From: Fabio Estevam Date: Sun, 14 Feb 2021 01:49:52 +0000 (-0300) Subject: mx53loco: Convert to driver model X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=5c8db4922d42084fd29b36fcac287fe067d26f31;p=u-boot.git mx53loco: Convert to driver model Make the conversion to driver model as it is mandatory. Remove the SATA support for now as the i.MX53 support has not been added yet. Signed-off-by: Fabio Estevam --- diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 33e483f4fb..b28d179467 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -652,6 +652,7 @@ dtb-$(CONFIG_MX28) += \ imx28-xea.dtb dtb-$(CONFIG_MX53) += imx53-cx9020.dtb \ + imx53-qsb.dtb \ imx53-kp.dtb \ imx53-m53menlo.dtb diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c index ee54a61d87..0888630569 100644 --- a/board/freescale/mx53loco/mx53loco.c +++ b/board/freescale/mx53loco/mx53loco.c @@ -18,10 +18,8 @@ #include #include #include -#include #include #include -#include #include #include #include @@ -62,127 +60,6 @@ static void setup_iomux_uart(void) imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads)); } -#ifdef CONFIG_USB_EHCI_MX5 -int board_ehci_hcd_init(int port) -{ - /* request VBUS power enable pin, GPIO7_8 */ - imx_iomux_v3_setup_pad(MX53_PAD_PATA_DA_2__GPIO7_8); - gpio_direction_output(IMX_GPIO_NR(7, 8), 1); - return 0; -} -#endif - -static void setup_iomux_fec(void) -{ - static const iomux_v3_cfg_t fec_pads[] = { - NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS | - PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE), - NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH), - NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1, - PAD_CTL_HYS | PAD_CTL_PKE), - NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0, - PAD_CTL_HYS | PAD_CTL_PKE), - NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH), - NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH), - NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH), - NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK, - PAD_CTL_HYS | PAD_CTL_PKE), - NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER, - PAD_CTL_HYS | PAD_CTL_PKE), - NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV, - PAD_CTL_HYS | PAD_CTL_PKE), - }; - - imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads)); -} - -#ifdef CONFIG_FSL_ESDHC_IMX -struct fsl_esdhc_cfg esdhc_cfg[2] = { - {MMC_SDHC1_BASE_ADDR}, - {MMC_SDHC3_BASE_ADDR}, -}; - -int board_mmc_getcd(struct mmc *mmc) -{ - struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; - int ret; - - imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA11__GPIO3_11); - gpio_direction_input(IMX_GPIO_NR(3, 11)); - imx_iomux_v3_setup_pad(MX53_PAD_EIM_DA13__GPIO3_13); - gpio_direction_input(IMX_GPIO_NR(3, 13)); - - if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR) - ret = !gpio_get_value(IMX_GPIO_NR(3, 13)); - else - ret = !gpio_get_value(IMX_GPIO_NR(3, 11)); - - return ret; -} - -#define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \ - PAD_CTL_PUS_100K_UP) -#define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \ - PAD_CTL_DSE_HIGH) - -int board_mmc_init(struct bd_info *bis) -{ - static const iomux_v3_cfg_t sd1_pads[] = { - NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL), - MX53_PAD_EIM_DA13__GPIO3_13, - }; - - static const iomux_v3_cfg_t sd2_pads[] = { - NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD, - SD_CMD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL), - NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL), - MX53_PAD_EIM_DA11__GPIO3_11, - }; - - u32 index; - int ret; - - esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); - esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); - - for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) { - switch (index) { - case 0: - imx_iomux_v3_setup_multiple_pads(sd1_pads, - ARRAY_SIZE(sd1_pads)); - break; - case 1: - imx_iomux_v3_setup_multiple_pads(sd2_pads, - ARRAY_SIZE(sd2_pads)); - break; - default: - printf("Warning: you configured more ESDHC controller" - "(%d) as supported by the board(2)\n", - CONFIG_SYS_FSL_ESDHC_NUM); - return -EINVAL; - } - ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]); - if (ret) - return ret; - } - - return 0; -} -#endif - #define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \ PAD_CTL_PUS_100K_UP | PAD_CTL_ODE) @@ -327,7 +204,6 @@ static void clock_1GHz(void) int board_early_init_f(void) { setup_iomux_uart(); - setup_iomux_fec(); setup_iomux_lcd(); return 0; diff --git a/configs/mx53loco_defconfig b/configs/mx53loco_defconfig index a1096a7f93..2828889b03 100644 --- a/configs/mx53loco_defconfig +++ b/configs/mx53loco_defconfig @@ -1,11 +1,14 @@ CONFIG_ARM=y CONFIG_ARCH_MX5=y CONFIG_SYS_TEXT_BASE=0x77800000 +CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_NR_DRAM_BANKS=2 CONFIG_ENV_SIZE=0x2000 CONFIG_ENV_OFFSET=0xC0000 CONFIG_TARGET_MX53LOCO=y +CONFIG_DM_GPIO=y # CONFIG_CMD_BMODE is not set +CONFIG_DEFAULT_DEVICE_TREE="imx53-qsb" CONFIG_SUPPORT_RAW_INITRD=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx53loco/imximage.cfg" CONFIG_USE_PREBOOT=y @@ -13,8 +16,9 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y +CONFIG_CMD_DM=y CONFIG_CMD_MMC=y -CONFIG_CMD_SATA=y +# CONFIG_CMD_PINMUX is not set CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -23,15 +27,28 @@ CONFIG_CMD_PING=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y +CONFIG_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_MMC=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_DWC_AHSATA=y +CONFIG_DM=y +CONFIG_DM_MMC=y CONFIG_FSL_ESDHC_IMX=y CONFIG_MTD=y +CONFIG_PHYLIB=y +CONFIG_PHY_SMSC=y +CONFIG_PHY_FIXED=y +CONFIG_DM_ETH=y +CONFIG_FEC_MXC=y CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX5=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y CONFIG_MXC_UART=y CONFIG_USB=y +CONFIG_DM_USB=y CONFIG_USB_EHCI_MX5=y CONFIG_USB_STORAGE=y CONFIG_USB_HOST_ETHER=y @@ -40,4 +57,3 @@ CONFIG_USB_ETHER_MCS7830=y CONFIG_USB_ETHER_SMSC95XX=y CONFIG_SYS_WHITE_ON_BLACK=y CONFIG_SPLASH_SCREEN=y -CONFIG_OF_LIBFDT=y diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h index a0dd33aecd..e5dc9ac1d9 100644 --- a/include/configs/mx53loco.h +++ b/include/configs/mx53loco.h @@ -30,12 +30,6 @@ #define CONFIG_SYS_FSL_ESDHC_ADDR 0 #define CONFIG_SYS_FSL_ESDHC_NUM 2 -/* Eth Configs */ - -#define CONFIG_FEC_MXC -#define IMX_FEC_BASE FEC_BASE_ADDR -#define CONFIG_FEC_MXC_PHYADDR 0x1F - /* USB Configs */ #define CONFIG_MXC_USB_PORT 1 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)