From: Tom Rini Date: Sat, 22 May 2021 12:47:14 +0000 (-0400) Subject: arm: Remove spear600 boards and the rest of SPEAr support X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=570c3dcfc153e0f18bd897630236da6605dcbe7e;p=u-boot.git arm: Remove spear600 boards and the rest of SPEAr support These boards have not been converted to CONFIG_DM_USB by the deadline and is also missing conversion to CONFIG_DM. Remove them. As this is the last of the SPEAr platforms, so remove the rest of the remaining support as well. Cc: Vipin Kumar Signed-off-by: Tom Rini --- diff --git a/Makefile b/Makefile index d9473fb572..0d3192ceba 100644 --- a/Makefile +++ b/Makefile @@ -1561,22 +1561,11 @@ u-boot-signed.sb: u-boot.bin spl/u-boot-spl.bin u-boot.sb: u-boot.bin spl/u-boot-spl.bin $(Q)$(MAKE) $(build)=arch/arm/cpu/arm926ejs/mxs u-boot.sb -# On x600 (SPEAr600) U-Boot is appended to U-Boot SPL. -# Both images are created using mkimage (crc etc), so that the ROM -# bootloader can check its integrity. Padding needs to be done to the -# SPL image (with mkimage header) and not the binary. Otherwise the resulting image -# which is loaded/copied by the ROM bootloader to SRAM doesn't fit. -# The resulting image containing both U-Boot images is called u-boot.spr MKIMAGEFLAGS_u-boot-spl.img = -A $(ARCH) -T firmware -C none \ -a $(CONFIG_SPL_TEXT_BASE) -e $(CONFIG_SPL_TEXT_BASE) -n XLOADER spl/u-boot-spl.img: spl/u-boot-spl.bin FORCE $(call if_changed,mkimage) -OBJCOPYFLAGS_u-boot.spr = -I binary -O binary --pad-to=$(CONFIG_SPL_PAD_TO) \ - --gap-fill=0xff -u-boot.spr: spl/u-boot-spl.img u-boot.img FORCE - $(call if_changed,pad_cat) - ifneq ($(CONFIG_ARCH_SOCFPGA),) quiet_cmd_gensplx4 = GENSPLX4 $@ cmd_gensplx4 = $(OBJCOPY) -I binary -O binary --gap-fill=0x0 \ diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 512b2c73ab..7f493a8e8f 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -566,14 +566,6 @@ config ARCH_ORION5X select CPU_ARM926EJS select GPIO_EXTRA_HEADER -config TARGET_SPEAR600 - bool "Support spear600" - select BOARD_EARLY_INIT_F - select CPU_ARM926EJS - select GPIO_EXTRA_HEADER - select PL011_SERIAL - imply CMD_SAVES - config TARGET_STV0991 bool "Support stv0991" select CPU_V7A @@ -587,14 +579,6 @@ config TARGET_STV0991 select SPI_FLASH imply CMD_DM -config TARGET_X600 - bool "Support x600" - select BOARD_LATE_INIT - select CPU_ARM926EJS - select GPIO_EXTRA_HEADER - select PL011_SERIAL - select SUPPORT_SPL - config TARGET_FLEA3 bool "Support flea3" select CPU_ARM1136 @@ -2098,8 +2082,6 @@ source "board/kontron/sl28/Kconfig" source "board/myir/mys_6ulx/Kconfig" source "board/seeed/npi_imx6ull/Kconfig" source "board/socionext/developerbox/Kconfig" -source "board/spear/spear600/Kconfig" -source "board/spear/x600/Kconfig" source "board/st/stv0991/Kconfig" source "board/tcl/sl50/Kconfig" source "board/toradex/colibri_pxa270/Kconfig" diff --git a/arch/arm/cpu/arm926ejs/spear/Makefile b/arch/arm/cpu/arm926ejs/spear/Makefile deleted file mode 100644 index b1b6b4028b..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/Makefile +++ /dev/null @@ -1,21 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. - -obj-y := cpu.o \ - reset.o \ - timer.o - -ifdef CONFIG_SPL_BUILD -obj-y += spl.o -obj-$(CONFIG_SPEAR600) += spear600.o -obj-$(CONFIG_DDR_MT47H64M16) += spr600_mt47h64m16_3_333_cl5_psync.o -obj-$(CONFIG_DDR_MT47H32M16) += spr600_mt47h32m16_333_cl5_psync.o -obj-$(CONFIG_DDR_MT47H32M16) += spr600_mt47h32m16_37e_166_cl4_sync.o -obj-$(CONFIG_DDR_MT47H128M8) += spr600_mt47h128m8_3_266_cl5_async.o -else -obj-y += spr_misc.o spr_lowlevel_init.o -endif - -extra-$(CONFIG_SPL_BUILD) := start.o diff --git a/arch/arm/cpu/arm926ejs/spear/cpu.c b/arch/arm/cpu/arm926ejs/spear/cpu.c deleted file mode 100644 index 2e0dd9ec33..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/cpu.c +++ /dev/null @@ -1,108 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2010 - * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. - */ - -#include -#include -#include -#include -#include -#include - -int arch_cpu_init(void) -{ - struct misc_regs *const misc_p = - (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - u32 periph1_clken, periph_clk_cfg; - - periph1_clken = readl(&misc_p->periph1_clken); - -#if defined(CONFIG_SPEAR600) - periph1_clken |= MISC_GPT3ENB; -#endif - -#if defined(CONFIG_PL011_SERIAL) - periph1_clken |= MISC_UART0ENB; - - periph_clk_cfg = readl(&misc_p->periph_clk_cfg); - periph_clk_cfg &= ~CONFIG_SPEAR_UARTCLKMSK; - periph_clk_cfg |= CONFIG_SPEAR_UART48M; - writel(periph_clk_cfg, &misc_p->periph_clk_cfg); -#endif -#if defined(CONFIG_ETH_DESIGNWARE) - periph1_clken |= MISC_ETHENB; -#endif -#if defined(CONFIG_DW_UDC) - periph1_clken |= MISC_USBDENB; -#endif -#if defined(CONFIG_SYS_I2C_DW) - periph1_clken |= MISC_I2CENB; -#endif -#if defined(CONFIG_ST_SMI) - periph1_clken |= MISC_SMIENB; -#endif -#if defined(CONFIG_NAND_FSMC) - periph1_clken |= MISC_FSMCENB; -#endif -#if defined(CONFIG_USB_EHCI_SPEAR) - periph1_clken |= PERIPH_USBH1 | PERIPH_USBH2; -#endif -#if defined(CONFIG_SPEAR_GPIO) - periph1_clken |= MISC_GPIO3ENB | MISC_GPIO4ENB; -#endif -#if defined(CONFIG_PL022_SPI) - periph1_clken |= MISC_SSP1ENB | MISC_SSP2ENB | MISC_SSP3ENB; -#endif - - writel(periph1_clken, &misc_p->periph1_clken); - - return 0; -} - -#ifdef CONFIG_DISPLAY_CPUINFO -int print_cpuinfo(void) -{ -#if defined(CONFIG_SPEAR600) - printf("CPU: SPEAr600\n"); -#else -#error CPU not supported in spear platform -#endif - return 0; -} -#endif - -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_ECC_BCH) && defined(CONFIG_NAND_FSMC) -static int do_switch_ecc(struct cmd_tbl *cmdtp, int flag, int argc, - char *const argv[]) -{ - if (argc != 2) - goto usage; - - if (strncmp(argv[1], "hw", 2) == 0) { - /* 1-bit HW ECC */ - printf("Switching to 1-bit HW ECC\n"); - fsmc_nand_switch_ecc(1); - } else if (strncmp(argv[1], "bch4", 2) == 0) { - /* 4-bit SW ECC BCH4 */ - printf("Switching to 4-bit SW ECC (BCH4)\n"); - fsmc_nand_switch_ecc(4); - } else { - goto usage; - } - - return 0; - -usage: - printf("Usage: nandecc %s\n", cmdtp->usage); - return 1; -} - -U_BOOT_CMD( - nandecc, 2, 0, do_switch_ecc, - "switch NAND ECC calculation algorithm", - "hw|bch4 - Switch between NAND hardware 1-bit HW and" - " 4-bit SW BCH\n" -); -#endif diff --git a/arch/arm/cpu/arm926ejs/spear/reset.c b/arch/arm/cpu/arm926ejs/spear/reset.c deleted file mode 100644 index 97a624e16c..