From: Samuel Holland <samuel@sholland.org>
Date: Sun, 22 Jan 2023 23:46:21 +0000 (-0600)
Subject: sunxi: Switch to PMIC USB power supply VBUS detection
X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=7d5b17cca626a45b8e414820044831470ae1b300;p=u-boot.git

sunxi: Switch to PMIC USB power supply VBUS detection

Update boards to use the USB power supply driver, as referenced in the
device tree, instead of a virtual GPIO. This removes the need for some
DM-incompatible special cases in the GPIO driver.

The following five boards used AXP0-VBUS-DETECT in their config, but are
missing the "usb0_vbus_power-supply" property in their device tree:
 - Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
 - Cubieboard4_defconfig / sun9i-a80-cubieboard4
 - Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
 - Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
 - Yones_Toptech_BS1078_V2_defconfig /
   sun6i-a31s-yones-toptech-bs1078-v2

None of those five boards have the MUSB controller (USB OTG) enabled in
their device trees, so this change should not break anything for them.

Additionally, the following board intentionally omits the property
because VBUS is always enabled:
 - Nintendo_NES_Classic_Edition_defconfig /
   sun8i-r16-nintendo-nes-classic

The PHY driver already assumes VBUS is enabled when no detection method
is available, so again this will not cause any problems.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---

