From: Tom Rini Date: Mon, 11 Nov 2013 17:09:10 +0000 (-0500) Subject: omap730p2: Remove board X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=79c5c08d7c560aef2d5706501557b7907c2829bb;p=u-boot.git omap730p2: Remove board Signed-off-by: Tom Rini --- diff --git a/board/ti/omap730p2/Makefile b/board/ti/omap730p2/Makefile deleted file mode 100644 index 8242f3d69f..0000000000 --- a/board/ti/omap730p2/Makefile +++ /dev/null @@ -1,9 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := omap730p2.o flash.o -obj-y += lowlevel_init.o diff --git a/board/ti/omap730p2/README.omap730p2 b/board/ti/omap730p2/README.omap730p2 deleted file mode 100644 index 7c70916120..0000000000 --- a/board/ti/omap730p2/README.omap730p2 +++ /dev/null @@ -1,91 +0,0 @@ - - u-boot for the TI OMAP730 Perseus2 - - Dave Peverley, MPC-Data Limited - http://www.mpc-data.co.uk - - -Overview : - - As the OMAP730 is similar to the OMAP1610 in many ways, this port was based -on the u-boot port to the OMAP1610 Innovator. Supported features are : - - - Serial terminal support - - Onboard NOR Flash - - Ethernet via the seperate debug board - - Tested on Rev4 and Rev5 boards - - It has also been tested to work correctly when built with a 'standard' GCC -3.2.1 cross-compiler as well as Montavista Linux CEE 3.1's toolchain. - - -Hardware Configuration : - - The main dips on the P2 board should be set to 2,3,7 and 9 on with all -others off. On the debug board, dips 1 and 7 should be on with the rest off. -The serial console has been set up to run from the DB9 connector on the -P2 board at 115200 baud, 8 data bits, no stop bits, 1 parity bit. - - It should be noted that the P2 board has NOR flash that is addressable via -either CS0 or CS3. This mode can be changed via DIP9 on the P2 board. - - -Installing u-boot for the P2 : - - You can simply build u-boot for the Perseus by following the instructions -in the main readme file. The target configuration is "omap730p2_config". -Once u-boot has been built, you should strip the executable so it can be -loaded via CCS (which cant cope with the symbols in the ELF binary) : - $ cp u-boot u-boot.out - $ arm-linux-strip u-boot.out - - The method we've used for installing u-boot the first time on a P2 is -as follows : - -1) Configure TI Code Composer Studio to connect to the P2 board via JTAG - as described in the Users Guide. - -2) Set up the P2 to boot from CS3, and connect with CCS. Reset the CPU - and run the "init_mmu" GEL script. - -3) Use the "Load Program" option to send the u-boot.out file to the P2 and - run. - - At this point, u-boot should run and you will see the boot menu on your -serial terminal. You can then load the u-boot image to memory : - - # loadb 0x10000000 - - Send the "u-boot.bin" binary via the serial using Kermit. Once loaded -you can self-flash u-boot : - - # protect off 1:0 - # erase 1:0 - # cp.b 0x10000000 0x0 0x20000 - - You should now be able to reset the board and run u-boot from flash. - - -Alternative flash option : - - Sometimes, if you've been silly, you can get the board into a state where -whats in flash has upset the board so much that you can no longer connect -to the P2 via JTAG. However, you can set DIP9 to off to swap the boot mode -of the P2 so that you boot from RAM instead of NOR flash. This moves NOR -flash up to 0x0C000000. You can build a special version of u-boot to -utilise this by the following config : - - $ make omap730p2_cs0boot_config - - If you load this up via CCS it will detect flash at its alternate location -and allow you to programme your u-boot image (which, remember must be built -for CS3 boot!) Once you do this, you can revert to CS3 boot and it will work -fine again. - - -Errata : - -1) It's been observed that sometimes the tftp transfer of kernels to the - board can have checksum errors or stall. This appears to be an issue - with the lan91c96.c driver, and can normally be worked around by - resetting the board and trying again. diff --git a/board/ti/omap730p2/config.mk b/board/ti/omap730p2/config.mk deleted file mode 100644 index 86188204ea..0000000000 --- a/board/ti/omap730p2/config.mk +++ /dev/null @@ -1,25 +0,0 @@ -# -# (C) Copyright 2002 -# Gary Jennejohn, DENX Software Engineering, -# David Mueller, ELSOFT AG, -# -# (C) Copyright 2003 -# Texas Instruments, -# Kshitij Gupta -# -# TI Perseus 2 board with OMAP720 (ARM925EJS) cpu -# see http://www.ti.com/ for more information on Texas Instruments -# -# Innovator has 1 bank of 256 MB SDRAM -# Physical Address: -# 1000'0000 to 2000'0000 -# -# -# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000 -# (mem base + reserved) -# -# we load ourself to 1108'0000 -# -# - -CONFIG_SYS_TEXT_BASE = 0x11080000 diff --git a/board/ti/omap730p2/flash.c b/board/ti/omap730p2/flash.c deleted file mode 100644 index 56f981c47b..0000000000 --- a/board/ti/omap730p2/flash.c +++ /dev/null @@ -1,463 +0,0 @@ -/* - * (C) Copyright 2001 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2001 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2003 - * Texas Instruments, - * Kshitij Gupta - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - -#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 256 KB sectors (x2) */ -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */ - -/* Board support for 1 or 2 flash devices */ -#undef FLASH_PORT_WIDTH32 -#define FLASH_PORT_WIDTH16 - -#ifdef FLASH_PORT_WIDTH16 -#define FLASH_PORT_WIDTH ushort -#define FLASH_PORT_WIDTHV vu_short -#define SWAP(x) __swab16(x) -#else -#define FLASH_PORT_WIDTH ulong -#define FLASH_PORT_WIDTHV vu_long -#define SWAP(x) __swab32(x) -#endif - -#define FPW FLASH_PORT_WIDTH -#define FPWV FLASH_PORT_WIDTHV - -#define mb() __asm__ __volatile__ ("" : : : "memory") - - -/* Flash Organization Structure */ -typedef struct OrgDef { - unsigned int sector_number; - unsigned int sector_size; -} OrgDef; - - -/* Flash Organizations */ -OrgDef OrgIntel_28F256L18T[] = { - {4, 32 * 1024}, /* 4 * 32kBytes sectors */ - {255, 128 * 1024}, /* 255 * 128kBytes sectors */ -}; - - -/*----------------------------------------------------------------------- - * Functions - */ -unsigned long flash_init (void); -static ulong flash_get_size (FPW * addr, flash_info_t * info); -static int write_data (flash_info_t * info, ulong dest, FPW data); -static void flash_get_offsets (ulong base, flash_info_t * info); -void inline spin_wheel (void); -void flash_print_info (flash_info_t * info); -void flash_unprotect_sectors (FPWV * addr); -int flash_erase (flash_info_t * info, int s_first, int s_last); -int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt); - -/*----------------------------------------------------------------------- - */ - -unsigned long flash_init (void) -{ - int i; - ulong size = 0; - for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) { - switch (i) { - case 0: - flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]); - flash_get_offsets (PHYS_FLASH_1, &flash_info[i]); - break; - default: - panic ("configured too many flash banks!\n"); - break; - } - size += flash_info[i].size; - } - - /* Protect monitor and environment sectors - */ - flash_protect (FLAG_PROTECT_SET, - CONFIG_SYS_FLASH_BASE, - CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]); - - flash_protect (FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]); - - return size; -} - -/*----------------------------------------------------------------------- - */ -static void flash_get_offsets (ulong base, flash_info_t * info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - return; - } - - if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) { - for (i = 0; i < info->sector_count; i++) { - if (i > 255) { - info->start[i] = base + (i * 0x8000); - info->protect[i] = 0; - } else { - info->start[i] = base + - (i * PHYS_FLASH_SECT_SIZE); - info->protect[i] = 0; - } - } - } -} - -/*----------------------------------------------------------------------- - */ -void flash_print_info (flash_info_t * info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("missing or unknown FLASH type\n"); - return; - } - - switch (info->flash_id & FLASH_VENDMASK) { - case FLASH_MAN_INTEL: - printf ("INTEL "); - break; - default: - printf ("Unknown Vendor "); - break; - } - - switch (info->flash_id & FLASH_TYPEMASK) { - case FLASH_28F256L18T: - printf ("FLASH 28F256L18T\n"); - break; - default: - printf ("Unknown Chip Type\n"); - break; - } - - printf (" Size: %ld MB in %d Sectors\n", - info->size >> 20, info->sector_count); - - printf (" Sector Start Addresses:"); - for (i = 0; i < info->sector_count; ++i) { - if ((i % 5) == 0) - printf ("\n "); - printf (" %08lX%s", - info->start[i], info->protect[i] ? " (RO)" : " "); - } - printf ("\n"); - return; -} - -/* - * The following code cannot be run from FLASH! - */ -static ulong flash_get_size (FPW * addr, flash_info_t * info) -{ - volatile FPW value; - - /* Write auto select command: read Manufacturer ID */ - addr[0x5555] = (FPW) 0x00AA00AA; - addr[0x2AAA] = (FPW) 0x00550055; - addr[0x5555] = (FPW) 0x00900090; - - mb (); - value = addr[0]; - - switch (value) { - - case (FPW) INTEL_MANUFACT: - info->flash_id = FLASH_MAN_INTEL; - break; - - default: - info->flash_id = FLASH_UNKNOWN; - info->sector_count = 0; - info->size = 0; - addr[0] = (FPW) 0x00FF00FF; /* restore read mode */ - return (0); /* no or unknown flash */ - } - - mb (); - value = addr[1]; /* device ID */ - switch (value) { - - case (FPW) (INTEL_ID_28F256L18T): - info->flash_id += FLASH_28F256L18T; - info->sector_count = 259; - info->size = 0x02000000; - break; /* => 32 MB */ - - default: - info->flash_id = FLASH_UNKNOWN; - break; - } - - if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) { - printf ("** ERROR: sector count %d > max (%d) **\n", - info->sector_count, CONFIG_SYS_MAX_FLASH_SECT); - info->sector_count = CONFIG_SYS_MAX_FLASH_SECT; - } - - addr[0] = (FPW) 0x00FF00FF; /* restore read mode */ - - return (info->size); -} - - -/* unprotects a sector for write and erase - * on some intel parts, this unprotects the entire chip, but it - * wont hurt to call this additional times per sector... - */ -void flash_unprotect_sectors (FPWV * addr) -{ -#define PD_FINTEL_WSMS_READY_MASK 0x0080 - - *addr = (FPW) 0x00500050; /* clear status register */ - - /* this sends the clear lock bit command */ - *addr = (FPW) 0x00600060; - *addr = (FPW) 0x00D000D0; -} - - -/*----------------------------------------------------------------------- - */ - -int flash_erase (flash_info_t * info, int s_first, int s_last) -{ - int flag, prot, sect; - ulong type, start; - int rcode = 0; - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf ("- missing\n"); - } else { - printf ("- no sectors to erase\n"); - } - return 1; - } - - type = (info->flash_id & FLASH_VENDMASK); - if ((type != FLASH_MAN_INTEL)) { - printf ("Can't erase unknown flash type %08lx - aborted\n", - info->flash_id); - return 1; - } - - prot = 0; - for (sect = s_first; sect <= s_last; ++sect) { - if (info->protect[sect]) { - prot++; - } - } - - if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", - prot); - } else { - printf ("\n"); - } - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts (); - - /* Start erase on unprotected sectors */ - for (sect = s_first; sect <= s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - FPWV *addr = (FPWV *) (info->start[sect]); - FPW status; - - printf ("Erasing sector %2d ... ", sect); - - flash_unprotect_sectors (addr); - - /* arm simple, non interrupt dependent timer */ - start = get_timer(0); - - *addr = (FPW) 0x00500050;/* clear status register */ - *addr = (FPW) 0x00200020;/* erase setup */ - *addr = (FPW) 0x00D000D0;/* erase confirm */ - - while (((status = - *addr) & (FPW) 0x00800080) != - (FPW) 0x00800080) { - if (get_timer(start) > - CONFIG_SYS_FLASH_ERASE_TOUT) { - printf ("Timeout\n"); - /* suspend erase */ - *addr = (FPW) 0x00B000B0; - /* reset to read mode */ - *addr = (FPW) 0x00FF00FF; - rcode = 1; - break; - } - } - - /* clear status register cmd. */ - *addr = (FPW) 0x00500050; - *addr = (FPW) 0x00FF00FF;/* resest to read mode */ - printf (" done\n"); - } - } - - if (flag) - enable_interrupts(); - - return rcode; -} - -/*----------------------------------------------------------------------- - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - * 4 - Flash not identified - */ - -int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) -{ - ulong cp, wp; - FPW data; - int count, i, l, rc, port_width; - - if (info->flash_id == FLASH_UNKNOWN) { - return 4; - } -/* get lower word aligned address */ -#ifdef FLASH_PORT_WIDTH16 - wp = (addr & ~1); - port_width = 2; -#else - wp = (addr & ~3); - port_width = 4; -#endif - - /* - * handle unaligned start bytes - */ - if ((l = addr - wp) != 0) { - data = 0; - for (i = 0, cp = wp; i < l; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - for (; i < port_width && cnt > 0; ++i) { - data = (data << 8) | *src++; - --cnt; - ++cp; - } - for (; cnt == 0 && i < port_width; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - - if ((rc = write_data (info, wp, SWAP (data))) != 0) { - return (rc); - } - wp += port_width; - } - - /* - * handle word aligned part - */ - count = 0; - while (cnt >= port_width) { - data = 0; - for (i = 0; i < port_width; ++i) { - data = (data << 8) | *src++; - } - if ((rc = write_data (info, wp, SWAP (data))) != 0) { - return (rc); - } - wp += port_width; - cnt -= port_width; - if (count++ > 0x800) { - spin_wheel (); - count = 0; - } - } - - if (cnt == 0) { - return (0); - } - - /* - * handle unaligned tail bytes - */ - data = 0; - for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) { - data = (data << 8) | *src++; - --cnt; - } - for (; i < port_width; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - - return (write_data (info, wp, SWAP (data))); -} - -/*----------------------------------------------------------------------- - * Write a word or halfword to Flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -static int write_data (flash_info_t * info, ulong dest, FPW data) -{ - FPWV *addr = (FPWV *) dest; - ulong status; - int flag, rc = 0; - ulong start; - - /* Check if Flash is (sufficiently) erased */ - if ((*addr & data) != data) { - printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr); - return (2); - } - flash_unprotect_sectors (addr); - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts (); - *addr = (FPW) 0x00400040; /* write setup */ - *addr = data; - - /* arm simple, non interrupt dependent timer */ - start = get_timer(0); - - /* wait while polling the status register */ - while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) { - if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) { - rc = 1; - goto done; - } - } -done: - *addr = (FPW)0x00FF00FF; /* restore read mode */ - if (flag) - enable_interrupts(); - return rc; -} - -void inline spin_wheel (void) -{ - static int p = 0; - static char w[] = "\\/-"; - - printf ("\010%c", w[p]); - (++p == 3) ? (p = 0) : 0; -} diff --git a/board/ti/omap730p2/lowlevel_init.S b/board/ti/omap730p2/lowlevel_init.S deleted file mode 100644 index 795c495372..0000000000 --- a/board/ti/omap730p2/lowlevel_init.S +++ /dev/null @@ -1,379 +0,0 @@ -/* - * Board specific setup info - * - * (C) Copyright 2003-2004 - * - * Texas Instruments, - * Kshitij Gupta - * - * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004 - * - * Modified for OMAP730 P2 Board by Dave Peverley, MPC-Data Limited - * (http://www.mpc-data.co.uk) - * - * TODO : Tidy up and change to use system register defines - * from omap730.h where possible. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - -#if defined(CONFIG_OMAP730) -#include <./configs/omap730.h> -#endif - -_TEXT_BASE: - .word CONFIG_SYS_TEXT_BASE /* sdram load addr from config.mk */ - -.globl lowlevel_init -lowlevel_init: - /* Save callers address in r11 - r11 must never be modified */ - mov r11, lr - - /*------------------------------------------------------* - *mask all IRQs by setting all bits in the INTMR default* - *------------------------------------------------------*/ - mov r1, #0xffffffff - ldr r0, =REG_IHL1_MIR - str r1, [r0] - ldr r0, =REG_IHL2_MIR - str r1, [r0] - - /*------------------------------------------------------* - * Set up ARM CLM registers (IDLECT1) * - *------------------------------------------------------*/ - ldr r0, REG_ARM_IDLECT1 - ldr r1, VAL_ARM_IDLECT1 - str r1, [r0] - - /*------------------------------------------------------* - * Set up ARM CLM registers (IDLECT2) * - *------------------------------------------------------*/ - ldr r0, REG_ARM_IDLECT2 - ldr r1, VAL_ARM_IDLECT2 - str r1, [r0] - - /*------------------------------------------------------* - * Set up ARM CLM registers (IDLECT3) * - *------------------------------------------------------*/ - ldr r0, REG_ARM_IDLECT3 - ldr r1, VAL_ARM_IDLECT3 - str r1, [r0] - - - mov r1, #0x01 /* PER_EN bit */ - ldr r0, REG_ARM_RSTCT2 - strh r1, [r0] /* CLKM; Peripheral reset. */ - - /* Set CLKM to Sync-Scalable */ - /* I supposedly need to enable the dsp clock before switching */ - mov r1, #0x1000 - ldr r0, REG_ARM_SYSST - strh r1, [r0] - mov r0, #0x400 -1: - subs r0, r0, #0x1 /* wait for any bubbles to finish */ - bne 1b - ldr r1, VAL_ARM_CKCTL - ldr r0, REG_ARM_CKCTL - strh r1, [r0] - - /* a few nops to let settle */ - nop - nop - nop - nop - nop - nop - nop - nop - nop - nop - - /* setup DPLL 1 */ - /* Ramp up the clock to 96Mhz */ - ldr r1, VAL_DPLL1_CTL - ldr r0, REG_DPLL1_CTL - strh r1, [r0] - ands r1, r1, #0x10 /* Check if PLL is enabled. */ - beq lock_end /* Do not look for lock if BYPASS selected */ -2: - ldrh r1, [r0] - ands r1, r1, #0x01 /* Check the LOCK bit.