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/reset.c +++ /dev/null @@ -1,39 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2009 - * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. - */ - -#include -#include -#include -#include -#include -#include - -void reset_cpu(void) -{ - struct syscntl_regs *syscntl_regs_p = - (struct syscntl_regs *)CONFIG_SPEAR_SYSCNTLBASE; - - printf("System is going to reboot ...\n"); - - /* - * This 1 second delay will allow the above message - * to be printed before reset - */ - udelay((1000 * 1000)); - - /* Going into slow mode before resetting SOC */ - writel(0x02, &syscntl_regs_p->scctrl); - - /* - * Writing any value to the system status register will - * reset the SoC - */ - writel(0x00, &syscntl_regs_p->scsysstat); - - /* system will restart */ - while (1) - ; -} diff --git a/arch/arm/cpu/arm926ejs/spear/spear600.c b/arch/arm/cpu/arm926ejs/spear/spear600.c deleted file mode 100644 index b31ede5eb9..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/spear600.c +++ /dev/null @@ -1,223 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2000-2009 - * Viresh Kumar, ST Microelectronics, viresh.kumar@st.com - * Vipin Kumar, ST Microelectronics, vipin.kumar@st.com - */ - -#include -#include -#include -#include -#include - -void spear_late_init(void) -{ - struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - - writel(0x80000007, &misc_p->arb_icm_ml1); - writel(0x80000007, &misc_p->arb_icm_ml2); - writel(0x80000007, &misc_p->arb_icm_ml3); - writel(0x80000007, &misc_p->arb_icm_ml4); - writel(0x80000007, &misc_p->arb_icm_ml5); - writel(0x80000007, &misc_p->arb_icm_ml6); - writel(0x80000007, &misc_p->arb_icm_ml7); - writel(0x80000007, &misc_p->arb_icm_ml8); - writel(0x80000007, &misc_p->arb_icm_ml9); -} - -static void sel_1v8(void) -{ - struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - u32 ddr1v8, ddr2v5; - - ddr2v5 = readl(&misc_p->ddr_2v5_compensation); - ddr2v5 &= 0x8080ffc0; - ddr2v5 |= 0x78000003; - writel(ddr2v5, &misc_p->ddr_2v5_compensation); - - ddr1v8 = readl(&misc_p->ddr_1v8_compensation); - ddr1v8 &= 0x8080ffc0; - ddr1v8 |= 0x78000010; - writel(ddr1v8, &misc_p->ddr_1v8_compensation); - - while (!(readl(&misc_p->ddr_1v8_compensation) & DDR_COMP_ACCURATE)) - ; -} - -static void sel_2v5(void) -{ - struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - u32 ddr1v8, ddr2v5; - - ddr1v8 = readl(&misc_p->ddr_1v8_compensation); - ddr1v8 &= 0x8080ffc0; - ddr1v8 |= 0x78000003; - writel(ddr1v8, &misc_p->ddr_1v8_compensation); - - ddr2v5 = readl(&misc_p->ddr_2v5_compensation); - ddr2v5 &= 0x8080ffc0; - ddr2v5 |= 0x78000010; - writel(ddr2v5, &misc_p->ddr_2v5_compensation); - - while (!(readl(&misc_p->ddr_2v5_compensation) & DDR_COMP_ACCURATE)) - ; -} - -/* - * plat_ddr_init: - */ -void plat_ddr_init(void) -{ - struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - u32 ddrpad; - u32 core3v3, ddr1v8, ddr2v5; - - /* DDR pad register configurations */ - ddrpad = readl(&misc_p->ddr_pad); - ddrpad &= ~DDR_PAD_CNF_MSK; - -#if (CONFIG_DDR_HCLK) - ddrpad |= 0xEAAB; -#elif (CONFIG_DDR_2HCLK) - ddrpad |= 0xEAAD; -#elif (CONFIG_DDR_PLL2) - ddrpad |= 0xEAAD; -#endif - writel(ddrpad, &misc_p->ddr_pad); - - /* Compensation register configurations */ - core3v3 = readl(&misc_p->core_3v3_compensation); - core3v3 &= 0x8080ffe0; - core3v3 |= 0x78000002; - writel(core3v3, &misc_p->core_3v3_compensation); - - ddr1v8 = readl(&misc_p->ddr_1v8_compensation); - ddr1v8 &= 0x8080ffc0; - ddr1v8 |= 0x78000004; - writel(ddr1v8, &misc_p->ddr_1v8_compensation); - - ddr2v5 = readl(&misc_p->ddr_2v5_compensation); - ddr2v5 &= 0x8080ffc0; - ddr2v5 |= 0x78000004; - writel(ddr2v5, &misc_p->ddr_2v5_compensation); - - if ((readl(&misc_p->ddr_pad) & DDR_PAD_SW_CONF) == DDR_PAD_SW_CONF) { - /* Software memory configuration */ - if (readl(&misc_p->ddr_pad) & DDR_PAD_SSTL_SEL) - sel_1v8(); - else - sel_2v5(); - } else { - /* Hardware memory configuration */ - if (readl(&misc_p->ddr_pad) & DDR_PAD_DRAM_TYPE) - sel_1v8(); - else - sel_2v5(); - } -} - -/* - * xxx_boot_selected: - * - * return true if the particular booting option is selected - * return false otherwise - */ -static u32 read_bootstrap(void) -{ - return (readl(CONFIG_SPEAR_BOOTSTRAPCFG) >> CONFIG_SPEAR_BOOTSTRAPSHFT) - & CONFIG_SPEAR_BOOTSTRAPMASK; -} - -int snor_boot_selected(void) -{ - u32 bootstrap = read_bootstrap(); - - if (SNOR_BOOT_SUPPORTED) { - /* Check whether SNOR boot is selected */ - if ((bootstrap & CONFIG_SPEAR_ONLYSNORBOOT) == - CONFIG_SPEAR_ONLYSNORBOOT) - return true; - - if ((bootstrap & CONFIG_SPEAR_NORNANDBOOT) == - CONFIG_SPEAR_NORNAND8BOOT) - return true; - - if ((bootstrap & CONFIG_SPEAR_NORNANDBOOT) == - CONFIG_SPEAR_NORNAND16BOOT) - return true; - } - - return false; -} - -int nand_boot_selected(void) -{ - u32 bootstrap = read_bootstrap(); - - if (NAND_BOOT_SUPPORTED) { - /* Check whether NAND boot is selected */ - if ((bootstrap & CONFIG_SPEAR_NORNANDBOOT) == - CONFIG_SPEAR_NORNAND8BOOT) - return true; - - if ((bootstrap & CONFIG_SPEAR_NORNANDBOOT) == - CONFIG_SPEAR_NORNAND16BOOT) - return true; - } - - return false; -} - -int pnor_boot_selected(void) -{ - /* Parallel NOR boot is not selected in any SPEAr600 revision */ - return false; -} - -int usb_boot_selected(void) -{ - u32 bootstrap = read_bootstrap(); - - if (USB_BOOT_SUPPORTED) { - /* Check whether USB boot is selected */ - if (!(bootstrap & CONFIG_SPEAR_USBBOOT)) - return true; - } - - return false; -} - -int tftp_boot_selected(void) -{ - /* TFTP boot is not selected in any SPEAr600 revision */ - return false; -} - -int uart_boot_selected(void) -{ - /* UART boot is not selected in any SPEAr600 revision */ - return false; -} - -int spi_boot_selected(void) -{ - /* SPI boot is not selected in any SPEAr600 revision */ - return false; -} - -int i2c_boot_selected(void) -{ - /* I2C boot is not selected in any SPEAr600 revision */ - return false; -} - -int mmc_boot_selected(void) -{ - return false; -} - -void plat_late_init(void) -{ - spear_late_init(); -} diff --git a/arch/arm/cpu/arm926ejs/spear/spl.c b/arch/arm/cpu/arm926ejs/spear/spl.c deleted file mode 100644 index 693cee1ab3..