diff --git a/configs/A33-OLinuXino_defconfig b/configs/A33-OLinuXino_defconfig
index fc32a86a25..df4acaf33e 100644
--- a/configs/A33-OLinuXino_defconfig
+++ b/configs/A33-OLinuXino_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=15291
 CONFIG_DRAM_ODT_EN=y
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PB3"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:3,vmode:0"
@@ -15,5 +14,6 @@ CONFIG_VIDEO_LCD_DCLK_PHASE=0
 CONFIG_VIDEO_LCD_BL_EN="PB2"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DCDC1_VOLT=3300
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/Ainol_AW1_defconfig b/configs/Ainol_AW1_defconfig
index 9ae3893153..51f26f48b2 100644
--- a/configs/Ainol_AW1_defconfig
+++ b/configs/Ainol_AW1_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN7I=y
 CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=123
 CONFIG_USB0_VBUS_PIN="PB9"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:40000,le:87,ri:112,up:38,lo:141,hs:1,vs:1,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_POWER="PH8"
@@ -17,4 +16,5 @@ CONFIG_SPL_I2C=y
 CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/Cubieboard4_defconfig b/configs/Cubieboard4_defconfig
index 5eee23ff5e..2f93a7b77c 100644
--- a/configs/Cubieboard4_defconfig
+++ b/configs/Cubieboard4_defconfig
@@ -6,10 +6,11 @@ CONFIG_MACH_SUN9I=y
 CONFIG_DRAM_CLK=672
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH16"
 CONFIG_USB1_VBUS_PIN="PH14"
 CONFIG_USB3_VBUS_PIN="PH15"
 CONFIG_AXP_GPIO=y
 CONFIG_SYS_I2C_SUN8I_RSB=y
+CONFIG_DM_REGULATOR=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP809_POWER=y
diff --git a/configs/Cubietruck_plus_defconfig b/configs/Cubietruck_plus_defconfig
index 13f958977b..29f4df2b81 100644
--- a/configs/Cubietruck_plus_defconfig
+++ b/configs/Cubietruck_plus_defconfig
@@ -8,7 +8,6 @@ CONFIG_DRAM_ZQ=15355
 CONFIG_DRAM_ODT_EN=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH11"
 CONFIG_USB1_VBUS_PIN="PD29"
 CONFIG_USB2_VBUS_PIN="PL6"
@@ -22,6 +21,7 @@ CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
 CONFIG_PHY_REALTEK=y
 CONFIG_SUN8I_EMAC=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO3_VOLT=2500
 CONFIG_AXP_DLDO4_VOLT=3300
 CONFIG_AXP_FLDO1_VOLT=1200
diff --git a/configs/MSI_Primo81_defconfig b/configs/MSI_Primo81_defconfig
index e77b007292..d60eedb482 100644
--- a/configs/MSI_Primo81_defconfig
+++ b/configs/MSI_Primo81_defconfig
@@ -6,13 +6,13 @@ CONFIG_MACH_SUN6I=y
 CONFIG_DRAM_CLK=360
 CONFIG_DRAM_ZQ=122
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:768,y:1024,depth:18,pclk_khz:66000,le:56,ri:60,up:30,lo:36,hs:64,vs:50,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 CONFIG_VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 # CONFIG_REQUIRE_SERIAL_CONSOLE is not set
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/Merrii_A80_Optimus_defconfig b/configs/Merrii_A80_Optimus_defconfig
index b9ccfcfdcc..f0c54e2af8 100644
--- a/configs/Merrii_A80_Optimus_defconfig
+++ b/configs/Merrii_A80_Optimus_defconfig
@@ -6,10 +6,11 @@ CONFIG_MACH_SUN9I=y
 CONFIG_DRAM_CLK=672
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH3"
 CONFIG_USB1_VBUS_PIN="PH4"
 CONFIG_USB3_VBUS_PIN="PH5"
 CONFIG_AXP_GPIO=y
 CONFIG_SYS_I2C_SUN8I_RSB=y
+CONFIG_DM_REGULATOR=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP809_POWER=y
diff --git a/configs/Nintendo_NES_Classic_Edition_defconfig b/configs/Nintendo_NES_Classic_Edition_defconfig
index 18fa3779d4..3046f45012 100644
--- a/configs/Nintendo_NES_Classic_Edition_defconfig
+++ b/configs/Nintendo_NES_Classic_Edition_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A33=y
 CONFIG_DRAM_CLK=600
 CONFIG_DRAM_ZQ=15291
 CONFIG_DRAM_ODT_EN=y
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 # CONFIG_CMD_FLASH is not set
@@ -20,6 +19,7 @@ CONFIG_SYS_NAND_ONFI_DETECTION=y
 CONFIG_SYS_NAND_PAGE_SIZE=0x800
 CONFIG_SYS_NAND_OOBSIZE=0x40
 CONFIG_SYS_NAND_MAX_ECCPOS=1664
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_AXP_ELDO2_VOLT=1800
 CONFIG_CONS_INDEX=5
diff --git a/configs/Sinovoip_BPI_M3_defconfig b/configs/Sinovoip_BPI_M3_defconfig
index 5116fab52d..5642e52ec5 100644
--- a/configs/Sinovoip_BPI_M3_defconfig
+++ b/configs/Sinovoip_BPI_M3_defconfig
@@ -9,7 +9,6 @@ CONFIG_DRAM_ZQ=15355
 CONFIG_DRAM_ODT_EN=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH11"
 CONFIG_USB1_VBUS_PIN="PD24"
 CONFIG_AXP_GPIO=y
@@ -19,6 +18,7 @@ CONFIG_CONSOLE_MUX=y
 CONFIG_PHY_REALTEK=y
 CONFIG_SUN8I_EMAC=y
 CONFIG_INITIAL_USB_SCAN_DELAY=500
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DCDC5_VOLT=1200
 CONFIG_AXP_DLDO3_VOLT=3300
 CONFIG_AXP_SW_ON=y
diff --git a/configs/Wexler_TAB7200_defconfig b/configs/Wexler_TAB7200_defconfig
index 101ce57aa4..40aeb6680c 100644
--- a/configs/Wexler_TAB7200_defconfig
+++ b/configs/Wexler_TAB7200_defconfig
@@ -5,7 +5,6 @@ CONFIG_SPL=y
 CONFIG_MACH_SUN7I=y
 CONFIG_DRAM_CLK=384
 CONFIG_USB0_VBUS_PIN="PB9"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH4"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:24,pclk_khz:33000,le:45,ri:210,up:22,lo:22,hs:1,vs:1,sync:3,vmode:0"
@@ -17,6 +16,7 @@ CONFIG_SPL_I2C=y
 CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/Yones_Toptech_BD1078_defconfig b/configs/Yones_Toptech_BD1078_defconfig
index 4f2290c289..9b13659bcc 100644
--- a/configs/Yones_Toptech_BD1078_defconfig
+++ b/configs/Yones_Toptech_BD1078_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=408
 CONFIG_MMC1_PINS_PH=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=1
 CONFIG_USB0_VBUS_PIN="PB9"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:24,pclk_khz:63000,le:32,ri:287,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_DCLK_PHASE=0
@@ -21,4 +20,5 @@ CONFIG_SPL_I2C=y
 CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/Yones_Toptech_BS1078_V2_defconfig b/configs/Yones_Toptech_BS1078_V2_defconfig
