From: Marek Vasut Date: Sat, 27 Apr 2024 22:20:38 +0000 (+0200) Subject: ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC board X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=69374aa86aa2fd6e301f7e4acfd2f3fb4441c68a;p=u-boot.git ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC board This stm32mp135f-dhcor-dhsbc board is a stack of DHCOR SoM based on STM32MP135F SoC (900MHz / crypto capabilities) populated on DHSBC carrier board. The SoM contains the following peripherals: - STPMIC (power delivery) - 512MB DDR3L memory - eMMC and SDIO WiFi module The DHSBC carrier board contains the following peripherals: - Two RGMII Ethernet ports - USB-A Host port, USB-C peripheral port, USB-C power supply plug - Expansion connector Reviewed-by: Patrice Chotard Signed-off-by: Marek Vasut --- diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 2be36cf1d7..e034668d75 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -1134,6 +1134,7 @@ dtb-$(CONFIG_ASPEED_AST2600) += \ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb dtb-$(CONFIG_STM32MP13X) += \ + stm32mp135f-dhcor-dhsbc.dtb \ stm32mp135f-dk.dtb dtb-$(CONFIG_STM32MP15X) += \ diff --git a/arch/arm/dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi b/arch/arm/dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi new file mode 100644 index 0000000000..d718aae16c --- /dev/null +++ b/arch/arm/dts/stm32mp135f-dhcor-dhsbc-u-boot.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2024 Marek Vasut + */ + +#include "stm32mp13xx-dhcor-u-boot.dtsi" + +&uart4 { + bootph-all; +}; + +&uart4_pins_b { + bootph-all; + + pins1 { + bootph-all; + }; + pins2 { + bootph-all; + }; +}; + +&usbphyc { + bootph-all; +}; diff --git a/arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts b/arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts new file mode 100644 index 0000000000..fc1c48ad56 --- /dev/null +++ b/arch/arm/dts/stm32mp135f-dhcor-dhsbc.dts @@ -0,0 +1,383 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2024 Marek Vasut + * + * DHCOR STM32MP13 variant: + * DHCR-STM32MP135F-C100-R051-EE-F0409-SPI4-RTC-WBT-I-01LG + * DHCOR PCB number: 718-100 or newer + * DHSBC PCB number: 719-100 or newer + */ + +/dts-v1/; + +#include +#include "stm32mp135.dtsi" +#include "stm32mp13xf.dtsi" +#include "stm32mp13xx-dhcor-som.dtsi" + +/ { + model = "DH electronics STM32MP135F DHCOR DHSBC"; + compatible = "dh,stm32mp135f-dhcor-dhsbc", + "dh,stm32mp135f-dhcor-som", + "st,stm32mp135"; + + aliases { + ethernet0 = ð1; + ethernet1 = ð2; + serial2 = &usart1; + serial3 = &usart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&adc_1 { + pinctrl-names = "default"; + pinctrl-0 = <&adc1_pins_a &adc1_usb_cc_pins_b>; + vdda-supply = <&vdd_adc>; + vref-supply = <&vdd_adc>; + status = "okay"; + + adc1: adc@0 { + status = "okay"; + + /* + * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in2 & in11. + * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C: + * 5 * (5.1 + 47kOhms) * 5pF => 1.3us. + * Use arbitrary margin here (e.g. 5us). + * + * The pinmux pins must be set as ANALOG, use datasheet + * DS13483 Table 7. STM32MP135C/F ball definitions to + * find out which 'pin name' maps to which 'additional + * functions', which lists the mapping between pin and + * ADC channel. In this case, PA5 maps to ADC1_INP2 and + * PF13 maps to ADC1_INP11 . + */ + channel@2 { + reg = <2>; + st,min-sample-time-ns = <5000>; + }; + + channel@11 { + reg = <11>; + st,min-sample-time-ns = <5000>; + }; + + /* Expansion connector: INP12:pin29 */ + channel@12 { + reg = <12>; + st,min-sample-time-ns = <5000>; + }; + }; +}; + +ð1 { + status = "okay"; + pinctrl-0 = <ð1_rgmii_pins_a>; + pinctrl-1 = <ð1_rgmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii-id"; + phy-handle = <ðphy1>; + st,ext-phyclk; + nvmem-cells = <ðernet_mac1_address>; + nvmem-cell-names = "mac-address"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + ethphy1: ethernet-phy@1 { + /* RTL8211F */ + compatible = "ethernet-phy-id001c.c916", + "ethernet-phy-ieee802.3-c22"; + interrupt-parent = <&gpiog>; + interrupts = <12 IRQ_TYPE_LEVEL_LOW>; + reg = <1>; + reset-assert-us = <15000>; + reset-deassert-us = <55000>; + reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð2 { + status = "okay"; + pinctrl-0 = <ð2_rgmii_pins_a>; + pinctrl-1 = <ð2_rgmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rgmii-id"; + phy-handle = <ðphy2>; + st,ext-phyclk; + nvmem-cells = <ðernet_mac2_address>; + nvmem-cell-names = "mac-address"; + + mdio1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + ethphy2: ethernet-phy@1 { + /* RTL8211F */ + compatible = "ethernet-phy-id001c.c916", + "ethernet-phy-ieee802.3-c22"; + interrupt-parent = <&gpiog>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + reg = <1>; + reset-assert-us = <15000>; + reset-deassert-us = <55000>; + reset-gpios = <&gpiog 8 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpioa { + gpio-line-names = "", "", "", "", + "", "DHSBC_USB_PWR_CC1", "", "", + "", "", "", "DHSBC_nETH1_RST", + "", "DHCOR_HW-CODING_0", "", ""; +}; + +&gpiob { + gpio-line-names = "", "", "", "", + "", "", "", "DHCOR_BT_HOST_WAKE", + "", "", "", "", + "", "DHSBC_nTPM_CS", "", ""; +}; + +&gpioc { + gpio-line-names = "", "", "", "DHSBC_USB_5V_MEAS", + "", "", "", "", + "", "", "", "", + "", "", "", ""; +}; + +&gpiod { + gpio-line-names = "", "", "", "", + "", "DHCOR_RAM-CODING_0", "", "", + "", "DHCOR_RAM-CODING_1", "", "", + "", "", "", ""; +}; + +&gpioe { + gpio-line-names = "", "", "", "", + "", "", "", "", + "", "DHSBC_nTPM_RST", "", "", + "DHSBC_nTPM_PIRQ", "", "DHCOR_WL_HOST_WAKE", ""; +}; + +&gpiof { + gpio-line-names = "", "", "DHSBC_USB_PWR_nFLT", "", + "", "", "", "", + "", "", "", "", + "DHCOR_WL_REG_ON", "DHSBC_USB_PWR_CC2", "", ""; +}; + +&gpiog { + gpio-line-names = "", "", "", "", + "", "", "", "", + "DHSBC_nETH2_RST", "DHCOR_BT_DEV_WAKE", "", "", + "DHSBC_ETH1_INTB", "", "", "DHSBC_ETH2_INTB"; +}; + +&gpioi { + gpio-line-names = "DHCOR_RTC_nINT", "DHCOR_HW-CODING_1", + "DHCOR_BT_REG_ON", "DHCOR_PMIC_nINT", + "DHSBC_BOOT0", "DHSBC_BOOT1", + "DHSBC_BOOT2", "DHSBC_USB-C_DATA_VBUS"; +}; + +&i2c1 { /* Expansion connector: SDA:pin27 SCL:pin28 */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c1_pins_a>; + pinctrl-1 = <&i2c1_sleep_pins_a>; + i2c-scl-rising-time-ns = <96>; + i2c-scl-falling-time-ns = <3>; + clock-frequency = <400000>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; +}; + +&i2c5 { /* Expansion connector: SDA:pin3 SCL:pin5 */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c5_pins_b>; + pinctrl-1 = <&i2c5_sleep_pins_b>; + i2c-scl-rising-time-ns = <96>; + i2c-scl-falling-time-ns = <3>; + clock-frequency = <400000>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; +}; + +&m_can1 { /* Expansion connector: TX:pin16 RX:pin18 */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can1_pins_a>; + pinctrl-1 = <&m_can1_sleep_pins_a>; + status = "okay"; +}; + +&m_can2 { /* Expansion connector: TX:pin22 RX:pin26 */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&m_can2_pins_a>; + pinctrl-1 = <&m_can2_sleep_pins_a>; + status = "okay"; +}; + +&pwr_regulators { + vdd-supply = <&vdd>; + vdd_3v3_usbfs-supply = <&vdd_usb>; + status = "okay"; +}; + +&sai1 { /* Expansion connector: SCK-A:pin12 FS-A:pin35 SD-A:pin38 SD-B:pin40 */ + clocks = <&rcc SAI1>, <&rcc PLL3_Q>, <&rcc PLL3_R>; + clock-names = "pclk", "x8k", "x11k"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sai1a_pins_a &sai1b_pins_a>; + pinctrl-1 = <&sai1a_sleep_pins_a &sai1b_sleep_pins_a>; +}; + +&scmi_voltd { + status = "disabled"; +}; + +&spi2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&spi2_pins_a>; + pinctrl-1 = <&spi2_sleep_pins_a>; + cs-gpios = <&gpiob 13 0>; + status = "okay"; + + st33htph: tpm@0 { + compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&spi3 { /* Expansion connector: MOSI:pin19 MISO:pin21 SCK:pin22 nCS:pin24 */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&spi3_pins_a>; + pinctrl-1 = <&spi3_sleep_pins_a>; + cs-gpios = <&gpiof 3 0>; + status = "disabled"; +}; + +&timers5 { /* Expansion connector: CH3:pin31 */ + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; + + pwm { + pinctrl-0 = <&pwm5_pins_a>; + pinctrl-1 = <&pwm5_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + status = "okay"; + }; + timer@4 { + status = "okay"; + }; +}; + +&timers13 { /* Expansion connector: CH1:pin32 */ + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; + + pwm { + pinctrl-0 = <&pwm13_pins_a>; + pinctrl-1 = <&pwm13_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + status = "okay"; + }; + timer@12 { + status = "okay"; + }; +}; + +&usart1 { /* Expansion connector: RX:pin33 TX:pin37 */ + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&usart1_pins_b>; + pinctrl-1 = <&usart1_sleep_pins_b>; + pinctrl-2 = <&usart1_idle_pins_b>; + status = "okay"; +}; + +&usart2 { /* Expansion connector: RX:pin10 TX:pin8 RTS:pin11 CTS:pin36 */ + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&usart2_pins_b>; + pinctrl-1 = <&usart2_sleep_pins_b>; + pinctrl-2 = <&usart2_idle_pins_b>; + uart-has-rtscts; + status = "okay"; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + status = "okay"; +}; + +&usbh_ohci { + phys = <&usbphyc_port0>; + status = "okay"; +}; + +&usbotg_hs { + dr_mode = "peripheral"; + phys = <&usbphyc_port1 0>; + phy-names = "usb2-phy"; + usb33d-supply = <&usb33>; + status = "okay"; +}; + +&usbphyc { + status = "okay"; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; + st,current-boost-microamp = <1000>; + st,decrease-hs-slew-rate; + st,tune-hs-dc-level = <2>; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <11>; + st,trim-hs-impedance = <2>; + st,tune-squelch-level = <1>; + st,enable-hs-rx-gain-eq; + st,no-hs-ftime-ctrl; + st,no-lsfs-sc; + connector { + compatible = "usb-a-connector"; + vbus-supply = <&vbus_sw>; + }; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; + st,current-boost-microamp = <1000>; + st,decrease-hs-slew-rate; + st,tune-hs-dc-level = <2>; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <11>; + st,trim-hs-impedance = <2>; + st,tune-squelch-level = <1>; + st,enable-hs-rx-gain-eq; + st,no-hs-ftime-ctrl; + st,no-lsfs-sc; + connector { + compatible = "gpio-usb-b-connector", "usb-b-connector"; + vbus-gpios = <&gpioi 7 GPIO_ACTIVE_HIGH>; + label = "Type-C"; + self-powered; + type = "micro"; + }; +}; diff --git a/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi b/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi new file mode 100644 index 0000000000..ddad649777 --- /dev/null +++ b/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi @@ -0,0 +1,308 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2024 Marek Vasut + */ + +#include +#include +#include +#include +#include +#include "stm32mp13-pinctrl.dtsi" + +/ { + model = "DH electronics STM32MP13xx DHCOR SoM"; + compatible = "dh,stm32mp131a-dhcor-som", + "st,stm32mp131"; + + aliases { + mmc0 = &sdmmc2; + mmc1 = &sdmmc1; + serial0 = &uart4; + serial1 = &uart7; + rtc0 = &rv3032; + spi0 = &qspi; + }; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x20000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + optee@dd000000 { + reg = <0xdd000000 0x3000000>; + no-map; + }; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpiof 12 GPIO_ACTIVE_LOW>; + }; + + vin: vin { + compatible = "regulator-fixed"; + regulator-name = "vin"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&i2c3 { + i2c-scl-rising-time-ns = <96>; + i2c-scl-falling-time-ns = <3>; + clock-frequency = <400000>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&gpioi 3 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay"; + + regulators { + compatible = "st,stpmic1-regulators"; + + ldo1-supply = <&vin>; + ldo2-supply = <&vin>; + ldo3-supply = <&vin>; + ldo4-supply = <&vin>; + ldo5-supply = <&vin>; + ldo6-supply = <&vin>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcpu: buck1 { /* VDD_CPU_1V2 */ + regulator-name = "vddcpu"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { /* VDD_DDR_1V35 */ + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { /* VDD_3V3_1V8 */ + regulator-name = "vdd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vddcore: buck4 { /* VDD_CORE_1V2 */ + regulator-name = "vddcore"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_adc: ldo1 { /* VDD_ADC_1V8 */ + regulator-name = "vdd_adc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = ; + }; + + vdd_ldo2: ldo2 { /* LDO2_OUT_1V8 */ + regulator-name = "vdd_ldo2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = ; + }; + + vdd_ldo3: ldo3 { /* LDO3_OUT */ + regulator-name = "vdd_ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = ; + }; + + vdd_usb: ldo4 { /* VDD_USB_3V3 */ + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + interrupts = ; + }; + + vdd_sd: ldo5 { /* VDD_SD_3V3_1V8 */ + regulator-name = "vdd_sd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + interrupts = ; + }; + + vdd_sd2: ldo6 { /* VDD_SD2_3V3_1V8 */ + regulator-name = "vdd_sd2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + interrupts = ; + }; + + vref_ddr: vref_ddr { /* VREF_DDR_0V675 */ + regulator-name = "vref_ddr"; + regulator-always-on; + }; + + bst_out: boost { /* BST_OUT_5V2 */ + regulator-name = "bst_out"; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = ; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = ; + regulator-active-discharge = <1>; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = , ; + interrupt-names = "onkey-falling", "onkey-rising"; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; + + eeprom0: eeprom@50 { + compatible = "atmel,24c256"; /* ST M24256 */ + reg = <0x50>; + pagesize = <64>; + }; + + rv3032: rtc@51 { + compatible = "microcrystal,rv3032"; + reg = <0x51>; + interrupts-extended = <&gpioi 0 IRQ_TYPE_EDGE_FALLING>; + }; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&qspi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk_pins_a + &qspi_bk1_pins_a + &qspi_cs1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a + &qspi_bk1_sleep_pins_a + &qspi_cs1_sleep_pins_a>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash0: flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +/* Console UART */ +&uart4 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&uart4_pins_b>; + pinctrl-1 = <&uart4_sleep_pins_b>; + pinctrl-2 = <&uart4_idle_pins_b>; + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; +}; + +/* Bluetooth */ +&uart7 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&uart7_pins_a>; + pinctrl-1 = <&uart7_sleep_pins_a>; + pinctrl-2 = <&uart7_idle_pins_a>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "infineon,cyw43439-bt", "brcm,bcm4329-bt"; + max-speed = <3000000>; + device-wakeup-gpios = <&gpiog 9 GPIO_ACTIVE_HIGH>; + shutdown-gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>; + }; +}; + +/* SDIO WiFi */ +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + non-removable; + st,neg-edge; + vmmc-supply = <&vdd>; + mmc-pwrseq = <&sdio_pwrseq>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + + brcmf: bcrmf@1 { /* muRata 1YN */ + reg = <1>; + compatible = "infineon,cyw43439-fmac", "brcm,bcm4329-fmac"; + interrupt-parent = <&gpioe>; + interrupts = <14 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host-wake"; + }; +}; + +/* eMMC */ +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>; + bus-width = <8>; + mmc-ddr-3_3v; + no-sd; + no-sdio; + non-removable; + st,neg-edge; + vmmc-supply = <&vdd>; + vqmmc-supply = <&vdd>; + status = "okay"; +}; diff --git a/arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi b/arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi new file mode 100644 index 0000000000..30e3b91bcc --- /dev/null +++ b/arch/arm/dts/stm32mp13xx-dhcor-u-boot.dtsi @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2024 Marek Vasut + */ + +#include "stm32mp13-u-boot.dtsi" + +/ { + aliases { + eeprom0 = &eeprom0; + }; + + config { + dh,ddr3-coding-gpios = <&gpiod 5 0>, <&gpiod 9 0>; + dh,som-coding-gpios = <&gpioa 13 0>, <&gpioi 1 0>; + }; +}; + +&flash0 { + bootph-pre-ram; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "fsbl1"; + reg = <0x00000000 0x00040000>; + }; + partition@40000 { + label = "fsbl2"; + reg = <0x00040000 0x00040000>; + }; + partition@80000 { + label = "u-boot"; + reg = <0x00080000 0x00360000>; + }; + partition@3e0000 { + label = "u-boot-env-a"; + reg = <0x003e0000 0x00010000>; + }; + partition@3f0000 { + label = "u-boot-env-b"; + reg = <0x003f0000 0x00010000>; + }; + }; +}; + +&sdmmc1 { + status = "disabled"; +}; + +&usbotg_hs { + u-boot,force-b-session-valid; +}; diff --git a/configs/stm32mp13_dhcor_defconfig b/configs/stm32mp13_dhcor_defconfig new file mode 100644 index 0000000000..fb3d86deb6 --- /dev/null +++ b/configs/stm32mp13_dhcor_defconfig @@ -0,0 +1,148 @@ +CONFIG_ARM=y +CONFIG_ARCH_STM32MP=y +CONFIG_TFABOOT=y +CONFIG_SYS_MALLOC_F_LEN=0x1c0000 +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc0400000 +CONFIG_ENV_SIZE=0x4000 +CONFIG_ENV_OFFSET=0x3E0000 +CONFIG_ENV_SECT_SIZE=0x1000 +CONFIG_DEFAULT_DEVICE_TREE="stm32mp135f-dhcor-dhsbc" +CONFIG_STM32MP13X=y +CONFIG_DDR_CACHEABLE_SIZE=0x8000000 +CONFIG_CMD_STM32KEY=y +CONFIG_TARGET_ST_STM32MP13X=y +CONFIG_ENV_OFFSET_REDUND=0x3F0000 +CONFIG_CMD_STM32PROG=y +CONFIG_STM32MP15_PWR=y +# CONFIG_ARMV7_NONSEC is not set +CONFIG_SYS_LOAD_ADDR=0xc2000000 +CONFIG_SYS_MEMTEST_START=0xc0000000 +CONFIG_SYS_MEMTEST_END=0xc4000000 +CONFIG_FIT=y +CONFIG_SYS_BOOTM_LEN=0x2000000 +CONFIG_DISTRO_DEFAULTS=y +CONFIG_BOOTSTAGE_RECORD_COUNT=100 +CONFIG_BOOTDELAY=3 +CONFIG_BOOTCOMMAND="run bootcmd_stm32mp" +CONFIG_SYS_CONSOLE_IS_IN_ENV=y +CONFIG_SYS_PROMPT="STM32MP> " +# CONFIG_CMD_ELF is not set +CONFIG_CMD_ASKENV=y +# CONFIG_CMD_EXPORTENV is not set +CONFIG_CMD_ERASEENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_UNZIP=y +CONFIG_CMD_CLK=y +CONFIG_CMD_DFU=y +CONFIG_CMD_FUSE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_LSBLK=y +CONFIG_CMD_MMC=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_CAT=y +CONFIG_CMD_SETEXPR_FMT=y +CONFIG_CMD_XXD=y +CONFIG_CMD_DHCP6=y +CONFIG_CMD_TFTPPUT=y +CONFIG_SYS_DISABLE_AUTOLOAD=y +CONFIG_CMD_WGET=y +CONFIG_CMD_BOOTCOUNT=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_RNG=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +CONFIG_CMD_BTRFS=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_LOG=y +CONFIG_CMD_UBI=y +# CONFIG_ISO_PARTITION is not set +CONFIG_OF_LIVE=y +CONFIG_ENV_IS_NOWHERE=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_SPI_MAX_HZ=50000000 +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_VERSION_VARIABLE=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_IP_DEFRAG=y +CONFIG_TFTP_TSIZE=y +CONFIG_PROT_TCP_SACK=y +CONFIG_IPV6=y +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_SYS_BOOTCOUNT_MAGIC=0xB0C40000 +CONFIG_CLK_SCMI=y +CONFIG_SET_DFU_ALT_INFO=y +CONFIG_GPIO_HOG=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_STM32F7=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_STM32_FMC2_EBI=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x50 +CONFIG_SUPPORT_EMMC_BOOT=y +CONFIG_STM32_SDMMC2=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_PHY_REALTEK=y +CONFIG_DWC_ETH_QOS=y +CONFIG_PHY=y +CONFIG_PHY_STM32_USBPHYC=y +CONFIG_PINCONF=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_STPMIC1=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_DM_REGULATOR_STPMIC1=y +CONFIG_DM_REGULATOR_SCMI=y +CONFIG_RESET_SCMI=y +CONFIG_DM_RNG=y +CONFIG_RNG_STM32=y +CONFIG_DM_RTC=y +CONFIG_RTC_STM32=y +CONFIG_SERIAL_RX_BUFFER=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_STM32_QSPI=y +CONFIG_STM32_SPI=y +CONFIG_SYSRESET_PSCI=y +CONFIG_TEE=y +CONFIG_OPTEE=y +# CONFIG_OPTEE_TA_AVB is not set +CONFIG_USB=y +CONFIG_DM_USB_GADGET=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC2=y +CONFIG_USB_ONBOARD_HUB=y +CONFIG_USB_HUB_DEBOUNCE_TIMEOUT=2000 +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="dh" +CONFIG_USB_GADGET_VENDOR_NUM=0x0483 +CONFIG_USB_GADGET_PRODUCT_NUM=0x5720 +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_WDT=y +CONFIG_WDT_STM32MP=y +CONFIG_FAT_WRITE=y +CONFIG_ERRNO_STR=y +# CONFIG_EFI_LOADER is not set