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/spl.c +++ /dev/null @@ -1,296 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2011 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * Copyright (C) 2012 Stefan Roese - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -/* Reserve some space to store the BootROM's stack pointer during SPL operation. - * The BSS cannot be used for this purpose because it will be zeroed after - * having stored the pointer, so force the location to the data section. - */ -u32 bootrom_stash_sp __section(".data"); - -static void ddr_clock_init(void) -{ - struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - u32 clkenb, ddrpll; - - clkenb = readl(&misc_p->periph1_clken); - clkenb &= ~PERIPH_MPMCMSK; - clkenb |= PERIPH_MPMC_WE; - - /* Intentionally done twice */ - writel(clkenb, &misc_p->periph1_clken); - writel(clkenb, &misc_p->periph1_clken); - - ddrpll = readl(&misc_p->pll_ctr_reg); - ddrpll &= ~MEM_CLK_SEL_MSK; -#if (CONFIG_DDR_HCLK) - ddrpll |= MEM_CLK_HCLK; -#elif (CONFIG_DDR_2HCLK) - ddrpll |= MEM_CLK_2HCLK; -#elif (CONFIG_DDR_PLL2) - ddrpll |= MEM_CLK_PLL2; -#else -#error "please define one of CONFIG_DDR_(HCLK|2HCLK|PLL2)" -#endif - writel(ddrpll, &misc_p->pll_ctr_reg); - - writel(readl(&misc_p->periph1_clken) | PERIPH_MPMC_EN, - &misc_p->periph1_clken); -} - -static void mpmc_init_values(void) -{ - u32 i; - u32 *mpmc_reg_p = (u32 *)CONFIG_SPEAR_MPMCBASE; - u32 *mpmc_val_p = &mpmc_conf_vals[0]; - - for (i = 0; i < CONFIG_SPEAR_MPMCREGS; i++, mpmc_reg_p++, mpmc_val_p++) - writel(*mpmc_val_p, mpmc_reg_p); - - mpmc_reg_p = (u32 *)CONFIG_SPEAR_MPMCBASE; - - /* - * MPMC controller start - * MPMC waiting for DLLLOCKREG high - */ - writel(0x01000100, &mpmc_reg_p[7]); - - while (!(readl(&mpmc_reg_p[3]) & 0x10000)) - ; -} - -static void mpmc_init(void) -{ - /* Clock related settings for DDR */ - ddr_clock_init(); - - /* - * DDR pad register bits are different for different SoCs - * Compensation values are also handled separately - */ - plat_ddr_init(); - - /* Initialize mpmc register values */ - mpmc_init_values(); -} - -static void pll_init(void) -{ - struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - - /* Initialize PLLs */ - writel(FREQ_332, &misc_p->pll1_frq); - writel(0x1C0A, &misc_p->pll1_cntl); - writel(0x1C0E, &misc_p->pll1_cntl); - writel(0x1C06, &misc_p->pll1_cntl); - writel(0x1C0E, &misc_p->pll1_cntl); - - writel(FREQ_332, &misc_p->pll2_frq); - writel(0x1C0A, &misc_p->pll2_cntl); - writel(0x1C0E, &misc_p->pll2_cntl); - writel(0x1C06, &misc_p->pll2_cntl); - writel(0x1C0E, &misc_p->pll2_cntl); - - /* wait for pll locks */ - while (!(readl(&misc_p->pll1_cntl) & 0x1)) - ; - while (!(readl(&misc_p->pll2_cntl) & 0x1)) - ; -} - -static void mac_init(void) -{ - struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - - writel(readl(&misc_p->periph1_clken) & (~PERIPH_GMAC), - &misc_p->periph1_clken); - - writel(SYNTH23, &misc_p->gmac_synth_clk); - - switch (get_socrev()) { - case SOC_SPEAR600_AA: - case SOC_SPEAR600_AB: - case SOC_SPEAR600_BA: - case SOC_SPEAR600_BB: - case SOC_SPEAR600_BC: - case SOC_SPEAR600_BD: - writel(0x0, &misc_p->gmac_ctr_reg); - break; - - case SOC_SPEAR300: - case SOC_SPEAR310: - case SOC_SPEAR320: - writel(0x4, &misc_p->gmac_ctr_reg); - break; - } - - writel(readl(&misc_p->periph1_clken) | PERIPH_GMAC, - &misc_p->periph1_clken); - - writel(readl(&misc_p->periph1_rst) | PERIPH_GMAC, - &misc_p->periph1_rst); - writel(readl(&misc_p->periph1_rst) & (~PERIPH_GMAC), - &misc_p->periph1_rst); -} - -static void sys_init(void) -{ - struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - struct syscntl_regs *syscntl_p = - (struct syscntl_regs *)CONFIG_SPEAR_SYSCNTLBASE; - - /* Set system state to SLOW */ - writel(SLOW, &syscntl_p->scctrl); - writel(PLL_TIM << 3, &syscntl_p->scpllctrl); - - /* Initialize PLLs */ - pll_init(); - - /* - * Ethernet configuration - * To be done only if the tftp boot is not selected already - * Boot code ensures the correct configuration in tftp booting - */ - if (!tftp_boot_selected()) - mac_init(); - - writel(RTC_DISABLE | PLLTIMEEN, &misc_p->periph_clk_cfg); - writel(0x555, &misc_p->amba_clk_cfg); - - writel(NORMAL, &syscntl_p->scctrl); - - /* Wait for system to switch to normal mode */ - while (((readl(&syscntl_p->scctrl) >> MODE_SHIFT) & MODE_MASK) - != NORMAL) - ; -} - -/* - * get_socrev - * - * Get SoC Revision. - * @return SOC_SPEARXXX - */ -int get_socrev(void) -{ -#if defined(CONFIG_SPEAR600) - struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - u32 soc_id = readl(&misc_p->soc_core_id); - u32 pri_socid = (soc_id >> SOC_PRI_SHFT) & 0xFF; - u32 sec_socid = (soc_id >> SOC_SEC_SHFT) & 0xFF; - - if ((pri_socid == 'B') && (sec_socid == 'B')) - return SOC_SPEAR600_BB; - else if ((pri_socid == 'B') && (sec_socid == 'C')) - return SOC_SPEAR600_BC; - else if ((pri_socid == 'B') && (sec_socid == 'D')) - return SOC_SPEAR600_BD; - else if (soc_id == 0) - return SOC_SPEAR600_BA; - else - return SOC_SPEAR_NA; -#endif -} - -/* - * SNOR (Serial NOR flash) related functions - */ -static void snor_init(void) -{ - struct smi_regs *const smicntl = - (struct smi_regs * const)CONFIG_SYS_SMI_BASE; - - /* Setting the fast mode values. SMI working at 166/4 = 41.5 MHz */ - writel(HOLD1 | FAST_MODE | BANK_EN | DSEL_TIME | PRESCAL4, - &smicntl->smi_cr1); -} - -u32 spl_boot_device(void) -{ - u32 mode = 0; - - if (usb_boot_selected()) { - mode = BOOT_DEVICE_BOOTROM; - } else if (snor_boot_selected()) { - /* SNOR-SMI initialization */ - snor_init(); - - mode = BOOT_DEVICE_NOR; - } - - return mode; -} - -void board_boot_order(u32 *spl_boot_list) -{ - spl_boot_list[0] = spl_boot_device(); - - /* - * If the main boot device (eg. NOR) is empty, try to jump back into the - * BootROM for USB boot process. - */ - if (USB_BOOT_SUPPORTED) - spl_boot_list[1] = BOOT_DEVICE_BOOTROM; -} - -void board_init_f(ulong dummy) -{ - struct misc_regs *misc_p = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - - /* Initialize PLLs */ - sys_init(); - - preloader_console_init(); - arch_cpu_init(); - - /* Enable IPs (release reset) */ - writel(PERIPH_RST_ALL, &misc_p->periph1_rst); - - /* Initialize MPMC */ - puts("Configure DDR\n"); - mpmc_init(); - spear_late_init(); -} - -/* - * In a few cases (Ethernet, UART or USB boot, we might want to go back into the - * BootROM code right after having initialized a few components like the DRAM). - * The following function is called from SPL common code (board_init_r). - */ -int board_return_to_bootrom(struct spl_image_info *spl_image, - struct spl_boot_device *bootdev) -{ - /* - * Retrieve the BootROM's stack pointer and jump back to the start of - * the SPL, where we can easily branch back into the BootROM. Don't do - * it right here because SPL might be compiled in Thumb mode while the - * BootROM expects ARM mode. - */ - asm volatile ("ldr r0, =bootrom_stash_sp;" - "ldr r0, [r0];" - "mov sp, r0;" -#if defined(CONFIG_SPL_SYS_THUMB_BUILD) - "blx back_to_bootrom;" -#else - "bl back_to_bootrom;" -#endif - ); - - return 0; -} diff --git a/arch/arm/cpu/arm926ejs/spear/spr600_mt47h128m8_3_266_cl5_async.c b/arch/arm/cpu/arm926ejs/spear/spr600_mt47h128m8_3_266_cl5_async.c deleted file mode 100644 index 79ab2a70dc..