index b33c825b18..de69ebe995 100644
--- a/configs/Yones_Toptech_BS1078_V2_defconfig
+++ b/configs/Yones_Toptech_BS1078_V2_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN6I=y
 CONFIG_DRAM_CLK=420
 CONFIG_DRAM_ZQ=251
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PA15"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:24,pclk_khz:70000,le:120,ri:180,up:17,lo:15,hs:20,vs:3,sync:3,vmode:0"
@@ -15,5 +14,6 @@ CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/colorfly_e708_q1_defconfig b/configs/colorfly_e708_q1_defconfig
index 89f063bdd2..07bda04966 100644
--- a/configs/colorfly_e708_q1_defconfig
+++ b/configs/colorfly_e708_q1_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN6I=y
 CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=251
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PA15"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:1280,depth:24,pclk_khz:64000,le:20,ri:34,up:1,lo:16,hs:10,vs:1,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_AXP_DLDO2_VOLT=1800
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/ga10h_v1_1_defconfig b/configs/ga10h_v1_1_defconfig
index 599eeb96b4..935071d61a 100644
--- a/configs/ga10h_v1_1_defconfig
+++ b/configs/ga10h_v1_1_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=15291
 CONFIG_DRAM_ODT_EN=y
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:52000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"
@@ -17,6 +16,7 @@ CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_EHCI_HCD=y
diff --git a/configs/gt90h_v4_defconfig b/configs/gt90h_v4_defconfig
index f5e3a7272d..205eab2929 100644
--- a/configs/gt90h_v4_defconfig
+++ b/configs/gt90h_v4_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A23=y
 CONFIG_DRAM_CLK=480
 CONFIG_DRAM_ZQ=32767
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:55000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/iNet_D978_rev2_defconfig b/configs/iNet_D978_rev2_defconfig
index e01e184307..ed6a603842 100644
--- a/configs/iNet_D978_rev2_defconfig
+++ b/configs/iNet_D978_rev2_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A33=y
 CONFIG_DRAM_CLK=456
 CONFIG_DRAM_ZQ=15291
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:120,ri:180,up:22,lo:13,hs:20,vs:3,sync:3,vmode:0"
@@ -16,6 +15,7 @@ CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 # CONFIG_REQUIRE_SERIAL_CONSOLE is not set
 CONFIG_CONS_INDEX=5
diff --git a/configs/inet86dz_defconfig b/configs/inet86dz_defconfig
index 2035a34d15..d215a8375e 100644
--- a/configs/inet86dz_defconfig
+++ b/configs/inet86dz_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A23=y
 CONFIG_DRAM_CLK=552
 CONFIG_DRAM_ZQ=63351
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/inet_q972_defconfig b/configs/inet_q972_defconfig
index 85a3b4e7cc..24ff6c0062 100644
--- a/configs/inet_q972_defconfig
+++ b/configs/inet_q972_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN6I=y
 CONFIG_DRAM_CLK=384
 CONFIG_DRAM_ZQ=251
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PA15"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:280,ri:20,up:22,lo:8,hs:20,vs:8,sync:3,vmode:0"
@@ -14,6 +13,7 @@ CONFIG_VIDEO_LCD_DCLK_PHASE=0
 CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
diff --git a/configs/polaroid_mid2407pxe03_defconfig b/configs/polaroid_mid2407pxe03_defconfig
index 023f880fa0..6ec7c83be5 100644
--- a/configs/polaroid_mid2407pxe03_defconfig
+++ b/configs/polaroid_mid2407pxe03_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A23=y
 CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=63351
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:40,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/polaroid_mid2809pxe04_defconfig b/configs/polaroid_mid2809pxe04_defconfig
index 2e9efd0f7d..1aefc50588 100644
--- a/configs/polaroid_mid2809pxe04_defconfig
+++ b/configs/polaroid_mid2809pxe04_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A23=y
 CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=63351
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:36,ri:210,up:18,lo:22,hs:10,vs:5,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/q8_a23_tablet_800x480_defconfig b/configs/q8_a23_tablet_800x480_defconfig
index 3bfc5c5700..0f8c30ec85 100644
--- a/configs/q8_a23_tablet_800x480_defconfig
+++ b/configs/q8_a23_tablet_800x480_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A23=y
 CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=63306
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:36,ri:210,up:18,lo:22,hs:10,vs:5,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/q8_a33_tablet_1024x600_defconfig b/configs/q8_a33_tablet_1024x600_defconfig
index 9166ec05ce..b3b5cc704f 100644
--- a/configs/q8_a33_tablet_1024x600_defconfig
+++ b/configs/q8_a33_tablet_1024x600_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A33=y
 CONFIG_DRAM_CLK=456
 CONFIG_DRAM_ZQ=15291
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/q8_a33_tablet_800x480_defconfig b/configs/q8_a33_tablet_800x480_defconfig
index 6114fcbc2a..37ee08fa62 100644
--- a/configs/q8_a33_tablet_800x480_defconfig
+++ b/configs/q8_a33_tablet_800x480_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A33=y
 CONFIG_DRAM_CLK=456
 CONFIG_DRAM_ZQ=15291
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:167,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y
diff --git a/configs/tbs_a711_defconfig b/configs/tbs_a711_defconfig
index b3c2e69d6c..9a70b6bee5 100644
--- a/configs/tbs_a711_defconfig
+++ b/configs/tbs_a711_defconfig
@@ -9,11 +9,11 @@ CONFIG_DRAM_ZQ=15355
 CONFIG_DRAM_ODT_EN=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH11"
 CONFIG_AXP_GPIO=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DCDC5_VOLT=1200
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y