ethernet eth0: PHY [20112000.ethernet-ffffffff:09] driver [Vitesse VSC8662] (irq=POLL) + [ 12.612795] macb 20112000.ethernet eth0: configuring for phy/sgmii link mode + [ 12.622153] pps pps0: new PPS source ptp0 + [ OK 12.626725] macb 20112000.ethernet: gem-ptp-timer ptp clock registered. + 0m] Started Network Service. + Starting Network Name Resolution... + [ OK ] Started Network Name Resolution. + [ OK ] Reached target Network. + [ OK ] Reached target Host and Network Name Lookups. + [ OK ] Started Collectd. + [ OK ] Started Collectd. + Starting Permit User Sessions... + [ OK ] Started Permit User Sessions. + [ OK ] Started Getty on tty1. + [ OK ] Started Serial Getty on ttyS0. + [ OK ] Reached target Login Prompts. + [ OK ] Reached target Multi-User System. + Starting Update UTMP about System Runlevel Changes... + [ OK ] Started Update UTMP about System Runlevel Changes. + + OpenEmbedded nodistro.0 icicle-kit-es ttyS0 + + icicle-kit-es login: [ 15.795564] macb 20112000.ethernet eth0: Link is Up - 1Gbps/Full - flow control tx + [ 15.803306] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready + + icicle-kit-es login: root + root@icicle-kit-es:~#