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/spr600_mt47h128m8_3_266_cl5_async.c +++ /dev/null @@ -1,113 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2000-2009 - * Vipin Kumar, ST Microelectronics, vipin.kumar@st.com - */ - -#include - -#if (CONFIG_DDR_PLL2) - -const u32 mpmc_conf_vals[CONFIG_SPEAR_MPMCREGS] = { - 0x00000001, - 0x00000000, - 0x01000000, - 0x00000101, - 0x00000001, - 0x01000000, - 0x00010001, - 0x00000100, - 0x00010001, - 0x00000003, - 0x01000201, - 0x06000202, - 0x06060106, - 0x03050502, - 0x03040404, - 0x02020503, - 0x02010106, - 0x03000404, - 0x02030202, - 0x03000204, - 0x0707073f, - 0x07070707, - 0x06060607, - 0x06060606, - 0x05050506, - 0x05050505, - 0x04040405, - 0x04040404, - 0x03030304, - 0x03030303, - 0x02020203, - 0x02020202, - 0x01010102, - 0x01010101, - 0x08080a01, - 0x0000023f, - 0x00040800, - 0x00000000, - 0x00000f02, - 0x00001b1b, - 0x7f000000, - 0x005f0000, - 0x1c040b6a, - 0x00640064, - 0x00640064, - 0x00640064, - 0x00000064, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x000007ff, - 0x00000000, - 0x47ec00c8, - 0x00c8001f, - 0x00000000, - 0x0000cd98, - 0x00000000, - 0x03030100, - 0x03030303, - 0x03030303, - 0x03030303, - 0x00270000, - 0x00250027, - 0x00300000, - 0x008900b7, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x00000000, - 0x00000000, - 0x00000000 -}; -#endif diff --git a/arch/arm/cpu/arm926ejs/spear/spr600_mt47h32m16_333_cl5_psync.c b/arch/arm/cpu/arm926ejs/spear/spr600_mt47h32m16_333_cl5_psync.c deleted file mode 100644 index 121b636077..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/spr600_mt47h32m16_333_cl5_psync.c +++ /dev/null @@ -1,118 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2000-2009 - * Vipin Kumar, ST Microelectronics, vipin.kumar@st.com - */ - -#include - -#if (CONFIG_DDR_PLL2 || CONFIG_DDR_2HCLK) - -const u32 mpmc_conf_vals[CONFIG_SPEAR_MPMCREGS] = { -#if (CONFIG_DDR_PLL2) - 0x00000001, - 0x00000000, -#elif (CONFIG_DDR_2HCLK) - 0x02020201, - 0x02020202, -#endif - 0x01000000, - 0x00000101, - 0x00000101, - 0x01000000, - 0x00010001, - 0x00000100, - 0x01010001, - 0x00000201, - 0x01000101, - 0x06000002, - 0x06060106, - 0x03050502, - 0x03040404, - 0x02020503, - 0x02010106, - 0x03000405, - 0x03040202, - 0x04000305, - 0x0707073f, - 0x07070707, - 0x06060607, - 0x06060606, - 0x05050506, - 0x05050505, - 0x04040405, - 0x04040404, - 0x03030304, - 0x03030303, - 0x02020203, - 0x02020202, - 0x01010102, - 0x01010101, - 0x0a0a0a01, - 0x0000023f, - 0x00050a00, - 0x11000000, - 0x00001302, - 0x00000A0A, - 0x72000000, - 0x00550000, - 0x2b050e86, - 0x00640064, - 0x00640064, - 0x00640064, - 0x00000064, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00000a24, - 0x43C20000, - 0x5b1c00c8, - 0x00c8002e, - 0x00000000, - 0x0001046b, - 0x00000000, - 0x03030100, - 0x03030303, - 0x03030303, - 0x03030303, - 0x00210000, - 0x00010021, - 0x00200000, - 0x006c0090, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x00000000, - 0x00000000, - 0x00000000 -}; -#endif diff --git a/arch/arm/cpu/arm926ejs/spear/spr600_mt47h32m16_37e_166_cl4_sync.c b/arch/arm/cpu/arm926ejs/spear/spr600_mt47h32m16_37e_166_cl4_sync.c deleted file mode 100644 index 64c8bab9bf..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/spr600_mt47h32m16_37e_166_cl4_sync.c +++ /dev/null @@ -1,113 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2000-2009 - * Vipin Kumar, ST Microelectronics, vipin.kumar@st.com - */ - -#include - -#if (CONFIG_DDR_HCLK) - -const u32 mpmc_conf_vals[CONFIG_SPEAR_MPMCREGS] = { - 0x03030301, - 0x03030303, - 0x01000000, - 0x00000101, - 0x00000001, - 0x01000000, - 0x00010001, - 0x00000100, - 0x00010001, - 0x00000003, - 0x01000201, - 0x06000202, - 0x06060106, - 0x03050502, - 0x03040404, - 0x02020503, - 0x02010106, - 0x03000404, - 0x02020202, - 0x03000203, - 0x0707073f, - 0x07070707, - 0x06060607, - 0x06060606, - 0x05050506, - 0x05050505, - 0x04040405, - 0x04040404, - 0x03030304, - 0x03030303, - 0x02020203, - 0x02020202, - 0x01010102, - 0x01010101, - 0x08080a01, - 0x0000023f, - 0x00030600, - 0x00000000, - 0x00000a02, - 0x00001c1c, - 0x7f000000, - 0x005f0000, - 0x12030743, - 0x00640064, - 0x00640064, - 0x00640064, - 0x00000064, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x0000050e, - 0x00000000, - 0x2d8900c8, - 0x00c80014, - 0x00000000, - 0x00008236, - 0x00000000, - 0x03030100, - 0x03030303, - 0x03030303, - 0x03030303, - 0x00400000, - 0x003a0040, - 0x00680000, - 0x00d80120, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x00000000, - 0x00000000, - 0x00000000 -}; -#endif diff --git a/arch/arm/cpu/arm926ejs/spear/spr600_mt47h64m16_3_333_cl5_psync.c b/arch/arm/cpu/arm926ejs/spear/spr600_mt47h64m16_3_333_cl5_psync.c deleted file mode 100644 index 87654663fc..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/spr600_mt47h64m16_3_333_cl5_psync.c +++ /dev/null @@ -1,127 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2000-2009 - * Vipin Kumar, ST Microelectronics, vipin.kumar@st.com - */ - -#include - -#if (CONFIG_DDR_PLL2 || CONFIG_DDR_2HCLK) - -const u32 mpmc_conf_vals[CONFIG_SPEAR_MPMCREGS] = { -#if (CONFIG_DDR_PLL2) - 0x00000001, - 0x00000000, -#elif (CONFIG_DDR_2HCLK) - 0x02020201, - 0x02020202, -#endif - 0x01000000, - 0x00000101, - 0x00000101, - 0x01000000, - 0x00010001, - 0x00000100, - 0x01010001, - 0x00000201, - 0x01000101, - 0x06000002, - 0x06060106, - 0x03050502, - 0x03040404, - 0x02020503, -#ifdef CONFIG_X600 - 0x02030206, -#else - 0x02010106, -#endif - 0x03000405, - 0x03040202, - 0x04000305, - 0x0707073f, - 0x07070707, - 0x06060607, - 0x06060606, - 0x05050506, - 0x05050505, - 0x04040405, - 0x04040404, - 0x03030304, - 0x03030303, - 0x02020203, - 0x02020202, - 0x01010102, - 0x01010101, - 0x0a0a0a01, - 0x0000023f, - 0x00050a00, - 0x11000000, - 0x00001302, - 0x00000A0A, -#ifdef CONFIG_X600 - 0x7f000000, - 0x005c0000, -#else - 0x72000000, - 0x00550000, -#endif - 0x2b050e86, - 0x00640064, - 0x00640064, - 0x00640064, - 0x00000064, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00200020, - 0x00000a24, - 0x43C20000, - 0x5b1c00c8, - 0x00c8002e, - 0x00000000, - 0x0001046b, - 0x00000000, - 0x03030100, - 0x03030303, - 0x03030303, - 0x03030303, - 0x00210000, - 0x00010021, - 0x00200000, - 0x006c0090, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x003fffff, - 0x003fffff, - 0x00000000, - 0x00000000, - 0x00000000, - 0x00000000, - 0x00000000 -}; -#endif diff --git a/arch/arm/cpu/arm926ejs/spear/spr_lowlevel_init.S b/arch/arm/cpu/arm926ejs/spear/spr_lowlevel_init.S deleted file mode 100644 index 417e87a7b5..