From: Jagan Teki Date: Sat, 13 Jun 2020 07:55:35 +0000 (+0530) Subject: powerpc: Remove T4160QDS_NAND_defconfig board X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=5d226cd0136c72f725a4c38747c187878243b620;p=u-boot.git powerpc: Remove T4160QDS_NAND_defconfig board DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Patch-cc: Ruchika Gupta Signed-off-by: Jagan Teki Reviewed-by: Priyanka Jain --- diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig index 5979e356fb..9801055e54 100644 --- a/arch/powerpc/cpu/mpc85xx/Kconfig +++ b/arch/powerpc/cpu/mpc85xx/Kconfig @@ -296,15 +296,6 @@ config TARGET_T2081QDS select FSL_DDR_FIRST_SLOT_QUAD_CAPABLE select FSL_DDR_INTERACTIVE -config TARGET_T4160QDS - bool "Support T4160QDS" - select ARCH_T4160 - select BOARD_LATE_INIT if CHAIN_OF_TRUST - select SUPPORT_SPL - select PHYS_64BIT - imply CMD_SATA - imply PANIC_HANG - config TARGET_T4160RDB bool "Support T4160RDB" select ARCH_T4160 @@ -312,16 +303,6 @@ config TARGET_T4160RDB select PHYS_64BIT imply PANIC_HANG -config TARGET_T4240QDS - bool "Support T4240QDS" - select ARCH_T4240 - select BOARD_LATE_INIT if CHAIN_OF_TRUST - select SUPPORT_SPL - select PHYS_64BIT - select FSL_DDR_FIRST_SLOT_QUAD_CAPABLE - imply CMD_SATA - imply PANIC_HANG - config TARGET_T4240RDB bool "Support T4240RDB" select ARCH_T4240 @@ -1538,7 +1519,6 @@ source "board/freescale/t102xrdb/Kconfig" source "board/freescale/t104xrdb/Kconfig" source "board/freescale/t208xqds/Kconfig" source "board/freescale/t208xrdb/Kconfig" -source "board/freescale/t4qds/Kconfig" source "board/freescale/t4rdb/Kconfig" source "board/gdsys/p1022/Kconfig" source "board/keymile/Kconfig" diff --git a/board/freescale/t4qds/Kconfig b/board/freescale/t4qds/Kconfig deleted file mode 100644 index f7c1a0c15d..0000000000 --- a/board/freescale/t4qds/Kconfig +++ /dev/null @@ -1,14 +0,0 @@ -if TARGET_T4160QDS || TARGET_T4240QDS - -config SYS_BOARD - default "t4qds" - -config SYS_VENDOR - default "freescale" - -config SYS_CONFIG_NAME - default "T4240QDS" - -source "board/freescale/common/Kconfig" - -endif diff --git a/board/freescale/t4qds/MAINTAINERS b/board/freescale/t4qds/MAINTAINERS deleted file mode 100644 index 44bb2f5c6d..0000000000 --- a/board/freescale/t4qds/MAINTAINERS +++ /dev/null @@ -1,18 +0,0 @@ -T4QDS BOARD -#M: Shaohui Xie -S: Orphan (since 2018-05) -F: board/freescale/t4qds/ -F: include/configs/T4240QDS.h -F: configs/T4160QDS_defconfig -F: configs/T4160QDS_NAND_defconfig -F: configs/T4160QDS_SDCARD_defconfig -F: configs/T4240QDS_defconfig -F: configs/T4240QDS_NAND_defconfig -F: configs/T4240QDS_SDCARD_defconfig -F: configs/T4240QDS_SRIO_PCIE_BOOT_defconfig - -T4160QDS_SECURE_BOOT BOARD -M: Ruchika Gupta -S: Maintained -F: configs/T4160QDS_SECURE_BOOT_defconfig -F: configs/T4240QDS_SECURE_BOOT_defconfig diff --git a/board/freescale/t4qds/Makefile b/board/freescale/t4qds/Makefile deleted file mode 100644 index 11144222d3..0000000000 --- a/board/freescale/t4qds/Makefile +++ /dev/null @@ -1,15 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# Copyright 2012 Freescale Semiconductor, Inc. - -ifdef CONFIG_SPL_BUILD -obj-y += spl.o -else -obj-$(CONFIG_TARGET_T4160QDS) += t4240qds.o eth.o -obj-$(CONFIG_TARGET_T4240QDS) += t4240qds.o eth.o -obj-$(CONFIG_PCI) += pci.o -endif - -obj-y += ddr.o -obj-y += law.o -obj-y += tlb.o diff --git a/board/freescale/t4qds/README b/board/freescale/t4qds/README deleted file mode 100644 index bf238146db..0000000000 --- a/board/freescale/t4qds/README +++ /dev/null @@ -1,194 +0,0 @@ -Overview --------- -The T4240QDS is a high-performance computing evaluation, development and test -platform supporting the T4240 QorIQ™ Power Architecture™ processor. T4240QDS is -optimized to support the high-bandwidth DDR3 memory ports, as well as the -highly-configurable SerDes ports. The system is lead-free and RoHS-compliant. - -Board Features - SERDES Connections - 32 lanes grouped into four 8-lane banks - Two “front side” banks dedicated to Ethernet - - High-speed crosspoint switch fabric on selected lanes - - Two PCI Express slots with side-band connector supporting - - SGMII - - XAUI - - HiGig - - I-pass connectors allow board-to-board and loopback support - Two “back side” banks dedicated to other protocols - - High-speed crosspoint switch fabric on all lanes - - Four PCI Express slots with side-band connector supporting - - PCI Express 3.0 - - SATA 2.0 - - SRIO 2.0 - - Supports 4X Aurora debug with two connectors - DDR Controllers - Three independant 64-bit DDR3 controllers - Supports rates of 1866 up to 2133 MHz data-rate - Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller - DDR power supplies 1.5V to all devices with automatic tracking of VTT. - Power software-switchable to 1.35V if software detects all DDR3LP devices. - MT9JSF25672AZ-2G1KZESZF has been tested at 1333, 1600, 1867, 2000 and - 2133MT/s speeds. For 1867MT/s and above, read-to-write turnaround time - increases by 1 clock. - - IFC/Local Bus - NAND flash: 8-bit, async or sync, up to 2GB. - NOR: 16-bit, Address/Data Multiplexed (ADM), up to 128 MB - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB - - NOR devices support 16 virtual banks - GASIC: Minimal target within Qixis FPGA - PromJET rapid memory download support - Address demultiplexing handled within FPGA. - - Flexible demux allows 8 or 16 bit evaluation. - IFC Debug/Development card - - Support for 32-bit devices - Ethernet - Support two on-board RGMII 10/100/1G ethernet ports. - SGMII and XAUI support via SERDES block (see above). - 1588 support via Symmetricom board. - QIXIS System Logic FPGA - Manages system power and reset sequencing - Manages DUT, board, clock, etc. configuration for dynamic shmoo - Collects V-I-T data in background for code/power profiling. - Supports legacy TMT test features (POSt, IRS, SYSCLK-synchronous assertion) - General fault monitoring and logging - Runs from ATX “hot” power rails allowing operation while system is off. - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - - Switch selectable to one of 16 common settings in the interval 33MHz-166MHz. - - Software selectable in 1MHz increments from 1-200MHz. - SERDES clocks - - Provides clocks to all SerDes blocks and slots - - 100, 125 and 156.25 MHz - Power Supplies - Dedicated regulators for VDD - - Adjustable from (0.7V to 1.3V at 80A - - Regulators can be controlled by VID and/or software - Dedicated regulator for GVDD_PL: 1.35/1.5V at 22A - - VTT/MVREF automatically track operating voltage - Dedicated regulators/filters for AVDD supplies - Dedicated regulators for other supplies: OVDD, BVDD, DVDD, LVDD, POVDD, etc. - USB - Supports two USB 2.0 ports with integrated PHYs - - One type A, one type micro-AB with 1.0A power per port. - Other IO - eSDHC/MMC - - SDHC card slot - eSPI port - - High-speed serial flash - Two Serial port - Four I2C ports - XFI - XFI is supported on T4QDS-XFI board which removed slot3 and routed - four Lanes A/B/C/D to a SFP+ cages, which to house fiber cable or - direct attach cable(copper), the copper cable is used to emulate - 10GBASE-KR scenario. - So, for XFI usage, there are two scenarios, one will use fiber cable, - another will use copper cable. An hwconfig env "fsl_10gkr_copper" is - introduced to indicate a XFI port will use copper cable, and U-Boot - will fixup the dtb accordingly. - It's used as: fsl_10gkr_copper:<10g_mac_name> - The <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2, they - do not have to be coexist in hwconfig. If a MAC is listed in the env - "fsl_10gkr_copper", it will use copper cable, otherwise, fiber cable - will be used by default. - for ex. set "fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm2_10g1,fm2_10g2" in - hwconfig, then both four XFI ports will use copper cable. - set "fsl_10gkr_copper:fm1_10g1,fm1_10g2" in hwconfig, then first two - XFI ports will use copper cable, the other two XFI ports will use fiber - cable. - -Memory map ----------- -The addresses in brackets are physical addresses. - -0x0_0000_0000 (0x0_0000_0000) - 0x0_7fff_ffff 2GB DDR (more than 2GB is initialized but not mapped under with TLB) -0x0_8000_0000 (0xc_0000_0000) - 0x0_dfff_ffff 1.5GB PCIE memory -0x0_f000_0000 (0xf_0000_0000) - 0x0_f1ff_ffff 32MB DCSR (includes trace buffers) -0x0_f400_0000 (0xf_f400_0000) - 0x0_f5ff_ffff 32MB BMan -0x0_f600_0000 (0xf_f600_0000) - 0x0_f7ff_ffff 32MB QMan -0x0_f800_0000 (0xf_f800_0000) - 0x0_f803_ffff 256KB PCIE IO -0x0_e000_0000 (0xf_e000_0000) - 0x0_efff_ffff 256MB NOR flash -0x0_fe00_0000 (0xf_fe00_0000) - 0x0_feff_ffff 16MB CCSR -0x0_ffdf_0000 (0xf_ffdf_0000) - 0x0_ffdf_03ff 4KB QIXIS -0x0_ffff_f000 (0x0_7fff_fff0) - 0x0_ffff_ffff 4KB Boot page translation for secondary cores - -The physical address of the last (boot page translation) varies with the actual DDR size. - -Voltage ID and VDD override --------------------- -T4240 has a VID feature. U-Boot reads the VID efuses and adjust the voltage -accordingly. The voltage can also be override by command vdd_override. The -syntax is - -vdd_override , eg. 1050 is for 1.050v. - -Upon success, the actual voltage will be read back. The value is checked -for safety and any invalid value will not adjust the voltage. - -Another way to override VDD is to use environmental variable, in case of using -command is too late for some debugging. The syntax is - -setenv t4240qds_vdd_mv -saveenv -reset - -The override voltage takes effect when booting. - -Note: voltage adjustment needs to be done step by step. Changing voltage too -rapidly may cause current surge. The voltage stepping is done by software. -Users can set the final voltage directly. - -2-stage NAND/SD boot loader -------------------------------- -PBL initializes the internal SRAM and copy SPL(160K) in SRAM. -SPL further initialise DDR using SPD and environment variables -and copy U-Boot(768 KB) from NAND/SD device to DDR. -Finally SPL transers control to U-Boot for futher booting. - -SPL has following features: - - Executes within 256K - - No relocation required - -Run time view of SPL framework -------------------------------------------------- -|Area | Address | -------------------------------------------------- -|SecureBoot header | 0xFFFC0000 (32KB) | -------------------------------------------------- -|GD, BD | 0xFFFC8000 (4KB) | -------------------------------------------------- -|ENV | 0xFFFC9000 (8KB) | -------------------------------------------------- -|HEAP | 0xFFFCB000 (50KB) | -------------------------------------------------- -|STACK | 0xFFFD8000 (22KB) | -------------------------------------------------- -|U-Boot SPL | 0xFFFD8000 (160KB) | -------------------------------------------------- - -NAND Flash memory Map on T4QDS --------------------------------------------------------------- -Start End Definition Size -0x000000 0x0FFFFF U-Boot img 1MB -0x140000 0x15FFFF U-Boot env 128KB -0x160000 0x17FFFF FMAN Ucode 128KB - -Micro SD Card memory Map on T4QDS ----------------------------------------------------- -Block #blocks Definition Size -0x008 2048 U-Boot img 1MB -0x800 0016 U-Boot env 8KB -0x820 0128 FMAN ucode 64KB - -Switch Settings: (ON is 1, OFF is 0) -=============== -NAND boot SW setting: -SW1[1:8] = 10000010 -SW2[1.1] = 0 -SW6[1:4] = 1001 - -SD boot SW setting: -SW1[1:8] = 00100000 -SW2[1.1] = 0 diff --git a/board/freescale/t4qds/ddr.c b/board/freescale/t4qds/ddr.c deleted file mode 100644 index 4fdd69d424..0000000000 --- a/board/freescale/t4qds/ddr.c +++ /dev/null @@ -1,134 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright 2012 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "ddr.h" - -DECLARE_GLOBAL_DATA_PTR; - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; - ulong ddr_freq; - - if (ctrl_num > 2) { - printf("Not supported controller number %d\n", ctrl_num); - return; - } - if (!pdimm->n_ranks) - return; - - /* - * we use identical timing for all slots. If needed, change the code - * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num]; - */ - if (popts->registered_dimm_en) - pbsp = rdimms[0]; - else - pbsp = udimms[0]; - - - /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr - * freqency and n_banks specified in board_specific_parameters table. - */ - ddr_freq = get_ddr_freq(0) / 1000000; - while (pbsp->datarate_mhz_high) { - if (pbsp->n_ranks == pdimm->n_ranks && - (pdimm->rank_density >> 30) >= pbsp->rank_gb) { - if (ddr_freq <= pbsp->datarate_mhz_high) { - popts->cpo_override = pbsp->cpo; - popts->write_data_delay = - pbsp->write_data_delay; - popts->clk_adjust = pbsp->clk_adjust; - popts->wrlvl_start = pbsp->wrlvl_start; - popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; - popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - popts->twot_en = pbsp->force_2t; - goto found; - } - pbsp_highest = pbsp; - } - pbsp++; - } - - if (pbsp_highest) { - printf("Error: board specific timing not found " - "for data rate %lu MT/s\n" - "Trying to use the highest speed (%u) parameters\n", - ddr_freq, pbsp_highest->datarate_mhz_high); - popts->cpo_override = pbsp_highest->cpo; - popts->write_data_delay = pbsp_highest->write_data_delay; - popts->clk_adjust = pbsp_highest->clk_adjust; - popts->wrlvl_start = pbsp_highest->wrlvl_start; - popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; - popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - popts->twot_en = pbsp_highest->force_2t; - } else { - panic("DIMM is not supported by this board"); - } -found: - debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n" - "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, " - "wrlvl_ctrl_3 0x%x\n", - pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb, - pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2, - pbsp->wrlvl_ctl_3); - - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 0; - /* - * Write leveling override - */ - popts->wrlvl_override = 1; - popts->wrlvl_sample = 0xf; - - /* - * Rtt and Rtt_WR override - */ - popts->rtt_override = 0; - - /* Enable ZQ calibration */ - popts->zq_en = 1; - - /* DHC_EN =1, ODT = 75 Ohm */ - popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); - popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); - - /* optimize cpo for erratum A-009942 */ - popts->cpo_sample = 0x63; -} - -int dram_init(void) -{ - phys_size_t dram_size; - - puts("Initializing....using SPD\n"); - -#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) - dram_size = fsl_ddr_sdram(); -#else - /* DDR has been initialised by first stage boot loader */ - dram_size = fsl_ddr_sdram_size(); -#endif - dram_size = setup_ddr_tlbs(dram_size / 0x100000); - dram_size *= 0x100000; - - gd->ram_size = dram_size; - - return 0; -} diff --git a/board/freescale/t4qds/ddr.h b/board/freescale/t4qds/ddr.h deleted file mode 100644 index a28d4314da..0000000000 --- a/board/freescale/t4qds/ddr.h +++ /dev/null @@ -1,81 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2013 Freescale Semiconductor, Inc. - */ - -#ifndef __DDR_H__ -#define __DDR_H__ -struct board_specific_parameters { - u32 n_ranks; - u32 datarate_mhz_high; - u32 rank_gb; - u32 clk_adjust; - u32 wrlvl_start; - u32 wrlvl_ctl_2; - u32 wrlvl_ctl_3; - u32 cpo; - u32 write_data_delay; - u32 force_2t; -}; - -/* - * These tables contain all valid speeds we want to override with board - * specific parameters. datarate_mhz_high values need to be in ascending order - * for each n_ranks group. - */ - -static const struct board_specific_parameters udimm0[] = { - /* - * memory controller 0 - * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T - * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay | - */ - {2, 1350, 4, 8, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, - {2, 1350, 0, 10, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0}, - {2, 1666, 4, 8, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0}, - {2, 1666, 0, 10, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0}, - {2, 1900, 0, 8, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0}, - {2, 2140, 0, 8, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0}, - {1, 1350, 0, 10, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, - {1, 1700, 0, 10, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0}, - {1, 1900, 0, 8, 8, 0x080a0a0c, 0x0e0e0f0a, 0xff, 2, 0}, - {1, 2140, 0, 8, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0}, - {} -}; - -static const struct board_specific_parameters rdimm0[] = { - /* - * memory controller 0 - * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T - * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay | - */ - {4, 1350, 0, 10, 9, 0x08070605, 0x06070806, 0xff, 2, 0}, - {4, 1666, 0, 10, 11, 0x0a080706, 0x07090906, 0xff, 2, 0}, - {4, 2140, 0, 10, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0}, - {2, 1350, 0, 10, 9, 0x08070605, 0x06070806, 0xff, 2, 0}, - {2, 1666, 0, 10, 11, 0x0a090806, 0x08090a06, 0xff, 2, 0}, - {2, 2140, 0, 10, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0}, - {1, 1350, 0, 10, 9, 0x08070605, 0x06070806, 0xff, 2, 0}, - {1, 1666, 0, 10, 11, 0x0a090806, 0x08090a06, 0xff, 2, 0}, - {1, 2140, 0, 8, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0}, - {} -}; - -/* - * The three slots have slightly different timing. The center values are good - * for all slots. We use identical speed tables for them. In future use, if - * DIMMs require separated tables, make more entries as needed. - */ -static const struct board_specific_parameters *udimms[] = { - udimm0, -}; - -/* - * The three slots have slightly different timing. See comments above. - */ -static const struct board_specific_parameters *rdimms[] = { - rdimm0, -}; - - -#endif diff --git a/board/freescale/t4qds/eth.c b/board/freescale/t4qds/eth.c deleted file mode 100644 index 810868ff39..0000000000 --- a/board/freescale/t4qds/eth.c +++ /dev/null @@ -1,869 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "../common/qixis.h" -#include "../common/fman.h" -#include - -#include "t4240qds_qixis.h" - -#define EMI_NONE 0xFFFFFFFF -#define EMI1_RGMII 0 -#define EMI1_SLOT1 1 -#define EMI1_SLOT2 2 -#define EMI1_SLOT3 3 -#define EMI1_SLOT4 4 -#define EMI1_SLOT5 5 -#define EMI1_SLOT7 7 -#define EMI2 8 -/* Slot6 and Slot8 do not have EMI connections */ - -static int mdio_mux[NUM_FM_PORTS]; - -static const char *mdio_names[] = { - "T4240QDS_MDIO0", - "T4240QDS_MDIO1", - "T4240QDS_MDIO2", - "T4240QDS_MDIO3", - "T4240QDS_MDIO4", - "T4240QDS_MDIO5", - "NULL", - "T4240QDS_MDIO7", - "T4240QDS_10GC", -}; - -static u8 lane_to_slot_fsm1[] = {1, 1, 1, 1, 2, 2, 2, 2}; -static u8 lane_to_slot_fsm2[] = {3, 3, 3, 3, 4, 4, 4, 4}; -static u8 slot_qsgmii_phyaddr[5][4] = { - {0, 0, 0, 0},/* not used, to make index match slot No. */ - {0, 1, 2, 3}, - {4, 5, 6, 7}, - {8, 9, 0xa, 0xb}, - {0xc, 0xd, 0xe, 0xf}, -}; -static u8 qsgmiiphy_fix[NUM_FM_PORTS] = {0}; - -static const char *t4240qds_mdio_name_for_muxval(u8 muxval) -{ - return mdio_names[muxval]; -} - -struct mii_dev *mii_dev_for_muxval(u8 muxval) -{ - struct mii_dev *bus; - const char *name = t4240qds_mdio_name_for_muxval(muxval); - - if (!name) { - printf("No bus for muxval %x\n", muxval); - return NULL; - } - - bus = miiphy_get_dev_by_name(name); - - if (!bus) { - printf("No bus by name %s\n", name); - return NULL; - } - - return bus; -} - -struct t4240qds_mdio { - u8 muxval; - struct mii_dev *realbus; -}; - -static void t4240qds_mux_mdio(u8 muxval) -{ - u8 brdcfg4; - if ((muxval < 6) || (muxval == 7)) { - brdcfg4 = QIXIS_READ(brdcfg[4]); - brdcfg4 &= ~BRDCFG4_EMISEL_MASK; - brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT); - QIXIS_WRITE(brdcfg[4], brdcfg4); - } -} - -static int t4240qds_mdio_read(struct mii_dev *bus, int addr, int devad, - int regnum) -{ - struct t4240qds_mdio *priv = bus->priv; - - t4240qds_mux_mdio(priv->muxval); - - return priv->realbus->read(priv->realbus, addr, devad, regnum); -} - -static int t4240qds_mdio_write(struct mii_dev *bus, int addr, int devad, - int regnum, u16 value) -{ - struct t4240qds_mdio *priv = bus->priv; - - t4240qds_mux_mdio(priv->muxval); - - return priv->realbus->write(priv->realbus, addr, devad, regnum, value); -} - -static int t4240qds_mdio_reset(struct mii_dev *bus) -{ - struct t4240qds_mdio *priv = bus->priv; - - return priv->realbus->reset(priv->realbus); -} - -static int t4240qds_mdio_init(char *realbusname, u8 muxval) -{ - struct t4240qds_mdio *pmdio; - struct mii_dev *bus = mdio_alloc(); - - if (!bus) { - printf("Failed to allocate T4240QDS MDIO bus\n"); - return -1; - } - - pmdio = malloc(sizeof(*pmdio)); - if (!pmdio) { - printf("Failed to allocate T4240QDS private data\n"); - free(bus); - return -1; - } - - bus->read = t4240qds_mdio_read; - bus->write = t4240qds_mdio_write; - bus->reset = t4240qds_mdio_reset; - strcpy(bus->name, t4240qds_mdio_name_for_muxval(muxval)); - - pmdio->realbus = miiphy_get_dev_by_name(realbusname); - - if (!pmdio->realbus) { - printf("No bus with name %s\n", realbusname); - free(bus); - free(pmdio); - return -1; - } - - pmdio->muxval = muxval; - bus->priv = pmdio; - - return mdio_register(bus); -} - -void board_ft_fman_fixup_port(void *blob, char * prop, phys_addr_t pa, - enum fm_port port, int offset) -{ - int interface = fm_info_get_enet_if(port); - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 prtcl2 = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS2_PRTCL; - - prtcl2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; - - if (interface == PHY_INTERFACE_MODE_SGMII || - interface == PHY_INTERFACE_MODE_QSGMII) { - switch (port) { - case FM1_DTSEC1: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy21"); - break; - case FM1_DTSEC2: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy22"); - break; - case FM1_DTSEC3: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy23"); - break; - case FM1_DTSEC4: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy24"); - break; - case FM1_DTSEC6: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy12"); - break; - case FM1_DTSEC9: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy14"); - else - fdt_set_phy_handle(blob, prop, pa, - "phy_sgmii4"); - break; - case FM1_DTSEC10: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy13"); - else - fdt_set_phy_handle(blob, prop, pa, - "phy_sgmii3"); - break; - case FM2_DTSEC1: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy41"); - break; - case FM2_DTSEC2: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy42"); - break; - case FM2_DTSEC3: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy43"); - break; - case FM2_DTSEC4: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy44"); - break; - case FM2_DTSEC6: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy32"); - break; - case FM2_DTSEC9: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy34"); - else - fdt_set_phy_handle(blob, prop, pa, - "phy_sgmii12"); - break; - case FM2_DTSEC10: - if (qsgmiiphy_fix[port]) - fdt_set_phy_handle(blob, prop, pa, - "sgmii_phy33"); - else - fdt_set_phy_handle(blob, prop, pa, - "phy_sgmii11"); - break; - default: - break; - } - } else if (interface == PHY_INTERFACE_MODE_XGMII && - ((prtcl2 == 55) || (prtcl2 == 57))) { - /* - * if the 10G is XFI, check hwconfig to see what is the - * media type, there are two types, fiber or copper, - * fix the dtb accordingly. - */ - int media_type = 0; - struct fixed_link f_link; - char lane_mode[20] = {"10GBASE-KR"}; - char buf[32] = "serdes-2,"; - int off; - - switch (port) { - case FM1_10GEC1: - if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g1")) { - media_type = 1; - fdt_set_phy_handle(blob, prop, pa, - "phy_xfi1"); - sprintf(buf, "%s%s%s", buf, "lane-a,", - (char *)lane_mode); - } - break; - case FM1_10GEC2: - if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g2")) { - media_type = 1; - fdt_set_phy_handle(blob, prop, pa, - "phy_xfi2"); - sprintf(buf, "%s%s%s", buf, "lane-b,", - (char *)lane_mode); - } - break; - case FM2_10GEC1: - if (hwconfig_sub("fsl_10gkr_copper", "fm2_10g1")) { - media_type = 1; - fdt_set_phy_handle(blob, prop, pa, - "phy_xfi3"); - sprintf(buf, "%s%s%s", buf, "lane-d,", - (char *)lane_mode); - } - break; - case FM2_10GEC2: - if (hwconfig_sub("fsl_10gkr_copper", "fm2_10g2")) { - media_type = 1; - fdt_set_phy_handle(blob, prop, pa, - "phy_xfi4"); - sprintf(buf, "%s%s%s", buf, "lane-c,", - (char *)lane_mode); - } - break; - default: - return; - } - - if (!media_type) { - /* fixed-link is used for XFI fiber cable */ - fdt_delprop(blob, offset, "phy-handle"); - f_link.phy_id = port; - f_link.duplex = 1; - f_link.link_speed = 10000; - f_link.pause = 0; - f_link.asym_pause = 0; - fdt_setprop(blob, offset, "fixed-link", &f_link, - sizeof(f_link)); - } else { - /* set property for copper cable */ - off = fdt_node_offset_by_compat_reg(blob, - "fsl,fman-memac-mdio", pa + 0x1000); - fdt_setprop_string(blob, off, "lane-instance", buf); - } - } -} - -void fdt_fixup_board_enet(void *fdt) -{ - int i; - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 prtcl2 = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS2_PRTCL; - - prtcl2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; - for (i = FM1_DTSEC1; i < NUM_FM_PORTS; i++) { - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_SGMII: - case PHY_INTERFACE_MODE_QSGMII: - switch (mdio_mux[i]) { - case EMI1_SLOT1: - fdt_status_okay_by_alias(fdt, "emi1_slot1"); - break; - case EMI1_SLOT2: - fdt_status_okay_by_alias(fdt, "emi1_slot2"); - break; - case EMI1_SLOT3: - fdt_status_okay_by_alias(fdt, "emi1_slot3"); - break; - case EMI1_SLOT4: - fdt_status_okay_by_alias(fdt, "emi1_slot4"); - break; - default: - break; - } - break; - case PHY_INTERFACE_MODE_XGMII: - /* check if it's XFI interface for 10g */ - if ((prtcl2 == 55) || (prtcl2 == 57)) { - if (i == FM1_10GEC1 && hwconfig_sub( - "fsl_10gkr_copper", "fm1_10g1")) - fdt_status_okay_by_alias( - fdt, "xfi_pcs_mdio1"); - if (i == FM1_10GEC2 && hwconfig_sub( - "fsl_10gkr_copper", "fm1_10g2")) - fdt_status_okay_by_alias( - fdt, "xfi_pcs_mdio2"); - if (i == FM2_10GEC1 && hwconfig_sub( - "fsl_10gkr_copper", "fm2_10g1")) - fdt_status_okay_by_alias( - fdt, "xfi_pcs_mdio3"); - if (i == FM2_10GEC2 && hwconfig_sub( - "fsl_10gkr_copper", "fm2_10g2")) - fdt_status_okay_by_alias( - fdt, "xfi_pcs_mdio4"); - break; - } - switch (i) { - case FM1_10GEC1: - fdt_status_okay_by_alias(fdt, "emi2_xauislot1"); - break; - case FM1_10GEC2: - fdt_status_okay_by_alias(fdt, "emi2_xauislot2"); - break; - case FM2_10GEC1: - fdt_status_okay_by_alias(fdt, "emi2_xauislot3"); - break; - case FM2_10GEC2: - fdt_status_okay_by_alias(fdt, "emi2_xauislot4"); - break; - default: - break; - } - break; - default: - break; - } - } -} - -static void initialize_qsgmiiphy_fix(void) -{ - int i; - unsigned short reg; - - for (i = 1; i <= 4; i++) { - /* - * Try to read if a SGMII card is used, we do it slot by slot. - * if a SGMII PHY address is valid on a slot, then we mark - * all ports on the slot, then fix the PHY address for the - * marked port when doing dtb fixup. - */ - if (miiphy_read(mdio_names[i], - SGMII_CARD_PORT1_PHY_ADDR, MII_PHYSID2, ®) != 0) { - debug("Slot%d PHY ID register 2 read failed\n", i); - continue; - } - - debug("Slot%d MII_PHYSID2 @ 0x1c= 0x%04x\n", i, reg); - - if (reg == 0xFFFF) { - /* No physical device present at this address */ - continue; - } - - switch (i) { - case 1: - qsgmiiphy_fix[FM1_DTSEC5] = 1; - qsgmiiphy_fix[FM1_DTSEC6] = 1; - qsgmiiphy_fix[FM1_DTSEC9] = 1; - qsgmiiphy_fix[FM1_DTSEC10] = 1; - slot_qsgmii_phyaddr[1][0] = SGMII_CARD_PORT1_PHY_ADDR; - slot_qsgmii_phyaddr[1][1] = SGMII_CARD_PORT2_PHY_ADDR; - slot_qsgmii_phyaddr[1][2] = SGMII_CARD_PORT3_PHY_ADDR; - slot_qsgmii_phyaddr[1][3] = SGMII_CARD_PORT4_PHY_ADDR; - break; - case 2: - qsgmiiphy_fix[FM1_DTSEC1] = 1; - qsgmiiphy_fix[FM1_DTSEC2] = 1; - qsgmiiphy_fix[FM1_DTSEC3] = 1; - qsgmiiphy_fix[FM1_DTSEC4] = 1; - slot_qsgmii_phyaddr[2][0] = SGMII_CARD_PORT1_PHY_ADDR; - slot_qsgmii_phyaddr[2][1] = SGMII_CARD_PORT2_PHY_ADDR; - slot_qsgmii_phyaddr[2][2] = SGMII_CARD_PORT3_PHY_ADDR; - slot_qsgmii_phyaddr[2][3] = SGMII_CARD_PORT4_PHY_ADDR; - break; - case 3: - qsgmiiphy_fix[FM2_DTSEC5] = 1; - qsgmiiphy_fix[FM2_DTSEC6] = 1; - qsgmiiphy_fix[FM2_DTSEC9] = 1; - qsgmiiphy_fix[FM2_DTSEC10] = 1; - slot_qsgmii_phyaddr[3][0] = SGMII_CARD_PORT1_PHY_ADDR; - slot_qsgmii_phyaddr[3][1] = SGMII_CARD_PORT2_PHY_ADDR; - slot_qsgmii_phyaddr[3][2] = SGMII_CARD_PORT3_PHY_ADDR; - slot_qsgmii_phyaddr[3][3] = SGMII_CARD_PORT4_PHY_ADDR; - break; - case 4: - qsgmiiphy_fix[FM2_DTSEC1] = 1; - qsgmiiphy_fix[FM2_DTSEC2] = 1; - qsgmiiphy_fix[FM2_DTSEC3] = 1; - qsgmiiphy_fix[FM2_DTSEC4] = 1; - slot_qsgmii_phyaddr[4][0] = SGMII_CARD_PORT1_PHY_ADDR; - slot_qsgmii_phyaddr[4][1] = SGMII_CARD_PORT2_PHY_ADDR; - slot_qsgmii_phyaddr[4][2] = SGMII_CARD_PORT3_PHY_ADDR; - slot_qsgmii_phyaddr[4][3] = SGMII_CARD_PORT4_PHY_ADDR; - break; - default: - break; - } - } -} - -int board_eth_init(bd_t *bis) -{ -#if defined(CONFIG_FMAN_ENET) - int i, idx, lane, slot, interface; - struct memac_mdio_info dtsec_mdio_info; - struct memac_mdio_info tgec_mdio_info; - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 srds_prtcl_s1, srds_prtcl_s2; - - srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS1_PRTCL; - srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; - srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS2_PRTCL; - srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; - - /* Initialize the mdio_mux array so we can recognize empty elements */ - for (i = 0; i < NUM_FM_PORTS; i++) - mdio_mux[i] = EMI_NONE; - - dtsec_mdio_info.regs = - (struct memac_mdio_controller *)CONFIG_SYS_FM2_DTSEC_MDIO_ADDR; - - dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; - - /* Register the 1G MDIO bus */ - fm_memac_mdio_init(bis, &dtsec_mdio_info); - - tgec_mdio_info.regs = - (struct memac_mdio_controller *)CONFIG_SYS_FM2_TGEC_MDIO_ADDR; - tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; - - /* Register the 10G MDIO bus */ - fm_memac_mdio_init(bis, &tgec_mdio_info); - - /* Register the muxing front-ends to the MDIO buses */ - t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII); - t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1); - t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2); - t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3); - t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4); - t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5); - t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT7); - t4240qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2); - - initialize_qsgmiiphy_fix(); - - switch (srds_prtcl_s1) { - case 1: - case 2: - case 4: - /* XAUI/HiGig in Slot1 and Slot2 */ - fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR); - fm_info_set_phy_address(FM1_10GEC2, FM1_10GEC2_PHY_ADDR); - break; - case 27: - case 28: - case 35: - case 36: - /* SGMII in Slot1 and Slot2 */ - fm_info_set_phy_address(FM1_DTSEC1, slot_qsgmii_phyaddr[2][0]); - fm_info_set_phy_address(FM1_DTSEC2, slot_qsgmii_phyaddr[2][1]); - fm_info_set_phy_address(FM1_DTSEC3, slot_qsgmii_phyaddr[2][2]); - fm_info_set_phy_address(FM1_DTSEC4, slot_qsgmii_phyaddr[2][3]); - fm_info_set_phy_address(FM1_DTSEC5, slot_qsgmii_phyaddr[1][0]); - fm_info_set_phy_address(FM1_DTSEC6, slot_qsgmii_phyaddr[1][1]); - if ((srds_prtcl_s2 != 55) && (srds_prtcl_s2 != 57)) { - fm_info_set_phy_address(FM1_DTSEC9, - slot_qsgmii_phyaddr[1][3]); - fm_info_set_phy_address(FM1_DTSEC10, - slot_qsgmii_phyaddr[1][2]); - } - break; - case 37: - case 38: - fm_info_set_phy_address(FM1_DTSEC1, slot_qsgmii_phyaddr[2][0]); - fm_info_set_phy_address(FM1_DTSEC2, slot_qsgmii_phyaddr[2][1]); - fm_info_set_phy_address(FM1_DTSEC3, slot_qsgmii_phyaddr[2][2]); - fm_info_set_phy_address(FM1_DTSEC4, slot_qsgmii_phyaddr[2][3]); - fm_info_set_phy_address(FM1_DTSEC5, slot_qsgmii_phyaddr[1][0]); - fm_info_set_phy_address(FM1_DTSEC6, slot_qsgmii_phyaddr[1][1]); - if ((srds_prtcl_s2 != 55) && (srds_prtcl_s2 != 57)) { - fm_info_set_phy_address(FM1_DTSEC9, - slot_qsgmii_phyaddr[1][2]); - fm_info_set_phy_address(FM1_DTSEC10, - slot_qsgmii_phyaddr[1][3]); - } - break; - case 39: - case 40: - case 45: - case 46: - case 47: - case 48: - fm_info_set_phy_address(FM1_DTSEC5, slot_qsgmii_phyaddr[1][0]); - fm_info_set_phy_address(FM1_DTSEC6, slot_qsgmii_phyaddr[1][1]); - if ((srds_prtcl_s2 != 55) && (srds_prtcl_s2 != 57)) { - fm_info_set_phy_address(FM1_DTSEC10, - slot_qsgmii_phyaddr[1][2]); - fm_info_set_phy_address(FM1_DTSEC9, - slot_qsgmii_phyaddr[1][3]); - } - fm_info_set_phy_address(FM1_DTSEC1, slot_qsgmii_phyaddr[2][0]); - fm_info_set_phy_address(FM1_DTSEC2, slot_qsgmii_phyaddr[2][1]); - fm_info_set_phy_address(FM1_DTSEC3, slot_qsgmii_phyaddr[2][2]); - fm_info_set_phy_address(FM1_DTSEC4, slot_qsgmii_phyaddr[2][3]); - break; - default: - puts("Invalid SerDes1 protocol for T4240QDS\n"); - break; - } - - for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { - idx = i - FM1_DTSEC1; - interface = fm_info_get_enet_if(i); - switch (interface) { - case PHY_INTERFACE_MODE_SGMII: - case PHY_INTERFACE_MODE_QSGMII: - if (interface == PHY_INTERFACE_MODE_QSGMII) { - if (idx <= 3) - lane = serdes_get_first_lane(FSL_SRDS_1, - QSGMII_FM1_A); - else - lane = serdes_get_first_lane(FSL_SRDS_1, - QSGMII_FM1_B); - if (lane < 0) - break; - slot = lane_to_slot_fsm1[lane]; - debug("FM1@DTSEC%u expects QSGMII in slot %u\n", - idx + 1, slot); - } else { - lane = serdes_get_first_lane(FSL_SRDS_1, - SGMII_FM1_DTSEC1 + idx); - if (lane < 0) - break; - slot = lane_to_slot_fsm1[lane]; - debug("FM1@DTSEC%u expects SGMII in slot %u\n", - idx + 1, slot); - } - if (QIXIS_READ(present2) & (1 << (slot - 1))) - fm_disable_port(i); - switch (slot) { - case 1: - mdio_mux[i] = EMI1_SLOT1; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - case 2: - mdio_mux[i] = EMI1_SLOT2; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - }; - break; - case PHY_INTERFACE_MODE_RGMII: - /* FM1 DTSEC5 routes to RGMII with EC2 */ - debug("FM1@DTSEC%u is RGMII at address %u\n", - idx + 1, 2); - if (i == FM1_DTSEC5) - fm_info_set_phy_address(i, 2); - mdio_mux[i] = EMI1_RGMII; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - default: - break; - } - } - - for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { - idx = i - FM1_10GEC1; - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_XGMII: - if ((srds_prtcl_s2 == 55) || (srds_prtcl_s2 == 57)) { - /* A fake PHY address to make U-Boot happy */ - fm_info_set_phy_address(i, i); - } else { - lane = serdes_get_first_lane(FSL_SRDS_1, - XAUI_FM1_MAC9 + idx); - if (lane < 0) - break; - slot = lane_to_slot_fsm1[lane]; - if (QIXIS_READ(present2) & (1 << (slot - 1))) - fm_disable_port(i); - } - mdio_mux[i] = EMI2; - fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); - break; - default: - break; - } - } - -#if (CONFIG_SYS_NUM_FMAN == 2) - switch (srds_prtcl_s2) { - case 1: - case 2: - case 4: - /* XAUI/HiGig in Slot3 and Slot4 */ - fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC1_PHY_ADDR); - fm_info_set_phy_address(FM2_10GEC2, FM2_10GEC2_PHY_ADDR); - break; - case 6: - case 7: - case 12: - case 13: - case 14: - case 15: - case 16: - case 21: - case 22: - case 23: - case 24: - case 25: - case 26: - /* XAUI/HiGig in Slot3, SGMII in Slot4 */ - fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC1_PHY_ADDR); - fm_info_set_phy_address(FM2_DTSEC1, slot_qsgmii_phyaddr[4][0]); - fm_info_set_phy_address(FM2_DTSEC2, slot_qsgmii_phyaddr[4][1]); - fm_info_set_phy_address(FM2_DTSEC3, slot_qsgmii_phyaddr[4][2]); - fm_info_set_phy_address(FM2_DTSEC4, slot_qsgmii_phyaddr[4][3]); - break; - case 27: - case 28: - case 35: - case 36: - /* SGMII in Slot3 and Slot4 */ - fm_info_set_phy_address(FM2_DTSEC1, slot_qsgmii_phyaddr[4][0]); - fm_info_set_phy_address(FM2_DTSEC2, slot_qsgmii_phyaddr[4][1]); - fm_info_set_phy_address(FM2_DTSEC3, slot_qsgmii_phyaddr[4][2]); - fm_info_set_phy_address(FM2_DTSEC4, slot_qsgmii_phyaddr[4][3]); - fm_info_set_phy_address(FM2_DTSEC5, slot_qsgmii_phyaddr[3][0]); - fm_info_set_phy_address(FM2_DTSEC6, slot_qsgmii_phyaddr[3][1]); - fm_info_set_phy_address(FM2_DTSEC9, slot_qsgmii_phyaddr[3][3]); - fm_info_set_phy_address(FM2_DTSEC10, slot_qsgmii_phyaddr[3][2]); - break; - case 37: - case 38: - /* QSGMII in Slot3 and Slot4 */ - fm_info_set_phy_address(FM2_DTSEC1, slot_qsgmii_phyaddr[4][0]); - fm_info_set_phy_address(FM2_DTSEC2, slot_qsgmii_phyaddr[4][1]); - fm_info_set_phy_address(FM2_DTSEC3, slot_qsgmii_phyaddr[4][2]); - fm_info_set_phy_address(FM2_DTSEC4, slot_qsgmii_phyaddr[4][3]); - fm_info_set_phy_address(FM2_DTSEC5, slot_qsgmii_phyaddr[3][0]); - fm_info_set_phy_address(FM2_DTSEC6, slot_qsgmii_phyaddr[3][1]); - fm_info_set_phy_address(FM2_DTSEC9, slot_qsgmii_phyaddr[3][2]); - fm_info_set_phy_address(FM2_DTSEC10, slot_qsgmii_phyaddr[3][3]); - break; - case 39: - case 40: - case 45: - case 46: - case 47: - case 48: - /* SGMII in Slot3 */ - fm_info_set_phy_address(FM2_DTSEC5, slot_qsgmii_phyaddr[3][0]); - fm_info_set_phy_address(FM2_DTSEC6, slot_qsgmii_phyaddr[3][1]); - fm_info_set_phy_address(FM2_DTSEC9, slot_qsgmii_phyaddr[3][3]); - fm_info_set_phy_address(FM2_DTSEC10, slot_qsgmii_phyaddr[3][2]); - /* QSGMII