From: Padmarao Begari Date: Fri, 15 Jan 2021 02:50:40 +0000 (+0530) Subject: riscv: Add Microchip MPFS Icicle Kit support X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=64413e1b7caf080e4b6bfb58447219c201de48cb;p=u-boot.git riscv: Add Microchip MPFS Icicle Kit support This patch adds Microchip MPFS Icicle Kit support. For now, only NS16550 Serial, Microchip clock, Cadence eMMC and MACB drivers are enabled. The Microchip MPFS Icicle defconfig by default builds U-Boot for S-Mode because U-Boot on Microchip PolarFire SoC will run in S-Mode as payload of HSS + OpenSBI. Signed-off-by: Padmarao Begari Reviewed-by: Anup Patel Reviewed-by: Bin Meng Tested-by: Bin Meng --- diff --git a/board/microchip/mpfs_icicle/Kconfig b/board/microchip/mpfs_icicle/Kconfig index bf8e1a13ec..4678462378 100644 --- a/board/microchip/mpfs_icicle/Kconfig +++ b/board/microchip/mpfs_icicle/Kconfig @@ -20,7 +20,30 @@ config BOARD_SPECIFIC_OPTIONS # dummy def_bool y select GENERIC_RISCV select BOARD_EARLY_INIT_F + select BOARD_LATE_INIT imply SMP + imply CLK_CCF + imply CLK_MPFS imply SYS_NS16550 + imply CMD_DHCP + imply CMD_EXT2 + imply CMD_EXT4 + imply CMD_FAT + imply CMD_FS_GENERIC + imply CMD_NET + imply CMD_PING + imply CMD_MMC + imply DOS_PARTITION + imply EFI_PARTITION + imply IP_DYN + imply ISO_PARTITION + imply MACB + imply MII + imply PHY_LIB + imply PHY_VITESSE + imply MMC + imply MMC_WRITE + imply MMC_SDHCI + imply MMC_SDHCI_CADENCE endif diff --git a/board/microchip/mpfs_icicle/mpfs_icicle.c b/board/microchip/mpfs_icicle/mpfs_icicle.c index 8381361ec3..0e34409067 100644 --- a/board/microchip/mpfs_icicle/mpfs_icicle.c +++ b/board/microchip/mpfs_icicle/mpfs_icicle.c @@ -6,10 +6,49 @@ #include #include +#include #include #include -#define MPFS_SYSREG_SOFT_RESET ((unsigned int *)0x20002088) +DECLARE_GLOBAL_DATA_PTR; + +#define MPFS_SYSREG_SOFT_RESET ((unsigned int *)0x20002088) +#define MPFS_SYS_SERVICE_CR ((unsigned int *)0x37020050) +#define MPFS_SYS_SERVICE_SR ((unsigned int *)0x37020054) +#define MPFS_SYS_SERVICE_MAILBOX ((unsigned char *)0x37020800) + +#define PERIPH_RESET_VALUE 0x1e8u +#define SERVICE_CR_REQ 0x1u +#define SERVICE_SR_BUSY 0x2u + +static void read_device_serial_number(u8 *response, u8 response_size) +{ + u8 idx; + u8 *response_buf; + unsigned int val; + + response_buf = (u8 *)response; + + writel(SERVICE_CR_REQ, MPFS_SYS_SERVICE_CR); + /* + * REQ bit will remain set till the system controller starts + * processing. + */ + do { + val = readl(MPFS_SYS_SERVICE_CR); + } while (SERVICE_CR_REQ == (val & SERVICE_CR_REQ)); + + /* + * Once system controller starts processing the busy bit will + * go high and service is completed when busy bit is gone low + */ + do { + val = readl(MPFS_SYS_SERVICE_SR); + } while (SERVICE_SR_BUSY == (val & SERVICE_SR_BUSY)); + + for (idx = 0; idx < response_size; idx++) + response_buf[idx] = readb(MPFS_SYS_SERVICE_MAILBOX + idx); +} int board_init(void) { @@ -22,10 +61,64 @@ int board_early_init_f(void) { unsigned int val; - /* Reset uart peripheral */ + /* Reset uart, mmc peripheral */ val = readl(MPFS_SYSREG_SOFT_RESET); - val = (val & ~(1u << 5u)); + val = (val & ~(PERIPH_RESET_VALUE)); writel(val, MPFS_SYSREG_SOFT_RESET); return 0; } + +int board_late_init(void) +{ + u32 ret; + u32 node; + u8 idx; + u8 device_serial_number[16] = { 0 }; + unsigned char mac_addr[6]; + char icicle_mac_addr[20]; + void *blob = (void *)gd->fdt_blob; + + node = fdt_path_offset(blob, "ethernet0"); + if (node < 0) { + printf("No ethernet0 path offset\n"); + return -ENODEV; + } + + ret = fdtdec_get_byte_array(blob, node, "local-mac-address", mac_addr, 6); + if (ret) { + printf("No local-mac-address property\n"); + return -EINVAL; + } + + read_device_serial_number(device_serial_number, 16); + + /* Update MAC address with device serial number */ + mac_addr[0] = 0x00; + mac_addr[1] = 0x04; + mac_addr[2] = 0xA3; + mac_addr[3] = device_serial_number[2]; + mac_addr[4] = device_serial_number[1]; + mac_addr[5] = device_serial_number[0]; + + ret = fdt_setprop(blob, node, "local-mac-address", mac_addr, 6); + if (ret) { + printf("Error setting local-mac-address property\n"); + return -ENODEV; + } + + icicle_mac_addr[0] = '['; + + sprintf(&icicle_mac_addr[1], "%pM", mac_addr); + + icicle_mac_addr[18] = ']'; + icicle_mac_addr[19] = '\0'; + + for (idx = 0; idx < 20; idx++) { + if (icicle_mac_addr[idx] == ':') + icicle_mac_addr[idx] = ' '; + } + env_set("icicle_mac_addr", icicle_mac_addr); + + return 0; +} diff --git a/configs/microchip_mpfs_icicle_defconfig b/configs/microchip_mpfs_icicle_defconfig index 2977966473..9abbc18a89 100644 --- a/configs/microchip_mpfs_icicle_defconfig +++ b/configs/microchip_mpfs_icicle_defconfig @@ -1,12 +1,15 @@ CONFIG_RISCV=y CONFIG_ENV_SIZE=0x2000 CONFIG_TARGET_MICROCHIP_ICICLE=y -CONFIG_NR_CPUS=5 CONFIG_ARCH_RV64I=y +CONFIG_RISCV_SMODE=y +CONFIG_SBI_V01=y +CONFIG_DEFAULT_DEVICE_TREE="microchip-mpfs-icicle-kit" +CONFIG_DISTRO_DEFAULTS=y +CONFIG_DISPLAY_CPUINFO=y +CONFIG_DISPLAY_BOARDINFO=y CONFIG_FIT=y -CONFIG_BOOTDELAY=3 CONFIG_SYS_PROMPT="RISC-V # " -CONFIG_OF_PRIOR_STAGE=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_BOOTP_SEND_HOSTNAME=y CONFIG_DM_MTD=y diff --git a/include/configs/microchip_mpfs_icicle.h b/include/configs/microchip_mpfs_icicle.h index 8a7470545b..24990370cf 100644 --- a/include/configs/microchip_mpfs_icicle.h +++ b/include/configs/microchip_mpfs_icicle.h @@ -7,53 +7,34 @@ #ifndef __CONFIG_H #define __CONFIG_H -/* - * CPU and Board Configuration Options - */ +#include -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_2M) -/* - * Print Buffer Size - */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_2M) -/* - * max number of command args - */ -#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_MALLOC_LEN SZ_8M -/* - * Boot Argument Buffer Size - */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * Size of malloc() pool - * 512kB is suggested, (CONFIG_ENV_SIZE + 128 * 1024) was not enough - */ -#define CONFIG_SYS_MALLOC_LEN (512 << 10) +#define CONFIG_SYS_BOOTM_LEN SZ_64M -/* - * Physical Memory Map - */ -#define PHYS_SDRAM_0 0x80000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_0_SIZE 0x40000000 /* 1 GB */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_0 +#define CONFIG_STANDALONE_LOAD_ADDR 0x80200000 -/* Init Stack Pointer */ -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x200000) +/* Environment options */ -#define CONFIG_SYS_LOAD_ADDR 0x80000000 /* SDRAM */ +#define BOOT_TARGET_DEVICES(func) \ + func(MMC, mmc, 0) \ + func(DHCP, dhcp, na) -/* - * memtest works on DRAM - */ +#include -/* When we use RAM as ENV */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "bootm_size=0x10000000\0" \ + "kernel_addr_r=0x84000000\0" \ + "fdt_addr_r=0x88000000\0" \ + "scriptaddr=0x88100000\0" \ + "pxefile_addr_r=0x88200000\0" \ + "ramdisk_addr_r=0x88300000\0" \ + BOOTENV #endif /* __CONFIG_H */