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/spr_lowlevel_init.S +++ /dev/null @@ -1,173 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2006 - * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. - */ - -#include - -/* - * platform specific initializations are already done in Xloader - * Initializations already done include - * DDR, PLLs, IP's clock enable and reset release etc - */ -.globl lowlevel_init -lowlevel_init: - mov pc, lr - -/* void setfreq(unsigned int device, unsigned int frequency) */ -.global setfreq -setfreq: - stmfd sp!,{r14} - stmfd sp!,{r0-r12} - - mov r8,sp - ldr sp,SRAM_STACK_V - - /* Saving the function arguements for later use */ - mov r4,r0 - mov r5,r1 - - /* Putting DDR into self refresh */ - ldr r0,DDR_07_V - ldr r1,[r0] - ldr r2,DDR_ACTIVE_V - bic r1, r1, r2 - str r1,[r0] - ldr r0,DDR_57_V - ldr r1,[r0] - ldr r2,CYCLES_MASK_V - bic r1, r1, r2 - ldr r2,REFRESH_CYCLES_V - orr r1, r1, r2, lsl #16 - str r1,[r0] - ldr r0,DDR_07_V - ldr r1,[r0] - ldr r2,SREFRESH_MASK_V - orr r1, r1, r2 - str r1,[r0] - - /* flush pipeline */ - b flush - .align 5 -flush: - /* Delay to ensure self refresh mode */ - ldr r0,SREFRESH_DELAY_V -delay: - sub r0,r0,#1 - cmp r0,#0 - bne delay - - /* Putting system in slow mode */ - ldr r0,SCCTRL_V - mov r1,#2 - str r1,[r0] - - /* Changing PLL(1/2) frequency */ - mov r0,r4 - mov r1,r5 - - cmp r4,#0 - beq pll1_freq - - /* Change PLL2 (DDR frequency) */ - ldr r6,PLL2_FREQ_V - ldr r7,PLL2_CNTL_V - b pll2_freq - -pll1_freq: - /* Change PLL1 (CPU frequency) */ - ldr r6,PLL1_FREQ_V - ldr r7,PLL1_CNTL_V - -pll2_freq: - mov r0,r6 - ldr r1,[r0] - ldr r2,PLLFREQ_MASK_V - bic r1,r1,r2 - mov r2,r5,lsr#1 - orr r1,r1,r2,lsl#24 - str r1,[r0] - - mov r0,r7 - ldr r1,P1C0A_V - str r1,[r0] - ldr r1,P1C0E_V - str r1,[r0] - ldr r1,P1C06_V - str r1,[r0] - ldr r1,P1C0E_V - str r1,[r0] - -lock: - ldr r1,[r0] - and r1,r1,#1 - cmp r1,#0 - beq lock - - /* Putting system back to normal mode */ - ldr r0,SCCTRL_V - mov r1,#4 - str r1,[r0] - - /* Putting DDR back to normal */ - ldr r0,DDR_07_V - ldr r1,[R0] - ldr r2,SREFRESH_MASK_V - bic r1, r1, r2 - str r1,[r0] - ldr r2,DDR_ACTIVE_V - orr r1, r1, r2 - str r1,[r0] - - /* Delay to ensure self refresh mode */ - ldr r0,SREFRESH_DELAY_V -1: - sub r0,r0,#1 - cmp r0,#0 - bne 1b - - mov sp,r8 - /* Resuming back to code */ - ldmia sp!,{r0-r12} - ldmia sp!,{pc} - -SCCTRL_V: - .word 0xfca00000 -PLL1_FREQ_V: - .word 0xfca8000C -PLL1_CNTL_V: - .word 0xfca80008 -PLL2_FREQ_V: - .word 0xfca80018 -PLL2_CNTL_V: - .word 0xfca80014 -PLLFREQ_MASK_V: - .word 0xff000000 -P1C0A_V: - .word 0x1C0A -P1C0E_V: - .word 0x1C0E -P1C06_V: - .word 0x1C06 - -SREFRESH_DELAY_V: - .word 0x9999 -SRAM_STACK_V: - .word 0xD2800600 -DDR_07_V: - .word 0xfc60001c -DDR_ACTIVE_V: - .word 0x01000000 -DDR_57_V: - .word 0xfc6000e4 -CYCLES_MASK_V: - .word 0xffff0000 -REFRESH_CYCLES_V: - .word 0xf0f0 -SREFRESH_MASK_V: - .word 0x00010000 - -.global setfreq_sz -setfreq_sz: - .word setfreq_sz - setfreq diff --git a/arch/arm/cpu/arm926ejs/spear/spr_misc.c b/arch/arm/cpu/arm926ejs/spear/spr_misc.c deleted file mode 100644 index 044052b32f..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/spr_misc.c +++ /dev/null @@ -1,253 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2009 - * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#define CPU 0 -#define DDR 1 -#define SRAM_REL 0xD2801000 - -DECLARE_GLOBAL_DATA_PTR; - -#if defined(CONFIG_CMD_NET) -static int i2c_read_mac(uchar *buffer); -#endif - -int dram_init(void) -{ - /* Store complete RAM size and return */ - gd->ram_size = get_ram_size(PHYS_SDRAM_1, PHYS_SDRAM_1_MAXSIZE); - - return 0; -} - -int dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = gd->ram_size; - - return 0; -} - -int board_early_init_f() -{ -#if defined(CONFIG_ST_SMI) - smi_init(); -#endif - return 0; -} -int misc_init_r(void) -{ -#if defined(CONFIG_CMD_NET) - uchar mac_id[6]; - - if (!eth_env_get_enetaddr("ethaddr", mac_id) && !i2c_read_mac(mac_id)) - eth_env_set_enetaddr("ethaddr", mac_id); -#endif - env_set("verify", "n"); - -#if defined(CONFIG_SPEAR_USBTTY) - env_set("stdin", "usbtty"); - env_set("stdout", "usbtty"); - env_set("stderr", "usbtty"); - -#ifndef CONFIG_SYS_NO_DCACHE - dcache_enable(); -#endif -#endif - return 0; -} - -#ifdef CONFIG_SPEAR_EMI -struct cust_emi_para { - unsigned int tap; - unsigned int tsdp; - unsigned int tdpw; - unsigned int tdpr; - unsigned int tdcs; -}; - -/* EMI timing setting of m28w640hc of linux kernel */ -const struct cust_emi_para emi_timing_m28w640hc = { - .tap = 0x10, - .tsdp = 0x05, - .tdpw = 0x0a, - .tdpr = 0x0a, - .tdcs = 0x05, -}; - -/* EMI timing setting of bootrom */ -const struct cust_emi_para emi_timing_bootrom = { - .tap = 0xf, - .tsdp = 0x0, - .tdpw = 0xff, - .tdpr = 0x111, - .tdcs = 0x02, -}; - -void spear_emi_init(void) -{ - const struct cust_emi_para *p = &emi_timing_m28w640hc; - struct emi_regs *emi_regs_p = (struct emi_regs *)CONFIG_SPEAR_EMIBASE; - unsigned int cs; - unsigned int val, tmp; - - val = readl(CONFIG_SPEAR_RASBASE); - - if (val & EMI_ACKMSK) - tmp = 0x3f; - else - tmp = 0x0; - - writel(tmp, &emi_regs_p->ack); - - for (cs = 0; cs < CONFIG_SYS_MAX_FLASH_BANKS; cs++) { - writel(p->tap, &emi_regs_p->bank_regs[cs].tap); - writel(p->tsdp, &emi_regs_p->bank_regs[cs].tsdp); - writel(p->tdpw, &emi_regs_p->bank_regs[cs].tdpw); - writel(p->tdpr, &emi_regs_p->bank_regs[cs].tdpr); - writel(p->tdcs, &emi_regs_p->bank_regs[cs].tdcs); - writel(EMI_CNTL_ENBBYTERW | ((val & 0x18) >> 3), - &emi_regs_p->bank_regs[cs].control); - } -} -#endif - -int spear_board_init(ulong mach_type) -{ - gd->bd->bi_arch_number = mach_type; - - /* adress of boot parameters */ - gd->bd->bi_boot_params = CONFIG_BOOT_PARAMS_ADDR; - -#ifdef CONFIG_SPEAR_EMI - spear_emi_init(); -#endif - return 