in Slot4 */ - fm_info_set_phy_address(FM2_DTSEC1, slot_qsgmii_phyaddr[4][0]); - fm_info_set_phy_address(FM2_DTSEC2, slot_qsgmii_phyaddr[4][1]); - fm_info_set_phy_address(FM2_DTSEC3, slot_qsgmii_phyaddr[4][2]); - fm_info_set_phy_address(FM2_DTSEC4, slot_qsgmii_phyaddr[4][3]); - break; - case 49: - case 50: - case 51: - case 52: - case 53: - case 54: - fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC1_PHY_ADDR); - fm_info_set_phy_address(FM2_DTSEC1, slot_qsgmii_phyaddr[4][0]); - fm_info_set_phy_address(FM2_DTSEC2, slot_qsgmii_phyaddr[4][1]); - fm_info_set_phy_address(FM2_DTSEC3, slot_qsgmii_phyaddr[4][2]); - fm_info_set_phy_address(FM2_DTSEC4, slot_qsgmii_phyaddr[4][3]); - break; - case 55: - case 57: - /* XFI in Slot3, SGMII in Slot4 */ - fm_info_set_phy_address(FM2_DTSEC1, slot_qsgmii_phyaddr[4][0]); - fm_info_set_phy_address(FM2_DTSEC2, slot_qsgmii_phyaddr[4][1]); - fm_info_set_phy_address(FM2_DTSEC3, slot_qsgmii_phyaddr[4][2]); - fm_info_set_phy_address(FM2_DTSEC4, slot_qsgmii_phyaddr[4][3]); - break; - default: - puts("Invalid SerDes2 protocol for T4240QDS\n"); - break; - } - - for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) { - idx = i - FM2_DTSEC1; - interface = fm_info_get_enet_if(i); - switch (interface) { - case PHY_INTERFACE_MODE_SGMII: - case PHY_INTERFACE_MODE_QSGMII: - if (interface == PHY_INTERFACE_MODE_QSGMII) { - if (idx <= 3) - lane = serdes_get_first_lane(FSL_SRDS_2, - QSGMII_FM2_A); - else - lane = serdes_get_first_lane(FSL_SRDS_2, - QSGMII_FM2_B); - if (lane < 0) - break; - slot = lane_to_slot_fsm2[lane]; - debug("FM2@DTSEC%u expects QSGMII in slot %u\n", - idx + 1, slot); - } else { - lane = serdes_get_first_lane(FSL_SRDS_2, - SGMII_FM2_DTSEC1 + idx); - if (lane < 0) - break; - slot = lane_to_slot_fsm2[lane]; - debug("FM2@DTSEC%u expects SGMII in slot %u\n", - idx + 1, slot); - } - if (QIXIS_READ(present2) & (1 << (slot - 1))) - fm_disable_port(i); - switch (slot) { - case 3: - mdio_mux[i] = EMI1_SLOT3; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - case 4: - mdio_mux[i] = EMI1_SLOT4; - fm_info_set_mdio(i, - mii_dev_for_muxval(mdio_mux[i])); - break; - }; - break; - case PHY_INTERFACE_MODE_RGMII: - /* - * If DTSEC5 is RGMII, then it's routed via via EC1 to - * the first on-board RGMII port. If DTSEC6 is RGMII, - * then it's routed via via EC2 to the second on-board - * RGMII port. - */ - debug("FM2@DTSEC%u is RGMII at address %u\n", - idx + 1, i == FM2_DTSEC5 ? 1 : 2); - fm_info_set_phy_address(i, i == FM2_DTSEC5 ? 1 : 2); - mdio_mux[i] = EMI1_RGMII; - fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); - break; - default: - break; - } - } - - for (i = FM2_10GEC1; i < FM2_10GEC1 + CONFIG_SYS_NUM_FM2_10GEC; i++) { - idx = i - FM2_10GEC1; - switch (fm_info_get_enet_if(i)) { - case PHY_INTERFACE_MODE_XGMII: - if ((srds_prtcl_s2 == 55) || (srds_prtcl_s2 == 57)) { - /* A fake PHY address to make U-Boot happy */ - fm_info_set_phy_address(i, i); - } else { - lane = serdes_get_first_lane(FSL_SRDS_2, - XAUI_FM2_MAC9 + idx); - if (lane < 0) - break; - slot = lane_to_slot_fsm2[lane]; - if (QIXIS_READ(present2) & (1 << (slot - 1))) - fm_disable_port(i); - } - mdio_mux[i] = EMI2; - fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); - break; - default: - break; - } - } -#endif /* CONFIG_SYS_NUM_FMAN */ - - cpu_eth_init(bis); -#endif /* CONFIG_FMAN_ENET */ - - return pci_eth_init(bis); -} diff --git a/board/freescale/t4qds/law.c b/board/freescale/t4qds/law.c deleted file mode 100644 index cb7bdf391b..0000000000 --- a/board/freescale/t4qds/law.c +++ /dev/null @@ -1,33 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2008-2012 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -#include -#include -#include - -struct law_entry law_table[] = { - SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), -#ifdef CONFIG_SYS_BMAN_MEM_PHYS - SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), -#endif -#ifdef CONFIG_SYS_QMAN_MEM_PHYS - SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), -#endif -#ifdef QIXIS_BASE_PHYS - SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), -#endif -#ifdef CONFIG_SYS_DCSRBAR_PHYS - /* Limit DCSR to 32M to access NPC Trace Buffer */ - SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR), -#endif -#ifdef CONFIG_SYS_NAND_BASE_PHYS - SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC), -#endif -}; - -int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t4qds/pci.c b/board/freescale/t4qds/pci.c deleted file mode 100644 index 26e2a0af4a..0000000000 --- a/board/freescale/t4qds/pci.c +++ /dev/null @@ -1,23 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2007-2012 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -void pci_init_board(void) -{ - fsl_pcie_init_board(0); -} - -void pci_of_setup(void *blob, bd_t *bd) -{ - FT_FSL_PCI_SETUP; -} diff --git a/board/freescale/t4qds/spl.c b/board/freescale/t4qds/spl.c deleted file mode 100644 index d72d207a76..0000000000 --- a/board/freescale/t4qds/spl.c +++ /dev/null @@ -1,145 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* Copyright 2014 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "../common/qixis.h" -#include "t4240qds_qixis.h" - -#define FSL_CORENET_CCSR_PORSR1_RCW_MASK 0xFF800000 - -DECLARE_GLOBAL_DATA_PTR; - -phys_size_t get_effective_memsize(void) -{ - return CONFIG_SYS_L3_SIZE; -} - -unsigned long get_board_sys_clk(void) -{ - u8 sysclk_conf = QIXIS_READ(brdcfg[1]); - - switch (sysclk_conf & 0x0F) { - case QIXIS_SYSCLK_83: - return 83333333; - case QIXIS_SYSCLK_100: - return 100000000; - case QIXIS_SYSCLK_125: - return 125000000; - case QIXIS_SYSCLK_133: - return 133333333; - case QIXIS_SYSCLK_150: - return 150000000; - case QIXIS_SYSCLK_160: - return 160000000; - case QIXIS_SYSCLK_166: - return 166666666; - } - return 66666666; -} - -unsigned long get_board_ddr_clk(void) -{ - u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); - - switch ((ddrclk_conf & 0x30) >> 4) { - case QIXIS_DDRCLK_100: - return 100000000; - case QIXIS_DDRCLK_125: - return 125000000; - case QIXIS_DDRCLK_133: - return 133333333; - } - return 66666666; -} - -void board_init_f(ulong bootflag) -{ - u32 plat_ratio, sys_clk, ccb_clk; - ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; -#ifdef CONFIG_SPL_NAND_BOOT - u32 porsr1, pinctl; -#endif - -#ifdef CONFIG_SPL_NAND_BOOT - porsr1 = in_be32(&gur->porsr1); - pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000); - out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl); -#endif - /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */ - memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t)); - - /* Update GD pointer */ - gd = (gd_t *)(CONFIG_SPL_GD_ADDR); - - /* compiler optimization barrier needed for GCC >= 3.4 */ - __asm__ __volatile__("" : : : "memory"); - - console_init_f(); - - /* initialize selected port with appropriate baud rate */ - sys_clk = get_board_sys_clk(); - plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f; - ccb_clk = sys_clk * plat_ratio / 2; - - NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, - ccb_clk / 16 / CONFIG_BAUDRATE); - -#ifdef CONFIG_SPL_MMC_BOOT - puts("\nSD boot...\n"); -#elif defined(CONFIG_SPL_NAND_BOOT) - puts("\nNAND boot...\n"); -#endif - relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0); -} - -void board_init_r(gd_t *gd, ulong dest_addr) -{ - bd_t *bd; - - bd = (bd_t *)(gd + sizeof(gd_t)); - memset(bd, 0, sizeof(bd_t)); - gd->bd = bd; - bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR; - bd->bi_memsize = CONFIG_SYS_L3_SIZE; - - arch_cpu_init(); - get_clocks(); - mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, - CONFIG_SPL_RELOC_MALLOC_SIZE); - gd->flags |= GD_FLG_FULL_MALLOC_INIT; - -#ifdef CONFIG_SPL_NAND_BOOT - nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, - (uchar *)SPL_ENV_ADDR); -#endif -#ifdef CONFIG_SPL_MMC_BOOT - mmc_initialize(bd); - mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, - (uchar *)SPL_ENV_ADDR); -#endif - - gd->env_addr = (ulong)(SPL_ENV_ADDR); - gd->env_valid = ENV_VALID; - - i2c_init_all(); - - dram_init(); - -#ifdef CONFIG_SPL_MMC_BOOT - mmc_boot(); -#elif defined(CONFIG_SPL_NAND_BOOT) - nand_boot(); -#endif -} diff --git a/board/freescale/t4qds/t4240emu.c b/board/freescale/t4qds/t4240emu.c deleted file mode 100644 index 8f2032acc7..0000000000 --- a/board/freescale/t4qds/t4240emu.c +++ /dev/null @@ -1,85 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2013 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -int checkboard(void) -{ - struct cpu_type *cpu = gd->arch.cpu; - - printf("Board: %sEMU\n", cpu->name); - - return 0; -} - -int board_early_init_r(void) -{ - const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; - int flash_esel = find_tlb_idx((void *)flashbase, 1); - - /* - * Remap Boot flash + PROMJET region to caching-inhibited - * so that flash can be erased properly. - */ - - /* Flush d-cache and invalidate i-cache of any FLASH data */ - flush_dcache(); - invalidate_icache(); - - if (flash_esel == -1) { - /* very unlikely unless something is messed up */ - puts("Error: Could not find TLB for FLASH BASE\n"); - flash_esel = 2; /* give our best effort to continue */ - } else { - /* invalidate existing TLB entry for flash */ - disable_tlb(flash_esel); - } - - set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, - MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, flash_esel, BOOKE_PAGESZ_256M, 1); - - return 0; -} - -int misc_init_r(void) -{ - return 0; -} - -int ft_board_setup(void *blob, bd_t *bd) -{ - phys_addr_t base; - phys_size_t size; - - ft_cpu_setup(blob, bd); - - base = env_get_bootm_low(); - size = env_get_bootm_size(); - - fdt_fixup_memory(blob, (u64)base, (u64)size); - - fdt_fixup_liodn(blob); - fsl_fdt_fixup_dr_usb(blob, bd); - - return 0; -} diff --git a/board/freescale/t4qds/t4240qds.c b/board/freescale/t4qds/t4240qds.c deleted file mode 100644 index 543a2cb6e2..0000000000 --- a/board/freescale/t4qds/t4240qds.c +++ /dev/null @@ -1,929 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2009-2012 Freescale Semiconductor, Inc. - * Copyright 2020 NXP - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include "../common/qixis.h" -#include "../common/vsc3316_3308.h" -#include "t4qds.h" -#include "t4240qds_qixis.h" - -DECLARE_GLOBAL_DATA_PTR; - -static int8_t vsc3316_fsm1_tx[8][2] = { {0, 0}, {1, 1}, {6, 6}, {7, 7}, - {8, 8}, {9, 9}, {14, 14}, {15, 15} }; - -static int8_t vsc3316_fsm2_tx[8][2] = { {2, 2}, {3, 3}, {4, 4}, {5, 5}, - {10, 10}, {11, 11}, {12, 12}, {13, 13} }; - -static int8_t vsc3316_fsm1_rx[8][2] = { {2, 12}, {3, 13}, {4, 5}, {5, 4}, - {10, 11}, {11, 10}, {12, 2}, {13, 3} }; - -static int8_t vsc3316_fsm2_rx[8][2] = { {0, 15}, {1, 14}, {6, 7}, {7, 6}, - {8, 9}, {9, 8}, {14, 1}, {15, 0} }; - -int checkboard(void) -{ - char buf[64]; - u8 sw; - struct cpu_type *cpu = gd->arch.cpu; - unsigned int i; - - printf("Board: %sQDS, ", cpu->name); - printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ", - QIXIS_READ(id), QIXIS_READ(arch)); - - sw = QIXIS_READ(brdcfg[0]); - sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; - - if (sw < 0x8) - printf("vBank: %d\n", sw); - else if (sw == 0x8) - puts("Promjet\n"); - else if (sw == 0x9) - puts("NAND\n"); - else - printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); - - printf("FPGA: v%d (%s), build %d", - (int)QIXIS_READ(scver), qixis_read_tag(buf), - (int)qixis_read_minor()); - /* the timestamp string contains "\n" at the end */ - printf(" on %s", qixis_read_time(buf)); - - /* - * Display the actual SERDES reference clocks as configured by the - * dip switches on the board. Note that the SWx registers could - * technically be set to force the reference clocks to match the - * values that the SERDES expects (or vice versa). For now, however, - * we just display both values and hope the user notices when they - * don't match. - */ - puts("SERDES Reference Clocks: "); - sw = QIXIS_READ(brdcfg[2]); - for (i = 0; i < MAX_SERDES; i++) { - static const char * const freq[] = { - "100", "125", "156.25", "161.1328125"}; - unsigned int clock = (sw >> (6 - 2 * i)) & 3; - - printf("SERDES%u=%sMHz ", i+1, freq[clock]); - } - puts("\n"); - - return 0; -} - -int select_i2c_ch_pca9547(u8 ch, int bus_num) -{ - int