From: Ruchika Gupta Date: Mon, 17 Apr 2017 12:37:17 +0000 (+0530) Subject: arm: ls1043ardb: Add SD secure boot target X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=70f9661ca9130c446c146f582046024eddaaee31;p=u-boot.git arm: ls1043ardb: Add SD secure boot target - Add SD secure boot target for ls1043ardb. - Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream ID and corresponding stream ID in SMMU. - Change the u-boot size defined by a macro for copying the main U-Boot by SPL to also include the u-boot Secure Boot header size as header is appended to u-boot image. So header will also be copied from SD to DDR. - CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM (128K) where 32K are reserved for use by boot ROM and 6K for secure boto header. - Error messages during SPL boot are limited to error code numbers instead of strings to reduce the size of SPL image. Signed-off-by: Vinitha Pillai-B57223 Signed-off-by: Sumit Garg Signed-off-by: Ruchika Gupta Reviewed-by: York Sun --- diff --git a/arch/arm/cpu/armv8/fsl-layerscape/spl.c b/arch/arm/cpu/armv8/fsl-layerscape/spl.c index 73a8680741..dfacf98e88 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/spl.c +++ b/arch/arm/cpu/armv8/fsl-layerscape/spl.c @@ -41,6 +41,24 @@ u32 spl_boot_mode(const u32 boot_device) } #ifdef CONFIG_SPL_BUILD + +void spl_board_init(void) +{ +#if defined(CONFIG_SECURE_BOOT) && defined(CONFIG_FSL_LSCH2) + /* + * In case of Secure Boot, the IBR configures the SMMU + * to allow only Secure transactions. + * SMMU must be reset in bypass mode. + * Set the ClientPD bit and Clear the USFCFG Bit + */ + u32 val; + val = (in_le32(SMMU_SCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK); + out_le32(SMMU_SCR0, val); + val = (in_le32(SMMU_NSCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK); + out_le32(SMMU_NSCR0, val); +#endif +} + void board_init_f(ulong dummy) { /* Clear global data */ diff --git a/arch/arm/include/asm/fsl_secure_boot.h b/arch/arm/include/asm/fsl_secure_boot.h index 558dc62cc7..1ca5f42ed6 100644 --- a/arch/arm/include/asm/fsl_secure_boot.h +++ b/arch/arm/include/asm/fsl_secure_boot.h @@ -27,10 +27,11 @@ #define CONFIG_SPL_UBOOT_KEY_HASH NULL #endif /* ifdef CONFIG_SPL_BUILD */ +#define CONFIG_KEY_REVOCATION + #ifndef CONFIG_SPL_BUILD #define CONFIG_CMD_BLOB #define CONFIG_CMD_HASH -#define CONFIG_KEY_REVOCATION #ifndef CONFIG_SYS_RAMBOOT /* The key used for verification of next level images * is picked up from an Extension Table which has @@ -87,7 +88,11 @@ /* For SD boot address and size are assigned in terms of sector * offset and no. of sectors respectively. */ -#define CONFIG_BS_HDR_ADDR_DEVICE 0x00000900 +#if defined(CONFIG_LS1043A) +#define CONFIG_BS_HDR_ADDR_DEVICE 0x00000920 +#else +#define CONFIG_BS_HDR_ADDR_DEVICE 0x00000900 +#endif #define CONFIG_BS_ADDR_DEVICE 0x00000940 #define CONFIG_BS_HDR_SIZE 0x00000010 #define CONFIG_BS_SIZE 0x00000008 diff --git a/board/freescale/common/fsl_validate.c b/board/freescale/common/fsl_validate.c index 7396aa2f69..125655a37a 100644 --- a/board/freescale/common/fsl_validate.c +++ b/board/freescale/common/fsl_validate.c @@ -393,6 +393,7 @@ static void fsl_secboot_bootscript_parse_failure(void) */ void fsl_secboot_handle_error(int error) { +#ifndef CONFIG_SPL_BUILD const struct fsl_secboot_errcode *e; for (e = fsl_secboot_errcodes; e->errcode != ERROR_ESBC_CLIENT_MAX; @@ -400,6 +401,9 @@ void fsl_secboot_handle_error(int error) if (e->errcode == error) printf("ERROR :: %x :: %s\n", error, e->name); } +#else + printf("ERROR :: %x\n", error); +#endif /* If Boot Mode is secure, transition the SNVS state and issue * reset based on type of failure and ITS setting. diff --git a/board/freescale/ls1043ardb/MAINTAINERS b/board/freescale/ls1043ardb/MAINTAINERS index 0503a3fcc9..8b69892bbb 100644 --- a/board/freescale/ls1043ardb/MAINTAINERS +++ b/board/freescale/ls1043ardb/MAINTAINERS @@ -12,3 +12,4 @@ LS1043A_SECURE_BOOT BOARD M: Ruchika Gupta S: Maintained F: configs/ls1043ardb_SECURE_BOOT_defconfig +F: configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig diff --git a/configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig b/configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig new file mode 100644 index 0000000000..3f35d6493f --- /dev/null +++ b/configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig @@ -0,0 +1,57 @@ +CONFIG_ARM=y +CONFIG_TARGET_LS1043ARDB=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_ENV_SUPPORT=y +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y +CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb" +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SD_BOOT" +CONFIG_SECURE_BOOT=y +CONFIG_SD_BOOT=y +CONFIG_BOOTDELAY=10 +CONFIG_SPL=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x110 +CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y +CONFIG_HUSH_PARSER=y +CONFIG_CMD_GPT=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SF=y +CONFIG_CMD_I2C=y +CONFIG_CMD_USB=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_PXE=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_FAT=y +# CONFIG_SPL_EFI_PARTITION is not set +CONFIG_OF_CONTROL=y +CONFIG_DM=y +CONFIG_SPL_DM=y +CONFIG_MTD_NOR_FLASH=y +CONFIG_SPI_FLASH=y +CONFIG_NETDEVICES=y +CONFIG_E1000=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCIE_LAYERSCAPE=y +CONFIG_SYS_NS16550=y +CONFIG_DM_SPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_STORAGE=y +CONFIG_RSA=y +CONFIG_SPL_RSA=y +CONFIG_SPL_CRYPTO_SUPPORT=y +CONFIG_SPL_HASH_SUPPORT=y diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h index 23b7ef7b82..c63c5e3403 100644 --- a/include/configs/ls1043a_common.h +++ b/include/configs/ls1043a_common.h @@ -71,7 +71,7 @@ #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" #define CONFIG_SPL_TEXT_BASE 0x10000000 -#define CONFIG_SPL_MAX_SIZE 0x1d000 +#define CONFIG_SPL_MAX_SIZE 0x17000 #define CONFIG_SPL_STACK 0x1001e000 #define CONFIG_SPL_PAD_TO 0x1d000 @@ -80,7 +80,19 @@ #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 -#define CONFIG_SYS_MONITOR_LEN 0xa0000 + +#ifdef CONFIG_SECURE_BOOT +#define CONFIG_U_BOOT_HDR_SIZE (16 << 10) +/* + * HDR would be appended at end of image and copied to DDR along + * with U-Boot image. Here u-boot max. size is 512K. So if binary + * size increases then increase this size in case of secure boot as + * it uses raw u-boot image instead of fit image. + */ +#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE) +#else +#define CONFIG_SYS_MONITOR_LEN 0x100000 +#endif /* ifdef CONFIG_SECURE_BOOT */ #endif /* NAND SPL */