From: zachary <zhangzg@marvell.com>
Date: Fri, 28 Aug 2020 14:56:29 +0000 (+0200)
Subject: phy: marvell: a3700: add sata comphy on lane 2 with invert option
X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=7757c85199f57e71d5021670ff1d317e0c622f89;p=u-boot.git

phy: marvell: a3700: add sata comphy on lane 2 with invert option

- This patch moves sata phy powerup from dedicate phy to compphy
  and adds invert option for sata powerup routine.

Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53601
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
---

diff --git a/drivers/phy/marvell/comphy_a3700.c b/drivers/phy/marvell/comphy_a3700.c
index dc188c44e0..4606de6f48 100644
--- a/drivers/phy/marvell/comphy_a3700.c
+++ b/drivers/phy/marvell/comphy_a3700.c
@@ -273,16 +273,23 @@ static void reg_set_indirect(u32 reg, u16 data, u16 mask)
  *
  * return: 1 if PLL locked (OK), 0 otherwise (FAIL)
  */
-static int comphy_sata_power_up(void)
+static int comphy_sata_power_up(u32 invert)
 {
 	int ret;
+	u32 data = 0;
 
 	debug_enter();
 
 	/*
-	 * 0. Swap SATA TX lines
+	 * 0. Check the Polarity invert bits
 	 */
-	reg_set_indirect(vphy_sync_pattern_reg, bs_txd_inv, bs_txd_inv);
+	if (invert & PHY_POLARITY_TXD_INVERT)
+		data |= bs_txd_inv;
+
+	if (invert & PHY_POLARITY_RXD_INVERT)
+		data |= bs_rxd_inv;
+
+	reg_set_indirect(vphy_sync_pattern_reg, data, bs_txd_inv | bs_rxd_inv);
 
 	/*
 	 * 1. Select 40-bit data width width
@@ -924,22 +931,6 @@ void comphy_dedicated_phys_init(void)
 		}
 	}
 
-	node = fdt_node_offset_by_compatible(blob, -1,
-					     "marvell,armada-3700-ahci");
-	if (node > 0) {
-		if (fdtdec_get_is_enabled(blob, node)) {
-			ret = comphy_sata_power_up();
-			if (!ret)
-				printf("Failed to initialize SATA PHY\n");
-			else
-				debug("SATA PHY init succeed\n");
-		} else {
-			debug("SATA node is disabled\n");
-		}
-	}  else {
-		debug("No SATA node in DT\n");
-	}
-
 	node = fdt_node_offset_by_compatible(blob, -1,
 					     "marvell,armada-8k-sdhci");
 	if (node <= 0) {
@@ -1007,6 +998,10 @@ int comphy_a3700_init(struct chip_serdes_phy_config *chip_cfg,
 						    comphy_map->invert);
 			break;
 
+		case PHY_TYPE_SATA0:
+			ret = comphy_sata_power_up(comphy_map->invert);
+			break;
+
 		default:
 			debug("Unknown SerDes type, skip initialize SerDes %d\n",
 			      lane);