From: Ilya Yanok Date: Wed, 7 Jul 2010 16:16:13 +0000 (+0400) Subject: MPC8308RDB: minimal support for devboard from Freescale X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=5fb17030d5634d9951da48af69be08146eb71bf9;p=u-boot.git MPC8308RDB: minimal support for devboard from Freescale This patch provides support for MPC8308RDB development board from Freescale with a minimal set of features: Dual UART is supported NOR flash is supported Both TSEC Ethernet controllers are supported PCI Express initialization is supported The following features are enabled in configuration but not fully tested: I2C (used to get the board revision) I2C-connected RTC VSC7385 switch There is one (hopefully) minor issue: on soft reset the board sometimes resets twice. I've not managed to find the fix for this problem yet. As a workaround instruction cache can be disabled. Signed-off-by: Ilya Yanok Signed-off-by: Kim Phillips --- diff --git a/MAINTAINERS b/MAINTAINERS index 94850702ea..d9158cec5a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -490,6 +490,10 @@ Stephen Williams JSE PPC405GPr +Ilya Yanok + + MPC8308RDB MPC8308 + Roy Zang mpc7448hpc2 MPC7448 diff --git a/MAKEALL b/MAKEALL index 463739069d..e7651dc462 100755 --- a/MAKEALL +++ b/MAKEALL @@ -360,6 +360,7 @@ LIST_8260=" \ LIST_83xx=" \ caddy2 \ kmeter1 \ + MPC8308RDB \ MPC8313ERDB_33 \ MPC8313ERDB_NAND_66 \ MPC8315ERDB \ diff --git a/board/freescale/mpc8308rdb/Makefile b/board/freescale/mpc8308rdb/Makefile new file mode 100644 index 0000000000..e9bfa2bc0d --- /dev/null +++ b/board/freescale/mpc8308rdb/Makefile @@ -0,0 +1,52 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# (C) Copyright 2010 +# Ilya Yanok, Emcraft Systems, yanok@emcraft.com +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o sdram.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/mpc8308rdb/config.mk b/board/freescale/mpc8308rdb/config.mk new file mode 100644 index 0000000000..f76826495e --- /dev/null +++ b/board/freescale/mpc8308rdb/config.mk @@ -0,0 +1 @@ +TEXT_BASE = 0xFE000000 diff --git a/board/freescale/mpc8308rdb/mpc8308rdb.c b/board/freescale/mpc8308rdb/mpc8308rdb.c new file mode 100644 index 0000000000..a864189571 --- /dev/null +++ b/board/freescale/mpc8308rdb/mpc8308rdb.c @@ -0,0 +1,160 @@ +/* + * Copyright (C) 2010 Freescale Semiconductor, Inc. + * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + immap_t *im = (immap_t *)CONFIG_SYS_IMMR; + + if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF) + gd->flags |= GD_FLG_SILENT; + + return 0; +} + +static u8 read_board_info(void) +{ + u8 val8; + i2c_set_bus_num(0); + + if (i2c_read(CONFIG_SYS_I2C_PCF8574A_ADDR, 0, 0, &val8, 1) == 0) + return val8; + else + return 0; +} + +int checkboard(void) +{ + static const char * const rev_str[] = { + "1.0", + "", + "", + "", + "", + }; + u8 info; + int i; + + info = read_board_info(); + i = (!info) ? 4 : info & 0x03; + + printf("Board: Freescale MPC8308RDB Rev %s\n", rev_str[i]); + + return 0; +} + +static struct pci_region pcie_regions_0[] = { + { + .bus_start = CONFIG_SYS_PCIE1_MEM_BASE, + .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS, + .size = CONFIG_SYS_PCIE1_MEM_SIZE, + .flags = PCI_REGION_MEM, + }, + { + .bus_start = CONFIG_SYS_PCIE1_IO_BASE, + .phys_start = CONFIG_SYS_PCIE1_IO_PHYS, + .size = CONFIG_SYS_PCIE1_IO_SIZE, + .flags = PCI_REGION_IO, + }, +}; + +void pci_init_board(void) +{ + immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; + sysconf83xx_t *sysconf = &immr->sysconf; + clk83xx_t *clk = (clk83xx_t *)&immr->clk; + law83xx_t *pcie_law = sysconf->pcielaw; + struct pci_region *pcie_reg[] = { pcie_regions_0 }; + + fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX, + FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V); + + clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM , + SCCR_PCIEXP1CM_1); + + /* Deassert the resets in the control register */ + out_be32(&sysconf->pecr1, 0xE0008000); + udelay(2000); + + /* Configure PCI Express Local Access Windows */ + out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR); + out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB); + + mpc83xx_pcie_init(1, pcie_reg, 0); +} +/* + * Miscellaneous late-boot configurations + * + * If a VSC7385 microcode image is present, then upload it. +*/ +int misc_init_r(void) +{ +#ifdef CONFIG_VSC7385_IMAGE + if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE, + CONFIG_VSC7385_IMAGE_SIZE)) { + puts("Failure uploading VSC7385 microcode.\n"); + return 1; + } +#endif + + return 0; +} +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); + fdt_fixup_dr_usb(blob, bd); +} +#endif + +int board_eth_init(bd_t *bis) +{ + int rv, num_if = 0; + + /* Initialize TSECs first */ + if ((rv = cpu_eth_init(bis)) >= 0) + num_if += rv; + else + printf("ERROR: failed to initialize TSECs.\n"); + + if ((rv = pci_eth_init(bis)) >= 0) + num_if += rv; + else + printf("ERROR: failed to initialize PCI Ethernet.