ret; - -#ifdef CONFIG_DM_I2C - struct udevice *dev; - - ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI, - 1, &dev); - if (ret) { - printf("%s: Cannot find udev for a bus %d\n", __func__, - bus_num); - return ret; - } - - ret = dm_i2c_write(dev, 0, &ch, 1); -#else - ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); -#endif - if (ret) { - puts("PCA: failed to select proper channel\n"); - return ret; - } - - return 0; -} - -/* - * read_voltage from sensor on I2C bus - * We use average of 4 readings, waiting for 532us befor another reading - */ -#define NUM_READINGS 4 /* prefer to be power of 2 for efficiency */ -#define WAIT_FOR_ADC 532 /* wait for 532 microseconds for ADC */ - -static inline int read_voltage(void) -{ - int i, ret, voltage_read = 0; - u16 vol_mon; -#ifdef CONFIG_DM_I2C - struct udevice *dev; - int bus_num = 0; -#endif - - for (i = 0; i < NUM_READINGS; i++) { -#ifdef CONFIG_DM_I2C - ret = i2c_get_chip_for_busnum(bus_num, I2C_VOL_MONITOR_ADDR, - 1, &dev); - if (ret) { - printf("%s: Cannot find udev for a bus %d\n", __func__, - bus_num); - return ret; - } - - ret = dm_i2c_read(dev, - I2C_VOL_MONITOR_BUS_V_OFFSET, - (void *)&vol_mon, 2); -#else - ret = i2c_read(I2C_VOL_MONITOR_ADDR, - I2C_VOL_MONITOR_BUS_V_OFFSET, 1, (void *)&vol_mon, 2); -#endif - if (ret) { - printf("VID: failed to read core voltage\n"); - return ret; - } - if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) { - printf("VID: Core voltage sensor error\n"); - return -1; - } - debug("VID: bus voltage reads 0x%04x\n", vol_mon); - /* LSB = 4mv */ - voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4; - udelay(WAIT_FOR_ADC); - } - /* calculate the average */ - voltage_read /= NUM_READINGS; - - return voltage_read; -} - -/* - * We need to calculate how long before the voltage starts to drop or increase - * It returns with the loop count. Each loop takes several readings (532us) - */ -static inline int wait_for_voltage_change(int vdd_last) -{ - int timeout, vdd_current; - - vdd_current = read_voltage(); - /* wait until voltage starts to drop */ - for (timeout = 0; abs(vdd_last - vdd_current) <= 4 && - timeout < 100; timeout++) { - vdd_current = read_voltage(); - } - if (timeout >= 100) { - printf("VID: Voltage adjustment timeout\n"); - return -1; - } - return timeout; -} - -/* - * argument 'wait' is the time we know the voltage difference can be measured - * this function keeps reading the voltage until it is stable - */ -static inline int wait_for_voltage_stable(int wait) -{ - int timeout, vdd_current, vdd_last; - - vdd_last = read_voltage(); - udelay(wait * NUM_READINGS * WAIT_FOR_ADC); - /* wait until voltage is stable */ - vdd_current = read_voltage(); - for (timeout = 0; abs(vdd_last - vdd_current) >= 4 && - timeout < 100; timeout++) { - vdd_last = vdd_current; - udelay(wait * NUM_READINGS * WAIT_FOR_ADC); - vdd_current = read_voltage(); - } - if (timeout >= 100) { - printf("VID: Voltage adjustment timeout\n"); - return -1; - } - - return vdd_current; -} - -static inline int set_voltage(u8 vid) -{ - int wait, vdd_last; - - vdd_last = read_voltage(); - QIXIS_WRITE(brdcfg[6], vid); - wait = wait_for_voltage_change(vdd_last); - if (wait < 0) - return -1; - debug("VID: Waited %d us\n", wait * NUM_READINGS * WAIT_FOR_ADC); - wait = wait ? wait : 1; - - vdd_last = wait_for_voltage_stable(wait); - if (vdd_last < 0) - return -1; - debug("VID: Current voltage is %d mV\n", vdd_last); - - return vdd_last; -} - - -static int adjust_vdd(ulong vdd_override) -{ - int re_enable = disable_interrupts(); - ccsr_gur_t __iomem *gur = - (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 fusesr; - u8 vid, vid_current; - int vdd_target, vdd_current, vdd_last; - int ret; - unsigned long vdd_string_override; - char *vdd_string; - static const uint16_t vdd[32] = { - 0, /* unused */ - 9875, /* 0.9875V */ - 9750, - 9625, - 9500, - 9375, - 9250, - 9125, - 9000, - 8875, - 8750, - 8625, - 8500, - 8375, - 8250, - 8125, - 10000, /* 1.0000V */ - 10125, - 10250, - 10375, - 10500, - 10625, - 10750, - 10875, - 11000, - 0, /* reserved */ - }; - struct vdd_drive { - u8 vid; - unsigned voltage; - }; - - ret = select_i2c_ch_pca9547(I2C_MUX_CH_VOL_MONITOR, 0); - if (ret) { - debug("VID: I2c failed to switch channel\n"); - ret = -1; - goto exit; - } - - /* get the voltage ID from fuse status register */ - fusesr = in_be32(&gur->dcfg_fusesr); - vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) & - FSL_CORENET_DCFG_FUSESR_VID_MASK; - if (vid == FSL_CORENET_DCFG_FUSESR_VID_MASK) { - vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) & - FSL_CORENET_DCFG_FUSESR_ALTVID_MASK; - } - vdd_target = vdd[vid]; - - /* check override variable for overriding VDD */ - vdd_string = env_get("t4240qds_vdd_mv"); - if (vdd_override == 0 && vdd_string && - !strict_strtoul(vdd_string, 10, &vdd_string_override)) - vdd_override = vdd_string_override; - if (vdd_override >= 819 && vdd_override <= 1212) { - vdd_target = vdd_override * 10; /* convert to 1/10 mV */ - debug("VDD override is %lu\n", vdd_override); - } else if (vdd_override != 0) { - printf("Invalid value.\n"); - } - - if (vdd_target == 0) { - debug("VID: VID not used\n"); - ret = 0; - goto exit; - } else { - /* round up and divice by 10 to get a value in mV */ - vdd_target = DIV_ROUND_UP(vdd_target, 10); - debug("VID: vid = %d mV\n", vdd_target); - } - - /* - * Check current board VID setting - * Voltage regulator support output to 6.250mv step - * The highes voltage allowed for this board is (vid=0x40) 1.21250V - * the lowest is (vid=0x7f) 0.81875V - */ - vid_current = QIXIS_READ(brdcfg[6]); - vdd_current = 121250 - (vid_current - 0x40) * 625; - debug("VID: Current vid setting is (0x%x) %d mV\n", - vid_current, vdd_current/100); - - /* - * Read voltage monitor to check real voltage. - * Voltage monitor LSB is 4mv. - */ - vdd_last = read_voltage(); - if (vdd_last < 0) { - printf("VID: Could not read voltage sensor abort VID adjustment\n"); - ret = -1; - goto exit; - } - debug("VID: Core voltage is at %d mV\n", vdd_last); - /* - * Adjust voltage to at or 8mV above target. - * Each step of adjustment is 6.25mV. - * Stepping down too fast may cause over current. - */ - while (vdd_last > 0 && vid_current < 0x80 && - vdd_last > (vdd_target + 8)) { - vid_current++; - vdd_last = set_voltage(vid_current); - } - /* - * Check if we need to step up - * This happens when board voltage switch was set too low - */ - while (vdd_last > 0 && vid_current >= 0x40 && - vdd_last < vdd_target + 2) { - vid_current--; - vdd_last = set_voltage(vid_current); - } - if (vdd_last > 0) - printf("VID: Core voltage %d mV\n", vdd_last); - else - ret = -1; - -exit: - if (re_enable) - enable_interrupts(); - return ret; -} - -/* Configure Crossbar switches for Front-Side SerDes Ports */ -int config_frontside_crossbar_vsc3316(void) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 srds_prtcl_s1, srds_prtcl_s2; - int ret; - - ret = select_i2c_ch_pca9547(I2C_MUX_CH_VSC3316_FS, 0); - if (ret) - return ret; - - srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS1_PRTCL; - srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; - switch (srds_prtcl_s1) { - case 37: - case 38: - /* swap first lane and third lane on slot1 */ - vsc3316_fsm1_tx[0][1] = 14; - vsc3316_fsm1_tx[6][1] = 0; - vsc3316_fsm1_rx[1][1] = 2; - vsc3316_fsm1_rx[6][1] = 13; - case 39: - case 40: - case 45: - case 46: - case 47: - case 48: - /* swap first lane and third lane on slot2 */ - vsc3316_fsm1_tx[2][1] = 8; - vsc3316_fsm1_tx[4][1] = 6; - vsc3316_fsm1_rx[2][1] = 10; - vsc3316_fsm1_rx[5][1] = 5; - default: - ret = vsc3316_config(VSC3316_FSM_TX_ADDR, vsc3316_fsm1_tx, 8); - if (ret) - return ret; - ret = vsc3316_config(VSC3316_FSM_RX_ADDR, vsc3316_fsm1_rx, 8); - if (ret) - return ret; - break; - } - - srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS2_PRTCL; - srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; - switch (srds_prtcl_s2) { - case 37: - case 38: - /* swap first lane and third lane on slot3 */ - vsc3316_fsm2_tx[2][1] = 11; - vsc3316_fsm2_tx[5][1] = 4; - vsc3316_fsm2_rx[2][1] = 9; - vsc3316_fsm2_rx[4][1] = 7; - case 39: - case 40: - case 45: - case 46: - case 47: - case 48: - case 49: - case 50: - case 51: - case 52: - case 53: - case 54: - /* swap first lane and third lane on slot4 */ - vsc3316_fsm2_tx[6][1] = 3; - vsc3316_fsm2_tx[1][1] = 12; - vsc3316_fsm2_rx[0][1] = 1; - vsc3316_fsm2_rx[6][1] = 15; - default: - ret = vsc3316_config(VSC3316_FSM_TX_ADDR, vsc3316_fsm2_tx, 8); - if (ret) - return ret; - ret = vsc3316_config(VSC3316_FSM_RX_ADDR, vsc3316_fsm2_rx, 8); - if (ret) - return ret; - break; - } - - return 0; -} - -int config_backside_crossbar_mux(void) -{ - ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); - u32 srds_prtcl_s3, srds_prtcl_s4; - u8 brdcfg; - - srds_prtcl_s3 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS3_PRTCL; - srds_prtcl_s3 >>= FSL_CORENET2_RCWSR4_SRDS3_PRTCL_SHIFT; - switch (srds_prtcl_s3) { - case 0: - /* SerDes3 is not enabled */ - break; - case 1: - case 2: - case 9: - case 10: - /* SD3(0:7) => SLOT5(0:7) */ - brdcfg = QIXIS_READ(brdcfg[12]); - brdcfg &= ~BRDCFG12_SD3MX_MASK; - brdcfg |= BRDCFG12_SD3MX_SLOT5; - QIXIS_WRITE(brdcfg[12], brdcfg); - break; - case 3: - case 4: - case 5: - case 6: - case 7: - case 8: - case 11: - case 12: - case 13: - case 14: - case 15: - case 16: - case 17: - case 18: - case 19: - case 20: - /* SD3(4:7) => SLOT6(0:3) */ - brdcfg = QIXIS_READ(brdcfg[12]); - brdcfg &= ~BRDCFG12_SD3MX_MASK; - brdcfg |= BRDCFG12_SD3MX_SLOT6; - QIXIS_WRITE(brdcfg[12], brdcfg); - break; - default: - printf("WARNING: unsupported for SerDes3 Protocol %d\n", - srds_prtcl_s3); - return -1; - } - - srds_prtcl_s4 = in_be32(&gur->rcwsr[4]) & - FSL_CORENET2_RCWSR4_SRDS4_PRTCL; - srds_prtcl_s4 >>= FSL_CORENET2_RCWSR4_SRDS4_PRTCL_SHIFT; - switch (srds_prtcl_s4) { - case 0: - /* SerDes4 is not enabled */ - break; - case 1: - case 2: - /* 10b, SD4(0:7) => SLOT7(0:7) */ - brdcfg = QIXIS_READ(brdcfg[12]); - brdcfg &= ~BRDCFG12_SD4MX_MASK; - brdcfg |= BRDCFG12_SD4MX_SLOT7; - QIXIS_WRITE(brdcfg[12], brdcfg); - break; - case 3: - case 4: - case 5: - case 6: - case 7: - case 8: - /* x1b, SD4(4:7) => SLOT8(0:3) */ - brdcfg = QIXIS_READ(brdcfg[12]); - brdcfg &= ~BRDCFG12_SD4MX_MASK; - brdcfg |= BRDCFG12_SD4MX_SLOT8; - QIXIS_WRITE(brdcfg[12], brdcfg); - break; - case 9: - case 10: - case 11: - case 12: - case 13: - case 14: - case 15: - case 16: - case 18: - /* 00b, SD4(4:5) => AURORA, SD4(6:7) => SATA */ - brdcfg = QIXIS_READ(brdcfg[12]); - brdcfg &= ~BRDCFG12_SD4MX_MASK; - brdcfg |= BRDCFG12_SD4MX_AURO_SATA; - QIXIS_WRITE(brdcfg[12], brdcfg); - break; - default: - printf("WARNING: unsupported for SerDes4 Protocol %d\n", - srds_prtcl_s4); - return -1; - } - - return 0; -} - -int board_early_init_r(void) -{ - const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; - int flash_esel = find_tlb_idx((void *)flashbase, 1); - - /* - * Remap Boot flash + PROMJET region to caching-inhibited - * so that flash can be erased properly. - */ - - /* Flush d-cache and invalidate i-cache of any FLASH data */ - flush_dcache(); - invalidate_icache(); - - if (flash_esel == -1) { - /* very unlikely unless something is messed up */ - puts("Error: Could not find TLB for FLASH BASE\n"); - flash_esel = 2; /* give our best effort to continue */ - } else { - /* invalidate existing TLB entry for flash + promjet */ - disable_tlb(flash_esel); - } - - set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, flash_esel, BOOKE_PAGESZ_256M, 1); - - /* Disable remote I2C connection to qixis fpga */ - QIXIS_WRITE(brdcfg[5], QIXIS_READ(brdcfg[5]) & ~BRDCFG5_IRE); - - /* - * Adjust core voltage according to voltage ID - * This function changes I2C mux to channel 2. - */ - if (adjust_vdd(0)) - printf("Warning: Adjusting core voltage failed.\n"); - - /* Configure board SERDES ports crossbar */ - config_frontside_crossbar_vsc3316(); - config_backside_crossbar_mux(); - select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0); - - return 0; -} - -unsigned long get_board_sys_clk(void) -{ - u8 sysclk_conf = QIXIS_READ(brdcfg[1]); -#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT - /* use accurate clock measurement */ - int freq = QIXIS_READ(clk_freq[0]) << 8 | QIXIS_READ(clk_freq[1]); - int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]); - u32 val; - - val = freq * base; - if (val) { - debug("SYS Clock measurement is: %d\n", val); - return val; - } else { - printf("Warning: SYS clock measurement is invalid, using value from brdcfg1.