From: Ye Li <ye.li@nxp.com>
Date: Fri, 29 Oct 2021 01:46:25 +0000 (+0800)
Subject: imx8ulp: Workaround LPOSC_TRIM fuse load issue
X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=9c7fbebe5dd5d9daa9160b778432daef2a13f47f;p=u-boot.git

imx8ulp: Workaround LPOSC_TRIM fuse load issue

8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.

A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---

diff --git a/arch/arm/include/asm/arch-imx8ulp/sys_proto.h b/arch/arm/include/asm/arch-imx8ulp/sys_proto.h
index 8e2c6ed0ce..284ccafc98 100644
--- a/arch/arm/include/asm/arch-imx8ulp/sys_proto.h
+++ b/arch/arm/include/asm/arch-imx8ulp/sys_proto.h
@@ -17,4 +17,5 @@ int xrdc_config_pdac(u32 bridge, u32 index, u32 dom, u32 perm);
 int xrdc_config_pdac_openacc(u32 bridge, u32 index);
 enum boot_device get_boot_device(void);
 void set_lpav_qos(void);
+void load_lposc_fuse(void);
 #endif
diff --git a/arch/arm/mach-imx/imx8ulp/soc.c b/arch/arm/mach-imx/imx8ulp/soc.c
index d9dca21e8c..e12e28d9e7 100644
--- a/arch/arm/mach-imx/imx8ulp/soc.c
+++ b/arch/arm/mach-imx/imx8ulp/soc.c
@@ -487,6 +487,26 @@ void lpav_configure(void)
 	writel(0x003fffff, SIM_SEC_BASE_ADDR + 0x58);
 }
 
+void load_lposc_fuse(void)
+{
+	int ret;
+	u32 val = 0, val2 = 0, reg;
+
+	ret = fuse_read(25, 0, &val);
+	if (ret)
+		return; /* failed */
+
+	ret = fuse_read(25, 1, &val2);
+	if (ret)
+		return; /* failed */
+
+	/* LPOSCCTRL */
+	reg = readl(0x2802f304);
+	reg &= ~0xff;
+	reg |= (val & 0xff);
+	writel(reg, 0x2802f304);
+}
+
 void set_lpav_qos(void)
 {
 	/* Set read QoS of dcnano on LPAV NIC */
diff --git a/board/freescale/imx8ulp_evk/spl.c b/board/freescale/imx8ulp_evk/spl.c
index 42f8e262b6..c17d5eff7d 100644
--- a/board/freescale/imx8ulp_evk/spl.c
+++ b/board/freescale/imx8ulp_evk/spl.c
@@ -77,6 +77,12 @@ void spl_board_init(void)
 
 	/* After AP set iomuxc0, the i2c can't work, Need M33 to set it now */
 
+	/* Load the lposc fuse for single boot to work around ROM issue,
+	 *  The fuse depends on S400 to read.
+	 */
+	if (is_soc_rev(CHIP_REV_1_0) && get_boot_mode() == SINGLE_BOOT)
+		load_lposc_fuse();
+
 	upower_init();
 
 	power_init_board();