\n"); + + return num_if; +} diff --git a/board/freescale/mpc8308rdb/sdram.c b/board/freescale/mpc8308rdb/sdram.c new file mode 100644 index 0000000000..939c1b85b8 --- /dev/null +++ b/board/freescale/mpc8308rdb/sdram.c @@ -0,0 +1,126 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com + * + * Authors: Nick.Spence@freescale.com + * Wilson.Lo@freescale.com + * scottwood@freescale.com + * + * This files is mostly identical to the original from + * board\freescale\mpc8315erdb\sdram.c + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +#include +#include + +#include + +DECLARE_GLOBAL_DATA_PTR; + +static void resume_from_sleep(void) +{ + u32 magic = *(u32 *)0; + + typedef void (*func_t)(void); + func_t resume = *(func_t *)4; + + if (magic == 0xf5153ae5) + resume(); + + gd->flags &= ~GD_FLG_SILENT; + puts("\nResume from sleep failed: bad magic word\n"); +} + +/* Fixed sdram init -- doesn't use serial presence detect. + * + * This is useful for faster booting in configs where the RAM is unlikely + * to be changed, or for things like NAND booting where space is tight. + */ +static long fixed_sdram(void) +{ + immap_t *im = (immap_t *)CONFIG_SYS_IMMR; + u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024; + u32 msize_log2 = __ilog2(msize); + + out_be32(&im->sysconf.ddrlaw[0].bar, + CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000); + out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1)); + out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE); + + /* + * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg], + * or the DDR2 controller may fail to initialize correctly. + */ + udelay(50000); + + out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24); + out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG); + + /* Currently we use only one CS, so disable the other bank. */ + out_be32(&im->ddr.cs_config[1], 0); + + out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL); + out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3); + out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1); + out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2); + out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0); + + if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF) { + out_be32(&im->ddr.sdram_cfg, + CONFIG_SYS_DDR_SDRAM_CFG | SDRAM_CFG_BI); + } else { + out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG); + } + + out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2); + out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE); + out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2); + + out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL); + sync(); + + /* enable DDR controller */ + setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN); + sync(); + + return get_ram_size(CONFIG_SYS_DDR_SDRAM_BASE, msize); +} + +phys_size_t initdram(int board_type) +{ + immap_t *im = (immap_t *)CONFIG_SYS_IMMR; + u32 msize; + + if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im) + return -1; + + /* DDR SDRAM */ + msize = fixed_sdram(); + + if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF) + resume_from_sleep(); + + /* return total bus SDRAM size(bytes) -- DDR */ + return msize; +} diff --git a/boards.cfg b/boards.cfg index da31c3647e..c23696f139 100644 --- a/boards.cfg +++ b/boards.cfg @@ -331,6 +331,7 @@ ppmc8260 powerpc mpc8260 RPXsuper powerpc mpc8260 rpxsuper rsdproto powerpc mpc8260 MPC8266ADS powerpc mpc8260 mpc8266ads freescale +MPC8308RDB powerpc mpc83xx mpc8308rdb freescale MPC8323ERDB powerpc mpc83xx mpc8323erdb freescale MPC8349EMDS powerpc mpc83xx mpc8349emds freescale MPC837XERDB powerpc mpc83xx mpc837xerdb freescale diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h new file mode 100644 index 0000000000..6cd5da7950 --- /dev/null +++ b/include/configs/MPC8308RDB.h @@ -0,0 +1,560 @@ +/* + * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. + * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com + * + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_MPC83xx 1 /* MPC83xx family */ +#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ +#define CONFIG_MPC8308RDB 1 /* MPC8308RDB board specific */ + +#define CONFIG_MISC_INIT_R + +/* + * On-board devices + * + * TSEC1 is SoC TSEC + * TSEC2 is VSC switch + */ +#define CONFIG_TSEC1 +#define CONFIG_VSC7385_ENET + +/* + * System Clock Setup + */ +#define CONFIG_83XX_CLKIN 33333333 /* in Hz */ +#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN + +/* + * Hardware Reset Configuration Word + * if CLKIN is 66.66MHz, then + * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz + * We choose the A type silicon as default, so the core is 400Mhz. + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_SVCOD_DIV_2 |\ + HRCWL_CSB_TO_CLKIN_4X1 |\ + HRCWL_CORE_TO_CSB_3X1) +/* + * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits + * in 8308's HRCWH according to the manual, but original Freescale's + * code has them and I've expirienced some problems using the board + * with BDI3000 attached when I've tried to set these bits to zero + * (UART doesn't work after the 'reset run' command). + */ +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_RGMII |\ + HRCWH_TSEC2M_IN_RGMII |\ + HRCWH_BIG_ENDIAN) + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRH 0x01b7d103 +#define CONFIG_SYS_SICRL 0x00000040 /* 3.3V, no delay */ + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ + +/* + * IMMR new address + */ +#define CONFIG_SYS_IMMR 0xE0000000 + +/* + * SERDES + */ +#define CONFIG_FSL_SERDES +#define CONFIG_FSL_SERDES1 0xe3000 + +/* + * Arbiter Setup + */ +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ +#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ + +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ + | DDRCDR_PZ_LOZ \ + | DDRCDR_NZ_LOZ \ + | DDRCDR_ODT \ + | DDRCDR_Q_DRN) + /* 0x7b880001 */ +/* + * Manually set up DDR parameters + * consist of two chips HY5PS12621BFP-C4 from HYNIX + */ + +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ + +#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ + | 0x00010000 /* ODT_WR to CSn */ \ + | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) + /* 0x80010102 */ +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ + | (0 << TIMING_CFG0_WRT_SHIFT) \ + | (0 << TIMING_CFG0_RRT_SHIFT) \ + | (0 << TIMING_CFG0_WWT_SHIFT) \ + | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ + | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) + /* 0x00220802 */ +#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ + | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ + | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ + | (5 << TIMING_CFG1_CASLAT_SHIFT) \ + | (6 << TIMING_CFG1_REFREC_SHIFT) \ + | (2 << TIMING_CFG1_WRREC_SHIFT) \ + | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ + | (2 << TIMING_CFG1_WRTORD_SHIFT)) + /* 0x27256222 */ +#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ + | (4 << TIMING_CFG2_CPO_SHIFT) \ + | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ + | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ + | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ + | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ + | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) + /* 0x121048c5 */ +#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ + | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + /* 0x03600100 */ +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_32_BE) + /* 0x43080000 */ + +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ +#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ + | (0x0232 << SDRAM_MODE_SD_SHIFT)) + /* ODT 150ohm CL=3, AL=1 on SDRAM */ +#define CONFIG_SYS_DDR_MODE2 0x00000000 + +/* + * Memory test + */ +#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x07f00000 + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 +#define CONFIG_SYS_LBC_LBCR 0x00040000 + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ + +/* Window base at flash base */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */ + +#define CONFIG_SYS_BR0_PRELIM (\ + CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\ + (2 << BR_PS_SHIFT) /* 16 bit port size */ |\ + BR_V) /* valid */ +#define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV2 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX \ + | OR_GPCM_EHTR \ + | OR_GPCM_EAD) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +/* 127 64KB sectors and 8 8KB top sectors per device */ +#define CONFIG_SYS_MAX_FLASH_SECT 135 + +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +/* + * NAND Flash on the Local Bus + */ +#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */ +#define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_NAND_BASE \ + | (2< " + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_FSL_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0x51}} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + + +/* + * Board info - revision and where boot from + */ +#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39 + +/* + * Config on-board RTC + */ +#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCIE1_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 +#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 + +/* + * Fake PCIE2 definitions: there is no PCIE2 on this board but the code + * in arch/powerpc/cpu/mpc83xx/pcie.c doesn't compile without this + */ +#define CONFIG_SYS_PCIE2_BASE 0xC0000000 +#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000 +#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000 +#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 + +#define CONFIG_PCI +#define CONFIG_PCIE + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 + +/* + * TSEC + */ +#define CONFIG_NET_MULTI +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) + +/* + * TSEC ethernet configuration + */ +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1_NAME "eTSEC0" +#define CONFIG_TSEC2_NAME "eTSEC1" +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT + +/* Options are: eTSEC[0-1] */ +#define CONFIG_ETHPRIME "eTSEC0" + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ + HID0_ENABLE_INSTRUCTION_CACHE | \ + HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) +#define CONFIG_SYS_HID2 HID2_HBE + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U + +/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ + BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ + BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | \ + BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ + BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Environment Configuration + */ + +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ + +#define xstr(s) str(s) +#define str(s) #s + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs}" \ + " console=${consoledev},${baudrate}\0" \ + "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "addmisc=setenv bootargs ${bootargs}\0" \ + "kernel_addr=FE080000\0" \ + "fdt_addr=FE280000\0" \ + "ramdisk_addr=FE290000\0" \ + "u-boot=mpc8308rdb/u-boot.bin\0" \ + "kernel_addr_r=1000000\0" \ + "fdt_addr_r=C00000\0" \ + "hostname=mpc8308rdb\0" \ + "bootfile=mpc8308rdb/uImage\0" \ + "fdtfile=mpc8308rdb/mpc8308rdb.dtb\0" \ + "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ + "flash_self=run ramargs addip addtty addmtd addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ + "tftp ${fdt_addr_r} ${fdtfile};" \ + "run nfsargs addip addtty addmtd addmisc;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "bootcmd=run flash_self\0" \ + "load=tftp ${loadaddr} ${u-boot}\0" \ + "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \ + " +${filesize};cp.b ${fileaddr} " \ + xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ + "upd=run load update\0" \ + +#endif /* __CONFIG_H */