\n"); - } -#endif - - switch (sysclk_conf & 0x0F) { - case QIXIS_SYSCLK_83: - return 83333333; - case QIXIS_SYSCLK_100: - return 100000000; - case QIXIS_SYSCLK_125: - return 125000000; - case QIXIS_SYSCLK_133: - return 133333333; - case QIXIS_SYSCLK_150: - return 150000000; - case QIXIS_SYSCLK_160: - return 160000000; - case QIXIS_SYSCLK_166: - return 166666666; - } - return 66666666; -} - -unsigned long get_board_ddr_clk(void) -{ - u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); -#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT - /* use accurate clock measurement */ - int freq = QIXIS_READ(clk_freq[2]) << 8 | QIXIS_READ(clk_freq[3]); - int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]); - u32 val; - - val = freq * base; - if (val) { - debug("DDR Clock measurement is: %d\n", val); - return val; - } else { - printf("Warning: DDR clock measurement is invalid, using value from brdcfg1.\n"); - } -#endif - - switch ((ddrclk_conf & 0x30) >> 4) { - case QIXIS_DDRCLK_100: - return 100000000; - case QIXIS_DDRCLK_125: - return 125000000; - case QIXIS_DDRCLK_133: - return 133333333; - } - return 66666666; -} - -int misc_init_r(void) -{ - u8 sw; - void *srds_base = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; - serdes_corenet_t *srds_regs; - u32 actual[MAX_SERDES]; - u32 pllcr0, expected; - unsigned int i; - - sw = QIXIS_READ(brdcfg[2]); - for (i = 0; i < MAX_SERDES; i++) { - unsigned int clock = (sw >> (6 - 2 * i)) & 3; - switch (clock) { - case 0: - actual[i] = SRDS_PLLCR0_RFCK_SEL_100; - break; - case 1: - actual[i] = SRDS_PLLCR0_RFCK_SEL_125; - break; - case 2: - actual[i] = SRDS_PLLCR0_RFCK_SEL_156_25; - break; - case 3: - actual[i] = SRDS_PLLCR0_RFCK_SEL_161_13; - break; - } - } - - for (i = 0; i < MAX_SERDES; i++) { - srds_regs = srds_base + i * 0x1000; - pllcr0 = srds_regs->bank[0].pllcr0; - expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK; - if (expected != actual[i]) { - printf("Warning: SERDES%u expects reference clock %sMHz, but actual is %sMHz\n", - i + 1, serdes_clock_to_string(expected), - serdes_clock_to_string(actual[i])); - } - } - - return 0; -} - -int ft_board_setup(void *blob, bd_t *bd) -{ - phys_addr_t base; - phys_size_t size; - - ft_cpu_setup(blob, bd); - - base = env_get_bootm_low(); - size = env_get_bootm_size(); - - fdt_fixup_memory(blob, (u64)base, (u64)size); - -#ifdef CONFIG_PCI - pci_of_setup(blob, bd); -#endif - - fdt_fixup_liodn(blob); - fsl_fdt_fixup_dr_usb(blob, bd); - -#ifdef CONFIG_SYS_DPAA_FMAN -#ifndef CONFIG_DM_ETH - fdt_fixup_fman_ethernet(blob); -#endif - fdt_fixup_board_enet(blob); -#endif - - return 0; -} - -/* - * This function is called by bdinfo to print detail board information. - * As an exmaple for future board, we organize the messages into - * several sections. If applicable, the message is in the format of - * = - * It should aligned with normal output of bdinfo command. - * - * Voltage: Core, DDR and another configurable voltages - * Clock : Critical clocks which are not printed already - * RCW : RCW source if not printed already - * Misc : Other important information not in above catagories - */ -void board_detail(void) -{ - int i; - u8 brdcfg[16], dutcfg[16], rst_ctl; - int vdd, rcwsrc; - static const char * const clk[] = {"66.67", "100", "125", "133.33"}; - - for (i = 0; i < 16; i++) { - brdcfg[i] = qixis_read(offsetof(struct qixis, brdcfg[0]) + i); - dutcfg[i] = qixis_read(offsetof(struct qixis, dutcfg[0]) + i); - } - - /* Voltage secion */ - if (!select_i2c_ch_pca9547(I2C_MUX_CH_VOL_MONITOR, 0)) { - vdd = read_voltage(); - if (vdd > 0) - printf("Core voltage= %d mV\n", vdd); - select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0); - } - - printf("XVDD = 1.%d V\n", ((brdcfg[8] & 0xf) - 4) * 5 + 25); - - /* clock section */ - printf("SYSCLK = %s MHz\nDDRCLK = %s MHz\n", - clk[(brdcfg[11] >> 2) & 0x3], clk[brdcfg[11] & 3]); - - /* RCW section */ - rcwsrc = (dutcfg[0] << 1) + (dutcfg[1] & 1); - puts("RCW source = "); - switch (rcwsrc) { - case 0x017: - case 0x01f: - puts("8-bit NOR\n"); - break; - case 0x027: - case 0x02F: - puts("16-bit NOR\n"); - break; - case 0x040: - puts("SDHC/eMMC\n"); - break; - case 0x044: - puts("SPI 16-bit addressing\n"); - break; - case 0x045: - puts("SPI 24-bit addressing\n"); - break; - case 0x048: - puts("I2C normal addressing\n"); - break; - case 0x049: - puts("I2C extended addressing\n"); - break; - case 0x108: - case 0x109: - case 0x10a: - case 0x10b: - puts("8-bit NAND, 2KB\n"); - break; - default: - if ((rcwsrc >= 0x080) && (rcwsrc <= 0x09f)) - puts("Hard-coded RCW\n"); - else if ((rcwsrc >= 0x110) && (rcwsrc <= 0x11f)) - puts("8-bit NAND, 4KB\n"); - else - puts("unknown\n"); - break; - } - - /* Misc section */ - rst_ctl = QIXIS_READ(rst_ctl); - puts("HRESET_REQ = "); - switch (rst_ctl & 0x30) { - case 0x00: - puts("Ignored\n"); - break; - case 0x10: - puts("Assert HRESET\n"); - break; - case 0x30: - puts("Reset system\n"); - break; - default: - puts("N/A\n"); - break; - } -} - -/* - * Reverse engineering switch settings. - * Some bits cannot be figured out. They will be displayed as - * underscore in binary format. mask[] has those bits. - * Some bits are calculated differently than the actual switches - * if booting with overriding by FPGA. - */ -void qixis_dump_switch(void) -{ - int i; - u8 sw[9]; - - /* - * Any bit with 1 means that bit cannot be reverse engineered. - * It will be displayed as _ in binary format. - */ - static const u8 mask[] = {0, 0, 0, 0, 0, 0x1, 0xcf, 0x3f, 0x1f}; - char buf[10]; - u8 brdcfg[16], dutcfg[16]; - - for (i = 0; i < 16; i++) { - brdcfg[i] = qixis_read(offsetof(struct qixis, brdcfg[0]) + i); - dutcfg[i] = qixis_read(offsetof(struct qixis, dutcfg[0]) + i); - } - - sw[0] = dutcfg[0]; - sw[1] = (dutcfg[1] << 0x07) | - ((dutcfg[12] & 0xC0) >> 1) | - ((dutcfg[11] & 0xE0) >> 3) | - ((dutcfg[6] & 0x80) >> 6) | - ((dutcfg[1] & 0x80) >> 7); - sw[2] = ((brdcfg[1] & 0x0f) << 4) | - ((brdcfg[1] & 0x30) >> 2) | - ((brdcfg[1] & 0x40) >> 5) | - ((brdcfg[1] & 0x80) >> 7); - sw[3] = brdcfg[2]; - sw[4] = ((dutcfg[2] & 0x01) << 7) | - ((dutcfg[2] & 0x06) << 4) | - ((~QIXIS_READ(present)) & 0x10) | - ((brdcfg[3] & 0x80) >> 4) | - ((brdcfg[3] & 0x01) << 2) | - ((brdcfg[6] == 0x62) ? 3 : - ((brdcfg[6] == 0x5a) ? 2 : - ((brdcfg[6] == 0x5e) ? 1 : 0))); - sw[5] = ((brdcfg[0] & 0x0f) << 4) | - ((QIXIS_READ(rst_ctl) & 0x30) >> 2) | - ((brdcfg[0] & 0x40) >> 5); - sw[6] = (brdcfg[11] & 0x20) | - ((brdcfg[5] & 0x02) << 3); - sw[7] = (((~QIXIS_READ(rst_ctl)) & 0x40) << 1) | - ((brdcfg[5] & 0x10) << 2); - sw[8] = ((brdcfg[12] & 0x08) << 4) | - ((brdcfg[12] & 0x03) << 5); - - puts("DIP switch (reverse-engineering)\n"); - for (i = 0; i < 9; i++) { - printf("SW%d = 0b%s (0x%02x)\n", - i + 1, byte_to_binary_mask(sw[i], mask[i], buf), sw[i]); - } -} - -static int do_vdd_adjust(struct cmd_tbl *cmdtp, - int flag, int argc, - char *const argv[]) -{ - ulong override; - - if (argc < 2) - return CMD_RET_USAGE; - if (!strict_strtoul(argv[1], 10, &override)) - adjust_vdd(override); /* the value is checked by callee */ - else - return CMD_RET_USAGE; - - return 0; -} - -U_BOOT_CMD( - vdd_override, 2, 0, do_vdd_adjust, - "Override VDD", - "- override with the voltage specified in mV, eg. 1050" -); diff --git a/board/freescale/t4qds/t4240qds_qixis.h b/board/freescale/t4qds/t4240qds_qixis.h deleted file mode 100644 index 52e8d5a7be..0000000000 --- a/board/freescale/t4qds/t4240qds_qixis.h +++ /dev/null @@ -1,42 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2012 Freescale Semiconductor, Inc. - */ - -#ifndef __T4020QDS_QIXIS_H__ -#define __T4020QDS_QIXIS_H__ - -/* Definitions of QIXIS Registers for T4020QDS */ - -/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */ -#define BRDCFG4_EMISEL_MASK 0xE0 -#define BRDCFG4_EMISEL_SHIFT 5 - -/* SYSCLK */ -#define QIXIS_SYSCLK_66 0x0 -#define QIXIS_SYSCLK_83 0x1 -#define QIXIS_SYSCLK_100 0x2 -#define QIXIS_SYSCLK_125 0x3 -#define QIXIS_SYSCLK_133 0x4 -#define QIXIS_SYSCLK_150 0x5 -#define QIXIS_SYSCLK_160 0x6 -#define QIXIS_SYSCLK_166 0x7 - -/* DDRCLK */ -#define QIXIS_DDRCLK_66 0x0 -#define QIXIS_DDRCLK_100 0x1 -#define QIXIS_DDRCLK_125 0x2 -#define QIXIS_DDRCLK_133 0x3 - -#define BRDCFG5_IRE 0x20 /* i2c Remote i2c1 enable */ - -#define BRDCFG12_SD3EN_MASK 0x20 -#define BRDCFG12_SD3MX_MASK 0x08 -#define BRDCFG12_SD3MX_SLOT5 0x08 -#define BRDCFG12_SD3MX_SLOT6 0x00 -#define BRDCFG12_SD4EN_MASK 0x04 -#define BRDCFG12_SD4MX_MASK 0x03 -#define BRDCFG12_SD4MX_SLOT7 0x02 -#define BRDCFG12_SD4MX_SLOT8 0x01 -#define BRDCFG12_SD4MX_AURO_SATA 0x00 -#endif diff --git a/board/freescale/t4qds/t4_nand_rcw.cfg b/board/freescale/t4qds/t4_nand_rcw.cfg deleted file mode 100644 index 9386be0faa..0000000000 --- a/board/freescale/t4qds/t4_nand_rcw.cfg +++ /dev/null @@ -1,7 +0,0 @@ -#PBL preamble and RCW header -aa55aa55 010e0100 -#serdes protocol 1_27_5_11 -1607001b 18101b16 00000000 00000000 -04362858 30548c00 e8020000 f5000000 -00000000 ee0000ee 00000000 000307fc -00000000 00000000 00000000 00000028 diff --git a/board/freescale/t4qds/t4_pbi.cfg b/board/freescale/t4qds/t4_pbi.cfg deleted file mode 100644 index 8d460039bf..0000000000 --- a/board/freescale/t4qds/t4_pbi.cfg +++ /dev/null @@ -1,21 +0,0 @@ -#PBI commands -#Initialize CPC1 -09010000 00200400 -09138000 00000000 -091380c0 00000100 -#512KB SRAM -09010100 00000000 -09010104 fff80009 -09010f00 08000000 -#enable CPC1 -09010000 80000000 -#Configure LAW for CPC1 -09000d00 00000000 -09000d04 fff80000 -09000d08 81000012 -#Configure alternate space -09000010 00000000 -09000014 ff000000 -09000018 81000000 -#Flush PBL data -091380c0 00100000 diff --git a/board/freescale/t4qds/t4_sd_rcw.cfg b/board/freescale/t4qds/t4_sd_rcw.cfg deleted file mode 100644 index 54beb6783d..0000000000 --- a/board/freescale/t4qds/t4_sd_rcw.cfg +++ /dev/null @@ -1,7 +0,0 @@ -#PBL preamble and RCW header -aa55aa55 010e0100 -#serdes protocol 1_27_5_11 -1607001b 18101b16 00000000 00000000 -04362858 30548c00 68020000 f5000000 -00000000 ee0000ee 00000000 000307fc -00000000 00000000 00000000 00000028 diff --git a/board/freescale/t4qds/t4qds.h b/board/freescale/t4qds/t4qds.h deleted file mode 100644 index 4a8e91b58f..0000000000 --- a/board/freescale/t4qds/t4qds.h +++ /dev/null @@ -1,12 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -#ifndef __CORENET_DS_H__ -#define __CORENET_DS_H__ - -void fdt_fixup_board_enet(void *blob); -void pci_of_setup(void *blob, bd_t *bd); - -#endif diff --git a/board/freescale/t4qds/tlb.c b/board/freescale/t4qds/tlb.c deleted file mode 100644 index cd5cf48def..0000000000 --- a/board/freescale/t4qds/tlb.c +++ /dev/null @@ -1,146 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2008-2012 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -#include -#include - -struct fsl_e_tlb_entry tlb_table[] = { - /* TLB 0 - for temp stack in cache */ - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, - CONFIG_SYS_INIT_RAM_ADDR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, - CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 0, BOOKE_PAGESZ_4K, 0), - - /* TLB 1 */ - /* *I*** - Covers boot page */ -#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) - /* - * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the - * SRAM is at 0xfff00000, it covered the 0xfffff000. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_1M, 1), -#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) - /* - * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the - * space is at 0xfff00000, it covered the 0xfffff000. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR, - CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, - 0, 0, BOOKE_PAGESZ_1M, 1), -#else - SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_4K, 1), -#endif - - /* *I*G* - CCSRBAR */ - SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 1, BOOKE_PAGESZ_16M, 1), - - /* *I*G* - Flash, localbus */ - /* This will be changed to *I*G* after relocation to RAM. */ - SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, - MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, - 0, 2, BOOKE_PAGESZ_256M, 1), -#ifndef CONFIG_SPL_BUILD - /* *I*G* - PCI */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 3, BOOKE_PAGESZ_1G, 1), - - /* *I*G* - PCI */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000, - CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 4, BOOKE_PAGESZ_256M, 1), - - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000, - CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 5, BOOKE_PAGESZ_256M, 1), - - /* *I*G* - PCI I/O */ - SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 6, BOOKE_PAGESZ_256K, 1), - - /* Bman/Qman */ -#ifdef CONFIG_SYS_BMAN_MEM_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 9, BOOKE_PAGESZ_16M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, - CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 10, BOOKE_PAGESZ_16M, 1), -#endif -#ifdef CONFIG_SYS_QMAN_MEM_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 11, BOOKE_PAGESZ_16M, 1), - SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, - CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 12, BOOKE_PAGESZ_16M, 1), -#endif -#endif -#ifdef CONFIG_SYS_DCSRBAR_PHYS - SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 13, BOOKE_PAGESZ_32M, 1), -#endif -#ifdef CONFIG_SYS_NAND_BASE - /* - * *I*G - NAND - * entry 14 and 15 has been used hard coded, they will be disabled - * in cpu_init_f, so we use entry 16 for nand. - */ - SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 16, BOOKE_PAGESZ_64K, 1), -#endif -#ifdef QIXIS_BASE_PHYS - SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 17, BOOKE_PAGESZ_4K, 1), -#endif -#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE - /* - * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for - * fetching ucode and ENV from master - */ - SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR, - CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, - 0, 18, BOOKE_PAGESZ_1M, 1), -#endif - -#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD) - SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M, - 0, 19, BOOKE_PAGESZ_2G, 1) -#endif -}; - -int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/configs/T4160QDS_NAND_defconfig b/configs/T4160QDS_NAND_defconfig deleted file mode 100644 index ddff89602f..0000000000 --- a/configs/T4160QDS_NAND_defconfig +++ /dev/null @@ -1,69 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x140000 -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T4160QDS=y -CONFIG_SYS_CUSTOM_LDSCRIPT=y -CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL" -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_NAND_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_SPL_NAND_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_ENV_IS_IN_NAND=y -CONFIG_FSL_CAAM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_MTD_RAW_NAND=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NAND=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T4160QDS_SDCARD_defconfig b/configs/T4160QDS_SDCARD_defconfig deleted file mode 100644 index 5d253534ca..0000000000 --- a/configs/T4160QDS_SDCARD_defconfig +++ /dev/null @@ -1,66 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x100000 -CONFIG_SPL_MMC_SUPPORT=y -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T4160QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SDCARD" -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_MMC_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_ENV_IS_IN_MMC=y -CONFIG_FSL_CAAM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_MMC=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T4160QDS_SECURE_BOOT_defconfig b/configs/T4160QDS_SECURE_BOOT_defconfig deleted file mode 100644 index 8934c3edf0..0000000000 --- a/configs/T4160QDS_SECURE_BOOT_defconfig +++ /dev/null @@ -1,56 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_NXP_ESBC=y -CONFIG_MPC85xx=y -CONFIG_TARGET_T4160QDS=y -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_DM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_RSA=y -CONFIG_SPL_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T4160QDS_defconfig b/configs/T4160QDS_defconfig deleted file mode 100644 index d0d1290631..0000000000 --- a/configs/T4160QDS_defconfig +++ /dev/null @@ -1,53 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T4160QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xEFF20000 -CONFIG_FSL_CAAM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T4240QDS_NAND_defconfig b/configs/T4240QDS_NAND_defconfig deleted file mode 100644 index f971cee3b0..0000000000 --- a/configs/T4240QDS_NAND_defconfig +++ /dev/null @@ -1,69 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x140000 -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T4240QDS=y -CONFIG_SYS_CUSTOM_LDSCRIPT=y -CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL" -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_NAND_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_SPL_NAND_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_ENV_IS_IN_NAND=y -CONFIG_FSL_CAAM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_MTD_RAW_NAND=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NAND=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T4240QDS_SDCARD_defconfig b/configs/T4240QDS_SDCARD_defconfig deleted file mode 100644 index 5e662be1d7..0000000000 --- a/configs/T4240QDS_SDCARD_defconfig +++ /dev/null @@ -1,66 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0x00201000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x100000 -CONFIG_SPL_MMC_SUPPORT=y -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y -CONFIG_SPL=y -CONFIG_SPL_TEXT_BASE=0xFFFD8000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T4240QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SDCARD" -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -# CONFIG_SPL_FRAMEWORK is not set -CONFIG_SPL_MMC_BOOT=y -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_ENV_IS_IN_MMC=y -CONFIG_FSL_CAAM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_MMC=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T4240QDS_SECURE_BOOT_defconfig b/configs/T4240QDS_SECURE_BOOT_defconfig deleted file mode 100644 index 807d5b5895..0000000000 --- a/configs/T4240QDS_SECURE_BOOT_defconfig +++ /dev/null @@ -1,56 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_NXP_ESBC=y -CONFIG_MPC85xx=y -CONFIG_TARGET_T4240QDS=y -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_DM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_RSA=y -CONFIG_SPL_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T4240QDS_SRIO_PCIE_BOOT_defconfig b/configs/T4240QDS_SRIO_PCIE_BOOT_defconfig deleted file mode 100644 index 2bc30bbf9e..0000000000 --- a/configs/T4240QDS_SRIO_PCIE_BOOT_defconfig +++ /dev/null @@ -1,49 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xFFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T4240QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_SYS_EXTRA_OPTIONS="SRIO_PCIE_BOOT_SLAVE" -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_GREPENV=y -# CONFIG_CMD_FLASH is not set -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_ENV_IS_IN_REMOTE=y -CONFIG_ENV_ADDR=0xFFE20000 -CONFIG_FSL_CAAM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_REMOTE=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/configs/T4240QDS_defconfig b/configs/T4240QDS_defconfig deleted file mode 100644 index 84341f7579..0000000000 --- a/configs/T4240QDS_defconfig +++ /dev/null @@ -1,53 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xEFF40000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_MPC85xx=y -CONFIG_TARGET_T4240QDS=y -CONFIG_FIT=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -CONFIG_BOARD_EARLY_INIT_R=y -CONFIG_HUSH_PARSER=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_SF=y -CONFIG_CMD_USB=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_MP=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xEFF20000 -CONFIG_FSL_CAAM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SPI_FLASH=y -CONFIG_SF_DEFAULT_MODE=0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_MII=y -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_FSL_ESPI=y -CONFIG_USB=y -CONFIG_USB_STORAGE=y -CONFIG_OF_LIBFDT=y diff --git a/include/configs/T4240QDS.h b/include/configs/T4240QDS.h deleted file mode 100644 index d92af7202b..0000000000 --- a/include/configs/T4240QDS.h +++ /dev/null @@ -1,555 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -/* - * T4240 QDS board configuration file - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#include - -#define CONFIG_FSL_SATA_V2 -#define CONFIG_PCIE4 - -#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ - -#ifdef CONFIG_RAMBOOT_PBL -#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t4qds/t4_pbi.cfg -#if !defined(CONFIG_MTD_RAW_NAND) && !defined(CONFIG_SDCARD) -#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#else -#define CONFIG_SPL_FLUSH_IMAGE -#define CONFIG_SPL_PAD_TO 0x40000 -#define CONFIG_SPL_MAX_SIZE 0x28000 -#define RESET_VECTOR_OFFSET 0x27FFC -#define BOOT_PAGE_OFFSET 0x27000 - -#ifdef CONFIG_MTD_RAW_NAND -#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 -#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 -#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) -#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t4qds/t4_nand_rcw.cfg -#endif - -#ifdef CONFIG_SDCARD -#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC -#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_MMC_U_BOOT_DST 0x00200000 -#define CONFIG_SYS_MMC_U_BOOT_START 0x00200000 -#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) -#ifndef CONFIG_SPL_BUILD -#define CONFIG_SYS_MPC85XX_NO_RESETVEC -#endif -#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t4qds/t4_sd_rcw.cfg -#endif - -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SPL_SKIP_RELOCATE -#define CONFIG_SPL_COMMON_INIT_DDR -#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE -#endif - -#endif -#endif /* CONFIG_RAMBOOT_PBL */ - -#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE -/* Set 1M boot space */ -#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) -#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ - (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) -#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc -#endif - -#define CONFIG_SRIO_PCIE_BOOT_MASTER -#define CONFIG_DDR_ECC - -#include "t4qds.h" - -#if defined(CONFIG_SPIFLASH) -#elif defined(CONFIG_SDCARD) -#define CONFIG_SYS_MMC_ENV_DEV 0 -#endif - -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() -#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() - -#ifndef __ASSEMBLY__ -unsigned long get_board_sys_clk(void); -unsigned long get_board_ddr_clk(void); -#endif - -/* EEPROM */ -#define CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_NXID -#define CONFIG_SYS_EEPROM_BUS_NUM 0 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -/* - * DDR Setup - */ -#define CONFIG_SYS_SPD_BUS_NUM 0 -#define SPD_EEPROM_ADDRESS1 0x51 -#define SPD_EEPROM_ADDRESS2 0x52 -#define SPD_EEPROM_ADDRESS3 0x53 -#define SPD_EEPROM_ADDRESS4 0x54 -#define SPD_EEPROM_ADDRESS5 0x55 -#define SPD_EEPROM_ADDRESS6 0x56 -#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */ -#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ - -/* - * IFC Definitions - */ -#define CONFIG_SYS_NOR0_CSPR_EXT (0xf) -#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ - + 0x8000000) | \ - CSPR_PORT_SIZE_16 | \ - CSPR_MSEL_NOR | \ - CSPR_V) -#define CONFIG_SYS_NOR1_CSPR_EXT (0xf) -#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ - CSPR_PORT_SIZE_16 | \ - CSPR_MSEL_NOR | \ - CSPR_V) -#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) -/* NOR Flash Timing Params */ -#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 - -#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ - FTIM0_NOR_TEADC(0x5) | \ - FTIM0_NOR_TEAHC(0x5)) -#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ - FTIM1_NOR_TRAD_NOR(0x1A) |\ - FTIM1_NOR_TSEQRAD_NOR(0x13)) -#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ - FTIM2_NOR_TCH(0x4) | \ - FTIM2_NOR_TWPH(0x0E) | \ - FTIM2_NOR_TWP(0x1c)) -#define CONFIG_SYS_NOR_FTIM3 0x0 - -#define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ - + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} - -#define CONFIG_FSL_QIXIS /* use common QIXIS code */ -#define QIXIS_BASE 0xffdf0000 -#define QIXIS_LBMAP_SWITCH 6 -#define QIXIS_LBMAP_MASK 0x0f -#define QIXIS_LBMAP_SHIFT 0 -#define QIXIS_LBMAP_DFLTBANK 0x00 -#define QIXIS_LBMAP_ALTBANK 0x04 -#define QIXIS_RST_CTL_RESET 0x83 -#define QIXIS_RST_FORCE_MEM 0x1 -#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 -#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 -#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 -#define QIXIS_BRDCFG5 0x55 -#define QIXIS_MUX_SDHC 2 -#define QIXIS_MUX_SDHC_WIDTH8 1 -#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) - -#define CONFIG_SYS_CSPR3_EXT (0xf) -#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ - | CSPR_PORT_SIZE_8 \ - | CSPR_MSEL_GPCM \ - | CSPR_V) -#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024) -#define CONFIG_SYS_CSOR3 0x0 -/* QIXIS Timing parameters for IFC CS3 */ -#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ - FTIM0_GPCM_TEADC(0x0e) | \ - FTIM0_GPCM_TEAHC(0x0e)) -#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ - FTIM1_GPCM_TRAD(0x3f)) -#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ - FTIM2_GPCM_TCH(0x8) | \ - FTIM2_GPCM_TWP(0x1f)) -#define CONFIG_SYS_CS3_FTIM3 0x0 - -/* NAND Flash on IFC */ -#define CONFIG_NAND_FSL_IFC -#define CONFIG_SYS_NAND_BASE 0xff800000 -#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) - -#define CONFIG_SYS_NAND_CSPR_EXT (0xf) -#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ - | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ - | CSPR_MSEL_NAND /* MSEL = NAND */ \ - | CSPR_V) -#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) - -#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ - | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ - | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ - | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ - | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ - | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ - | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ - -#define CONFIG_SYS_NAND_ONFI_DETECTION - -/* ONFI NAND Flash mode0 Timing Params */ -#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ - FTIM0_NAND_TWP(0x18) | \ - FTIM0_NAND_TWCHT(0x07) | \ - FTIM0_NAND_TWH(0x0a)) -#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ - FTIM1_NAND_TWBE(0x39) | \ - FTIM1_NAND_TRR(0x0e) | \ - FTIM1_NAND_TRP(0x18)) -#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ - FTIM2_NAND_TREH(0x0a) | \ - FTIM2_NAND_TWHRE(0x1e)) -#define CONFIG_SYS_NAND_FTIM3 0x0 - -#define CONFIG_SYS_NAND_DDR_LAW 11 - -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } -#define CONFIG_SYS_MAX_NAND_DEVICE 1 - -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) -#define CONFIG_SYS_NAND_MAX_OOBFREE 2 -#define CONFIG_SYS_NAND_MAX_ECCPOS 256 - -#if defined(CONFIG_MTD_RAW_NAND) -#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT -#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR -#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK -#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR -#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 -#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 -#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 -#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 -#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT -#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR -#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 -#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT -#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR -#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 -#else -#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT -#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR -#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 -#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT -#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR -#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 -#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT -#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR -#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK -#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR -#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 -#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 -#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 -#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 -#endif - -#if defined(CONFIG_RAMBOOT_PBL) -#define CONFIG_SYS_RAMBOOT -#endif - -/* I2C */ -#ifndef CONFIG_DM_I2C -#define CONFIG_SYS_I2C -#else -#undef CONFIG_SYS_I2C -#undef CONFIG_SYS_FSL_I2C2_OFFSET -#undef CONFIG_SYS_FSL_I2C2_SLAVE -#undef CONFIG_SYS_FSL_I2C2_SPEED -#undef CONFIG_SYS_FSL_I2C_SLAVE -#undef CONFIG_SYS_FSL_I2C_SPEED -#undef CONFIG_SYS_FSL_I2C_OFFSET -#endif - -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 100000 /* I2C speed */ -#define CONFIG_SYS_FSL_I2C2_SPEED 100000 /* I2C2 speed */ -#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ -#define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */ - -#define I2C_MUX_CH_DEFAULT 0x8 -#define I2C_MUX_CH_VOL_MONITOR 0xa -#define I2C_MUX_CH_VSC3316_FS 0xc -#define I2C_MUX_CH_VSC3316_BS 0xd - -/* Voltage monitor on channel 2*/ -#define I2C_VOL_MONITOR_ADDR 0x40 -#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 -#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 -#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 - -/* VSC Crossbar switches */ -#define CONFIG_VSC_CROSSBAR -#define VSC3316_FSM_TX_ADDR 0x70 -#define VSC3316_FSM_RX_ADDR 0x71 - -/* - * RapidIO - */ - -/* - * for slave u-boot IMAGE instored in master memory space, - * PHYS must be aligned based on the SIZE - */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ -#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull -/* - * for slave UCODE and ENV instored in master memory space, - * PHYS must be aligned based on the SIZE - */ -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull -#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ - -/* slave core release by master*/ -#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 -#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ - -/* - * SRIO_PCIE_BOOT - SLAVE - */ -#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE -#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 -#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ - (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) -#endif -/* - * eSPI - Enhanced SPI - */ - -/* Qman/Bman */ -#ifndef CONFIG_NOBQFMAN -#define CONFIG_SYS_BMAN_NUM_PORTALS 50 -#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 -#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull -#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 -#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 -#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 -#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE -#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ - CONFIG_SYS_BMAN_CENA_SIZE) -#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 -#define CONFIG_SYS_QMAN_NUM_PORTALS 50 -#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 -#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull -#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 -#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 -#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 -#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE -#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ - CONFIG_SYS_QMAN_CENA_SIZE) -#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) -#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 - -#define CONFIG_SYS_DPAA_FMAN -#define CONFIG_SYS_DPAA_PME -#define CONFIG_SYS_PMAN -#define CONFIG_SYS_DPAA_DCE -#define CONFIG_SYS_DPAA_RMAN -#define CONFIG_SYS_INTERLAKEN - -/* Default address of microcode for the Linux Fman driver */ -#if defined(CONFIG_SPIFLASH) -/* - * env is stored at 0x100000, sector size is 0x10000, ucode is stored after - * env, so we got 0x110000. - */ -#define CONFIG_SYS_FMAN_FW_ADDR 0x110000 -#elif defined(CONFIG_SDCARD) -/* - * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is - * about 1MB (2048 blocks), Env is stored after the image, and the env size is - * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. - */ -#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) -#elif defined(CONFIG_MTD_RAW_NAND) -#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE) -#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) -/* - * Slave has no ucode locally, it can fetch this from remote. When implementing - * in two corenet boards, slave's ucode could be stored in master's memory - * space, the address can be mapped from slave TLB->slave LAW-> - * slave SRIO or PCIE outbound window->master inbound window-> - * master LAW->the ucode address in master's memory space. - */ -#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 -#else -#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 -#endif -#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 -#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) -#endif /* CONFIG_NOBQFMAN */ - -#ifdef CONFIG_SYS_DPAA_FMAN -#define SGMII_CARD_PORT1_PHY_ADDR 0x1C -#define SGMII_CARD_PORT2_PHY_ADDR 0x1D -#define SGMII_CARD_PORT3_PHY_ADDR 0x1E -#define SGMII_CARD_PORT4_PHY_ADDR 0x1F -#define FM1_10GEC1_PHY_ADDR 0x0 -#define FM1_10GEC2_PHY_ADDR 0x1 -#define FM2_10GEC1_PHY_ADDR 0x2 -#define FM2_10GEC2_PHY_ADDR 0x3 -#endif - -/* SATA */ -#ifdef CONFIG_FSL_SATA_V2 -#define CONFIG_SYS_SATA_MAX_DEVICE 2 -#define CONFIG_SATA1 -#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR -#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA -#define CONFIG_SATA2 -#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR -#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA - -#define CONFIG_LBA48 -#endif - -#ifdef CONFIG_FMAN_ENET -#define CONFIG_ETHPRIME "FM1@DTSEC1" -#endif - -/* -* USB -*/ -#define CONFIG_USB_EHCI_FSL -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_HAS_FSL_DR_USB - -#ifdef CONFIG_MMC -#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR -#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT -#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 -#define CONFIG_ESDHC_DETECT_QUIRK \ - (!(readb(QIXIS_BASE + QIXIS_BRDCFG5) & QIXIS_MUX_SDHC) || \ - IS_SVR_REV(get_svr(), 1, 0)) -#define CONFIG_ESDHC_DETECT_8_BIT_QUIRK \ - (!(readb(QIXIS_BASE + QIXIS_BRDCFG5) & QIXIS_MUX_SDHC_WIDTH8)) -#endif - - -#define __USB_PHY_TYPE utmi - -/* - * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be - * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way - * interleaving. It can be cacheline, page, bank, superbank. - * See doc/README.fsl-ddr for details. - */ -#ifdef CONFIG_ARCH_T4240 -#define CTRL_INTLV_PREFERED 3way_4KB -#else -#define CTRL_INTLV_PREFERED cacheline -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "hwconfig=fsl_ddr:" \ - "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ - "bank_intlv=auto;" \ - "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ - "netdev=eth0\0" \ - "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ - "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ - "tftpflash=tftpboot $loadaddr $uboot && " \ - "protect off $ubootaddr +$filesize && " \ - "erase $ubootaddr +$filesize && " \ - "cp.b $loadaddr $ubootaddr $filesize && " \ - "protect on $ubootaddr +$filesize && " \ - "cmp.b $loadaddr $ubootaddr $filesize\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=2000000\0" \ - "ramdiskfile=t4240qds/ramdisk.uboot\0" \ - "fdtaddr=1e00000\0" \ - "fdtfile=t4240qds/t4240qds.dtb\0" \ - "bdev=sda3\0" - -#define CONFIG_HVBOOT \ - "setenv bootargs config-addr=0x60000000; " \ - "bootm 0x01000000 - 0x00f00000" - -#define CONFIG_ALU \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "cpu 1 release 0x01000000 - - -;" \ - "cpu 2 release 0x01000000 - - -;" \ - "cpu 3 release 0x01000000 - - -;" \ - "cpu 4 release 0x01000000 - - -;" \ - "cpu 5 release 0x01000000 - - -;" \ - "cpu 6 release 0x01000000 - - -;" \ - "cpu 7 release 0x01000000 - - -;" \ - "go 0x01000000" - -#define CONFIG_LINUX \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "setenv ramdiskaddr 0x02000000;" \ - "setenv fdtaddr 0x00c00000;" \ - "setenv loadaddr 0x1000000;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_HDBOOT \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_LINUX - -#include - -#endif /* __CONFIG_H */