From: Heiko Schocher Date: Thu, 6 Feb 2020 08:48:16 +0000 (+0100) Subject: net, qe: add DM support for QE UEC ethernet X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=6e31c62a175ca24f74b89a684c82cbb4bf423f16;p=u-boot.git net, qe: add DM support for QE UEC ethernet add DM/DTS support for the UEC ethernet on QUICC Engine Block. Signed-off-by: Heiko Schocher Patch-cc: Mario Six Patch-cc: Qiang Zhao Patch-cc: Holger Brunck Patch-cc: Madalin Bucur Series-changes: 3 - revert: commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled") as now qe works with DM and DM_ETH support. - fix mailaddress from Holger Series-changes: 2 - add comments from Qiang Zhao: - add device node documentation - I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c because using drivers/net/fsl_mdio.c leads in none existent udevice mdio@3320 instead boards with DM ETH support should use now this driver. - remove RFC tag Commit-notes: - I let the old none DM based implementation in code so boards should work with old implementation. This Code should be removed if all boards are converted to DM/DTS. - add the DM based qe uec driver under drivers/net/qe - Therefore copied the files uccf.c uccf.h uec.h from drivers/qe. So there are a lot of Codingstyle problems currently. I fix them in next version if this RFC patch is OK or it needs some changes. - The dm based driver code is now under drivers/net/qe/dm_qe_uec.c Used a lot of functions from drivers/qe/uec.c - seperated the PHY specific code into seperate file drivers/net/qe/dm_qe_uec_phy.c END --- diff --git a/doc/device-tree-bindings/soc/fsl/cpm_qe/qe/ucc.txt b/doc/device-tree-bindings/soc/fsl/cpm_qe/qe/ucc.txt new file mode 100644 index 0000000000..2758f86437 --- /dev/null +++ b/doc/device-tree-bindings/soc/fsl/cpm_qe/qe/ucc.txt @@ -0,0 +1,53 @@ +* UCC (Unified Communications Controllers) + +Required properties: +- compatible : ucc_geth +- cell-index : the ucc number(1-8), corresponding to UCCx in UM. +- reg : Offset and length of the register set for the device +- rx-clock-name: the UCC receive clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +- tx-clock-name: the UCC transmit clock source + "none": clock source is disabled + "brg1" through "brg16": clock source is BRG1-BRG16, respectively + "clk1" through "clk24": clock source is CLK1-CLK24, respectively +The following two properties are deprecated. rx-clock has been replaced +with rx-clock-name, and tx-clock has been replaced with tx-clock-name. +Drivers that currently use the deprecated properties should continue to +do so, in order to support older device trees, but they should be updated +to check for the new properties first. +- rx-clock : represents the UCC receive clock source. + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. +- tx-clock: represents the UCC transmit clock source; + 0x00 : clock source is disabled; + 0x1~0x10 : clock source is BRG1~BRG16 respectively; + 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively. +- phy-handle : The phandle for the PHY connected to this controller. +- phy-connection-type : a string naming the controller/PHY interface type, + i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal + Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only), + "tbi", or "rtbi". +- pio-handle : The phandle for the Parallel I/O port configuration. + +Deprecated properties: +- device-id : the ucc number(1-8), corresponding to UCCx in UM. + you should use cell-index + +Example: + ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <2000 200>; + interrupts = ; + interrupt-parent = <700>; + mac-address = [ 00 04 9f 00 23 23 ]; + rx-clock = "none"; + tx-clock = "clk9"; + phy-handle = <212000>; + phy-connection-type = "gmii"; + pio-handle = <140001>; + }; diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 039f9fb058..a0d2d21a55 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -432,6 +432,8 @@ config PCNET This driver supports AMD PCnet series fast ethernet family of PCI chipsets/adapters. +source "drivers/net/qe/Kconfig" + config RTL8139 bool "Realtek 8139 series Ethernet controller driver" help diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 1ecdc40b8f..03f01921ea 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -78,6 +78,7 @@ obj-$(CONFIG_VSC9953) += vsc9953.o obj-$(CONFIG_PIC32_ETH) += pic32_mdio.o pic32_eth.o obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o obj-$(CONFIG_FSL_PFE) += pfe_eth/ +obj-y += qe/ obj-$(CONFIG_SNI_AVE) += sni_ave.o obj-y += ti/ obj-$(CONFIG_MEDIATEK_ETH) += mtk_eth.o diff --git a/drivers/net/qe/Kconfig b/drivers/net/qe/Kconfig new file mode 100644 index 0000000000..dec88dea2a --- /dev/null +++ b/drivers/net/qe/Kconfig @@ -0,0 +1,9 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2020 Heiko Schocher + +config QE_UEC + bool "NXP QE UEC Ethernet controller" + depends on DM_ETH + help + This driver supports the NXP QE UEC ethernet controller diff --git a/drivers/net/qe/Makefile b/drivers/net/qe/Makefile new file mode 100644 index 0000000000..7d84757c17 --- /dev/null +++ b/drivers/net/qe/Makefile @@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2020 Heiko Schocher + +obj-$(CONFIG_QE_UEC) += dm_qe_uec.o dm_qe_uec_phy.o uccf.o diff --git a/drivers/net/qe/dm_qe_uec.c b/drivers/net/qe/dm_qe_uec.c new file mode 100644 index 0000000000..3482b3ff17 --- /dev/null +++ b/drivers/net/qe/dm_qe_uec.c @@ -0,0 +1,1167 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * QE UEC ethernet controller driver + * + * based on drivers/qe/uec.c from NXP + * + * Copyright (C) 2020 Heiko Schocher + */ + +#include +#include +#include +#include +#include +#include + +#include "dm_qe_uec.h" + +#define QE_UEC_DRIVER_NAME "ucc_geth" + +/* Default UTBIPAR SMI address */ +#ifndef CONFIG_UTBIPAR_INIT_TBIPA +#define CONFIG_UTBIPAR_INIT_TBIPA 0x1F +#endif + +static int uec_mac_enable(struct uec_priv *uec, comm_dir_e mode) +{ + uec_t *uec_regs; + u32 maccfg1; + + uec_regs = uec->uec_regs; + maccfg1 = in_be32(&uec_regs->maccfg1); + + if (mode & COMM_DIR_TX) { + maccfg1 |= MACCFG1_ENABLE_TX; + out_be32(&uec_regs->maccfg1, maccfg1); + uec->mac_tx_enabled = 1; + } + + if (mode & COMM_DIR_RX) { + maccfg1 |= MACCFG1_ENABLE_RX; + out_be32(&uec_regs->maccfg1, maccfg1); + uec->mac_rx_enabled = 1; + } + + return 0; +} + +static int uec_mac_disable(struct uec_priv *uec, comm_dir_e mode) +{ + uec_t *uec_regs; + u32 maccfg1; + + uec_regs = uec->uec_regs; + maccfg1 = in_be32(&uec_regs->maccfg1); + + if (mode & COMM_DIR_TX) { + maccfg1 &= ~MACCFG1_ENABLE_TX; + out_be32(&uec_regs->maccfg1, maccfg1); + uec->mac_tx_enabled = 0; + } + + if (mode & COMM_DIR_RX) { + maccfg1 &= ~MACCFG1_ENABLE_RX; + out_be32(&uec_regs->maccfg1, maccfg1); + uec->mac_rx_enabled = 0; + } + + return 0; +} + +static int uec_restart_tx(struct uec_priv *uec) +{ + struct uec_inf *ui = uec->uec_info; + u32 cecr_subblock; + + cecr_subblock = ucc_fast_get_qe_cr_subblock(ui->uf_info.ucc_num); + qe_issue_cmd(QE_RESTART_TX, cecr_subblock, + (u8)QE_CR_PROTOCOL_ETHERNET, 0); + + uec->grace_stopped_tx = 0; + + return 0; +} + +static int uec_restart_rx(struct uec_priv *uec) +{ + struct uec_inf *ui = uec->uec_info; + u32 cecr_subblock; + + cecr_subblock = ucc_fast_get_qe_cr_subblock(ui->uf_info.ucc_num); + qe_issue_cmd(QE_RESTART_RX, cecr_subblock, + (u8)QE_CR_PROTOCOL_ETHERNET, 0); + + uec->grace_stopped_rx = 0; + + return 0; +} + +static int uec_open(struct uec_priv *uec, comm_dir_e mode) +{ + struct ucc_fast_priv *uccf; + + uccf = uec->uccf; + + /* check if the UCC number is in range. */ + if (uec->uec_info->uf_info.ucc_num >= UCC_MAX_NUM) { + printf("%s: ucc_num out of range.\n", __func__); + return -EINVAL; + } + + /* Enable MAC */ + uec_mac_enable(uec, mode); + + /* Enable UCC fast */ + ucc_fast_enable(uccf, mode); + + /* RISC microcode start */ + if ((mode & COMM_DIR_TX) && uec->grace_stopped_tx) + uec_restart_tx(uec); + + if ((mode & COMM_DIR_RX) && uec->grace_stopped_rx) + uec_restart_rx(uec); + + return 0; +} + +static int uec_set_mac_if_mode(struct uec_priv *uec) +{ + struct uec_inf *uec_info = uec->uec_info; + phy_interface_t enet_if_mode; + uec_t *uec_regs; + u32 upsmr; + u32 maccfg2; + + uec_regs = uec->uec_regs; + enet_if_mode = uec_info->enet_interface_type; + + maccfg2 = in_be32(&uec_regs->maccfg2); + maccfg2 &= ~MACCFG2_INTERFACE_MODE_MASK; + + upsmr = in_be32(&uec->uccf->uf_regs->upsmr); + upsmr &= ~(UPSMR_RPM | UPSMR_TBIM | UPSMR_R10M | UPSMR_RMM); + + switch (uec_info->speed) { + case SPEED_10: + maccfg2 |= MACCFG2_INTERFACE_MODE_NIBBLE; + switch (enet_if_mode) { + case PHY_INTERFACE_MODE_MII: + break; + case PHY_INTERFACE_MODE_RGMII: + upsmr |= (UPSMR_RPM | UPSMR_R10M); + break; + case PHY_INTERFACE_MODE_RMII: + upsmr |= (UPSMR_R10M | UPSMR_RMM); + break; + default: + return -EINVAL; + } + break; + case SPEED_100: + maccfg2 |= MACCFG2_INTERFACE_MODE_NIBBLE; + switch (enet_if_mode) { + case PHY_INTERFACE_MODE_MII: + break; + case PHY_INTERFACE_MODE_RGMII: + upsmr |= UPSMR_RPM; + break; + case PHY_INTERFACE_MODE_RMII: + upsmr |= UPSMR_RMM; + break; + default: + return -EINVAL; + } + break; + case SPEED_1000: + maccfg2 |= MACCFG2_INTERFACE_MODE_BYTE; + switch (enet_if_mode) { + case PHY_INTERFACE_MODE_GMII: + break; + case PHY_INTERFACE_MODE_TBI: + upsmr |= UPSMR_TBIM; + break; + case PHY_INTERFACE_MODE_RTBI: + upsmr |= (UPSMR_RPM | UPSMR_TBIM); + break; + case PHY_INTERFACE_MODE_RGMII_RXID: + case PHY_INTERFACE_MODE_RGMII_TXID: + case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII: + upsmr |= UPSMR_RPM; + break; + case PHY_INTERFACE_MODE_SGMII: + upsmr |= UPSMR_SGMM; + break; + default: + return -EINVAL; + } + break; + default: + return -EINVAL; + } + + out_be32(&uec_regs->maccfg2, maccfg2); + out_be32(&uec->uccf->uf_regs->upsmr, upsmr); + + return 0; +} + +static int qe_uec_start(struct udevice *dev) +{ + struct qe_uec_priv *priv = dev_get_priv(dev); + struct uec_priv *uec = priv->uec; + struct phy_device *phydev = priv->phydev; + struct uec_inf *uec_info = uec->uec_info; + int err; + + if (!phydev) + return -ENODEV; + + /* Setup MAC interface mode */ + genphy_update_link(phydev); + genphy_parse_link(phydev); + uec_info->speed = phydev->speed; + uec_set_mac_if_mode(uec); + + err = uec_open(uec, COMM_DIR_RX_AND_TX); + if (err) { + printf("%s: cannot enable UEC device\n", dev->name); + return -EINVAL; + } + + return (phydev->link ? 