From: Sebastian Reichel <sebastian.reichel@collabora.com>
Date: Mon, 14 Dec 2020 23:41:57 +0000 (+0100)
Subject: board: ge: bx50v3: cleanup phy config
X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=717bf50f4b362c1f4fac5ac9f030fab5bed9cf65;p=u-boot.git

board: ge: bx50v3: cleanup phy config

The current PHY rework does the following things:

1. Configure 125MHz clock
2. Setup the TX clock delay (RX is enabled by default),
3. Setup reserved bits to avoid voltage peak

The clock delays are nowadays already configured by the
PHY driver (in ar803x_delay_config). The code for that
can simply be dropped. The clock speed can also be
configured by the PHY driver by adding the device tree
property "qca,clk-out-frequency".

What is left is setting up the undocumented reserved bits
to avoid the voltage peak problem. I slightly improved its
documentation while updating the board's PHY rework code.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---

diff --git a/arch/arm/dts/imx6q-ba16.dtsi b/arch/arm/dts/imx6q-ba16.dtsi
index 7d8f61f2fd..9da2bb6e86 100644
--- a/arch/arm/dts/imx6q-ba16.dtsi
+++ b/arch/arm/dts/imx6q-ba16.dtsi
@@ -174,6 +174,17 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
 	status = "okay";
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@4 {
+			reg = <4>;
+			qca,clk-out-frequency = <125000000>;
+		};
+	};
 };
 
 &hdmi {
diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c
index a3ae037a82..3ea9425fd1 100644
--- a/board/ge/bx50v3/bx50v3.c
+++ b/board/ge/bx50v3/bx50v3.c
@@ -47,6 +47,10 @@ DECLARE_GLOBAL_DATA_PTR;
 #define VPD_PRODUCT_B650 2
 #define VPD_PRODUCT_B450 3
 
+#define AR8033_DBG_REG_ADDR		0x1d
+#define AR8033_DBG_REG_DATA		0x1e
+#define AR8033_SERDES_REG		0x5
+
 static int productid;  /* Default to generic. */
 static struct vpd_cache vpd;
 
@@ -61,31 +65,16 @@ int dram_init(void)
 	return 0;
 }
 
-static int mx6_rgmii_rework(struct phy_device *phydev)
-{
-	/* Configure AR8033 to ouput a 125MHz clk from CLK_25M */
-	/* set device address 0x7 */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
-	/* offset 0x8016: CLK_25M Clock Select */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
-	/* enable register write, no post increment, address 0x7 */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
-	/* set to 125 MHz from local PLL source */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18);
-
-	/* rgmii tx clock delay enable */
-	/* set debug port address: SerDes Test and System Mode Control */
-	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
-	/* enable rgmii tx clock delay */
-	/* set the reserved bits to avoid board specific voltage peak issue*/
-	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3D47);
-
-	return 0;
-}
-
 int board_phy_config(struct phy_device *phydev)
 {
-	mx6_rgmii_rework(phydev);
+	/*
+	 * Set reserved bits to avoid board specific voltage peak issue. The
+	 * value is a magic number provided directly by Qualcomm. Note, that
+	 * PHY driver will take control of BIT(8) in this register to control
+	 * TX clock delay, so we do not initialize that bit here.
+	 */
+	phy_write(phydev, MDIO_DEVAD_NONE, AR8033_DBG_REG_ADDR, AR8033_SERDES_REG);
+	phy_write(phydev, MDIO_DEVAD_NONE, AR8033_DBG_REG_DATA, 0x3c47);
 
 	if (phydev->drv->config)
 		phydev->drv->config(phydev);