From: Michael Pratt Date: Mon, 11 Jun 2018 19:07:09 +0000 (-0600) Subject: fdt: Add device tree memory bindings X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=90c08fa038451d;p=u-boot.git fdt: Add device tree memory bindings Support a default memory bank, specified in reg, as well as board-specific memory banks in subtree board-id nodes. This allows memory information to be provided in the device tree, rather than hard-coded in, which will make it simpler to handle similar devices with different memory banks, as the board-id values or masks can be used to match devices. Signed-off-by: Michael Pratt Signed-off-by: Simon Glass Reviewed-by: Vadim Bendebury --- diff --git a/doc/device-tree-bindings/memory/memory.txt b/doc/device-tree-bindings/memory/memory.txt new file mode 100644 index 0000000000..321894e01d --- /dev/null +++ b/doc/device-tree-bindings/memory/memory.txt @@ -0,0 +1,67 @@ +* Memory binding + +The memory binding for U-Boot is as in the ePAPR with the following additions: + +Optional subnodes can be used defining the memory layout for different board +ID masks. To match a set of board ids, a board-id node may define match-mask +and match-value ints to define a mask to apply to the board id, and the value +that the result should have for the match to be considered valid. The mask +defaults to -1, meaning that the value must fully match the board id. + +If subnodes are present, then the /memory node must define these properties: + +- #address-cells: should be 1. +- #size-cells: should be 0. + +Each subnode must define + + reg - board ID or mask for this subnode + memory-banks - list of memory banks in the same format as normal + +Each subnode may optionally define: + + match-mask - A mask to apply to the board id. This must be accompanied by + match-value. + match-value - The required resulting value of the board id mask for the given + node to be considered a match. + auto-size - Indicates that the value given for a bank is the maximum size, + each bank is probed to determine its actual size, which may be + smaller + + +The board id determination is up to the vendor and is not defined by this +binding. + +Example: + +memory { + #address-cells = <1>; + #size-cells = <1>; + reg = <0x20000000 0x20000000 + 0x40000000 0x20000000 + 0x60000000 0x20000000 + 0x80000000 0x20000000>; + auto-size; + board-id@0 { + match-value = <17>; + reg = <0x20000000 0x20000000 + 0x40000000 0x20000000>; + }; + board-id@1 { + match-mask = <2>; + match-value = <2>; + reg = <0x20000000 0x20000000 + 0x40000000 0x20000000 + 0x60000000 0x20000000 + 0x80000000 0x20000000 + 0xa0000000 0x20000000 + 0xc0000000 0x20000000 + 0xe0000000 0x20000000>; + }; +}; + + +This shows a system with the following properties: +* Default of 2GB of memory, auto-sized, so could be smaller +* 3.5GB of memory (with no auto-size) if (board id & 2) is 2 +* 1GB of memory (with no auto-size) if board id is 17. diff --git a/include/asm-generic/global_data.h b/include/asm-generic/global_data.h index 2d451f8a1b..0fd4900392 100644 --- a/include/asm-generic/global_data.h +++ b/include/asm-generic/global_data.h @@ -52,6 +52,7 @@ typedef struct global_data { unsigned long env_has_init; /* Bitmask of boolean of struct env_location offsets */ int env_load_location; + unsigned long ram_base; /* Base address of RAM used by U-Boot */ unsigned long ram_top; /* Top address of RAM used by U-Boot */ unsigned long relocaddr; /* Start address of U-Boot in RAM */ phys_size_t ram_size; /* RAM size */ diff --git a/include/fdt_support.h b/include/fdt_support.h index e6c43ea983..a9a0078af6 100644 --- a/include/fdt_support.h +++ b/include/fdt_support.h @@ -283,6 +283,16 @@ int fdt_setup_simplefb_node(void *fdt, int node, u64 base_address, u32 width, int fdt_overlay_apply_verbose(void *fdt, void *fdto); +/** + * fdt_get_cells_len() - Get the length of a type of cell in top-level nodes + * + * Returns the length of the cell type in bytes (4 or 8). + * + * @blob: Pointer to device tree blob + * @nr_cells_name: Name to lookup, e.g. "#address-cells" + */ +int fdt_get_cells_len(const void *blob, char *nr_cells_name); + #endif /* ifdef CONFIG_OF_LIBFDT */ #ifdef USE_HOSTCC diff --git a/include/fdtdec.h b/include/fdtdec.h index c15b2a04a7..332105504b 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -41,6 +41,8 @@ struct fdt_memory { fdt_addr_t end; }; +struct bd_info; + #ifdef CONFIG_SPL_BUILD #define SPL_BUILD 1 #else @@ -993,6 +995,40 @@ int fdtdec_setup(void); * Called when CONFIG_OF_BOARD is defined, or if