0 : -EINVAL); +} + +static int qe_uec_send(struct udevice *dev, void *packet, int length) +{ + struct qe_uec_priv *priv = dev_get_priv(dev); + struct uec_priv *uec = priv->uec; + struct ucc_fast_priv *uccf = uec->uccf; + struct buffer_descriptor *bd; + u16 status; + int i; + int result = 0; + + uccf = uec->uccf; + bd = uec->tx_bd; + + /* Find an empty TxBD */ + for (i = 0; BD_STATUS(bd) & TX_BD_READY; i++) { + if (i > 0x100000) { + printf("%s: tx buffer not ready\n", dev->name); + return result; + } + } + + /* Init TxBD */ + BD_DATA_SET(bd, packet); + BD_LENGTH_SET(bd, length); + status = BD_STATUS(bd); + status &= BD_WRAP; + status |= (TX_BD_READY | TX_BD_LAST); + BD_STATUS_SET(bd, status); + + /* Tell UCC to transmit the buffer */ + ucc_fast_transmit_on_demand(uccf); + + /* Wait for buffer to be transmitted */ + for (i = 0; BD_STATUS(bd) & TX_BD_READY; i++) { + if (i > 0x100000) { + printf("%s: tx error\n", dev->name); + return result; + } + } + + /* Ok, the buffer be transimitted */ + BD_ADVANCE(bd, status, uec->p_tx_bd_ring); + uec->tx_bd = bd; + result = 1; + + return result; +} + +/* + * Receive frame: + * - wait for the next BD to get ready bit set + * - clean up the descriptor + * - move on and indicate to HW that the cleaned BD is available for Rx + */ +static int qe_uec_recv(struct udevice *dev, int flags, uchar **packetp) +{ + struct qe_uec_priv *priv = dev_get_priv(dev); + struct uec_priv *uec = priv->uec; + struct buffer_descriptor *bd; + u16 status; + u16 len = 0; + u8 *data; + + *packetp = memalign(ARCH_DMA_MINALIGN, MAX_RXBUF_LEN); + if (*packetp == 0) { + printf("%s: error allocating packetp\n", __func__); + return -ENOMEM; + } + + bd = uec->rx_bd; + status = BD_STATUS(bd); + + while (!(status & RX_BD_EMPTY)) { + if (!(status & RX_BD_ERROR)) { + data = BD_DATA(bd); + len = BD_LENGTH(bd); + memcpy(*packetp, (char *)data, len); + } else { + printf("%s: Rx error\n", dev->name); + } + status &= BD_CLEAN; + BD_LENGTH_SET(bd, 0); + BD_STATUS_SET(bd, status | RX_BD_EMPTY); + BD_ADVANCE(bd, status, uec->p_rx_bd_ring); + status = BD_STATUS(bd); + } + uec->rx_bd = bd; + + return len; +} + +static int uec_graceful_stop_tx(struct uec_priv *uec) +{ + ucc_fast_t *uf_regs; + u32 cecr_subblock; + u32 ucce; + + uf_regs = uec->uccf->uf_regs; + + /* Clear the grace stop event */ + out_be32(&uf_regs->ucce, UCCE_GRA); + + /* Issue host command */ + cecr_subblock = + ucc_fast_get_qe_cr_subblock(uec->uec_info->uf_info.ucc_num); + qe_issue_cmd(QE_GRACEFUL_STOP_TX, cecr_subblock, + (u8)QE_CR_PROTOCOL_ETHERNET, 0); + + /* Wait for command to complete */ + do { + ucce = in_be32(&uf_regs->ucce); + } while (!(ucce & UCCE_GRA)); + + uec->grace_stopped_tx = 1; + + return 0; +} + +static int uec_graceful_stop_rx(struct uec_priv *uec) +{ + u32 cecr_subblock; + u8 ack; + + if (!uec->p_rx_glbl_pram) { + printf("%s: No init rx global parameter\n", __func__); + return -EINVAL; + } + + /* Clear acknowledge bit */ + ack = uec->p_rx_glbl_pram->rxgstpack; + ack &= ~GRACEFUL_STOP_ACKNOWLEDGE_RX; + uec->p_rx_glbl_pram->rxgstpack = ack; + + /* Keep issuing cmd and checking ack bit until it is asserted */ + do { + /* Issue host command */ + cecr_subblock = + ucc_fast_get_qe_cr_subblock(uec->uec_info->uf_info.ucc_num); + qe_issue_cmd(QE_GRACEFUL_STOP_RX, cecr_subblock, + (u8)QE_CR_PROTOCOL_ETHERNET, 0); + ack = uec->p_rx_glbl_pram->rxgstpack; + } while (!(ack & GRACEFUL_STOP_ACKNOWLEDGE_RX)); + + uec->grace_stopped_rx = 1; + + return 0; +} + +static int uec_stop(struct uec_priv *uec, comm_dir_e mode) +{ + /* check if the UCC number is in range. */ + if (uec->uec_info->uf_info.ucc_num >= UCC_MAX_NUM) { + printf("%s: ucc_num out of range.\n", __func__); + return -EINVAL; + } + /* Stop any transmissions */ + if ((mode & COMM_DIR_TX) && !uec->grace_stopped_tx) + uec_graceful_stop_tx(uec); + + /* Stop any receptions */ + if ((mode & COMM_DIR_RX) && !uec->grace_stopped_rx) + uec_graceful_stop_rx(uec); + + /* Disable the UCC fast */ + ucc_fast_disable(uec->uccf, mode); + + /* Disable the MAC */ + uec_mac_disable(uec, mode); + + return 0; +} + +static void qe_uec_stop(struct udevice *dev) +{ + struct qe_uec_priv *priv = dev_get_priv(dev); + struct uec_priv *uec = priv->uec; + + uec_stop(uec, COMM_DIR_RX_AND_TX); +} + +static int qe_uec_set_hwaddr(struct udevice *dev) +{ + struct qe_uec_priv *priv = dev_get_priv(dev); + struct eth_pdata *pdata = dev_get_platdata(dev); + struct uec_priv *uec = priv->uec; + uec_t *uec_regs = uec->uec_regs; + uchar *mac = pdata->enetaddr; + u32 mac_addr1; + u32 mac_addr2; + + /* + * if a station address of 0x12345678ABCD, perform a write to + * MACSTNADDR1 of 0xCDAB7856, + * MACSTNADDR2 of 0x34120000 + */ + + mac_addr1 = (mac[5] << 24) | (mac[4] << 16) | + (mac[3] << 8) | (mac[2]); + out_be32(&uec_regs->macstnaddr1, mac_addr1); + + mac_addr2 = ((mac[1] << 24) | (mac[0] << 16)) & 0xffff0000; + out_be32(&uec_regs->macstnaddr2, mac_addr2); + + return 0; +} + +static int qe_uec_free_pkt(struct udevice *dev, uchar *packet, int length) +{ + if (packet) + free(packet); + + return 0; +} + +static const struct eth_ops qe_uec_eth_ops = { + .start = qe_uec_start, + .send = qe_uec_send, + .recv = qe_uec_recv, + .free_pkt = qe_uec_free_pkt, + .stop = qe_uec_stop, + .write_hwaddr = qe_uec_set_hwaddr, +}; + +static int uec_convert_threads_num(enum uec_num_of_threads threads_num, + int *threads_num_ret) +{ + int num_threads_numerica; + + switch (threads_num) { + case UEC_NUM_OF_THREADS_1: + num_threads_numerica = 1; + break; + case UEC_NUM_OF_THREADS_2: + num_threads_numerica = 2; + break; + case UEC_NUM_OF_THREADS_4: + num_threads_numerica = 4; + break; + case UEC_NUM_OF_THREADS_6: + num_threads_numerica = 6; + break; + case UEC_NUM_OF_THREADS_8: + num_threads_numerica = 8; + break; + default: + printf("%s: Bad number of threads value.", + __func__); + return -EINVAL; + } + + *threads_num_ret = num_threads_numerica; + + return 0; +} + +static void uec_init_tx_parameter(struct uec_priv *uec, int num_threads_tx) +{ + struct uec_inf *uec_info; + u32 end_bd; + u8 bmrx = 0; + int i; + + uec_info = uec->uec_info; + + /* Alloc global Tx parameter RAM page */ + uec->tx_glbl_pram_offset = + qe_muram_alloc(sizeof(struct uec_tx_global_pram), + UEC_TX_GLOBAL_PRAM_ALIGNMENT); + uec->p_tx_glbl_pram = (struct uec_tx_global_pram *) + qe_muram_addr(uec->tx_glbl_pram_offset); + + /* Zero the global Tx prameter RAM */ + memset(uec->p_tx_glbl_pram, 0, sizeof(struct uec_tx_global_pram)); + + /* Init global Tx parameter RAM */ + + /* TEMODER, RMON statistics disable, one Tx queue */ + out_be16(&uec->p_tx_glbl_pram->temoder, TEMODER_INIT_VALUE); + + /* SQPTR */ + uec->send_q_mem_reg_offset = + qe_muram_alloc(sizeof(struct uec_send_queue_qd), + UEC_SEND_QUEUE_QUEUE_DESCRIPTOR_ALIGNMENT); + uec->p_send_q_mem_reg = (struct uec_send_queue_mem_region *) + qe_muram_addr(uec->send_q_mem_reg_offset); + out_be32(&uec->p_tx_glbl_pram->sqptr, uec->send_q_mem_reg_offset); + + /* Setup the table with TxBDs ring */ + end_bd = (u32)uec->p_tx_bd_ring + (uec_info->tx_bd_ring_len - 1) + * SIZEOFBD; + out_be32(&uec->p_send_q_mem_reg->sqqd[0].bd_ring_base, + (u32)(uec->p_tx_bd_ring)); + out_be32(&uec->p_send_q_mem_reg->sqqd[0].last_bd_completed_address, + end_bd); + + /* Scheduler Base Pointer, we have only one Tx queue, no need it */ + out_be32(&uec->p_tx_glbl_pram->schedulerbasepointer, 0); + + /* TxRMON Base Pointer, TxRMON disable, we don't need it */ + out_be32(&uec->p_tx_glbl_pram->txrmonbaseptr, 0); + + /* TSTATE, global snooping, big endian, the CSB bus selected */ + bmrx = BMR_INIT_VALUE; + out_be32(&uec->p_tx_glbl_pram->tstate, ((u32)(bmrx) << BMR_SHIFT)); + + /* IPH_Offset */ + for (i = 0; i < MAX_IPH_OFFSET_ENTRY; i++) + out_8(&uec->p_tx_glbl_pram->iphoffset[i], 0); + + /* VTAG table */ + for (i = 0; i < UEC_TX_VTAG_TABLE_ENTRY_MAX; i++) + out_be32(&uec->p_tx_glbl_pram->vtagtable[i], 0); + + /* TQPTR */ + uec->thread_dat_tx_offset = + qe_muram_alloc(num_threads_tx * + sizeof(struct uec_thread_data_tx) + + 32 * (num_threads_tx == 1), + UEC_THREAD_DATA_ALIGNMENT); + + uec->p_thread_data_tx = (struct uec_thread_data_tx *) + qe_muram_addr(uec->thread_dat_tx_offset); + out_be32(&uec->p_tx_glbl_pram->tqptr, uec->thread_dat_tx_offset); +} + +static void uec_init_rx_parameter(struct uec_priv *uec, int num_threads_rx) +{ + u8 bmrx = 0; + int i; + struct uec_82xx_add_filtering_pram *p_af_pram; + + /* Allocate global Rx parameter RAM page */ + uec->rx_glbl_pram_offset = + qe_muram_alloc(sizeof(struct uec_rx_global_pram), + UEC_RX_GLOBAL_PRAM_ALIGNMENT); + uec->p_rx_glbl_pram = (struct uec_rx_global_pram *) + qe_muram_addr(uec->rx_glbl_pram_offset); + + /* Zero Global Rx parameter RAM */ + memset(uec->p_rx_glbl_pram, 0, sizeof(struct uec_rx_global_pram)); + + /* Init global Rx parameter RAM */ + /* + * REMODER, Extended feature mode disable, VLAN disable, + * LossLess flow control disable, Receive firmware statisic disable, + * Extended address parsing mode disable, One Rx queues, + * Dynamic maximum/minimum frame length disable, IP checksum check + * disable, IP address alignment disable + */ + out_be32(&uec->p_rx_glbl_pram->remoder, REMODER_INIT_VALUE); + + /* RQPTR */ + uec->thread_dat_rx_offset = + qe_muram_alloc(num_threads_rx * + sizeof(struct uec_thread_data_rx), + UEC_THREAD_DATA_ALIGNMENT); + uec->p_thread_data_rx = (struct uec_thread_data_rx *) + qe_muram_addr(uec->thread_dat_rx_offset); + out_be32(&uec->p_rx_glbl_pram->rqptr, uec->thread_dat_rx_offset); + + /* Type_or_Len */ + out_be16(&uec->p_rx_glbl_pram->typeorlen, 3072); + + /* RxRMON base pointer, we don't need it */ + out_be32(&uec->p_rx_glbl_pram->rxrmonbaseptr, 0); + + /* IntCoalescingPTR, we don't need it, no interrupt */ + out_be32(&uec->p_rx_glbl_pram->intcoalescingptr, 0); + + /* RSTATE, global snooping, big endian, the CSB bus selected */ + bmrx = BMR_INIT_VALUE; + out_8(&uec->p_rx_glbl_pram->rstate, bmrx); + + /* MRBLR */ + out_be16(&uec->p_rx_glbl_pram->mrblr, MAX_RXBUF_LEN); + + /* RBDQPTR */ + uec->rx_bd_qs_tbl_offset = + qe_muram_alloc(sizeof(struct uec_rx_bd_queues_entry) + + sizeof(struct uec_rx_pref_bds), + UEC_RX_BD_QUEUES_ALIGNMENT); + uec->p_rx_bd_qs_tbl = (struct uec_rx_bd_queues_entry *) + qe_muram_addr(uec->rx_bd_qs_tbl_offset); + + /* Zero it */ + memset(uec->p_rx_bd_qs_tbl, 0, sizeof(struct uec_rx_bd_queues_entry) + + sizeof(struct uec_rx_pref_bds)); + out_be32(&uec->p_rx_glbl_pram->rbdqptr, uec->rx_bd_qs_tbl_offset); + out_be32(&uec->p_rx_bd_qs_tbl->externalbdbaseptr, + (u32)uec->p_rx_bd_ring); + + /* MFLR */ + out_be16(&uec->p_rx_glbl_pram->mflr, MAX_FRAME_LEN); + /* MINFLR */ + out_be16(&uec->p_rx_glbl_pram->minflr, MIN_FRAME_LEN); + /* MAXD1 */ + out_be16(&uec->p_rx_glbl_pram->maxd1, MAX_DMA1_LEN); + /* MAXD2 */ + out_be16(&uec->p_rx_glbl_pram->maxd2, MAX_DMA2_LEN); + /* ECAM_PTR */ + out_be32(&uec->p_rx_glbl_pram->ecamptr, 0); + /* L2QT */ + out_be32(&uec->p_rx_glbl_pram->l2qt, 0); + /* L3QT */ + for (i = 0; i < 8; i++) + out_be32(&uec->p_rx_glbl_pram->l3qt[i], 0); + + /* VLAN_TYPE */ + out_be16(&uec->p_rx_glbl_pram->vlantype, 0x8100); + /* TCI */ + out_be16(&uec->p_rx_glbl_pram->vlantci, 0); + + /* Clear PQ2 style address filtering hash table */ + p_af_pram = (struct uec_82xx_add_filtering_pram *) + uec->p_rx_glbl_pram->addressfiltering; + + p_af_pram->iaddr_h = 0; + p_af_pram->iaddr_l = 0; + p_af_pram->gaddr_h = 0; + p_af_pram->gaddr_l = 0; +} + +static int uec_issue_init_enet_rxtx_cmd(struct uec_priv *uec, + int thread_tx, int thread_rx) +{ + struct uec_init_cmd_pram *p_init_enet_param; + u32 init_enet_param_offset; + struct uec_inf *uec_info; + struct ucc_fast_inf *uf_info; + int i; + int snum; + u32 off; + u32 entry_val; + u32 command; + u32 cecr_subblock; + + uec_info = uec->uec_info; + uf_info = &uec_info->uf_info; + + /* Allocate init enet command parameter */ + uec->init_enet_param_offset = + qe_muram_alloc(sizeof(struct uec_init_cmd_pram), 4); + init_enet_param_offset = uec->init_enet_param_offset; + uec->p_init_enet_param = (struct uec_init_cmd_pram *) + qe_muram_addr(uec->init_enet_param_offset); + + /* Zero init enet command struct */ + memset((void *)uec->p_init_enet_param, 0, + sizeof(struct uec_init_cmd_pram)); + + /* Init the command struct */ + p_init_enet_param = uec->p_init_enet_param; + p_init_enet_param->resinit0 = ENET_INIT_PARAM_MAGIC_RES_INIT0; + p_init_enet_param->resinit1 = ENET_INIT_PARAM_MAGIC_RES_INIT1; + p_init_enet_param->resinit2 = ENET_INIT_PARAM_MAGIC_RES_INIT2; + p_init_enet_param->resinit3 = ENET_INIT_PARAM_MAGIC_RES_INIT3; + p_init_enet_param->resinit4 = ENET_INIT_PARAM_MAGIC_RES_INIT4; + p_init_enet_param->largestexternallookupkeysize = 0; + + p_init_enet_param->rgftgfrxglobal |= ((u32)uec_info->num_threads_rx) + << ENET_INIT_PARAM_RGF_SHIFT; + p_init_enet_param->rgftgfrxglobal |= ((u32)uec_info->num_threads_tx) + << ENET_INIT_PARAM_TGF_SHIFT; + + /* Init Rx global parameter pointer */ + p_init_enet_param->rgftgfrxglobal |= uec->rx_glbl_pram_offset | + (u32)uec_info->risc_rx; + + /* Init Rx threads */ + for (i = 0; i < (thread_rx + 1); i++) { + snum = qe_get_snum(); + if (snum < 0) { + printf("%s can not get snum\n", __func__); + return -ENOMEM; + } + + if (i == 0) { + off = 0; + } else { + off = qe_muram_alloc(sizeof(struct uec_thread_rx_pram), + UEC_THREAD_RX_PRAM_ALIGNMENT); + } + + entry_val = ((u32)snum << ENET_INIT_PARAM_SNUM_SHIFT) | + off | (u32)uec_info->risc_rx; + p_init_enet_param->rxthread[i] = entry_val; + } + + /* Init Tx global parameter pointer */ + p_init_enet_param->txglobal = uec->tx_glbl_pram_offset | + (u32)uec_info->risc_tx; + + /* Init Tx threads */ + for (i = 0; i < thread_tx; i++) { + snum = qe_get_snum(); + if (snum < 0) { + printf("%s can not get snum\n", __func__); + return -ENOMEM; + } + + off = qe_muram_alloc(sizeof(struct uec_thread_tx_pram), + UEC_THREAD_TX_PRAM_ALIGNMENT); + + entry_val = ((u32)snum << ENET_INIT_PARAM_SNUM_SHIFT) | + off | (u32)uec_info->risc_tx; + p_init_enet_param->txthread[i] = entry_val; + } + + __asm__ __volatile__("sync"); + + /* Issue QE command */ + command = QE_INIT_TX_RX; + cecr_subblock = ucc_fast_get_qe_cr_subblock(uf_info->ucc_num); + qe_issue_cmd(command, cecr_subblock, (u8)QE_CR_PROTOCOL_ETHERNET, + init_enet_param_offset); + + return 0; +} + +static int uec_startup(struct udevice *dev) +{ + struct qe_uec_priv *priv = dev_get_priv(dev); + struct uec_priv *uec = priv->uec; + struct uec_inf *uec_info; + struct ucc_fast_inf *uf_info; + struct ucc_fast_priv *uccf; + ucc_fast_t *uf_regs; + uec_t *uec_regs; + int num_threads_tx; + int num_threads_rx; + u32 utbipar; + u32 length; + u32 align; + struct buffer_descriptor *bd; + u8 *buf; + int i; + + uec_info = uec->uec_info; + uf_info = &uec_info->uf_info; + + /* Check if Rx BD ring len is illegal */ + if (uec_info->rx_bd_ring_len < UEC_RX_BD_RING_SIZE_MIN || + uec_info->rx_bd_ring_len % UEC_RX_BD_RING_SIZE_ALIGNMENT) { + printf("%s: Rx BD ring len must be multiple of 4, and > 8.\n", + __func__); + return -EINVAL; + } + + /* Check if Tx BD ring len is illegal */ + if (uec_info->tx_bd_ring_len < UEC_TX_BD_RING_SIZE_MIN) { + printf("%s: Tx BD ring length must not be smaller than 2.\n", + __func__); + return -EINVAL; + } + + /* Check if MRBLR is illegal */ + if (MAX_RXBUF_LEN == 0 || (MAX_RXBUF_LEN % UEC_MRBLR_ALIGNMENT)) { + printf("%s: max rx buffer length must be mutliple of 128.\n", + __func__); + return -EINVAL; + } + + /* Both Rx and Tx are stopped */ + uec->grace_stopped_rx = 1; + uec->grace_stopped_tx = 1; + + /* Init UCC fast */ + if (ucc_fast_init(uf_info, &uccf)) { + printf("%s: failed to init ucc fast\n", __func__); + return -ENOMEM; + } + + /* Save uccf */ + uec->uccf = uccf; + + /* Convert the Tx threads number */ + if (uec_convert_threads_num(uec_info->num_threads_tx, + &num_threads_tx)) + return -EINVAL; + + /* Convert the Rx threads number */ + if (uec_convert_threads_num(uec_info->num_threads_rx, + &num_threads_rx)) + return -EINVAL; + + uf_regs = uccf->uf_regs; + + /* UEC register is following UCC fast registers */ + uec_regs = (uec_t *)(&uf_regs->ucc_eth); + + /* Save the UEC register pointer to UEC private struct */ + uec->uec_regs = uec_regs; + + /* Init UPSMR, enable hardware statistics (UCC) */ + out_be32(&uec->uccf->uf_regs->upsmr, UPSMR_INIT_VALUE); + + /* Init MACCFG1, flow control disable, disable Tx and Rx */ + out_be32(&uec_regs->maccfg1, MACCFG1_INIT_VALUE); + + /* Init MACCFG2, length check, MAC PAD and CRC enable */ + out_be32(&uec_regs->maccfg2, MACCFG2_INIT_VALUE); + + /* Setup UTBIPAR */ + utbipar = in_be32(&uec_regs->utbipar); + utbipar &= ~UTBIPAR_PHY_ADDRESS_MASK; + + /* Initialize UTBIPAR address to CONFIG_UTBIPAR_INIT_TBIPA for ALL UEC. + * This frees up the remaining SMI addresses for use. + */ + utbipar |= CONFIG_UTBIPAR_INIT_TBIPA << UTBIPAR_PHY_ADDRESS_SHIFT; + out_be32(&uec_regs->utbipar, utbipar); + + /* Allocate Tx BDs */ + length = ((uec_info->tx_bd_ring_len * SIZEOFBD) / + UEC_TX_BD_RING_SIZE_MEMORY_ALIGNMENT) * + UEC_TX_BD_RING_SIZE_MEMORY_ALIGNMENT; + if ((uec_info->tx_bd_ring_len * SIZEOFBD) % + UEC_TX_BD_RING_SIZE_MEMORY_ALIGNMENT) + length += UEC_TX_BD_RING_SIZE_MEMORY_ALIGNMENT; + + align = UEC_TX_BD_RING_ALIGNMENT; + uec->tx_bd_ring_offset = (u32)malloc((u32)(length + align)); + if (uec->tx_bd_ring_offset != 0) + uec->p_tx_bd_ring = (u8 *)((uec->tx_bd_ring_offset + align) + & ~(align - 1)); + + /* Zero all of Tx BDs */ + memset((void *)(uec->tx_bd_ring_offset), 0, length + align); + + /* Allocate Rx BDs */ + length = uec_info->rx_bd_ring_len * SIZEOFBD; + align = UEC_RX_BD_RING_ALIGNMENT; + uec->rx_bd_ring_offset = (u32)(malloc((u32)(length + align))); + if (uec->rx_bd_ring_offset != 0) + uec->p_rx_bd_ring = (u8 *)((uec->rx_bd_ring_offset + align) + & ~(align - 1)); + + /* Zero all of Rx BDs */ + memset((void *)(uec->rx_bd_ring_offset), 0, length + align); + + /* Allocate Rx buffer */ + length = uec_info->rx_bd_ring_len * MAX_RXBUF_LEN; + align = UEC_RX_DATA_BUF_ALIGNMENT; + uec->rx_buf_offset = (u32)malloc(length + align); + if (uec->rx_buf_offset != 0) + uec->p_rx_buf = (u8 *)((uec->rx_buf_offset + align) + & ~(align - 1)); + + /* Zero all of the Rx buffer */ + memset((void *)(uec->rx_buf_offset), 0, length + align); + + /* Init TxBD ring */ + bd = (struct buffer_descriptor *)uec->p_tx_bd_ring; + uec->tx_bd = bd; + + for (i = 0; i < uec_info->tx_bd_ring_len; i++) { + BD_DATA_CLEAR(bd); + BD_STATUS_SET(bd, 0); + BD_LENGTH_SET(bd, 0); + bd++; + } + BD_STATUS_SET((--bd), TX_BD_WRAP); + + /* Init RxBD ring */ + bd = (struct buffer_descriptor *)uec->p_rx_bd_ring; + uec->rx_bd = bd; + buf = uec->p_rx_buf; + for (i = 0; i < uec_info->rx_bd_ring_len; i++) { + BD_DATA_SET(bd, buf); + BD_LENGTH_SET(bd, 0); + BD_STATUS_SET(bd, RX_BD_EMPTY); + buf += MAX_RXBUF_LEN; + bd++; + } + BD_STATUS_SET((--bd), RX_BD_WRAP | RX_BD_EMPTY); + + /* Init global Tx parameter RAM */ + uec_init_tx_parameter(uec, num_threads_tx); + + /* Init global Rx parameter RAM */ + uec_init_rx_parameter(uec, num_threads_rx); + + /* Init