0; -} - -#if defined(CONFIG_CMD_NET) -static int i2c_read_mac(uchar *buffer) -{ - u8 buf[2]; - - i2c_read(CONFIG_I2C_CHIPADDRESS, MAGIC_OFF, 1, buf, MAGIC_LEN); - - /* Check if mac in i2c memory is valid */ - if ((buf[0] == MAGIC_BYTE0) && (buf[1] == MAGIC_BYTE1)) { - /* Valid mac address is saved in i2c eeprom */ - i2c_read(CONFIG_I2C_CHIPADDRESS, MAC_OFF, 1, buffer, MAC_LEN); - return 0; - } - - return -1; -} - -static int write_mac(uchar *mac) -{ - u8 buf[2]; - - buf[0] = (u8)MAGIC_BYTE0; - buf[1] = (u8)MAGIC_BYTE1; - i2c_write(CONFIG_I2C_CHIPADDRESS, MAGIC_OFF, 1, buf, MAGIC_LEN); - - buf[0] = (u8)~MAGIC_BYTE0; - buf[1] = (u8)~MAGIC_BYTE1; - - i2c_read(CONFIG_I2C_CHIPADDRESS, MAGIC_OFF, 1, buf, MAGIC_LEN); - - /* check if valid MAC address is saved in I2C EEPROM or not? */ - if ((buf[0] == MAGIC_BYTE0) && (buf[1] == MAGIC_BYTE1)) { - i2c_write(CONFIG_I2C_CHIPADDRESS, MAC_OFF, 1, mac, MAC_LEN); - puts("I2C EEPROM written with mac address \n"); - return 0; - } - - puts("I2C EEPROM writing failed\n"); - return -1; -} -#endif - -int do_chip_config(struct cmd_tbl *cmdtp, int flag, int argc, - char *const argv[]) -{ - void (*sram_setfreq) (unsigned int, unsigned int); - unsigned int frequency; -#if defined(CONFIG_CMD_NET) - unsigned char mac[6]; -#endif - - if ((argc > 3) || (argc < 2)) - return cmd_usage(cmdtp); - - if ((!strcmp(argv[1], "cpufreq")) || (!strcmp(argv[1], "ddrfreq"))) { - - frequency = simple_strtoul(argv[2], NULL, 0); - - if (frequency > 333) { - printf("Frequency is limited to 333MHz\n"); - return 1; - } - - sram_setfreq = memcpy((void *)SRAM_REL, setfreq, setfreq_sz); - - if (!strcmp(argv[1], "cpufreq")) { - sram_setfreq(CPU, frequency); - printf("CPU frequency changed to %u\n", frequency); - } else { - sram_setfreq(DDR, frequency); - printf("DDR frequency changed to %u\n", frequency); - } - - return 0; - -#if defined(CONFIG_CMD_NET) - } else if (!strcmp(argv[1], "ethaddr")) { - - u32 reg; - char *e, *s = argv[2]; - for (reg = 0; reg < 6; ++reg) { - mac[reg] = s ? simple_strtoul(s, &e, 16) : 0; - if (s) - s = (*e) ? e + 1 : e; - } - write_mac(mac); - - return 0; -#endif - } else if (!strcmp(argv[1], "print")) { -#if defined(CONFIG_CMD_NET) - if (!i2c_read_mac(mac)) { - printf("Ethaddr (from i2c mem) = %pM\n", mac); - } else { - printf("Ethaddr (from i2c mem) = Not set\n"); - } -#endif - return 0; - } - - return cmd_usage(cmdtp); -} - -U_BOOT_CMD(chip_config, 3, 1, do_chip_config, - "configure chip", - "chip_config cpufreq/ddrfreq frequency\n" -#if defined(CONFIG_CMD_NET) - "chip_config ethaddr XX:XX:XX:XX:XX:XX\n" -#endif - "chip_config print"); diff --git a/arch/arm/cpu/arm926ejs/spear/start.S b/arch/arm/cpu/arm926ejs/spear/start.S deleted file mode 100644 index 9ac96291b7..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/start.S +++ /dev/null @@ -1,65 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * armboot - Startup Code for ARM926EJS CPU-core - * - * Copyright (c) 2003 Texas Instruments - * - * ----- Adapted for OMAP1610 OMAP730 from ARM925t code ------ - * - * Copyright (c) 2001 Marius Gröger - * Copyright (c) 2002 Alex Züpke - * Copyright (c) 2002 Gary Jennejohn - * Copyright (c) 2003 Richard Woodruff - * Copyright (c) 2003 Kshitij - */ - - -#include - -/* - ************************************************************************* - * - * Startup Code (reset vector) - * - * The BootROM already initialized its own stack in the [0-0xb00] reserved - * range of the SRAM. The SPL (in _main) will update the stack pointer to - * its own SRAM area (right before the gd section). - * - ************************************************************************* - */ - - .globl reset - .globl back_to_bootrom - -reset: - /* - * SPL has to return back to BootROM in a few cases (eg. Ethernet boot, - * UART boot, USB boot): save registers in BootROM's stack and then the - * BootROM's stack pointer in the SPL's data section. - */ - push {r0-r12,lr} - ldr r0, =bootrom_stash_sp - str sp, [r0] - - /* - * Flush v4 I/D caches - */ - mov r0, #0 - mcr p15, 0, r0, c7, c7, 0 /* Flush v3/v4 cache */ - mcr p15, 0, r0, c8, c7, 0 /* Flush v4 TLB */ - - /* - * Enable instruction cache - */ - mrc p15, 0, r0, c1, c0, 0 - orr r0, r0, #0x00001000 /* set bit 12 (I) I-Cache */ - mcr p15, 0, r0, c1, c0, 0 - - /* - * Go setup Memory and board specific bits prior to relocation. - * This call is not supposed to return. - */ - b _main /* _main will call board_init_f */ - -back_to_bootrom: - pop {r0-r12,pc} diff --git a/arch/arm/cpu/arm926ejs/spear/timer.c b/arch/arm/cpu/arm926ejs/spear/timer.c deleted file mode 100644 index d5f6cccaae..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/timer.c +++ /dev/null @@ -1,121 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2009 - * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#define GPT_RESOLUTION (CONFIG_SPEAR_HZ_CLOCK / CONFIG_SPEAR_HZ) -#define READ_TIMER() (readl(&gpt_regs_p->count) & GPT_FREE_RUNNING) - -static struct gpt_regs *const gpt_regs_p = - (struct gpt_regs *)CONFIG_SPEAR_TIMERBASE; - -static struct misc_regs *const misc_regs_p = - (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - -DECLARE_GLOBAL_DATA_PTR; - -static ulong get_timer_masked(void); - -#define timestamp gd->arch.tbl -#define lastdec gd->arch.lastinc - -int timer_init(void) -{ - u32 synth; - - /* Prescaler setting */ -#if defined(CONFIG_SPEAR600) - writel(MISC_PRSC_CFG, &misc_regs_p->prsc1_clk_cfg); - synth = MISC_GPT3SYNTH; -#else -# error Incorrect config. Can only be SPEAR{600|300|310|320} -#endif - - writel(readl(&misc_regs_p->periph_clk_cfg) | synth, - &misc_regs_p->periph_clk_cfg); - - /* disable timers */ - writel(GPT_PRESCALER_1 | GPT_MODE_AUTO_RELOAD, &gpt_regs_p->control); - - /* load value for free running */ - writel(GPT_FREE_RUNNING, &gpt_regs_p->compare); - - /* auto reload, start timer */ - writel(readl(&gpt_regs_p->control) | GPT_ENABLE, &gpt_regs_p->control); - - /* Reset the timer */ - lastdec = READ_TIMER(); - timestamp = 0; - - return 0; -} - -/* - * timer without interrupts - */ -ulong get_timer(ulong base) -{ - return (get_timer_masked() / GPT_RESOLUTION) - base; -} - -void __udelay(unsigned long usec) -{ - ulong tmo; - ulong start = get_timer_masked(); - ulong tenudelcnt = CONFIG_SPEAR_HZ_CLOCK / (1000 * 100); - ulong rndoff; - - rndoff = (usec % 10) ? 