From: Matthias Fuchs Date: Sun, 24 Jun 2007 15:41:21 +0000 (+0200) Subject: ppc4xx: Maintenance patch for esd's CPCI405 derivats X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=6f35c53166213c24a5a0e2390ed861136ff73870;p=u-boot.git ppc4xx: Maintenance patch for esd's CPCI405 derivats -add pci_pre_init() for pci interrupt fixup code -disable phy sleep mode via reset_phy() function -use correct io accessors -cleanup Signed-off-by: Matthias Fuchs --- diff --git a/board/esd/cpci405/cpci405.c b/board/esd/cpci405/cpci405.c index f80361081a..263b75d3a1 100644 --- a/board/esd/cpci405/cpci405.c +++ b/board/esd/cpci405/cpci405.c @@ -23,9 +23,11 @@ #include #include +#include #include #include #include +#include DECLARE_GLOBAL_DATA_PTR; @@ -179,11 +181,15 @@ int board_early_init_f (void) mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */ mtdcr(uicer, 0x00000000); /* disable all ints */ mtdcr(uiccr, 0x00000000); /* set all to be non-critical*/ +#ifdef CONFIG_CPCI405_6U if (cpci405_version() == 3) { mtdcr(uicpr, 0xFFFFFF99); /* set int polarities */ } else { mtdcr(uicpr, 0xFFFFFF81); /* set int polarities */ } +#else + mtdcr(uicpr, 0xFFFFFF81); /* set int polarities */ +#endif mtdcr(uictr, 0x10000000); /* set int trigger levels */ mtdcr(uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority*/ mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */ @@ -227,10 +233,10 @@ int cpci405_version(void) */ cntrl0Reg = mfdcr(cntrl0); mtdcr(cntrl0, cntrl0Reg | 0x03000000); - out32(GPIO0_ODR, in32(GPIO0_ODR) & ~0x00180000); - out32(GPIO0_TCR, in32(GPIO0_TCR) & ~0x00180000); + out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x00180000); + out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x00180000); udelay(1000); /* wait some time before reading input */ - value = in32(GPIO0_IR) & 0x00180000; /* get config bits */ + value = in_be32((void*)GPIO0_IR) & 0x00180000; /* get config bits */ /* * Restore GPIO settings @@ -245,7 +251,7 @@ int cpci405_version(void) /* CS2==0 && CS3==1 -> version 2 */ return 2; case 0x00100000: - /* CS2==1 && CS3==0 -> version 3 */ + /* CS2==1 && CS3==0 -> version 3 or 6U board */ return 3; case 0x00000000: /* CS2==0 && CS3==0 -> version 4 */ @@ -283,7 +289,6 @@ int misc_init_r (void) * On CPCI-405 version 2 the environment is saved in eeprom! * FPGA can be gzip compressed (malloc) and booted this late. */ - if (cpci405_version() >= 2) { /* * Setup GPIO pins (CS6+CS7 as GPIO) @@ -354,6 +359,7 @@ int misc_init_r (void) SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA); udelay(1000); /* wait 1ms */ +#ifdef CONFIG_CPCI405_6U if (cpci405_version() == 3) { volatile unsigned short *fpga_mode = (unsigned short *)CFG_FPGA_BASE_ADDR; volatile unsigned char *leds = (unsigned char *)CFG_LED_ADDR; @@ -375,6 +381,7 @@ int misc_init_r (void) udelay(100); *fpga_mode &= ~(CFG_FPGA_MODE_DUART_RESET); } +#endif } else { puts("\n*** U-Boot Version does not match Board Version!\n"); @@ -493,12 +500,6 @@ int checkboard (void) #endif putc ('\n'); - - /* - * Disable sleep mode in LXT971 - */ - lxt971_no_sleep(); - return 0; } @@ -511,24 +512,22 @@ long int initdram (int board_type) mtdcr(memcfga, mem_mb0cf); val = mfdcr(memcfgd); -#if 0 - printf("\nmb0cf=%x\n", val); /* test-only */ - printf("strap=%x\n", mfdcr(strap)); /* test-only */ -#endif - return (4*1024*1024 << ((val & 0x000e0000) >> 17)); } -/* ------------------------------------------------------------------------- */ -int testdram (void) +void reset_phy(void) { - /* TODO: XXX XXX XXX */ - printf ("test: 16 MB - ok\n"); +#ifdef CONFIG_LXT971_NO_SLEEP - return (0); + /* + * Disable sleep mode in LXT971 + */ + lxt971_no_sleep(); +#endif } + /* ------------------------------------------------------------------------- */ #ifdef CONFIG_CPCI405_VER2 @@ -552,6 +551,41 @@ void ide_set_reset(int on) #endif /* CONFIG_CPCI405_VER2 */ +#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) +void cpci405_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev) +{ + unsigned char int_line = 0xff; + + /* + * Write pci interrupt line register (cpci405 specific) + */ + switch (PCI_DEV(dev) & 0x03) { + case 0: + int_line = 27 + 2; + break; + case 1: + int_line = 27 + 3; + break; + case 2: + int_line = 27 + 0; + break; + case 3: + int_line = 27 + 1; + break; + } + + pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, int_line); +} + +int pci_pre_init(struct pci_controller *hose) +{ + hose->fixup_irq = cpci405_pci_fixup_irq; + return 1; +} +#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */ + + + #ifdef CONFIG_CPCI405AB #define ONE_WIRE_CLEAR (*(volatile unsigned short *)(CFG_FPGA_BASE_ADDR + CFG_FPGA_MODE) \ diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h index 047e2f1eef..67f7581130 100644 --- a/include/configs/CPCI405.h +++ b/include/configs/CPCI405.h @@ -55,6 +55,10 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ + +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 #define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ CONFIG_BOOTP_DNS | \ @@ -139,6 +143,7 @@ #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI /* include pci support */ +#define CFG_PCI_PRE_INIT /* pci interrupt mapping etc. */ #define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ /* resource configuration */ diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h index d756f447f7..8abdbdc6df 100644 --- a/include/configs/CPCI4052.h +++ b/include/configs/CPCI4052.h @@ -37,6 +37,7 @@ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ #define CONFIG_CPCI405 1 /* ...on a CPCI405 board */ #define CONFIG_CPCI405_VER2 1 /* ...version 2 */ +#undef CONFIG_CPCI405_6U /* enable this for 6U boards */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ @@ -56,6 +57,10 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ + +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 #define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ @@ -166,6 +171,7 @@ #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI /* include pci support */ +#define CFG_PCI_PRE_INIT /* pci interrupt mapping etc. */ #define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ /* resource configuration */ diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h index 852d94a410..ab6d1168f1 100644 --- a/include/configs/CPCI405AB.h +++ b/include/configs/CPCI405AB.h @@ -57,6 +57,10 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ + +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 #define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ @@ -150,6 +154,7 @@ #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI /* include pci support */ +#define CFG_PCI_PRE_INIT /* pci interrupt mapping etc. */ #define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ /* resource configuration */ diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h index 2260327c3f..42ec0801ad 100644 --- a/include/configs/CPCI405DT.h +++ b/include/configs/CPCI405DT.h @@ -56,6 +56,10 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ + +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 #define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ @@ -171,6 +175,7 @@ #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI /* include pci support */ +#define CFG_PCI_PRE_INIT /* pci interrupt mapping etc. */ #define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ /* resource configuration */