CONFIG_OF_SEPARATE is defined * and the board implements it. */ -void *board_fdt_blob_setup(void); + +/* + * Decode the size of memory + * + * RAM size is normally set in a /memory node and consists of a list of + * (base, size) cells in the 'reg' property. This information is used to + * determine the total available memory as well as the address and size + * of each bank. + * + * Optionally the memory configuration can vary depending on a board id, + * typically read from strapping resistors or an EEPROM on the board. + * + * Finally, memory size can be detected (within certain limits) by probing + * the available memory. It is safe to do so within the limits provides by + * the board's device tree information. This makes it possible to produce + * boards with different memory sizes, where the device tree specifies the + * maximum memory configuration, and the smaller memory configuration is + * probed. + * + * This function decodes that information, returning the memory base address, + * size and bank information. See the memory.txt binding for full + * documentation. + * + * @param blob Device tree blob + * @param area Name of node to check (NULL means "/memory") + * @param board_id Board ID to look up + * @param basep Returns base address of first memory bank (NULL to + * ignore) + * @param sizep Returns total memory size (NULL to ignore) + * @param bd Updated with the memory bank information (NULL to skip) + * @return 0 if OK, -ve on error + */ +int fdtdec_decode_ram_size(const void *blob, const char *area, int board_id, + phys_addr_t *basep, phys_size_t *sizep, + struct bd_info *bd); #endif diff --git a/lib/fdtdec.c b/lib/fdtdec.c index f4e8dbf699..fc92082b0b 100644 --- a/lib/fdtdec.c +++ b/lib/fdtdec.c @@ -11,6 +11,7 @@ #include #include #include +#include #include #include #include @@ -1350,4 +1351,112 @@ int fdtdec_setup(void) return fdtdec_prepare_fdt(); } +#ifdef CONFIG_NR_DRAM_BANKS +int fdtdec_decode_ram_size(const void *blob, const char *area, int board_id, + phys_addr_t *basep, phys_size_t *sizep, bd_t *bd) +{ + int addr_cells, size_cells; + const u32 *cell, *end; + u64 total_size, size, addr; + int node, child; + bool auto_size; + int bank; + int len; + + debug("%s: board_id=%d\n", __func__, board_id); + if (!area) + area = "/memory"; + node = fdt_path_offset(blob, area); + if (node < 0) { + debug("No %s node found\n", area); + return -ENOENT; + } + + cell = fdt_getprop(blob, node, "reg", &len); + if (!cell) { + debug("No reg property found\n"); + return -ENOENT; + } + + addr_cells = fdt_address_cells(blob, node); + size_cells = fdt_size_cells(blob, node); + + /* Check the board id and mask */ + for (child = fdt_first_subnode(blob, node); + child >= 0; + child = fdt_next_subnode(blob, child)) { + int match_mask, match_value; + + match_mask = fdtdec_get_int(blob, child, "match-mask", -1); + match_value = fdtdec_get_int(blob, child, "match-value", -1); + + if (match_value >= 0 && + ((board_id & match_mask) == match_value)) { + /* Found matching mask */ + debug("Found matching mask %d\n", match_mask); + node = child; + cell = fdt_getprop(blob, node, "reg", &len); + if (!cell) { + debug("No memory-banks property found\n"); + return -EINVAL; + } + break; + } + } + /* Note: if no matching subnode was found we use the parent node */ + + if (bd) { + memset(bd->bi_dram, '\0', sizeof(bd->bi_dram[0]) * + CONFIG_NR_DRAM_BANKS); + } + + auto_size = fdtdec_get_bool(blob, node, "auto-size"); + + total_size = 0; + end = cell + len / 4 - addr_cells - size_cells; + debug("cell at %p, end %p\n", cell, end); + for (bank = 0; bank < CONFIG_NR_DRAM_BANKS; bank++) { + if (cell > end) + break; + addr = 0; + if (addr_cells == 2) + addr += (u64)fdt32_to_cpu(*cell++) << 32UL; + addr += fdt32_to_cpu(*cell++); + if (bd) + bd->bi_dram[bank].start = addr; + if (basep && !bank) + *basep = (phys_addr_t)addr; + + size = 0; + if (size_cells == 2) + size += (u64)fdt32_to_cpu(*cell++) << 32UL; + size += fdt32_to_cpu(*cell++); + + if (auto_size) { + u64 new_size; + + debug("Auto-sizing %" PRIx64 ", size %" PRIx64 ": ", + addr, size); + new_size = get_ram_size((long *)(uintptr_t)addr, size); + if (new_size == size) { + debug("OK\n"); + } else { + debug("sized to %" PRIx64 "\n", new_size); + size = new_size; + } + } + + if (bd) + bd->bi_dram[bank].size = size; + total_size += size; + } + + debug("Memory size %" PRIu64 "\n", total_size); + if (sizep) + *sizep = (phys_size_t)total_size; + + return 0; +} +#endif /* CONFIG_NR_DRAM_BANKS */ + #endif /* !USE_HOSTCC */