ethernet Tx and Rx parameter command */ + if (uec_issue_init_enet_rxtx_cmd(uec, num_threads_tx, + num_threads_rx)) { + printf("%s issue init enet cmd failed\n", __func__); + return -ENOMEM; + } + return 0; +} + +/* Convert a string to a QE clock source enum + * + * This function takes a string, typically from a property in the device + * tree, and returns the corresponding "enum qe_clock" value. + */ +enum qe_clock qe_clock_source(const char *source) +{ + unsigned int i; + + if (strcasecmp(source, "none") == 0) + return QE_CLK_NONE; + + if (strncasecmp(source, "brg", 3) == 0) { + i = simple_strtoul(source + 3, NULL, 10); + if (i >= 1 && i <= 16) + return (QE_BRG1 - 1) + i; + else + return QE_CLK_DUMMY; + } + + if (strncasecmp(source, "clk", 3) == 0) { + i = simple_strtoul(source + 3, NULL, 10); + if (i >= 1 && i <= 24) + return (QE_CLK1 - 1) + i; + else + return QE_CLK_DUMMY; + } + + return QE_CLK_DUMMY; +} + +static void qe_uec_set_eth_type(struct udevice *dev) +{ + struct qe_uec_priv *priv = dev_get_priv(dev); + struct uec_priv *uec = priv->uec; + struct uec_inf *uec_info = uec->uec_info; + struct ucc_fast_inf *uf_info = &uec_info->uf_info; + + switch (uec_info->enet_interface_type) { + case PHY_INTERFACE_MODE_GMII: + case PHY_INTERFACE_MODE_RGMII: + case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII_RXID: + case PHY_INTERFACE_MODE_RGMII_TXID: + case PHY_INTERFACE_MODE_TBI: + case PHY_INTERFACE_MODE_RTBI: + case PHY_INTERFACE_MODE_SGMII: + uf_info->eth_type = GIGA_ETH; + break; + default: + uf_info->eth_type = FAST_ETH; + break; + } +} + +static int qe_uec_set_uec_info(struct udevice *dev) +{ + struct qe_uec_priv *priv = dev_get_priv(dev); + struct eth_pdata *pdata = dev_get_platdata(dev); + struct uec_priv *uec = priv->uec; + struct uec_inf *uec_info; + struct ucc_fast_inf *uf_info; + const char *s; + int ret; + u32 val; + + uec_info = (struct uec_inf *)malloc(sizeof(struct uec_inf)); + if (!uec_info) + return -ENOMEM; + + uf_info = &uec_info->uf_info; + + ret = dev_read_u32(dev, "cell-index", &val); + if (ret) { + ret = dev_read_u32(dev, "device-id", &val); + if (ret) { + pr_err("no cell-index nor device-id found!"); + goto out; + } + } + + uf_info->ucc_num = val - 1; + if (uf_info->ucc_num < 0 || uf_info->ucc_num > 7) { + ret = -ENODEV; + goto out; + } + + ret = dev_read_string_index(dev, "rx-clock-name", 0, &s); + if (!ret) { + uf_info->rx_clock = qe_clock_source(s); + if (uf_info->rx_clock < QE_CLK_NONE || + uf_info->rx_clock > QE_CLK24) { + pr_err("invalid rx-clock-name property\n"); + ret = -EINVAL; + goto out; + } + } else { + ret = dev_read_u32(dev, "rx-clock", &val); + if (ret) { + /* + * If both rx-clock-name and rx-clock are missing, + * we want to tell people to use rx-clock-name. + */ + pr_err("missing rx-clock-name property\n"); + goto out; + } + if (val < QE_CLK_NONE || val > QE_CLK24) { + pr_err("invalid rx-clock property\n"); + ret = -EINVAL; + goto out; + } + uf_info->rx_clock = val; + } + + ret = dev_read_string_index(dev, "tx-clock-name", 0, &s); + if (!ret) { + uf_info->tx_clock = qe_clock_source(s); + if (uf_info->tx_clock < QE_CLK_NONE || + uf_info->tx_clock > QE_CLK24) { + pr_err("invalid tx-clock-name property\n"); + ret = -EINVAL; + goto out; + } + } else { + ret = dev_read_u32(dev, "tx-clock", &val); + if (ret) { + pr_err("missing tx-clock-name property\n"); + goto out; + } + if (val < QE_CLK_NONE || val > QE_CLK24) { + pr_err("invalid tx-clock property\n"); + ret = -EINVAL; + goto out; + } + uf_info->tx_clock = val; + } + + uec_info->num_threads_tx = UEC_NUM_OF_THREADS_1; + uec_info->num_threads_rx = UEC_NUM_OF_THREADS_1; + uec_info->risc_tx = QE_RISC_ALLOCATION_RISC1_AND_RISC2; + uec_info->risc_rx = QE_RISC_ALLOCATION_RISC1_AND_RISC2; + uec_info->tx_bd_ring_len = 16; + uec_info->rx_bd_ring_len = 16; +#if (MAX_QE_RISC == 4) + uec_info->risc_tx = QE_RISC_ALLOCATION_FOUR_RISCS; + uec_info->risc_rx = QE_RISC_ALLOCATION_FOUR_RISCS; +#endif + + uec_info->enet_interface_type = pdata->phy_interface; + + uec->uec_info = uec_info; + qe_uec_set_eth_type(dev); + + return 0; +out: + free(uec_info); + return ret; +} + +static int qe_uec_probe(struct udevice *dev) +{ + struct qe_uec_priv *priv = dev_get_priv(dev); + struct eth_pdata *pdata = dev_get_platdata(dev); + struct uec_priv *uec; + int ret; + + /* Allocate the UEC private struct */ + uec = (struct uec_priv *)malloc(sizeof(struct uec_priv)); + if (!uec) + return -ENOMEM; + + memset(uec, 0, sizeof(struct uec_priv)); + priv->uec = uec; + uec->uec_regs = (uec_t *)pdata->iobase; + + /* setup uec info struct */ + ret = qe_uec_set_uec_info(dev); + if (ret) { + free(uec); + return ret; + } + + ret = uec_startup(dev); + if (ret) { + free(uec->uec_info); + free(uec); + return ret; + } + + priv->phydev = dm_eth_phy_connect(dev); + return 0; +} + +/* + * Remove the driver from an interface: + * - free up allocated memory + */ +static int qe_uec_remove(struct udevice *dev) +{ + struct qe_uec_priv *priv = dev_get_priv(dev); + + free(priv->uec); + return 0; +} + +static int qe_uec_ofdata_to_platdata(struct udevice *dev) +{ + struct eth_pdata *pdata = dev_get_platdata(dev); + const char *phy_mode; + + pdata->iobase = (phys_addr_t)devfdt_get_addr(dev); + + pdata->phy_interface = -1; + phy_mode = fdt_getprop(gd->fdt_blob, dev_of_offset(dev), + "phy-connection-type", NULL); + if (phy_mode) + pdata->phy_interface = phy_get_interface_by_name(phy_mode); + if (pdata->phy_interface == -1) { + debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode); + return -EINVAL; + } + + return 0; +} + +static const struct udevice_id qe_uec_ids[] = { + { .compatible = QE_UEC_DRIVER_NAME }, + { } +}; + +U_BOOT_DRIVER(eth_qe_uec) = { + .name = QE_UEC_DRIVER_NAME, + .id = UCLASS_ETH, + .of_match = qe_uec_ids, + .ofdata_to_platdata = qe_uec_ofdata_to_platdata, + .probe = qe_uec_probe, + .remove = qe_uec_remove, + .ops = &qe_uec_eth_ops, + .priv_auto_alloc_size = sizeof(struct qe_uec_priv), + .platdata_auto_alloc_size = sizeof(struct eth_pdata), +}; diff --git a/drivers/net/qe/dm_qe_uec.h b/drivers/net/qe/dm_qe_uec.h new file mode 100644 index 0000000000..690093caa2 --- /dev/null +++ b/drivers/net/qe/dm_qe_uec.h @@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0+ + * + * QE UEC ethernet controller driver + * + * based on drivers/qe/uec.c from NXP + * + * Copyright (C) 2020 Heiko Schocher + */ + +#ifndef _DM_QE_UEC_H +#define _DM_QE_UEC_H + +#define qe_uec_dbg(dev, fmt, args...) debug("%s:" fmt, dev->name, ##args) + +#include "uec.h" + +/* QE UEC private structure */ +struct qe_uec_priv { + struct uec_priv *uec; + struct phy_device *phydev; +}; +#endif diff --git a/drivers/net/qe/dm_qe_uec_phy.c b/drivers/net/qe/dm_qe_uec_phy.c new file mode 100644 index 0000000000..02ce08edad --- /dev/null +++ b/drivers/net/qe/dm_qe_uec_phy.c @@ -0,0 +1,163 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * QE UEC ethernet phy controller driver + * + * based on phy parts of drivers/qe/uec.c and drivers/qe/uec_phy.c + * from NXP + * + * Copyright (C) 2020 Heiko Schocher + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "dm_qe_uec.h" + +struct qe_uec_mdio_priv { + struct ucc_mii_mng *base; +}; + +static int +qe_uec_mdio_read(struct udevice *dev, int addr, int devad, int reg) +{ + struct qe_uec_mdio_priv *priv = dev_get_priv(dev); + struct ucc_mii_mng *regs = priv->base; + u32 tmp_reg; + u16 value; + + debug("%s: regs: %p addr: %x devad: %x reg: %x\n", __func__, regs, + addr, devad, reg); + /* Setting up the MII management Address Register */ + tmp_reg = ((u32)addr << MIIMADD_PHY_ADDRESS_SHIFT) | reg; + out_be32(®s->miimadd, tmp_reg); + + /* clear MII management command cycle */ + out_be32(®s->miimcom, 0); + sync(); + + /* Perform an MII management read cycle */ + out_be32(®s->miimcom, MIIMCOM_READ_CYCLE); + + /* Wait till MII management write is complete */ + while ((in_be32(®s->miimind)) & + (MIIMIND_NOT_VALID | MIIMIND_BUSY)) + ; + + /* Read MII management status */ + value = (u16)in_be32(®s->miimstat); + if (value == 0xffff) + return -EINVAL; + + return value; +}; + +static int +qe_uec_mdio_write(struct udevice *dev, int addr, int devad, int reg, + u16 value) +{ + struct qe_uec_mdio_priv *priv = dev_get_priv(dev); + struct ucc_mii_mng *regs = priv->base; + u32 tmp_reg; + + debug("%s: regs: %p addr: %x devad: %x reg: %x val: %x\n", __func__, + regs, addr, devad, reg, value); + + /* Stop the MII management read cycle */ + out_be32(®s->miimcom, 0); + /* Setting up the MII management Address Register */ + tmp_reg = ((u32)addr << MIIMADD_PHY_ADDRESS_SHIFT) | reg; + out_be32(®s->miimadd, tmp_reg); + + /* Setting up the MII management Control Register with the value */ + out_be32(®s->miimcon, (u32)value); + sync(); + + /* Wait till MII management write is complete */ + while ((in_be32(®s->miimind)) & MIIMIND_BUSY) + ; + + return 0; +}; + +static const struct mdio_ops qe_uec_mdio_ops = { + .read = qe_uec_mdio_read, + .write = qe_uec_mdio_write, +}; + +static int qe_uec_mdio_probe(struct udevice *dev) +{ + struct qe_uec_mdio_priv *priv = dev_get_priv(dev); + fdt_size_t base; + ofnode node; + u32 num = 0; + int ret = -ENODEV; + + priv->base = (struct ucc_mii_mng *)dev_read_addr(dev); + base = (fdt_size_t)priv->base; + + /* + * idea from linux: + * drivers/net/ethernet/freescale/fsl_pq_mdio.c + * + * Find the UCC node that controls the given MDIO node + * + * For some reason, the QE MDIO nodes are not children of the UCC + * devices that control them. Therefore, we need to scan all UCC + * nodes looking for the one that encompases the given MDIO node. + * We do this by comparing physical addresses. The 'start' and + * 'end' addresses of the MDIO node are passed, and the correct + * UCC node will cover the entire address range. + */ + node = ofnode_by_compatible(ofnode_null(), "ucc_geth"); + while (ofnode_valid(node)) { + fdt_size_t size; + fdt_addr_t addr; + + addr = ofnode_get_addr_index(node, 0); + ret = ofnode_get_addr_size_index(node, 0, &size); + + if (addr == FDT_ADDR_T_NONE) { + node = ofnode_by_compatible(node, "ucc_geth"); + continue; + } + + /* check if priv->base in start end */ + if (base > addr && base < (addr + size)) { + ret = ofnode_read_u32(node, "cell-index", &num); + if (ret) + ret = ofnode_read_u32(node, "device-id", + &num); + break; + } + node = ofnode_by_compatible(node, "ucc_geth"); + } + + if (ret) { + printf("%s: no cell-index nor device-id found!", __func__); + return ret; + } + + /* Setup MII master clock source */ + qe_set_mii_clk_src(num - 1); + + return 0; +} + +static const struct udevice_id qe_uec_mdio_ids[] = { + { .compatible = "fsl,ucc-mdio" }, + { } +}; + +U_BOOT_DRIVER(mvmdio) = { + .name = "qe_uec_mdio", + .id = UCLASS_MDIO, + .of_match = qe_uec_mdio_ids, + .probe = qe_uec_mdio_probe, + .ops = &qe_uec_mdio_ops, + .priv_auto_alloc_size = sizeof(struct qe_uec_mdio_priv), +}; diff --git a/drivers/net/qe/uccf.c b/drivers/net/qe/uccf.c new file mode 100644 index 0000000000..306f1ea1db --- /dev/null +++ b/drivers/net/qe/uccf.c @@ -0,0 +1,507 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2006 Freescale Semiconductor, Inc. + * + * Dave Liu + * based on source code of Shlomi Gridish + */ + +#include +#include +#include +#include +#include +#include "uccf.h" +#include + +void ucc_fast_transmit_on_demand(struct ucc_fast_priv *uccf) +{ + out_be16(&uccf->uf_regs->utodr, UCC_FAST_TOD); +} + +u32 ucc_fast_get_qe_cr_subblock(int ucc_num) +{ + switch (ucc_num) { + case 0: + return QE_CR_SUBBLOCK_UCCFAST1; + case 1: + return QE_CR_SUBBLOCK_UCCFAST2; + case 2: + return QE_CR_SUBBLOCK_UCCFAST3; + case 3: + return QE_CR_SUBBLOCK_UCCFAST4; + case 4: + return QE_CR_SUBBLOCK_UCCFAST5; + case 5: + return QE_CR_SUBBLOCK_UCCFAST6; + case 6: + return QE_CR_SUBBLOCK_UCCFAST7; + case 7: + return QE_CR_SUBBLOCK_UCCFAST8; + default: + return QE_CR_SUBBLOCK_INVALID; + } +} + +static void ucc_get_cmxucr_reg(int ucc_num, u32 **p_cmxucr, + u8 *reg_num, u8 *shift) +{ + switch (ucc_num) { + case 0: /* UCC1 */ + *p_cmxucr = &qe_immr->qmx.cmxucr1; + *reg_num = 1; + *shift = 16; + break; + case 2: /* UCC3 */ + *p_cmxucr = &qe_immr->qmx.cmxucr1; + *reg_num = 1; + *shift = 0; + break; + case 4: /* UCC5 */ + *p_cmxucr = &qe_immr->qmx.cmxucr2; + *reg_num = 2; + *shift = 16; + break; + case 6: /* UCC7 */ + *p_cmxucr = &qe_immr->qmx.cmxucr2; + *reg_num = 2; + *shift = 0; + break; + case 1: /* UCC2 */ + *p_cmxucr = &qe_immr->qmx.cmxucr3; + *reg_num = 3; + *shift = 16; + break; + case 3: /* UCC4 */ + *p_cmxucr = &qe_immr->qmx.cmxucr3; + *reg_num = 3; + *shift = 0; + break; + case 5: /* UCC6 */ + *p_cmxucr = &qe_immr->qmx.cmxucr4; + *reg_num = 4; + *shift = 16; + break; + case 7: /* UCC8 */ + *p_cmxucr = &qe_immr->qmx.cmxucr4; + *reg_num = 4; + *shift = 0; + break; + default: + break; + } +} + +static int ucc_set_clk_src(int ucc_num, qe_clock_e clock, comm_dir_e mode) +{ + u32 *p_cmxucr = NULL; + u8 reg_num = 0; + u8 shift = 0; + u32 clk_bits; + u32 clk_mask; + int source = -1; + + /* check if the UCC number is in range. */ + if ((ucc_num > UCC_MAX_NUM - 1) || ucc_num < 0) + return -EINVAL; + + if (!(mode == COMM_DIR_RX || mode == COMM_DIR_TX)) { + printf("%s: bad comm mode type passed\n", __func__); + return -EINVAL; + } + + ucc_get_cmxucr_reg(ucc_num, &p_cmxucr, ®_num, &shift); + + switch (reg_num) { + case 1: + switch (clock) { + case QE_BRG1: + source = 1; + break; + case QE_BRG2: + source = 2; + break; + case QE_BRG7: + source = 3; + break; + case QE_BRG8: + source = 4; + break; + case QE_CLK9: + source = 5; + break; + case QE_CLK10: + source = 6; + break; + case QE_CLK11: + source = 7; + break; + case QE_CLK12: + source = 8; + break; + case QE_CLK15: + source = 9; + break; + case QE_CLK16: + source = 10; + break; + default: + source = -1; + break; + } + break; + case 2: + switch (clock) { + case QE_BRG5: + source = 1; + break; + case QE_BRG6: + source = 2; + break; + case QE_BRG7: + source = 3; + break; + case QE_BRG8: + source = 4; + break; + case QE_CLK13: + source = 5; + break; + case QE_CLK14: + source = 6; + break; + case QE_CLK19: + source = 7; + break; + case QE_CLK20: + source = 8; + break; + case QE_CLK15: + source = 9; + break; + case QE_CLK16: + source = 10; + break; + default: + source = -1; + break; + } + break; + case 3: + switch (clock) { + case QE_BRG9: + source = 1; + break; + case QE_BRG10: + source = 2; + break; + case QE_BRG15: + source = 3; + break; + case QE_BRG16: + source = 4; + break; + case QE_CLK3: + source = 5; + break; + case QE_CLK4: + source = 6; + break; + case QE_CLK17: + source = 7; + break; + case QE_CLK18: + source = 8; + break; + case QE_CLK7: + source = 9; + break; + case QE_CLK8: + source = 10; + break; + case QE_CLK16: + source = 11; + break; + default: + source = -1; + break; + } + break; + case 4: + switch (clock) { + case QE_BRG13: + source = 1; + break; + case QE_BRG14: + source = 2; + break; + case QE_BRG15: + source = 3; + break; + case QE_BRG16: + source = 4; + break; + case QE_CLK5: + source = 5; + break; + case QE_CLK6: + source = 6; + break; + case QE_CLK21: + source = 7; + break; + case QE_CLK22: + source = 8; + break; + case QE_CLK7: + source = 9; + break; + case QE_CLK8: + source = 10; + break; + case QE_CLK16: + source = 11; + break; + default: + source = -1; + break; + } + break; + default: + source = -1; + break; + } + + if (source == -1) { + printf("%s: Bad combination of clock and UCC\n", __func__); + return -ENOENT; + } + + clk_bits = (u32)source; + clk_mask = QE_CMXUCR_TX_CLK_SRC_MASK; + if (mode == COMM_DIR_RX) { + clk_bits <<= 4; /* Rx field is 4 bits to left of Tx field */ + clk_mask <<= 4; /* Rx field is 4 bits to left of Tx field */ + } + clk_bits <<= shift; + clk_mask <<= shift; + + out_be32(p_cmxucr, (in_be32(p_cmxucr) & ~clk_mask) | clk_bits); + + return 0; +} + +static uint ucc_get_reg_baseaddr(int ucc_num) +{ + uint base = 0; + + /* check if the UCC number is in range */ + if ((ucc_num > UCC_MAX_NUM - 1) || ucc_num < 0) { + printf("%s: the UCC num not in ranges\n", __func__); + return 0; + } + + switch (ucc_num) { + case 0: + base = 0x00002000; + break; + case 1: + base = 0x00003000; + break; + case 2: + base = 0x00002200; + break; + case 3: + base = 0x00003200; + break; + case 4: + base = 0x00002400; + break; + case 5: + base = 0x00003400; + break; + case 6: + base = 0x00002600; + break; + case 7: + base = 0x00003600; + break; + default: + break; + } + + base = (uint)qe_immr + base; + return base; +} + +void ucc_fast_enable(struct ucc_fast_priv *uccf, comm_dir_e mode) +{ + ucc_fast_t *uf_regs; + u32 gumr; + + uf_regs = uccf->uf_regs; + + /* Enable reception and/or transmission on this UCC. */ + gumr = in_be32(&uf_regs->gumr); + if (mode & COMM_DIR_TX) { + gumr |= UCC_FAST_GUMR_ENT; + uccf->enabled_tx = 1; + } + if (mode & COMM_DIR_RX) { + gumr |= UCC_FAST_GUMR_ENR; + uccf->enabled_rx = 1; + } + out_be32(&uf_regs->gumr, gumr); +} + +void ucc_fast_disable(struct ucc_fast_priv *uccf, comm_dir_e mode) +{ + ucc_fast_t *uf_regs; + u32 gumr; + + uf_regs = uccf->uf_regs; + + /* Disable reception and/or transmission on this UCC. */ + gumr = in_be32(&uf_regs->gumr); + if (mode & COMM_DIR_TX) { + gumr &= ~UCC_FAST_GUMR_ENT; + uccf->enabled_tx = 0; + } + if (mode & COMM_DIR_RX) { + gumr &= ~UCC_FAST_GUMR_ENR; + uccf->enabled_rx = 0; + } + out_be32(&uf_regs->gumr, gumr); +} + +int ucc_fast_init(struct ucc_fast_inf *uf_info, + struct ucc_fast_priv **uccf_ret) +{ + struct ucc_fast_priv *uccf; + ucc_fast_t *uf_regs; + + if (!uf_info) + return -EINVAL; + + if (uf_info->ucc_num < 0 || (uf_info->ucc_num > UCC_MAX_NUM - 1)) { + printf("%s: Illagal UCC number!\n", __func__); + return -EINVAL; + } + + uccf = (struct ucc_fast_priv *)malloc(sizeof(struct ucc_fast_priv)); + if (!uccf) { + printf("%s: No memory for UCC fast data structure!\n", + __func__); + return -ENOMEM; + } + memset(uccf, 0, sizeof(struct ucc_fast_priv)); + + /* Save fast UCC structure */ + uccf->uf_info = uf_info; + uccf->uf_regs = (ucc_fast_t *)ucc_get_reg_baseaddr(uf_info->ucc_num); + + if (!uccf->uf_regs) { + printf("%s: No memory map for UCC fast controller!\n", + __func__); + return -ENOMEM; + } + + uccf->enabled_tx = 0; + uccf->enabled_rx = 0; + + uf_regs = uccf->uf_regs; + uccf->p_ucce = (u32 *)&uf_regs->ucce; + uccf->p_uccm = (u32 *)&uf_regs->uccm; + + /* Init GUEMR register, UCC both Rx and Tx is Fast protocol */ + out_8(&uf_regs->guemr, UCC_GUEMR_SET_RESERVED3 | UCC_GUEMR_MODE_FAST_RX + | UCC_GUEMR_MODE_FAST_TX); + + /* Set GUMR, disable UCC both Rx and Tx, Ethernet protocol */ + out_be32(&uf_regs->gumr, UCC_FAST_GUMR_ETH); + + /* Set the Giga ethernet VFIFO stuff */ + if (uf_info->eth_type == GIGA_ETH) { + /* Allocate memory for Tx Virtual Fifo */ + uccf->ucc_fast_tx_virtual_fifo_base_offset = + qe_muram_alloc(UCC_GETH_UTFS_GIGA_INIT, + UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT); + + /* Allocate memory for Rx Virtual Fifo */ + uccf->ucc_fast_rx_virtual_fifo_base_offset = + qe_muram_alloc(UCC_GETH_URFS_GIGA_INIT + + UCC_FAST_RX_VIRTUAL_FIFO_SIZE_PAD, + UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT); + + /* utfb, urfb are offsets from MURAM base */ + out_be32(&uf_regs->utfb, + uccf->ucc_fast_tx_virtual_fifo_base_offset); + out_be32(&uf_regs->urfb, + uccf->ucc_fast_rx_virtual_fifo_base_offset); + + /* Set Virtual Fifo registers */ + out_be16(&uf_regs->urfs, UCC_GETH_URFS_GIGA_INIT); + out_be16(&uf_regs->urfet, UCC_GETH_URFET_GIGA_INIT); + out_be16(&uf_regs->urfset, UCC_GETH_URFSET_GIGA_INIT); + out_be16(&uf_regs->utfs, UCC_GETH_UTFS_GIGA_INIT); + out_be16(&uf_regs->utfet, UCC_GETH_UTFET_GIGA_INIT); + out_be16(&uf_regs->utftt, UCC_GETH_UTFTT_GIGA_INIT); + } + + /* Set the Fast ethernet VFIFO stuff */ + if (uf_info->eth_type == FAST_ETH) { + /* Allocate memory for Tx Virtual Fifo */ + uccf->ucc_fast_tx_virtual_fifo_base_offset = + qe_muram_alloc(UCC_GETH_UTFS_INIT, + UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT); + + /* Allocate memory for Rx Virtual Fifo */ + uccf->ucc_fast_rx_virtual_fifo_base_offset = + qe_muram_alloc(UCC_GETH_URFS_INIT + + UCC_FAST_RX_VIRTUAL_FIFO_SIZE_PAD, + UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT); + + /* utfb, urfb are offsets from MURAM base */ + out_be32(&uf_regs->utfb, + uccf->ucc_fast_tx_virtual_fifo_base_offset); + out_be32(&uf_regs->urfb, + uccf->ucc_fast_rx_virtual_fifo_base_offset); + + /* Set Virtual Fifo registers */ + out_be16(&uf_regs->urfs, UCC_GETH_URFS_INIT); + out_be16(&uf_regs->urfet, UCC_GETH_URFET_INIT); + out_be16(&uf_regs->urfset, UCC_GETH_URFSET_INIT); + out_be16(&uf_regs->utfs, UCC_GETH_UTFS_INIT); + out_be16(&uf_regs->utfet, UCC_GETH_UTFET_INIT); + out_be16(&uf_regs->utftt, UCC_GETH_UTFTT_INIT); + } + + /* Rx clock routing */ + if (uf_info->rx_clock != QE_CLK_NONE) { + if (ucc_set_clk_src(uf_info->ucc_num, + uf_info->rx_clock, COMM_DIR_RX)) { + printf("%s: Illegal value for parameter 'RxClock'.