*/ - beq 2b /* loop until bit goes hi. */ -lock_end: - - /*------------------------------------------------------* - * Turn off the watchdog during init... * - *------------------------------------------------------*/ - ldr r0, REG_WATCHDOG - ldr r1, WATCHDOG_VAL1 - str r1, [r0] - ldr r1, WATCHDOG_VAL2 - str r1, [r0] - ldr r0, REG_WSPRDOG - ldr r1, WSPRDOG_VAL1 - str r1, [r0] - ldr r0, REG_WWPSDOG - -watch1Wait: - ldr r1, [r0] - tst r1, #0x10 - bne watch1Wait - - ldr r0, REG_WSPRDOG - ldr r1, WSPRDOG_VAL2 - str r1, [r0] - ldr r0, REG_WWPSDOG -watch2Wait: - ldr r1, [r0] - tst r1, #0x10 - bne watch2Wait - - /* Set memory timings corresponding to the new clock speed */ - - /* Check execution location to determine current execution location - * and branch to appropriate initialization code. - */ - /* Compare physical SDRAM base & current execution location. */ - and r0, pc, #0xF0000000 - /* Compare. */ - cmp r0, #0 - /* Skip over EMIF-fast initialization if running from SDRAM. */ - bne skip_sdram - - /* - * Delay for SDRAM initialization. - */ - mov r3, #0x1800 /* value should be checked */ -3: - subs r3, r3, #0x1 /* Decrement count */ - bne 3b - - ldr r0, REG_SDRAM_CONFIG - ldr r1, SDRAM_CONFIG_VAL - str r1, [r0] - - ldr r0, REG_SDRAM_MRS_LEGACY - ldr r1, SDRAM_MRS_VAL - str r1, [r0] - -skip_sdram: - -common_tc: - /* slow interface */ - ldr r1, VAL_TC_EMIFS_CS0_CONFIG - ldr r0, REG_TC_EMIFS_CS0_CONFIG - str r1, [r0] /* Chip Select 0 */ - - ldr r1, VAL_TC_EMIFS_CS1_CONFIG - ldr r0, REG_TC_EMIFS_CS1_CONFIG - str r1, [r0] /* Chip Select 1 */ - ldr r1, VAL_TC_EMIFS_CS2_CONFIG - ldr r0, REG_TC_EMIFS_CS2_CONFIG - str r1, [r0] /* Chip Select 2 */ - ldr r1, VAL_TC_EMIFS_CS3_CONFIG - ldr r0, REG_TC_EMIFS_CS3_CONFIG - str r1, [r0] /* Chip Select 3 */ - - /* 48MHz clock request for UART1 */ - ldr r1, PERSEUS2_CONFIG_BASE - ldrh r0, [r1, #CONFIG_PCC_CONF] - orr r0, r0, #CONF_MOD_UART1_CLK_MODE_R - strh r0, [r1, #CONFIG_PCC_CONF] - - /* Initialize public and private rheas - * - set access factor 2 on both rhea / strobe - * - disable write buffer on strb0, enable write buffer on strb1 - */ - - ldr R0, REG_RHEA_PUB_CTL - ldr R1, REG_RHEA_PRIV_CTL - ldr R2, VAL_RHEA_CTL - strh R2, [R0] - strh R2, [R1] - mov R3, #2 /* disable write buffer on strb0, enable write buffer on strb1 */ - strh R3, [R0, #0x08] /* arm rhea control reg */ - strh R3, [R1, #0x08] - - /* enable IRQ and FIQ */ - - mrs r4, CPSR - bic r4, r4, #IRQ_MASK - bic r4, r4, #FIQ_MASK - msr CPSR, r4 - - /* set TAP CONF to TRI EMULATION */ - - ldr r1, [r0, #CONFIG_MODE2] - bic r1, r1, #0x18 - orr r1, r1, #0x10 - str r1, [r0, #CONFIG_MODE2] - - /* set tdbgen to 1 */ - - ldr r0, PERSEUS2_CONFIG_BASE - ldr r1, [r0, #CONFIG_MODE1] - mov r2, #0x10000 - orr r1, r1, r2 - str r1, [r0, #CONFIG_MODE1] - -#ifdef CONFIG_P2_OMAP1610 - /* inserting additional 2 clock cycle hold time for LAN */ - ldr r0, REG_TC_EMIFS_CS1_ADVANCED - ldr r1, VAL_TC_EMIFS_CS1_ADVANCED - str r1, [r0] -#endif - /* Start MPU Timer 1 */ - ldr r0, REG_MPU_LOAD_TIMER - ldr r1, VAL_MPU_LOAD_TIMER - str r1, [r0] - - ldr r0, REG_MPU_CNTL_TIMER - ldr r1, VAL_MPU_CNTL_TIMER - str r1, [r0] - - /* back to arch calling code */ - mov pc, r11 - - /* the literal pools origin */ - .ltorg - -REG_TC_EMIFS_CONFIG: /* 32 bits */ - .word 0xfffecc0c -REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */ - .word 0xfffecc10 -REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */ - .word 0xfffecc14 -REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */ - .word 0xfffecc18 -REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */ - .word 0xfffecc1c - -#ifdef CONFIG_P2_OMAP730 -REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */ - .word 0xfffecc54 -#endif - -/* MPU clock/reset/power mode control registers */ -REG_ARM_CKCTL: /* 16 bits */ - .word 0xfffece00 - -REG_ARM_IDLECT3: /* 16 bits */ - .word 0xfffece24 -REG_ARM_IDLECT2: /* 16 bits */ - .word 0xfffece08 -REG_ARM_IDLECT1: /* 16 bits */ - .word 0xfffece04 - -REG_ARM_RSTCT2: /* 16 bits */ - .word 0xfffece14 -REG_ARM_SYSST: /* 16 bits */ - .word 0xfffece18 -/* DPLL control registers */ -REG_DPLL1_CTL: /* 16 bits */ - .word 0xfffecf00 - -/* Watch Dog register */ -/* secure watchdog stop */ -REG_WSPRDOG: - .word 0xfffeb048 -/* watchdog write pending */ -REG_WWPSDOG: - .word 0xfffeb034 - -WSPRDOG_VAL1: - .word 0x0000aaaa -WSPRDOG_VAL2: - .word 0x00005555 - -/* SDRAM config is: auto refresh enabled, 16 bit 4 bank, - counter @8192 rows, 10 ns, 8 burst */ -REG_SDRAM_CONFIG: - .word 0xfffecc20 - -REG_SDRAM_MRS_LEGACY: - .word 0xfffecc24 - -REG_WATCHDOG: - .word 0xfffec808 - -REG_MPU_LOAD_TIMER: - .word 0xfffec504 -REG_MPU_CNTL_TIMER: - .word 0xfffec500 - -/* Public and private rhea bridge registers definition */ - -REG_RHEA_PUB_CTL: - .word 0xFFFECA00 - -REG_RHEA_PRIV_CTL: - .word 0xFFFED300 - -/* EMIFF SDRAM Configuration register - - self refresh disable - - auto refresh enabled - - SDRAM type 64 Mb, 16 bits bus 4 banks - - power down enabled - - SDRAM clock disabled - */ -SDRAM_CONFIG_VAL: - .word 0x0C017DF4 - -/* Burst full page length ; cas latency = 3 */ -SDRAM_MRS_VAL: - .word 0x00000037 - -VAL_ARM_CKCTL: - .word 0x6505 -VAL_DPLL1_CTL: - .word 0x3412 - -#ifdef CONFIG_P2_OMAP730 -VAL_TC_EMIFS_CS0_CONFIG: - .word 0x0000FFF3 -VAL_TC_EMIFS_CS1_CONFIG: - .word 0x00004278 -VAL_TC_EMIFS_CS2_CONFIG: - .word 0x00004278 -VAL_TC_EMIFS_CS3_CONFIG: - .word 0x00004278 -VAL_TC_EMIFS_CS1_ADVANCED: - .word 0x00000022 -#endif - -VAL_ARM_IDLECT1: - .word 0x00000400 -VAL_ARM_IDLECT2: - .word 0x00000886 -VAL_ARM_IDLECT3: - .word 0x00000015 - -WATCHDOG_VAL1: - .word 0x000000f5 -WATCHDOG_VAL2: - .word 0x000000a0 - -VAL_MPU_LOAD_TIMER: - .word 0xffffffff -VAL_MPU_CNTL_TIMER: - .word 0xffffffa1 - -VAL_RHEA_CTL: - .word 0xFF22 - -/* Config Register vals */ -PERSEUS2_CONFIG_BASE: - .word 0xFFFE1000 - -.equ CONFIG_PCC_CONF, 0xB4 -.equ CONFIG_MODE1, 0x10 -.equ CONFIG_MODE2, 0x14 -.equ CONF_MOD_UART1_CLK_MODE_R, 0x0A - -/* misc values */ -.equ IRQ_MASK, 0x80 /* IRQ mask value */ -.equ FIQ_MASK, 0x40 /* FIQ mask value */ diff --git a/board/ti/omap730p2/omap730p2.c b/board/ti/omap730p2/omap730p2.c deleted file mode 100644 index 554019c207..0000000000 --- a/board/ti/omap730p2/omap730p2.c +++ /dev/null @@ -1,255 +0,0 @@ -/* - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * (C) Copyright 2002 - * David Mueller, ELSOFT AG, - * - * (C) Copyright 2003 - * Texas Instruments, - * Kshitij Gupta - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#if defined(CONFIG_OMAP730) -#include <./configs/omap730.h> -#endif - -DECLARE_GLOBAL_DATA_PTR; - -int test_boot_mode(void); -void spin_up_leds(void); -void flash__init (void); -void ether__init (void); -void set_muxconf_regs (void); -void peripheral_power_enable (void); - -#define FLASH_ON_CS0 1 -#define FLASH_ON_CS3 0 - -static inline void delay (unsigned long loops) -{ - __asm__ volatile ("1:\n" - "subs %0, %1, #1\n" - "bne 1b":"=r" (loops):"0" (loops)); -} - -int test_boot_mode(void) -{ - /* Check for CS0 and CS3 address decode swapping */ - if (*((volatile int *)EMIFS_CONFIG) & 0x00000002) - return(FLASH_ON_CS3); - else - return(FLASH_ON_CS0); -} - -/* Toggle backup LED indication */ -void toggle_backup_led(void) -{ - static int backupLEDState = 0; /* Init variable so that the LED will be ON the first time */ - volatile unsigned int *IOConfReg; - - - IOConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DATA_OUTPUT); - - if (backupLEDState != 0) { - *IOConfReg &= (0xFFFFEFFF); - backupLEDState = 0; - } else { - *IOConfReg |= (0x00001000); - backupLEDState = 1; - } -} - -/* - * Miscellaneous platform dependent initialisations - */ - -int board_init (void) -{ - /* arch number of OMAP 730 P2 Board - Same as the Innovator! */ - gd->bd->bi_arch_number = MACH_TYPE_OMAP_PERSEUS2; - - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x10000100; - - /* Configure MUX settings */ - set_muxconf_regs (); - - peripheral_power_enable (); - - /* Backup LED indication via GPIO_140 -> Red led if MUX correctly setup */ - toggle_backup_led(); - - /* Hold GSM in reset until needed */ - *((volatile unsigned short *)M_CTL) &= ~1; - - /* - * CSx timings, GPIO Mux ... setup - */ - - /* Flash: CS0 timings setup */ - *((volatile unsigned int *) FLASH_CFG_0) = 0x0000fff3; - *((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000088; - - /* Ethernet support trough the debug board */ - /* CS1 timings setup */ - *((volatile unsigned int *) FLASH_CFG_1) = 0x0000fff3; - *((volatile unsigned int *) FLASH_ACFG_0_1) = 0x00000000; - - /* this speeds up your boot a quite a bit. However to make it - * work, you need make sure your kernel startup flush bug is fixed. - * ... rkw ... - */ - icache_enable (); - - flash__init (); - ether__init (); - - return 0; -} - -/****************************** - Routine: - Description: -******************************/ -void flash__init (void) -{ - unsigned int regval; - - regval = *((volatile unsigned int *) EMIFS_CONFIG); - /* Turn off write protection for flash devices. */ - regval = regval | 0x0001; - *((volatile unsigned int *) EMIFS_CONFIG) = regval; -} - -/************************************************************* - Routine:ether__init - Description: take the Ethernet controller out of reset and wait - for the EEPROM load to complete. -*************************************************************/ -void ether__init (void) -{ -#define LAN_RESET_REGISTER 0x0400001c - - *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000; - do { - *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0001; - udelay (100); - } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0001); - - do { - *((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000; - udelay (100); - } while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0000); - -#define ETH_CONTROL_REG 0x0400030b - - *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01; - udelay (100); -} - -/****************************** - Routine: - Description: -******************************/ -int dram_init (void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; - - return 0; -} - -/****************************************************** - Routine: set_muxconf_regs - Description: Setting up the configuration Mux registers - specific to the hardware -*******************************************************/ -void set_muxconf_regs (void) -{ - volatile unsigned int *MuxConfReg; - /* set each registers to its reset value; */ - - /* - * Backup LED Indication - */ - - /* Configure MUXed pin. Mode 6: GPIO_140 */ - MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF10); - *MuxConfReg &= (0xFFFFFF1F); /* Clear D_MPU_LPG1 */ - *MuxConfReg |= 0x000000C0; /* Set D_MPU_LPG1 to 0x6 */ - - /* Configure GPIO_140 as output */ - MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DIRECTION_CONTROL); - *MuxConfReg &= (0xFFFFEFFF); /* Clear direction (output) for GPIO 140 */ - - /* - * Configure GPIOs for battery charge & feedback - */ - - /* Configure MUXed pin. Mode 6: GPIO_35 */ - MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3); - *MuxConfReg &= 0xFFFFFFF1; /* Clear M_CLK_OUT */ - *MuxConfReg |= 0x0000000C; /* Set M_CLK_OUT = 0x6 (GPIOs) */ - - /* Configure MUXed pin. Mode 6: GPIO_72,73,74 */ - MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF5); - *MuxConfReg &= 0xFFFF1FFF; /* Clear D_DDR */ - *MuxConfReg |= 0x0000C000; /* Set D_DDR = 0x6 (GPIOs) */ - - MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DIRECTION_CONTROL); - *MuxConfReg |= 0x00000100; /* Configure GPIO_72 as input */ - *MuxConfReg &= 0xFFFFFDFF; /* Configure GPIO_73 as output */ - - /* - * Allow battery charge - */ - - MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DATA_OUTPUT); - *MuxConfReg &= (0xFFFFFDFF); /* Clear GPIO_73 pin */ - - /* - * Configure MPU_EXT_NIRQ IO in IO_CONF9 register, - * It is used as the Ethernet controller interrupt - */ - MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF9); - *MuxConfReg &= 0x1FFFFFFF; -} - -/****************************************************** - Routine: peripheral_power_enable - Description: Enable the power for UART1 -*******************************************************/ -void peripheral_power_enable (void) -{ - volatile unsigned int *MuxConfReg; - - - /* Set up pins used by UART */ - - /* Start UART clock (48MHz) */ - MuxConfReg = (volatile unsigned int *) (PERSEUS_PCC_CONF_REG); - *MuxConfReg &= (0xFFFFFFF7); - *MuxConfReg |= (0x00000008); - - /* Get the UART pin in mode0 */ - MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3); - *MuxConfReg &= (0xFF1FFFFF); - *MuxConfReg &= (0xF1FFFFFF); -} - -#ifdef CONFIG_CMD_NET -int board_eth_init(bd_t *bis) -{ - int rc = 0; -#ifdef CONFIG_LAN91C96 - rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE); -#endif - return rc; -} -#endif diff --git a/boards.cfg b/boards.cfg index efecbc2720..36f09242a5 100644 --- a/boards.cfg +++ b/boards.cfg @@ -213,9 +213,6 @@ Active arm arm926ejs mxs schulercontrol sc_sps_1 Active arm arm926ejs nomadik st nhk8815 nhk8815 - Nomadik Linux Team :Alessandro Rubini Active arm arm926ejs nomadik st nhk8815 nhk8815_onenand nhk8815:BOOT_ONENAND Nomadik Linux Team :Alessandro Rubini Active arm arm926ejs omap ti - omap5912osk - Rishi Bhattacharya -Active arm arm926ejs omap ti omap730p2 omap730p2 omap730p2:CS3_BOOT Dave Peverley -Active arm arm926ejs omap ti omap730p2 omap730p2_cs0boot omap730p2:CS0_BOOT Dave Peverley -Active arm arm926ejs omap ti omap730p2 omap730p2_cs3boot omap730p2:CS3_BOOT Dave Peverley Active arm arm926ejs orion5x LaCie - edminiv2 - Albert ARIBAUD Active arm arm926ejs pantheon Marvell - dkb - Lei Wen Active arm arm926ejs spear spear - x600 x600 Stefan Roese diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 8ed09c7103..a48ce7c866 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -11,8 +11,9 @@ easily if here is something they might want to dig for... Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= -pdnb3 arm ixp - 2013-09-24 Stefan Roese -scpu arm ixp - 2013-09-24 Stefan Roese +omap730p2 arm arm926ejs - 2013-11-11 +pdnb3 arm ixp 304db0b 2013-09-24 Stefan Roese +scpu arm ixp 304db0b 2013-09-24 Stefan Roese omap1510inn arm arm925t 0610a16 2013-09-23 Kshitij Gupta CANBT powerpc 405CR fb8f4fd 2013-08-07 Matthias Fuchs Alaska8220 powerpc mpc8220 d6ed322 2013-05-11 diff --git a/include/configs/h2_p2_dbg_board.h b/include/configs/h2_p2_dbg_board.h deleted file mode 100644 index 4ba2c55e98..0000000000 --- a/include/configs/h2_p2_dbg_board.h +++ /dev/null @@ -1,120 +0,0 @@ -/* - * - * BRIEF MODULE DESCRIPTION - * TI H2 and P2 Debug Board hardware map - * - * Copyright (C) 2004 MPC-Data Limited. (http://www.mpc-data.co.uk) - * Author: MPC-Data Limited - * Dave Peverley - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __INCLUDED_H2_P2_DBH_BOARD_H -#define __INCLUDED_H2_P2_DBH_BOARD_H - -#include - -/* - * The Debug board is designed to function with the P2 Sample, H2 - * Sample and 1610 Innovator boards. The main difference AFAICT is - * the chip selects used with each system ; - * - * P2 Sample : CS1 of OMAP730 is used to select the CPLD & LAN regs - * H2 Sample : CS1a is used to select the CPLD registers. - * - */ - -/*************************************************************************** - * CPLD Registers - **************************************************************************/ - -#define H2DBG_CPLD_REVISION 0x04000010 -#define H2DBG_BOARD_REVISION 0x04000012 -#define H2DBG_GPIO_REGISTER 0x04000014 -#define H2DBG_LED_CONTROL 0x04000016 -#define H2DBG_MISC_INPUT 0x04000018 -#define H2DBG_LAN_STATUS 0x0400001A -#define H2DBG_LAN_RESET 0x0400001C -#define H2DBG_ETH_REG_BASE 0x04000300 - -/*************************************************************************** - * Ethernet Control Registers - * These are for the LAN91C96 on the debug board - **************************************************************************/ - -/* Bank 0 in IO space */ - -#define ETH_TCR (H2DBG_ETH_REG_BASE + 0x00) /* Transmit Control Register */ -#define ETH_EPH_STATUS (H2DBG_ETH_REG_BASE + 0x02) /* EPH Status Register */ -#define ETH_RCR (H2DBG_ETH_REG_BASE + 0x04) /* Receive Control Register */ -#define ETH_COUNTER (H2DBG_ETH_REG_BASE + 0x06) /* Counter Register */ -#define ETH_MIR (H2DBG_ETH_REG_BASE + 0x08) /* Memory Information Register */ -#define ETH_MCR (H2DBG_ETH_REG_BASE + 0x0A) /* Memory Configuration Register */ - -/* Bank 1 in IO space */ - -#define ETH_CONFIG (H2DBG_ETH_REG_BASE + 0x00) /* Configuration Register */ -#define