From: Michal Simek Date: Tue, 4 Jul 2023 12:05:13 +0000 (+0200) Subject: sysreset: Change Kconfig GPIO dependency X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=99a0532a2d09edac8d8cf59deb68e03f3275e494;p=u-boot.git sysreset: Change Kconfig GPIO dependency DM_GPIO depends on GPIO to be enabled but select will cause that DM_GPIO is selected without GPIO which ends up in compilation error: undefined reference to `dm_gpio_set_value' undefined reference to `dm_gpio_get_value' undefined reference to `dm_gpio_free' undefined reference to `gpio_request_by_name' Signed-off-by: Michal Simek [trini: Fix configs which had relied on these select's] Signed-off-by: Tom Rini --- diff --git a/configs/ge_b1x5v2_defconfig b/configs/ge_b1x5v2_defconfig index faa22f9392..b3b69a642a 100644 --- a/configs/ge_b1x5v2_defconfig +++ b/configs/ge_b1x5v2_defconfig @@ -14,6 +14,7 @@ CONFIG_ENV_SECT_SIZE=0x10000 # CONFIG_GE_RTC is not set CONFIG_MX6QDL=y CONFIG_TARGET_GE_B1X5V2=y +CONFIG_DM_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="imx6dl-b1x5v2" CONFIG_SPL_TEXT_BASE=0x00908000 CONFIG_SPL_SERIAL=y diff --git a/configs/microblaze-generic_defconfig b/configs/microblaze-generic_defconfig index 6aa1d03e5b..589da3226d 100644 --- a/configs/microblaze-generic_defconfig +++ b/configs/microblaze-generic_defconfig @@ -4,6 +4,7 @@ CONFIG_SYS_MALLOC_LEN=0xc0000 CONFIG_SYS_MALLOC_F_LEN=0x400 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000 +CONFIG_DM_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="microblaze-generic" CONFIG_SYS_PROMPT="U-Boot-mONStR> " CONFIG_SPL_SERIAL=y diff --git a/configs/qemu-ppce500_defconfig b/configs/qemu-ppce500_defconfig index 105b937efa..5f0746e4e2 100644 --- a/configs/qemu-ppce500_defconfig +++ b/configs/qemu-ppce500_defconfig @@ -1,6 +1,7 @@ CONFIG_PPC=y CONFIG_TEXT_BASE=0xf00000 CONFIG_ENV_SIZE=0x2000 +CONFIG_DM_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="qemu-ppce500" CONFIG_SYS_MONITOR_LEN=524288 CONFIG_SYS_CLK_FREQ=33000000 diff --git a/drivers/sysreset/Kconfig b/drivers/sysreset/Kconfig index 03f7fdd597..bdbe2a9536 100644 --- a/drivers/sysreset/Kconfig +++ b/drivers/sysreset/Kconfig @@ -61,14 +61,14 @@ endif config POWEROFF_GPIO bool "Enable support for GPIO poweroff driver" - select DM_GPIO + depends on DM_GPIO help Support for system poweroff using a GPIO pin. This can be used for systems having a single GPIO to trigger a system poweroff. config SYSRESET_GPIO bool "Enable support for GPIO reset driver" - select DM_GPIO + depends on DM_GPIO help Reset support via GPIO pin connected reset logic. This is used for example on Microblaze where reset logic can be controlled via GPIO