\n", + __func__); + return -EINVAL; + } + } + + /* Tx clock routing */ + if (uf_info->tx_clock != QE_CLK_NONE) { + if (ucc_set_clk_src(uf_info->ucc_num, + uf_info->tx_clock, COMM_DIR_TX)) { + printf("%s: Illegal value for parameter 'TxClock'.\n", + __func__); + return -EINVAL; + } + } + + /* Clear interrupt mask register to disable all of interrupts */ + out_be32(&uf_regs->uccm, 0x0); + + /* Writing '1' to clear all of envents */ + out_be32(&uf_regs->ucce, 0xffffffff); + + *uccf_ret = uccf; + return 0; +} diff --git a/drivers/net/qe/uccf.h b/drivers/net/qe/uccf.h new file mode 100644 index 0000000000..99f8458edf --- /dev/null +++ b/drivers/net/qe/uccf.h @@ -0,0 +1,119 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2006 Freescale Semiconductor, Inc. + * + * Dave Liu + * based on source code of Shlomi Gridish + */ + +#ifndef __UCCF_H__ +#define __UCCF_H__ + +#include "common.h" +#include "linux/immap_qe.h" +#include + +/* Fast or Giga ethernet */ +enum enet_type { + FAST_ETH, + GIGA_ETH, +}; + +/* General UCC Extended Mode Register */ +#define UCC_GUEMR_MODE_MASK_RX 0x02 +#define UCC_GUEMR_MODE_MASK_TX 0x01 +#define UCC_GUEMR_MODE_FAST_RX 0x02 +#define UCC_GUEMR_MODE_FAST_TX 0x01 +#define UCC_GUEMR_MODE_SLOW_RX 0x00 +#define UCC_GUEMR_MODE_SLOW_TX 0x00 +/* Bit 3 must be set 1 */ +#define UCC_GUEMR_SET_RESERVED3 0x10 + +/* General UCC FAST Mode Register */ +#define UCC_FAST_GUMR_TCI 0x20000000 +#define UCC_FAST_GUMR_TRX 0x10000000 +#define UCC_FAST_GUMR_TTX 0x08000000 +#define UCC_FAST_GUMR_CDP 0x04000000 +#define UCC_FAST_GUMR_CTSP 0x02000000 +#define UCC_FAST_GUMR_CDS 0x01000000 +#define UCC_FAST_GUMR_CTSS 0x00800000 +#define UCC_FAST_GUMR_TXSY 0x00020000 +#define UCC_FAST_GUMR_RSYN 0x00010000 +#define UCC_FAST_GUMR_RTSM 0x00002000 +#define UCC_FAST_GUMR_REVD 0x00000400 +#define UCC_FAST_GUMR_ENR 0x00000020 +#define UCC_FAST_GUMR_ENT 0x00000010 + +/* GUMR [MODE] bit maps */ +#define UCC_FAST_GUMR_HDLC 0x00000000 +#define UCC_FAST_GUMR_QMC 0x00000002 +#define UCC_FAST_GUMR_UART 0x00000004 +#define UCC_FAST_GUMR_BISYNC 0x00000008 +#define UCC_FAST_GUMR_ATM 0x0000000a +#define UCC_FAST_GUMR_ETH 0x0000000c + +/* Transmit On Demand (UTORD) */ +#define UCC_SLOW_TOD 0x8000 +#define UCC_FAST_TOD 0x8000 + +/* Fast Ethernet (10/100 Mbps) */ +/* Rx virtual FIFO size */ +#define UCC_GETH_URFS_INIT 512 +/* 1/2 urfs */ +#define UCC_GETH_URFET_INIT 256 +/* 3/4 urfs */ +#define UCC_GETH_URFSET_INIT 384 +/* Tx virtual FIFO size */ +#define UCC_GETH_UTFS_INIT 512 +/* 1/2 utfs */ +#define UCC_GETH_UTFET_INIT 256 +#define UCC_GETH_UTFTT_INIT 128 + +/* Gigabit Ethernet (1000 Mbps) */ +/* Rx virtual FIFO size */ +#define UCC_GETH_URFS_GIGA_INIT 4096/*2048*/ +/* 1/2 urfs */ +#define UCC_GETH_URFET_GIGA_INIT 2048/*1024*/ +/* 3/4 urfs */ +#define UCC_GETH_URFSET_GIGA_INIT 3072/*1536*/ +/* Tx virtual FIFO size */ +#define UCC_GETH_UTFS_GIGA_INIT 8192/*2048*/ +/* 1/2 utfs */ +#define UCC_GETH_UTFET_GIGA_INIT 4096/*1024*/ +#define UCC_GETH_UTFTT_GIGA_INIT 0x400/*0x40*/ + +/* UCC fast alignment */ +#define UCC_FAST_RX_ALIGN 4 +#define UCC_FAST_MRBLR_ALIGNMENT 4 +#define UCC_FAST_VIRT_FIFO_REGS_ALIGNMENT 8 + +/* Sizes */ +#define UCC_FAST_RX_VIRTUAL_FIFO_SIZE_PAD 8 + +/* UCC fast structure. */ +struct ucc_fast_inf { + int ucc_num; + qe_clock_e rx_clock; + qe_clock_e tx_clock; + enum enet_type eth_type; +}; + +struct ucc_fast_priv { + struct ucc_fast_inf *uf_info; + ucc_fast_t *uf_regs; /* a pointer to memory map of UCC regs */ + u32 *p_ucce; /* a pointer to the event register */ + u32 *p_uccm; /* a pointer to the mask register */ + int enabled_tx; /* whether UCC is enabled for Tx (ENT) */ + int enabled_rx; /* whether UCC is enabled for Rx (ENR) */ + u32 ucc_fast_tx_virtual_fifo_base_offset; + u32 ucc_fast_rx_virtual_fifo_base_offset; +}; + +void ucc_fast_transmit_on_demand(struct ucc_fast_priv *uccf); +u32 ucc_fast_get_qe_cr_subblock(int ucc_num); +void ucc_fast_enable(struct ucc_fast_priv *uccf, comm_dir_e mode); +void ucc_fast_disable(struct ucc_fast_priv *uccf, comm_dir_e mode); +int ucc_fast_init(struct ucc_fast_inf *uf_info, + struct ucc_fast_priv **uccf_ret); + +#endif /* __UCCF_H__ */ diff --git a/drivers/net/qe/uec.h b/drivers/net/qe/uec.h new file mode 100644 index 0000000000..7cd4b8737a --- /dev/null +++ b/drivers/net/qe/uec.h @@ -0,0 +1,693 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2006-2010 Freescale Semiconductor, Inc. + * + * Dave Liu + * based on source code of Shlomi Gridish + */ + +#ifndef __UEC_H__ +#define __UEC_H__ + +#include "uccf.h" +#include +#include + +#define MAX_TX_THREADS 8 +#define MAX_RX_THREADS 8 +#define MAX_TX_QUEUES 8 +#define MAX_RX_QUEUES 8 +#define MAX_PREFETCHED_BDS 4 +#define MAX_IPH_OFFSET_ENTRY 8 +#define MAX_ENET_INIT_PARAM_ENTRIES_RX 9 +#define MAX_ENET_INIT_PARAM_ENTRIES_TX 8 + +/* UEC UPSMR (Protocol Specific Mode Register) + */ +#define UPSMR_ECM 0x04000000 /* Enable CAM Miss */ +#define UPSMR_HSE 0x02000000 /* Hardware Statistics Enable */ +#define UPSMR_PRO 0x00400000 /* Promiscuous */ +#define UPSMR_CAP 0x00200000 /* CAM polarity */ +#define UPSMR_RSH 0x00100000 /* Receive Short Frames */ +#define UPSMR_RPM 0x00080000 /* Reduced Pin Mode interfaces */ +#define UPSMR_R10M 0x00040000 /* RGMII/RMII 10 Mode */ +#define UPSMR_RLPB 0x00020000 /* RMII Loopback Mode */ +#define UPSMR_TBIM 0x00010000 /* Ten-bit Interface Mode */ +#define UPSMR_RMM 0x00001000 /* RMII/RGMII Mode */ +#define UPSMR_CAM 0x00000400 /* CAM Address Matching */ +#define UPSMR_BRO 0x00000200 /* Broadcast Address */ +#define UPSMR_RES1 0x00002000 /* Reserved feild - must be 1 */ +#define UPSMR_SGMM 0x00000020 /* SGMII mode */ + +#define UPSMR_INIT_VALUE (UPSMR_HSE | UPSMR_RES1) + +/* UEC MACCFG1 (MAC Configuration 1 Register) + */ +#define MACCFG1_FLOW_RX 0x00000020 /* Flow Control Rx */ +#define MACCFG1_FLOW_TX 0x00000010 /* Flow Control Tx */ +#define MACCFG1_ENABLE_SYNCHED_RX 0x00000008 /* Enable Rx Sync */ +#define MACCFG1_ENABLE_RX 0x00000004 /* Enable Rx */ +#define MACCFG1_ENABLE_SYNCHED_TX 0x00000002 /* Enable Tx Sync */ +#define MACCFG1_ENABLE_TX 0x00000001 /* Enable Tx */ + +#define MACCFG1_INIT_VALUE (0) + +/* UEC MACCFG2 (MAC Configuration 2 Register) + */ +#define MACCFG2_PREL 0x00007000 +#define MACCFG2_PREL_SHIFT (31 - 19) +#define MACCFG2_PREL_MASK 0x0000f000 +#define MACCFG2_SRP 0x00000080 +#define MACCFG2_STP 0x00000040 +#define MACCFG2_RESERVED_1 0x00000020 /* must be set */ +#define MACCFG2_LC 0x00000010 /* Length Check */ +#define MACCFG2_MPE 0x00000008 +#define MACCFG2_FDX 0x00000001 /* Full Duplex */ +#define MACCFG2_FDX_MASK 0x00000001 +#define MACCFG2_PAD_CRC 0x00000004 +#define MACCFG2_CRC_EN 0x00000002 +#define MACCFG2_PAD_AND_CRC_MODE_NONE 0x00000000 +#define MACCFG2_PAD_AND_CRC_MODE_CRC_ONLY 0x00000002 +#define MACCFG2_PAD_AND_CRC_MODE_PAD_AND_CRC 0x00000004 +#define MACCFG2_INTERFACE_MODE_NIBBLE 0x00000100 +#define MACCFG2_INTERFACE_MODE_BYTE 0x00000200 +#define MACCFG2_INTERFACE_MODE_MASK 0x00000300 + +#define MACCFG2_INIT_VALUE (MACCFG2_PREL | MACCFG2_RESERVED_1 | \ + MACCFG2_LC | MACCFG2_PAD_CRC | MACCFG2_FDX) + +/* UEC Event Register */ +#define UCCE_MPD 0x80000000 +#define UCCE_SCAR 0x40000000 +#define UCCE_GRA 0x20000000 +#define UCCE_CBPR 0x10000000 +#define UCCE_BSY 0x08000000 +#define UCCE_RXC 0x04000000 +#define UCCE_TXC 0x02000000 +#define UCCE_TXE 0x01000000 +#define UCCE_TXB7 0x00800000 +#define UCCE_TXB6 0x00400000 +#define UCCE_TXB5 0x00200000 +#define UCCE_TXB4 0x00100000 +#define UCCE_TXB3 0x00080000 +#define UCCE_TXB2 0x00040000 +#define UCCE_TXB1 0x00020000 +#define UCCE_TXB0 0x00010000 +#define UCCE_RXB7 0x00008000 +#define UCCE_RXB6 0x00004000 +#define UCCE_RXB5 0x00002000 +#define UCCE_RXB4 0x00001000 +#define UCCE_RXB3 0x00000800 +#define UCCE_RXB2 0x00000400 +#define UCCE_RXB1 0x00000200 +#define UCCE_RXB0 0x00000100 +#define UCCE_RXF7 0x00000080 +#define UCCE_RXF6 0x00000040 +#define UCCE_RXF5 0x00000020 +#define UCCE_RXF4 0x00000010 +#define UCCE_RXF3 0x00000008 +#define UCCE_RXF2 0x00000004 +#define UCCE_RXF1 0x00000002 +#define UCCE_RXF0 0x00000001 + +#define UCCE_TXB (UCCE_TXB7 | UCCE_TXB6 | UCCE_TXB5 | UCCE_TXB4 | \ + UCCE_TXB3 | UCCE_TXB2 | UCCE_TXB1 | UCCE_TXB0) +#define UCCE_RXB (UCCE_RXB7 | UCCE_RXB6 | UCCE_RXB5 | UCCE_RXB4 | \ + UCCE_RXB3 | UCCE_RXB2 | UCCE_RXB1 | UCCE_RXB0) +#define UCCE_RXF (UCCE_RXF7 | UCCE_RXF6 | UCCE_RXF5 | UCCE_RXF4 | \ + UCCE_RXF3 | UCCE_RXF2 | UCCE_RXF1 | UCCE_RXF0) +#define UCCE_OTHER (UCCE_SCAR | UCCE_GRA | UCCE_CBPR | UCCE_BSY | \ + UCCE_RXC | UCCE_TXC | UCCE_TXE) + +/* UEC TEMODR Register */ +#define TEMODER_SCHEDULER_ENABLE 0x2000 +#define TEMODER_IP_CHECKSUM_GENERATE 0x0400 +#define TEMODER_PERFORMANCE_OPTIMIZATION_MODE1 0x0200 +#define TEMODER_RMON_STATISTICS 0x0100 +#define TEMODER_NUM_OF_QUEUES_SHIFT (15 - 15) + +#define TEMODER_INIT_VALUE 0xc000 + +/* UEC REMODR Register */ +#define REMODER_RX_RMON_STATISTICS_ENABLE 0x00001000 +#define REMODER_RX_EXTENDED_FEATURES 0x80000000 +#define REMODER_VLAN_OPERATION_TAGGED_SHIFT (31 - 9) +#define REMODER_VLAN_OPERATION_NON_TAGGED_SHIFT (31 - 10) +#define REMODER_RX_QOS_MODE_SHIFT (31 - 15) +#define REMODER_RMON_STATISTICS 0x00001000 +#define REMODER_RX_EXTENDED_FILTERING 0x00000800 +#define REMODER_NUM_OF_QUEUES_SHIFT (31 - 23) +#define REMODER_DYNAMIC_MAX_FRAME_LENGTH 0x00000008 +#define REMODER_DYNAMIC_MIN_FRAME_LENGTH 0x00000004 +#define REMODER_IP_CHECKSUM_CHECK 0x00000002 +#define REMODER_IP_ADDRESS_ALIGNMENT 0x00000001 + +#define REMODER_INIT_VALUE 0 + +/* BMRx - Bus Mode Register */ +#define BMR_GLB 0x20 +#define BMR_BO_BE 0x10 +#define BMR_DTB_SECONDARY_BUS 0x02 +#define BMR_BDB_SECONDARY_BUS 0x01 + +#define BMR_SHIFT 24 +#define BMR_INIT_VALUE (BMR_GLB | BMR_BO_BE) + +/* UEC UCCS (Ethernet Status Register) + */ +#define UCCS_BPR 0x02 +#define UCCS_PAU 0x02 +#define UCCS_MPD 0x01 + +/* UEC MIIMCFG (MII Management Configuration Register) + */ +#define MIIMCFG_RESET_MANAGEMENT 0x80000000 +#define MIIMCFG_NO_PREAMBLE 0x00000010 +#define MIIMCFG_CLOCK_DIVIDE_SHIFT (31 - 31) +#define MIIMCFG_CLOCK_DIVIDE_MASK 0x0000000f +#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_4 0x00000001 +#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_6 0x00000002 +#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_8 0x00000003 +#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_10 0x00000004 +#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_14 0x00000005 +#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_20 0x00000006 +#define MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_28 0x00000007 + +#define MIIMCFG_MNGMNT_CLC_DIV_INIT_VALUE \ + MIIMCFG_MANAGEMENT_CLOCK_DIVIDE_BY_10 + +/* UEC MIIMCOM (MII Management Command Register) + */ +#define MIIMCOM_SCAN_CYCLE 0x00000002 /* Scan cycle */ +#define MIIMCOM_READ_CYCLE 0x00000001 /* Read cycle */ + +/* UEC MIIMADD (MII Management Address Register) + */ +#define MIIMADD_PHY_ADDRESS_SHIFT (31 - 23) +#define MIIMADD_PHY_REGISTER_SHIFT (31 - 31) + +/* UEC MIIMCON (MII Management Control Register) + */ +#define MIIMCON_PHY_CONTROL_SHIFT (31 - 31) +#define MIIMCON_PHY_STATUS_SHIFT (31 - 31) + +/* UEC MIIMIND (MII Management Indicator Register) + */ +#define MIIMIND_NOT_VALID 0x00000004 +#define MIIMIND_SCAN 0x00000002 +#define MIIMIND_BUSY 0x00000001 + +/* UEC UTBIPAR (Ten Bit Interface Physical Address Register) + */ +#define UTBIPAR_PHY_ADDRESS_SHIFT (31 - 31) +#define UTBIPAR_PHY_ADDRESS_MASK 0x0000001f + +/* UEC UESCR (Ethernet Statistics Control Register) + */ +#define UESCR_AUTOZ 0x8000 +#define UESCR_CLRCNT 0x4000 +#define UESCR_MAXCOV_SHIFT (15 - 7) +#define UESCR_SCOV_SHIFT (15 - 15) + +/****** Tx data struct collection ******/ +/* Tx thread data, each Tx thread has one this struct. */ +struct uec_thread_data_tx { + u8 res0[136]; +} __packed; + +/* Tx thread parameter, each Tx thread has one this struct. */ +struct uec_thread_tx_pram { + u8 res0[64]; +} __packed; + +/* Send queue queue-descriptor, each Tx queue has one this QD */ +struct uec_send_queue_qd { + u32 bd_ring_base; /* pointer to BD ring base address */ + u8 res0[0x8]; + u32 last_bd_completed_address; /* last entry in BD ring */ + u8 res1[0x30]; +} __packed; + +/* Send queue memory region */ +struct uec_send_queue_mem_region { + struct uec_send_queue_qd sqqd[MAX_TX_QUEUES]; +} __packed; + +/* Scheduler struct */ +struct uec_scheduler { + u16 cpucount0; /* CPU packet counter */ + u16 cpucount1; /* CPU packet counter */ + u16 cecount0; /* QE packet counter */ + u16 cecount1; /* QE packet counter */ + u16 cpucount2; /* CPU packet counter */ + u16 cpucount3; /* CPU packet counter */ + u16 cecount2; /* QE packet counter */ + u16 cecount3; /* QE packet counter */ + u16 cpucount4; /* CPU packet counter */ + u16 cpucount5; /* CPU packet counter */ + u16 cecount4; /* QE packet counter */ + u16 cecount5; /* QE packet counter */ + u16 cpucount6; /* CPU packet counter */ + u16 cpucount7; /* CPU packet counter */ + u16 cecount6; /* QE packet counter */ + u16 cecount7; /* QE packet counter */ + u32 weightstatus[MAX_TX_QUEUES]; /* accumulated weight factor */ + u32 rtsrshadow; /* temporary variable handled by QE */ + u32 time; /* temporary variable handled by QE */ + u32 ttl; /* temporary variable handled by QE */ + u32 mblinterval; /* max burst length interval */ + u16 nortsrbytetime; /* normalized value of byte time in tsr units */ + u8 fracsiz; + u8 res0[1]; + u8 strictpriorityq; /* Strict Priority Mask register */ + u8 txasap; /* Transmit ASAP register */ + u8 extrabw; /* Extra BandWidth register */ + u8 oldwfqmask; /* temporary variable handled by QE */ + u8 weightfactor[MAX_TX_QUEUES]; /**< weight factor for queues */ + u32 minw; /* temporary variable handled by QE */ + u8 res1[0x70 - 0x64]; +} __packed; + +/* Tx firmware counters */ +struct uec_tx_firmware_statistics_pram { + u32 sicoltx; /* single collision */ + u32 mulcoltx; /* multiple collision */ + u32 latecoltxfr; /* late collision */ + u32 frabortduecol; /* frames aborted due to tx collision */ + u32 frlostinmactxer; /* frames lost due to internal MAC error tx */ + u32 carriersenseertx; /* carrier sense error */ + u32 frtxok; /* frames transmitted OK */ + u32 txfrexcessivedefer; + u32 txpkts256; /* total packets(including bad) 256~511 B */ + u32 txpkts512; /* total packets(including bad) 512~1023B */ + u32 txpkts1024; /* total packets(including bad) 1024~1518B */ + u32 txpktsjumbo; /* total packets(including bad) >1024 */ +} __packed; + +/* Tx global parameter table */ +struct uec_tx_global_pram { + u16 temoder; + u8 res0[0x38 - 0x02]; + u32 sqptr; + u32 schedulerbasepointer; + u32 txrmonbaseptr; + u32 tstate; + u8 iphoffset[MAX_IPH_OFFSET_ENTRY]; + u32 vtagtable[0x8]; + u32 tqptr; + u8 res2[0x80 - 0x74]; +} __packed; + +/****** Rx data struct collection ******/ +/* Rx thread data, each Rx thread has one this struct. */ +struct uec_thread_data_rx { + u8 res0[40]; +} __packed; + +/* Rx thread parameter, each Rx thread has one this struct. */ +struct uec_thread_rx_pram { + u8 res0[128]; +} __packed; + +/* Rx firmware counters */ +struct uec_rx_firmware_statistics_pram { + u32 frrxfcser; /* frames with crc error */ + u32 fraligner; /* frames with alignment error */ + u32 inrangelenrxer; /* in range length error */ + u32 outrangelenrxer; /* out of range length error */ + u32 frtoolong; /* frame too long */ + u32 runt; /* runt */ + u32 verylongevent; /* very long event */ + u32 symbolerror; /* symbol error */ + u32 dropbsy; /* drop because of BD not ready */ + u8 res0[0x8]; + u32 mismatchdrop; /* drop because of MAC filtering */ + u32 underpkts; /* total frames less than 64 octets */ + u32 pkts256; /* total frames(including bad)256~511 B */ + u32 pkts512; /* total frames(including bad)512~1023 B */ + u32 pkts1024; /* total frames(including bad)1024~1518 B */ + u32 pktsjumbo; /* total frames(including bad) >1024 B */ + u32 frlossinmacer; + u32 pausefr; /* pause frames */ + u8 res1[0x4]; + u32 removevlan; + u32 replacevlan; + u32 insertvlan; +} __packed; + +/* Rx interrupt coalescing entry, each Rx queue has one this entry. */ +struct uec_rx_interrupt_coalescing_entry { + u32 maxvalue; + u32 counter; +} __packed; + +struct uec_rx_interrupt_coalescing_table { + struct uec_rx_interrupt_coalescing_entry entry[MAX_RX_QUEUES]; +} __packed; + +/* RxBD queue entry, each Rx queue has one this entry. */ +struct uec_rx_bd_queues_entry { + u32 bdbaseptr; /* BD base pointer */ + u32 bdptr; /* BD pointer */ + u32 externalbdbaseptr; /* external BD base pointer */ + u32 externalbdptr; /* external BD pointer */ +} __packed; + +/* Rx global parameter table */ +struct uec_rx_global_pram { + u32 remoder; /* ethernet mode reg. */ + u32 rqptr; /* base pointer to the Rx Queues */ + u32 res0[0x1]; + u8 res1[0x20 - 0xc]; + u16 typeorlen; + u8 res2[0x1]; + u8 rxgstpack; /* ack on GRACEFUL STOP RX command */ + u32 rxrmonbaseptr; /* Rx RMON statistics base */ + u8 res3[0x30 - 0x28]; + u32 intcoalescingptr; /* Interrupt coalescing table pointer */ + u8 res4[0x36 - 0x34]; + u8 rstate; + u8 res5[0x46 - 0x37]; + u16 mrblr; /* max receive buffer length reg. */ + u32 rbdqptr; /* RxBD parameter table description */ + u16 mflr; /* max frame length reg. */ + u16 minflr; /* min frame length reg. */ + u16 maxd1; /* max dma1 length reg. */ + u16 maxd2; /* max dma2 length reg. */ + u32 ecamptr; /* external CAM address */ + u32 l2qt; /* VLAN priority mapping table. */ + u32 l3qt[0x8]; /* IP priority mapping table. */ + u16 vlantype; /* vlan type */ + u16 vlantci; /* default vlan tci */ + u8 addressfiltering[64];/* address filtering data structure */ + u32 exf_global_param; /* extended filtering global parameters */ + u8 res6[0x100 - 0xc4]; /* Initialize to zero */ +} __packed; + +#define GRACEFUL_STOP_ACKNOWLEDGE_RX 0x01 + +/****** UEC common ******/ +/* UCC statistics - hardware counters */ +struct uec_hardware_statistics { + u32 tx64; + u32 tx127; + u32 tx255; + u32 rx64; + u32 rx127; + u32 rx255; + u32 txok; + u16 txcf; + u32 tmca; + u32 tbca; + u32 rxfok; + u32 rxbok; + u32 rbyt; + u32 rmca; + u32 rbca; +} __packed; + +/* InitEnet command parameter */ +struct uec_init_cmd_pram { + u8 resinit0; + u8 resinit1; + u8 resinit2; + u8 resinit3; + u16 resinit4; + u8 res1[0x1]; + u8 largestexternallookupkeysize; + u32 