ETH_BASE (H2DBG_ETH_REG_BASE + 0x02) /* Base Address Register */ -#define ETH_IA0 (H2DBG_ETH_REG_BASE + 0x04) /* Individual Address Register - 0 */ -#define ETH_IA1 (H2DBG_ETH_REG_BASE + 0x05) /* Individual Address Register - 1 */ -#define ETH_IA2 (H2DBG_ETH_REG_BASE + 0x06) /* Individual Address Register - 2 */ -#define ETH_IA3 (H2DBG_ETH_REG_BASE + 0x07) /* Individual Address Register - 3 */ -#define ETH_IA4 (H2DBG_ETH_REG_BASE + 0x08) /* Individual Address Register - 4 */ -#define ETH_IA5 (H2DBG_ETH_REG_BASE + 0x09) /* Individual Address Register - 5 */ -#define ETH_GEN_PURPOSE (H2DBG_ETH_REG_BASE + 0x0A) /* General Address Registers */ -#define ETH_CONTROL (H2DBG_ETH_REG_BASE + 0x0B) /* Control Register */ - -/* Bank 2 in IO space */ - -#define ETH_MMU (H2DBG_ETH_REG_BASE + 0x00) /* MMU Command Register */ -#define ETH_AUTO_TX_START (H2DBG_ETH_REG_BASE + 0x01) /* Auto Tx Start Register */ -#define ETH_PNR (H2DBG_ETH_REG_BASE + 0x02) /* Packet Number Register */ -#define ETH_ARR (H2DBG_ETH_REG_BASE + 0x03) /* Allocation Result Register */ -#define ETH_FIFO (H2DBG_ETH_REG_BASE + 0x04) /* FIFO Ports Register */ -#define ETH_POINTER (H2DBG_ETH_REG_BASE + 0x06) /* Pointer Register */ -#define ETH_DATA_HIGH (H2DBG_ETH_REG_BASE + 0x08) /* Data High Register */ -#define ETH_DATA_LOW (H2DBG_ETH_REG_BASE + 0x0A) /* Data Low Register */ -#define ETH_INT_STATS (H2DBG_ETH_REG_BASE + 0x0C) /* Interrupt Status Register - RO */ -#define ETH_INT_ACK (H2DBG_ETH_REG_BASE + 0x0C) /* Interrupt Acknowledge Register -WO */ -#define ETH_INT_MASK (H2DBG_ETH_REG_BASE + 0x0D) /* Interrupt Mask Register */ - - -#ifndef __ASSEMBLY__ - -/* - * A couple of utility inlines to aid debugging using the LED's on the - * debug board. - */ - -static inline void set_led_state(int state) -{ - static unsigned long hw_led_state = 0; - volatile unsigned short *led_address = (volatile unsigned short *)0x04000016; - - hw_led_state = ((unsigned long)state); - *((unsigned short *) (led_address)) = (unsigned short) (~hw_led_state & 0xFFFF); -} - - -static inline void spin_up_leds(void) -{ - volatile int i, j, k; - - for (k = 0; k < 2; k++) { - for (i = 0; i < 16; i++) { - for (j = 0; j < 5000; j++) { - set_led_state(1 << i); - } - } - for (i = 15; i >= 0; i--) { - for (j = 0; j < 5000; j++) { - set_led_state(1 << i); - } - } - } -} - -#endif /* ! __ASSEMBLY__ */ - -#endif /* ! __INCLUDED_H2_P2_DBH_BOARD_H */ diff --git a/include/configs/omap730.h b/include/configs/omap730.h deleted file mode 100644 index b54e0fb2da..0000000000 --- a/include/configs/omap730.h +++ /dev/null @@ -1,246 +0,0 @@ -/* - * - * BRIEF MODULE DESCRIPTION - * OMAP730 hardware map - * - * Copyright (C) 2004 MPC-Data Limited. (http://www.mpc-data.co.uk) - * Author: MPC-Data Limited - * Dave Peverley - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __INCLUDED_OMAP730_H -#define __INCLUDED_OMAP730_H - -#include - -/*************************************************************************** - * OMAP730 Configuration Registers - **************************************************************************/ - -#define PERSEUS2_MPU_DEV_ID ((unsigned int)(0xFFFE1000)) -#define PERSEUS2_GSM_DEV_ID0 ((unsigned int)(0xFFFE1000)) -#define PERSEUS2_GDM_DEV_ID1 ((unsigned int)(0xFFFE1002)) -#define DSP_CONF ((unsigned int)(0xFFFE1004)) -#define PERSEUS2_MPU_DIE_ID0 ((unsigned int)(0xFFFE1008)) -#define GSM_ASIC_CONF ((unsigned int)(0xFFFE1008)) -#define PERSEUS2_MPU_DIE_ID1 ((unsigned int)(0xFFFE100C)) -#define PERSEUS2_MODE1 ((unsigned int)(0xFFFE1010)) -#define PERSEUS2_GSM_DIE_ID0 ((unsigned int)(0xFFFE1010)) -#define PERSEUS2_GSM_DIE_ID1 ((unsigned int)(0xFFFE1012)) -#define PERSEUS2_MODE2 ((unsigned int)(0xFFFE1014)) -#define PERSEUS2_GSM_DIE_ID2 ((unsigned int)(0xFFFE1014)) -#define PERSEUS2_GSM_DIE_ID3 ((unsigned int)(0xFFFE1016)) -#define PERSEUS2_ANALOG_CELLS_CONF ((unsigned int)(0xFFFE1018)) -#define SPECCTL ((unsigned int)(0xFFFE101C)) -#define SPARE1 ((unsigned int)(0xFFFE1020)) -#define SPARE2 ((unsigned int)(0xFFFE1024)) -#define GSM_PBG_IRQ ((unsigned int)(0xFFFE1028)) -#define DMA_REQ_CONF ((unsigned int)(0xFFFE1030)) -#define PE_CONF_NO_DUAL ((unsigned int)(0xFFFE1060)) -#define PERSEUS2_IO_CONF0 ((unsigned int)(0xFFFE1070)) -#define PERSEUS2_IO_CONF1 ((unsigned int)(0xFFFE1074)) -#define PERSEUS2_IO_CONF2 ((unsigned int)(0xFFFE1078)) -#define PERSEUS2_IO_CONF3 ((unsigned int)(0xFFFE107C)) -#define PERSEUS2_IO_CONF4 ((unsigned int)(0xFFFE1080)) -#define PERSEUS2_IO_CONF5 ((unsigned int)(0xFFFE1084)) -#define PERSEUS2_IO_CONF6 ((unsigned int)(0xFFFE1088)) -#define PERSEUS2_IO_CONF7 ((unsigned int)(0xFFFE108C)) -#define PERSEUS2_IO_CONF8 ((unsigned int)(0xFFFE1090)) -#define PERSEUS2_IO_CONF9 ((unsigned int)(0xFFFE1094)) -#define PERSEUS2_IO_CONF10 ((unsigned int)(0xFFFE1098)) -#define PERSEUS2_IO_CONF11 ((unsigned int)(0xFFFE109C)) -#define PERSEUS2_IO_CONF12 ((unsigned int)(0xFFFE10A0)) -#define PERSEUS2_IO_CONF13 ((unsigned int)(0xFFFE10A4)) -#define PERSEUS_PCC_CONF_REG ((unsigned int)(0xFFFE10B4)) -#define BIST_STATUS_INTERNAL ((unsigned int)(0xFFFE10B8)) -#define BIST_CONTROL ((unsigned int)(0xFFFE10C0)) -#define BOOT_ROM_REG ((unsigned int)(0xFFFE10C4)) -#define PRODUCTION_ID_REG ((unsigned int)(0xFFFE10C8)) -#define BIST_SECROM_SIGNATURE1_INTERNAL ((unsigned int)(0xFFFE10D0)) -#define BIST_SECROM_SIGNATURE2_INTERNAL ((unsigned int)(0xFFFE10D4)) -#define BIST_CONTROL_2 ((unsigned int)(0xFFFE10D8)) -#define DEBUG1 ((unsigned int)(0xFFFE10E0)) -#define DEBUG2 ((unsigned int)(0xFFFE10E4)) -#define DEBUG_DMA_IRQ ((unsigned int)(0xFFFE10E8)) - -/*************************************************************************** - * OMAP730 EMIFS Registers (TRM 2.5.7) - **************************************************************************/ - -#define TCMIF_BASE 0xFFFECC00 - -#define EMIFS_LRUREG (TCMIF_BASE + 0x04) -#define EMIFS_CONFIG (TCMIF_BASE + 0x0C) -#define FLASH_CFG_0 (TCMIF_BASE + 0x10) -#define FLASH_CFG_1 (TCMIF_BASE + 0x14) -#define FLASH_CFG_2 (TCMIF_BASE + 0x18) -#define FLASH_CFG_3 (TCMIF_BASE + 0x1C) -#define FL_CFG_DYN_WAIT (TCMIF_BASE + 0x40) -#define EMIFS_TIMEOUT1_REG (TCMIF_BASE + 0x28) -#define EMIFS_TIMEOUT2_REG (TCMIF_BASE + 0x2C) -#define EMIFS_TIMEOUT3_REG (TCMIF_BASE + 0x30) -#define EMIFS_ABORT_ADDR (TCMIF_BASE + 0x44) -#define EMIFS_ABORT_TYPE (TCMIF_BASE + 0x48) -#define EMIFS_ABORT_TOUT (TCMIF_BASE + 0x4C) -#define FLASH_ACFG_0_1 (TCMIF_BASE + 0x50) -#define FLASH_ACFG_1_1 (TCMIF_BASE + 0x54) -#define FLASH_ACFG_2_1 (TCMIF_BASE + 0x58) -#define FLASH_ACFG_3_1 (TCMIF_BASE + 0x5C) - -/*************************************************************************** - * OMAP730 Interrupt handlers - **************************************************************************/ - -#define OMAP_IH1_BASE 0xFFFECB00 /* MPU Level 1 IRQ handler */ -#define OMAP_IH2_BASE 0xfffe0000 - -/*************************************************************************** - * OMAP730 Timers - * - * There are three general purpose OS timers in the 730 that can be - * configured in autoreload or one-shot modes. - **************************************************************************/ - -#define OMAP730_32kHz_TIMER_BASE 0xFFFB9000 - -/* 32k Timer Registers */ -#define TIMER32k_CR 0x08 -#define TIMER32k_TVR 0x00 -#define TIMER32k_TCR 0x04 - -/* 32k Timer Control Register definition */ -#define TIMER32k_TSS (1<<0) -#define TIMER32k_TRB (1<<1) -#define TIMER32k_INT (1<<2) -#define TIMER32k_ARL (1<<3) - -/* MPU Timer base addresses */ -#define OMAP730_MPUTIMER_BASE 0xfffec500 -#define OMAP730_MPUTIMER_OFF 0x00000100 - -#define OMAP730_TIMER1_BASE 0xFFFEC500 -#define OMAP730_TIMER2_BASE 0xFFFEC600 -#define OMAP730_TIMER3_BASE 0xFFFEC700 - -/* MPU Timer Register offsets */ -#define CNTL_TIMER 0x00 /* MPU_CNTL_TIMER */ -#define LOAD_TIM 0x04 /* MPU_LOAD_TIMER */ -#define READ_TIM 0x08 /* MPU_READ_TIMER */ - -/* MPU_CNTL_TIMER register bits */ -#define MPUTIM_FREE (1<<6) -#define MPUTIM_CLOCK_ENABLE (1<<5) -#define MPUTIM_PTV_MASK (0x7< - * - * Configuation settings for the TI OMAP Perseus 2 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_ARM926EJS 1 /* This is an arm926ejs CPU core */ -#define CONFIG_OMAP 1 /* in a TI OMAP core */ -#define CONFIG_OMAP730 1 /* which is in a 730 */ -#define CONFIG_P2_OMAP730 1 /* a Perseus 2 Board */ - -/* - * Input clock of PLL - * The OMAP730 Perseus 2 has 13MHz input clock - */ - -#define CONFIG_SYS_CLK_FREQ 13000000 - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 - -/* - * Size of malloc() pool - */ - -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* - * Hardware drivers - */ - -#define CONFIG_LAN91C96 -#define CONFIG_LAN91C96_BASE 0x04000300 -#define CONFIG_LAN91C96_EXT_PHY - -/* - * NS16550 Configuration - */ - -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (1) -#define CONFIG_SYS_NS16550_CLK (48000000) /* can be 12M/32Khz or 48Mhz */ -#define CONFIG_SYS_NS16550_COM1 0xfffb0000 /* uart1, bluetooth uart - * on perseus */ - -/* - * select serial console configuration - */ - -#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on OMAP730 Perseus 2 */ - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 115200 - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_DHCP - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH - - -#include -#include - -#define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTARGS "mem=32M console=ttyS0,115200n8 noinitrd root=/dev/nfs rw ip=bootp" - -#define CONFIG_LOADADDR 0x10000000 - -#define CONFIG_ETHADDR -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 192.168.0.23 -#define CONFIG_SERVERIP 192.150.0.100 -#define CONFIG_BOOTFILE "uImage" /* File to load */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 115200 /* Speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 1 /* Which serial port to use */ -#endif - -/* - * Miscellaneous configurable options - */ - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "OMAP730 P2 # " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */ - -/* The OMAP730 has 3 general purpose MPU timers, they can be driven by - * the RefClk (12Mhz) or by DPLL1. This time is further subdivided by a - * local divisor. - */ -#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */ -#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */ -#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV)) - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ - -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ -#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ - -#if defined(CONFIG_CS0_BOOT) -#define PHYS_FLASH_1 0x0C000000 -#elif defined(CONFIG_CS3_BOOT) -#define PHYS_FLASH_1 0x00000000 -#else -#error Unknown Boot Chip-Select number -#endif - -#define PHYS_SRAM 0x20000000 - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define PHYS_FLASH_SIZE 0x02000000 /* 32MB */ -#define CONFIG_SYS_MAX_FLASH_SECT (259) /* max number of sectors on one chip */ -/* addr of environment */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x020000) - -/* timeout values are in ticks */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Erase */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Write */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */ -#define CONFIG_ENV_OFFSET 0x20000 /* environment starts here */ - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_SP_ADDR PHYS_SRAM - -#endif /* ! __CONFIG_H */