rgftgfrxglobal; + u32 rxthread[MAX_ENET_INIT_PARAM_ENTRIES_RX]; /* rx threads */ + u8 res2[0x38 - 0x30]; + u32 txglobal; /* tx global */ + u32 txthread[MAX_ENET_INIT_PARAM_ENTRIES_TX]; /* tx threads */ + u8 res3[0x1]; +} __packed; + +#define ENET_INIT_PARAM_RGF_SHIFT (32 - 4) +#define ENET_INIT_PARAM_TGF_SHIFT (32 - 8) + +#define ENET_INIT_PARAM_RISC_MASK 0x0000003f +#define ENET_INIT_PARAM_PTR_MASK 0x00ffffc0 +#define ENET_INIT_PARAM_SNUM_MASK 0xff000000 +#define ENET_INIT_PARAM_SNUM_SHIFT 24 + +#define ENET_INIT_PARAM_MAGIC_RES_INIT0 0x06 +#define ENET_INIT_PARAM_MAGIC_RES_INIT1 0x30 +#define ENET_INIT_PARAM_MAGIC_RES_INIT2 0xff +#define ENET_INIT_PARAM_MAGIC_RES_INIT3 0x00 +#define ENET_INIT_PARAM_MAGIC_RES_INIT4 0x0400 + +/* structure representing 82xx Address Filtering Enet Address in PRAM */ +struct uec_82xx_enet_addr { + u8 res1[0x2]; + u16 h; /* address (MSB) */ + u16 m; /* address */ + u16 l; /* address (LSB) */ +} __packed; + +/* structure representing 82xx Address Filtering PRAM */ +struct uec_82xx_add_filtering_pram { + u32 iaddr_h; /* individual address filter, high */ + u32 iaddr_l; /* individual address filter, low */ + u32 gaddr_h; /* group address filter, high */ + u32 gaddr_l; /* group address filter, low */ + struct uec_82xx_enet_addr taddr; + struct uec_82xx_enet_addr paddr[4]; + u8 res0[0x40 - 0x38]; +} __packed; + +/* Buffer Descriptor */ +struct buffer_descriptor { + u16 status; + u16 len; + u32 data; +} __packed; + +#define SIZEOFBD sizeof(struct buffer_descriptor) + +/* Common BD flags */ +#define BD_WRAP 0x2000 +#define BD_INT 0x1000 +#define BD_LAST 0x0800 +#define BD_CLEAN 0x3000 + +/* TxBD status flags */ +#define TX_BD_READY 0x8000 +#define TX_BD_PADCRC 0x4000 +#define TX_BD_WRAP BD_WRAP +#define TX_BD_INT BD_INT +#define TX_BD_LAST BD_LAST +#define TX_BD_TXCRC 0x0400 +#define TX_BD_DEF 0x0200 +#define TX_BD_PP 0x0100 +#define TX_BD_LC 0x0080 +#define TX_BD_RL 0x0040 +#define TX_BD_RC 0x003C +#define TX_BD_UNDERRUN 0x0002 +#define TX_BD_TRUNC 0x0001 + +#define TX_BD_ERROR (TX_BD_UNDERRUN | TX_BD_TRUNC) + +/* RxBD status flags */ +#define RX_BD_EMPTY 0x8000 +#define RX_BD_OWNER 0x4000 +#define RX_BD_WRAP BD_WRAP +#define RX_BD_INT BD_INT +#define RX_BD_LAST BD_LAST +#define RX_BD_FIRST 0x0400 +#define RX_BD_CMR 0x0200 +#define RX_BD_MISS 0x0100 +#define RX_BD_BCAST 0x0080 +#define RX_BD_MCAST 0x0040 +#define RX_BD_LG 0x0020 +#define RX_BD_NO 0x0010 +#define RX_BD_SHORT 0x0008 +#define RX_BD_CRCERR 0x0004 +#define RX_BD_OVERRUN 0x0002 +#define RX_BD_IPCH 0x0001 + +#define RX_BD_ERROR (RX_BD_LG | RX_BD_NO | RX_BD_SHORT | \ + RX_BD_CRCERR | RX_BD_OVERRUN) + +/* BD access macros */ +#define BD_STATUS(_bd) (in_be16(&((_bd)->status))) +#define BD_STATUS_SET(_bd, _v) (out_be16(&((_bd)->status), _v)) +#define BD_LENGTH(_bd) (in_be16(&((_bd)->len))) +#define BD_LENGTH_SET(_bd, _v) (out_be16(&((_bd)->len), _v)) +#define BD_DATA_CLEAR(_bd) (out_be32(&((_bd)->data), 0)) +#define BD_DATA(_bd) ((u8 *)(((_bd)->data))) +#define BD_DATA_SET(_bd, _data) (out_be32(&((_bd)->data), (u32)_data)) +#define BD_ADVANCE(_bd, _status, _base) \ + (((_status) & BD_WRAP) ? (_bd) = \ + ((struct buffer_descriptor *)(_base)) : ++(_bd)) + +/* Rx Prefetched BDs */ +struct uec_rx_pref_bds { + struct buffer_descriptor bd[MAX_PREFETCHED_BDS]; /* prefetched bd */ +} __packed; + +/* Alignments */ +#define UEC_RX_GLOBAL_PRAM_ALIGNMENT 64 +#define UEC_TX_GLOBAL_PRAM_ALIGNMENT 64 +#define UEC_THREAD_RX_PRAM_ALIGNMENT 128 +#define UEC_THREAD_TX_PRAM_ALIGNMENT 64 +#define UEC_THREAD_DATA_ALIGNMENT 256 +#define UEC_SEND_QUEUE_QUEUE_DESCRIPTOR_ALIGNMENT 32 +#define UEC_SCHEDULER_ALIGNMENT 4 +#define UEC_TX_STATISTICS_ALIGNMENT 4 +#define UEC_RX_STATISTICS_ALIGNMENT 4 +#define UEC_RX_INTERRUPT_COALESCING_ALIGNMENT 4 +#define UEC_RX_BD_QUEUES_ALIGNMENT 8 +#define UEC_RX_PREFETCHED_BDS_ALIGNMENT 128 +#define UEC_RX_EXTENDED_FILTERING_GLOBAL_PARAMETERS_ALIGNMENT 4 +#define UEC_RX_BD_RING_ALIGNMENT 32 +#define UEC_TX_BD_RING_ALIGNMENT 32 +#define UEC_MRBLR_ALIGNMENT 128 +#define UEC_RX_BD_RING_SIZE_ALIGNMENT 4 +#define UEC_TX_BD_RING_SIZE_MEMORY_ALIGNMENT 32 +#define UEC_RX_DATA_BUF_ALIGNMENT 64 + +#define UEC_VLAN_PRIORITY_MAX 8 +#define UEC_IP_PRIORITY_MAX 64 +#define UEC_TX_VTAG_TABLE_ENTRY_MAX 8 +#define UEC_RX_BD_RING_SIZE_MIN 8 +#define UEC_TX_BD_RING_SIZE_MIN 2 + +/* TBI / MII Set Register */ +enum enet_tbi_mii_reg { + ENET_TBI_MII_CR = 0x00, + ENET_TBI_MII_SR = 0x01, + ENET_TBI_MII_ANA = 0x04, + ENET_TBI_MII_ANLPBPA = 0x05, + ENET_TBI_MII_ANEX = 0x06, + ENET_TBI_MII_ANNPT = 0x07, + ENET_TBI_MII_ANLPANP = 0x08, + ENET_TBI_MII_EXST = 0x0F, + ENET_TBI_MII_JD = 0x10, + ENET_TBI_MII_TBICON = 0x11 +}; + +/* TBI MDIO register bit fields*/ +#define TBICON_CLK_SELECT 0x0020 +#define TBIANA_ASYMMETRIC_PAUSE 0x0100 +#define TBIANA_SYMMETRIC_PAUSE 0x0080 +#define TBIANA_HALF_DUPLEX 0x0040 +#define TBIANA_FULL_DUPLEX 0x0020 +#define TBICR_PHY_RESET 0x8000 +#define TBICR_ANEG_ENABLE 0x1000 +#define TBICR_RESTART_ANEG 0x0200 +#define TBICR_FULL_DUPLEX 0x0100 +#define TBICR_SPEED1_SET 0x0040 + +#define TBIANA_SETTINGS ( \ + TBIANA_ASYMMETRIC_PAUSE \ + | TBIANA_SYMMETRIC_PAUSE \ + | TBIANA_FULL_DUPLEX \ + ) + +#define TBICR_SETTINGS ( \ + TBICR_PHY_RESET \ + | TBICR_ANEG_ENABLE \ + | TBICR_FULL_DUPLEX \ + | TBICR_SPEED1_SET \ + ) + +/* UEC number of threads */ +enum uec_num_of_threads { + UEC_NUM_OF_THREADS_1 = 0x1, /* 1 */ + UEC_NUM_OF_THREADS_2 = 0x2, /* 2 */ + UEC_NUM_OF_THREADS_4 = 0x0, /* 4 */ + UEC_NUM_OF_THREADS_6 = 0x3, /* 6 */ + UEC_NUM_OF_THREADS_8 = 0x4 /* 8 */ +}; + +/* UEC initialization info struct */ +#define STD_UEC_INFO(num) \ +{ \ + .uf_info = { \ + .ucc_num = CONFIG_SYS_UEC##num##_UCC_NUM,\ + .rx_clock = CONFIG_SYS_UEC##num##_RX_CLK, \ + .tx_clock = CONFIG_SYS_UEC##num##_TX_CLK, \ + .eth_type = CONFIG_SYS_UEC##num##_ETH_TYPE,\ + }, \ + .num_threads_tx = UEC_NUM_OF_THREADS_1, \ + .num_threads_rx = UEC_NUM_OF_THREADS_1, \ + .risc_tx = QE_RISC_ALLOCATION_RISC1_AND_RISC2, \ + .risc_rx = QE_RISC_ALLOCATION_RISC1_AND_RISC2, \ + .tx_bd_ring_len = 16, \ + .rx_bd_ring_len = 16, \ + .phy_address = CONFIG_SYS_UEC##num##_PHY_ADDR, \ + .enet_interface_type = CONFIG_SYS_UEC##num##_INTERFACE_TYPE, \ + .speed = CONFIG_SYS_UEC##num##_INTERFACE_SPEED, \ +} + +struct uec_inf { + struct ucc_fast_inf uf_info; + enum uec_num_of_threads num_threads_tx; + enum uec_num_of_threads num_threads_rx; + unsigned int risc_tx; + unsigned int risc_rx; + u16 rx_bd_ring_len; + u16 tx_bd_ring_len; + u8 phy_address; + phy_interface_t enet_interface_type; + int speed; +}; + +/* UEC driver initialized info */ +#define MAX_RXBUF_LEN 1536 +#define MAX_FRAME_LEN 1518 +#define MIN_FRAME_LEN 64 +#define MAX_DMA1_LEN 1520 +#define MAX_DMA2_LEN 1520 + +/* UEC driver private struct */ +struct uec_priv { + struct uec_inf *uec_info; + struct ucc_fast_priv *uccf; + struct eth_device *dev; + uec_t *uec_regs; + /* enet init command parameter */ + struct uec_init_cmd_pram *p_init_enet_param; + u32 init_enet_param_offset; + /* Rx and Tx parameter */ + struct uec_rx_global_pram *p_rx_glbl_pram; + u32 rx_glbl_pram_offset; + struct uec_tx_global_pram *p_tx_glbl_pram; + u32 tx_glbl_pram_offset; + struct uec_send_queue_mem_region *p_send_q_mem_reg; + u32 send_q_mem_reg_offset; + struct uec_thread_data_tx *p_thread_data_tx; + u32 thread_dat_tx_offset; + struct uec_thread_data_rx *p_thread_data_rx; + u32 thread_dat_rx_offset; + struct uec_rx_bd_queues_entry *p_rx_bd_qs_tbl; + u32 rx_bd_qs_tbl_offset; + /* BDs specific */ + u8 *p_tx_bd_ring; + u32 tx_bd_ring_offset; + u8 *p_rx_bd_ring; + u32 rx_bd_ring_offset; + u8 *p_rx_buf; + u32 rx_buf_offset; + struct buffer_descriptor *tx_bd; + struct buffer_descriptor *rx_bd; + /* Status */ + int mac_tx_enabled; + int mac_rx_enabled; + int grace_stopped_tx; + int grace_stopped_rx; + int the_first_run; +#if !defined(COFIG_DM) + /* PHY specific */ + struct uec_mii_info *mii_info; + int oldspeed; + int oldduplex; + int oldlink; +#endif +}; + +int uec_initialize(struct bd_info *bis, struct uec_inf *uec_info); +int uec_eth_init(struct bd_info *bis, struct uec_inf *uecs, int num); +int uec_standard_init(struct bd_info *bis); +#endif /* __UEC_H__ */ diff --git a/drivers/qe/Kconfig b/drivers/qe/Kconfig index 44c9f010bd..864b36b822 100644 --- a/drivers/qe/Kconfig +++ b/drivers/qe/Kconfig @@ -3,7 +3,7 @@ # config QE bool "Enable support for QUICC Engine" - depends on PPC && !DM_ETH + depends on PPC default y if ARCH_T1040 || ARCH_T1042 || ARCH_T1024 || ARCH_P1021 \ || ARCH_P1025 help diff --git a/drivers/qe/uccf.c b/drivers/qe/uccf.c index 306f1ea1db..d5d734439c 100644 --- a/drivers/qe/uccf.c +++ b/drivers/qe/uccf.c @@ -14,6 +14,7 @@ #include "uccf.h" #include +#if !defined(CONFIG_DM_ETH) void ucc_fast_transmit_on_demand(struct ucc_fast_priv *uccf) { out_be16(&uccf->uf_regs->utodr, UCC_FAST_TOD); @@ -505,3 +506,4 @@ int ucc_fast_init(struct ucc_fast_inf *uf_info, *uccf_ret = uccf; return 0; } +#endif diff --git a/drivers/qe/uec.c b/drivers/qe/uec.c index cfd5397044..5da971ddc0 100644 --- a/drivers/qe/uec.c +++ b/drivers/qe/uec.c @@ -20,6 +20,7 @@ #include #include +#if !defined(CONFIG_DM_ETH) /* Default UTBIPAR SMI address */ #ifndef CONFIG_UTBIPAR_INIT_TBIPA #define CONFIG_UTBIPAR_INIT_TBIPA 0x1F @@ -1432,3 +1433,4 @@ int uec_standard_init(struct bd_info *bis) { return uec_eth_init(bis, uec_info, ARRAY_SIZE(uec_info)); } +#endif diff --git a/drivers/qe/uec_phy.c b/drivers/qe/uec_phy.c index b5ca5f76f9..9d429c832f 100644 --- a/drivers/qe/uec_phy.c +++ b/drivers/qe/uec_phy.c @@ -23,6 +23,8 @@ #include #include +#if !defined(CONFIG_DM_ETH) + #define ugphy_printk(format, arg...) \ printf(format "\n", ## arg) @@ -925,3 +927,4 @@ void change_phy_interface_mode(struct eth_device *dev, marvell_phy_interface_mode(dev, type, speed); #endif } +#endif