1 : 0; - - /* tenudelcnt timer tick gives 10 microsecconds delay */ - tmo = ((usec / 10) + rndoff) * tenudelcnt; - - while ((ulong) (get_timer_masked() - start) < tmo) - ; -} - -static ulong get_timer_masked(void) -{ - ulong now = READ_TIMER(); - - if (now >= lastdec) { - /* normal mode */ - timestamp += now - lastdec; - } else { - /* we have an overflow ... */ - timestamp += now + GPT_FREE_RUNNING - lastdec; - } - lastdec = now; - - return timestamp; -} - -/* - * This function is derived from PowerPC code (read timebase as long long). - * On ARM it just returns the timer value. - */ -unsigned long long get_ticks(void) -{ - return get_timer(0); -} - -/* - * This function is derived from PowerPC code (timebase clock frequency). - * On ARM it returns the number of timer ticks per second. - */ -ulong get_tbclk(void) -{ - return CONFIG_SPEAR_HZ; -} diff --git a/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds b/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds deleted file mode 100644 index 0964a9742e..0000000000 --- a/arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds +++ /dev/null @@ -1,54 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2015 Stefan Roese - * - * Copyright (C) 2011 Marek Vasut - * on behalf of DENX Software Engineering GmbH - * - * January 2004 - Changed to support H4 device - * Copyright (c) 2004-2008 Texas Instruments - * - * (C) Copyright 2002 - * Gary Jennejohn, DENX Software Engineering, - */ - -MEMORY { .sram : ORIGIN = IMAGE_TEXT_BASE,\ - LENGTH = IMAGE_MAX_SIZE } - -OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") -OUTPUT_ARCH(arm) -ENTRY(_start) -SECTIONS -{ - .text : - { - __start = .; - *(.vectors) - CPUDIR/spear/start.o (.text*) - *(.text*) - } > .sram - - . = ALIGN(4); - .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram - - . = ALIGN(4); - .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } > .sram - - . = ALIGN(4); - __image_copy_end = .; - _end = .; - - .bss : - { - . = ALIGN(4); - __bss_start = .; - *(.bss*) - . = ALIGN(4); - __bss_end = .; - } > .sram -} diff --git a/arch/arm/include/asm/arch-spear/clk.h b/arch/arm/include/asm/arch-spear/clk.h deleted file mode 100644 index b193f764b8..0000000000 --- a/arch/arm/include/asm/arch-spear/clk.h +++ /dev/null @@ -1,10 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2010, STMicroelectronics - All Rights Reserved - * Author(s): Vipin Kumar, for STMicroelectronics. - */ - -static inline unsigned long get_macb_pclk_rate(unsigned int dev_id) -{ - return 83000000; -} diff --git a/arch/arm/include/asm/arch-spear/gpio.h b/arch/arm/include/asm/arch-spear/gpio.h deleted file mode 100644 index 4c8c40b1c9..0000000000 --- a/arch/arm/include/asm/arch-spear/gpio.h +++ /dev/null @@ -1,23 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2012 Stefan Roese - */ - - -#ifndef __ASM_ARCH_SPEAR_GPIO_H -#define __ASM_ARCH_SPEAR_GPIO_H - -enum gpio_direction { - GPIO_DIRECTION_IN, - GPIO_DIRECTION_OUT, -}; - -struct gpio_regs { - u32 gpiodata[0x100]; /* 0x000 ... 0x3fc */ - u32 gpiodir; /* 0x400 */ -}; - -#define SPEAR_GPIO_COUNT 8 -#define DATA_REG_ADDR(gpio) (1 << (gpio + 2)) - -#endif /* __ASM_ARCH_SPEAR_GPIO_H */ diff --git a/arch/arm/include/asm/arch-spear/hardware.h b/arch/arm/include/asm/arch-spear/hardware.h deleted file mode 100644 index 69b97a03e8..0000000000 --- a/arch/arm/include/asm/arch-spear/hardware.h +++ /dev/null @@ -1,45 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2009, STMicroelectronics - All Rights Reserved - * Author(s): Vipin Kumar, for STMicroelectronics. - */ - -#ifndef _ASM_ARCH_HARDWARE_H -#define _ASM_ARCH_HARDWARE_H - -#define CONFIG_SYS_USBD_BASE 0xE1100000 -#define CONFIG_SYS_PLUG_BASE 0xE1200000 -#define CONFIG_SYS_FIFO_BASE 0xE1000800 -#define CONFIG_SYS_UHC0_EHCI_BASE 0xE1800000 -#define CONFIG_SYS_UHC1_EHCI_BASE 0xE2000000 -#define CONFIG_SYS_SMI_BASE 0xFC000000 -#define CONFIG_SPEAR_SYSCNTLBASE 0xFCA00000 -#define CONFIG_SPEAR_TIMERBASE 0xFC800000 -#define CONFIG_SPEAR_MISCBASE 0xFCA80000 -#define CONFIG_SPEAR_ETHBASE 0xE0800000 -#define CONFIG_SPEAR_MPMCBASE 0xFC600000 -#define CONFIG_SSP1_BASE 0xD0100000 -#define CONFIG_SSP2_BASE 0xD0180000 -#define CONFIG_SSP3_BASE 0xD8180000 -#define CONFIG_GPIO_BASE 0xD8100000 - -#define CONFIG_SYS_NAND_CLE (1 << 16) -#define CONFIG_SYS_NAND_ALE (1 << 17) - -#if defined(CONFIG_SPEAR600) -#define CONFIG_SYS_FSMC_BASE 0xD1800000 -#define CONFIG_FSMC_NAND_BASE 0xD2000000 - -#define CONFIG_SPEAR_BOOTSTRAPCFG 0xFCA80000 -#define CONFIG_SPEAR_BOOTSTRAPSHFT 16 -#define CONFIG_SPEAR_BOOTSTRAPMASK 0xB -#define CONFIG_SPEAR_ONLYSNORBOOT 0xA -#define CONFIG_SPEAR_NORNANDBOOT 0xB -#define CONFIG_SPEAR_NORNAND8BOOT 0x8 -#define CONFIG_SPEAR_NORNAND16BOOT 0x9 -#define CONFIG_SPEAR_USBBOOT 0x8 - -#define CONFIG_SPEAR_MPMCREGS 100 - -#endif -#endif /* _ASM_ARCH_HARDWARE_H */ diff --git a/arch/arm/include/asm/arch-spear/spr_defs.h b/arch/arm/include/asm/arch-spear/spr_defs.h deleted file mode 100644 index d09e7eb63a..0000000000 --- a/arch/arm/include/asm/arch-spear/spr_defs.h +++ /dev/null @@ -1,50 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2009 - * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. - */ - -#ifndef __SPR_DEFS_H__ -#define __SPR_DEFS_H__ - -extern int spear_board_init(ulong); -extern void setfreq(unsigned int, unsigned int); -extern unsigned int setfreq_sz; - -void plat_ddr_init(void); -void spear_late_init(void); - -int snor_boot_selected(void); -int nand_boot_selected(void); -int pnor_boot_selected(void); -int usb_boot_selected(void); -int uart_boot_selected(void); -int tftp_boot_selected(void); -int i2c_boot_selected(void); -int spi_boot_selected(void); -int mmc_boot_selected(void); - -extern u32 mpmc_conf_vals[]; - -struct chip_data { - int cpufreq; - int dramfreq; - int dramtype; - uchar version[32]; -}; - -/* HW mac id in i2c memory definitions */ -#define MAGIC_OFF 0x0 -#define MAGIC_LEN 0x2 -#define MAGIC_BYTE0 0x55 -#define MAGIC_BYTE1 0xAA -#define MAC_OFF 0x2 -#define MAC_LEN 0x6 - -#define PNOR_WIDTH_8 0 -#define PNOR_WIDTH_16 1 -#define PNOR_WIDTH_32 2 -#define PNOR_WIDTH_NUM 3 -#define PNOR_WIDTH_SEARCH 0xff - -#endif diff --git a/arch/arm/include/asm/arch-spear/spr_emi.h b/arch/arm/include/asm/arch-spear/spr_emi.h deleted file mode 100644 index 7b1cf35d3a..0000000000 --- a/arch/arm/include/asm/arch-spear/spr_emi.h +++ /dev/null @@ -1,37 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2009 - * Ryan CHEN, ST Micoelectronics, ryan.chen@st.com - */ - -#ifndef __SPEAR_EMI_H__ -#define __SPEAR_EMI_H__ - -#ifdef CONFIG_SPEAR_EMI - -struct emi_bank_regs { - u32 tap; - u32 tsdp; - u32 tdpw; - u32 tdpr; - u32 tdcs; - u32 control; -}; - -struct emi_regs { - struct emi_bank_regs bank_regs[CONFIG_SYS_MAX_FLASH_BANKS]; - u32 tout; - u32 ack; - u32 irq; -}; - -#define EMI_ACKMSK 0x40 - -/* control register definitions */ -#define EMI_CNTL_ENBBYTEW (1 << 2) -#define EMI_CNTL_ENBBYTER (1 << 3) -#define EMI_CNTL_ENBBYTERW (EMI_CNTL_ENBBYTER | EMI_CNTL_ENBBYTEW) - -#endif - -#endif diff --git a/arch/arm/include/asm/arch-spear/spr_gpt.h b/arch/arm/include/asm/arch-spear/spr_gpt.h deleted file mode 100644 index dced0a17a6..0000000000 --- a/arch/arm/include/asm/arch-spear/spr_gpt.h +++ /dev/null @@ -1,68 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2009 - * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. - */ - -#ifndef _SPR_GPT_H -#define _SPR_GPT_H - -struct gpt_regs { - u8 reserved[0x80]; - u32 control; - u32 status; - u32 compare; - u32 count; - u32 capture_re; - u32 capture_fe; -}; - -/* - * TIMER_CONTROL register settings - */ - -#define GPT_PRESCALER_MASK 0x000F -#define GPT_PRESCALER_1 0x0000 -#define GPT_PRESCALER_2 0x0001 -#define GPT_PRESCALER_4 0x0002 -#define GPT_PRESCALER_8 0x0003 -#define GPT_PRESCALER_16 0x0004 -#define GPT_PRESCALER_32 0x0005 -#define GPT_PRESCALER_64 0x0006 -#define GPT_PRESCALER_128 0x0007 -#define GPT_PRESCALER_256 0x0008 - -#define GPT_MODE_SINGLE_SHOT 0x0010 -#define GPT_MODE_AUTO_RELOAD 0x0000 - -#define GPT_ENABLE 0x0020 - -#define GPT_CAPT_MODE_MASK 0x00C0 -#define GPT_CAPT_MODE_NONE 0x0000 -#define GPT_CAPT_MODE_RE 0x0040 -#define GPT_CAPT_MODE_FE 0x0080 -#define GPT_CAPT_MODE_BOTH 0x00C0 - -#define GPT_INT_MATCH 0x0100 -#define GPT_INT_FE 0x0200 -#define GPT_INT_RE 0x0400 - -/* - * TIMER_STATUS register settings - */ - -#define GPT_STS_MATCH 0x0001 -#define GPT_STS_FE 0x0002 -#define GPT_STS_RE 0x0004 - -/* - * TIMER_COMPARE register settings - */ - -#define GPT_FREE_RUNNING 0xFFFF - -/* Timer, HZ specific defines */ -#define CONFIG_SPEAR_HZ 1000 -#define CONFIG_SPEAR_HZ_CLOCK 8300000 - -#endif diff --git a/arch/arm/include/asm/arch-spear/spr_misc.h b/arch/arm/include/asm/arch-spear/spr_misc.h deleted file mode 100644 index c1a30e24db..0000000000 --- a/arch/arm/include/asm/arch-spear/spr_misc.h +++ /dev/null @@ -1,257 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2009 - * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. - */ - -#ifndef _SPR_MISC_H -#define _SPR_MISC_H - -struct misc_regs { - u32 auto_cfg_reg; /* 0x0 */ - u32 armdbg_ctr_reg; /* 0x4 */ - u32 pll1_cntl; /* 0x8 */ - u32 pll1_frq; /* 0xc */ - u32 pll1_mod; /* 0x10 */ - u32 pll2_cntl; /* 0x14 */ - u32 pll2_frq; /* 0x18 */ - u32 pll2_mod; /* 0x1C */ - u32 pll_ctr_reg; /* 0x20 */ - u32 amba_clk_cfg; /* 0x24 */ - u32 periph_clk_cfg; /* 0x28 */ - u32 periph1_clken; /* 0x2C */ - u32 soc_core_id; /* 0x30 */ - u32 ras_clken; /* 0x34 */ - u32 periph1_rst; /* 0x38 */ - u32 periph2_rst; /* 0x3C */ - u32 ras_rst; /* 0x40 */ - u32 prsc1_clk_cfg; /* 0x44 */ - u32 prsc2_clk_cfg; /* 0x48 */ - u32 prsc3_clk_cfg; /* 0x4C */ - u32 amem_cfg_ctrl; /* 0x50 */ - u32 expi_clk_cfg; /* 0x54 */ - u32 reserved_1; /* 0x58 */ - u32 clcd_synth_clk; /* 0x5C */ - u32 irda_synth_clk; /* 0x60 */ - u32 uart_synth_clk; /* 0x64 */ - u32 gmac_synth_clk; /* 0x68 */ - u32 ras_synth1_clk; /* 0x6C */ - u32 ras_synth2_clk; /* 0x70 */ - u32 ras_synth3_clk; /* 0x74 */ - u32 ras_synth4_clk; /* 0x78 */ - u32 arb_icm_ml1; /* 0x7C */ - u32 arb_icm_ml2; /* 0x80 */ - u32 arb_icm_ml3; /* 0x84 */ - u32 arb_icm_ml4; /* 0x88 */ - u32 arb_icm_ml5; /* 0x8C */ - u32 arb_icm_ml6; /* 0x90 */ - u32 arb_icm_ml7; /* 0x94 */ - u32 arb_icm_ml8; /* 0x98 */ - u32 arb_icm_ml9; /* 0x9C */ - u32 dma_src_sel; /* 0xA0 */ - u32 uphy_ctr_reg; /* 0xA4 */ - u32 gmac_ctr_reg; /* 0xA8 */ - u32 port_bridge_ctrl; /* 0xAC */ - u32 reserved_2[4]; /* 0xB0--0xBC */ - u32 prc1_ilck_ctrl_reg; /* 0xC0 */ - u32 prc2_ilck_ctrl_reg; /* 0xC4 */ - u32 prc3_ilck_ctrl_reg; /* 0xC8 */ - u32 prc4_ilck_ctrl_reg; /* 0xCC */ - u32 prc1_intr_ctrl_reg; /* 0xD0 */ - u32 prc2_intr_ctrl_reg; /* 0xD4 */ - u32 prc3_intr_ctrl_reg; /* 0xD8 */ - u32 prc4_intr_ctrl_reg; /* 0xDC */ - u32 powerdown_cfg_reg; /* 0xE0 */ - u32 ddr_1v8_compensation; /* 0xE4 */ - u32 ddr_2v5_compensation; /* 0xE8 */ - u32 core_3v3_compensation; /* 0xEC */ - u32 ddr_pad; /* 0xF0 */ - u32 bist1_ctr_reg; /* 0xF4 */ - u32 bist2_ctr_reg; /* 0xF8 */ - u32 bist3_ctr_reg; /* 0xFC */ - u32 bist4_ctr_reg; /* 0x100 */ - u32 bist5_ctr_reg; /* 0x104 */ - u32 bist1_rslt_reg; /* 0x108 */ - u32 bist2_rslt_reg; /* 0x10C */ - u32 bist3_rslt_reg; /* 0x110 */ - u32 bist4_rslt_reg; /* 0x114 */ - u32 bist5_rslt_reg; /* 0x118 */ - u32 syst_error_reg; /* 0x11C */ - u32 reserved_3[0x1FB8]; /* 0x120--0x7FFC */ - u32 ras_gpp1_in; /* 0x8000 */ - u32 ras_gpp2_in; /* 0x8004 */ - u32 ras_gpp1_out; /* 0x8008 */ - u32 ras_gpp2_out; /* 0x800C */ -}; - -/* SYNTH_CLK value*/ -#define SYNTH23 0x00020003 - -/* PLLx_FRQ value */ -#if defined(CONFIG_SPEAR600) -#define FREQ_332 0xA600010F -#define FREQ_266 0x8500010F -#endif - -/* PLL_CTR_REG */ -#define MEM_CLK_SEL_MSK 0x70000000 -#define MEM_CLK_HCLK 0x00000000 -#define MEM_CLK_2HCLK 0x10000000 -#define MEM_CLK_PLL2 0x30000000 - -#define EXPI_CLK_CFG_LOW_COMPR 0x2000 -#define EXPI_CLK_CFG_CLK_EN 0x0400 -#define EXPI_CLK_CFG_RST 0x0200 -#define EXPI_CLK_SYNT_EN 0x0010 -#define EXPI_CLK_CFG_SEL_PLL2 0x0004 -#define EXPI_CLK_CFG_INT_CLK_EN 0x0001 - -#define PLL2_CNTL_6UA 0x1c00 -#define PLL2_CNTL_SAMPLE 0x0008 -#define PLL2_CNTL_ENABLE 0x0004 -#define PLL2_CNTL_RESETN 0x0002 -#define PLL2_CNTL_LOCK 0x0001 - -/* AUTO_CFG_REG value */ -#define MISC_SOCCFGMSK 0x0000003F -#define MISC_SOCCFG30 0x0000000C -#define MISC_SOCCFG31 0x0000000D -#define MISC_NANDDIS 0x00020000 - -/* PERIPH_CLK_CFG value */ -#define MISC_GPT3SYNTH 0x00000400 -#define MISC_GPT4SYNTH 0x00000800 -#define CONFIG_SPEAR_UART48M 0 -#define CONFIG_SPEAR_UARTCLKMSK (0x1 << 4) - -/* PRSC_CLK_CFG value */ -/* - * Fout = Fin / (2^(N+1) * (M + 1)) - */ -#define MISC_PRSC_N_1 0x00001000 -#define MISC_PRSC_M_9 0x00000009 -#define MISC_PRSC_N_4 0x00004000 -#define MISC_PRSC_M_399 0x0000018F -#define MISC_PRSC_N_6 0x00006000 -#define MISC_PRSC_M_2593 0x00000A21 -#define MISC_PRSC_M_124 0x0000007C -#define MISC_PRSC_CFG (MISC_PRSC_N_1 | MISC_PRSC_M_9) - -/* PERIPH1_CLKEN, PERIPH1_RST value */ -#define MISC_USBDENB 0x01000000 -#define MISC_ETHENB 0x00800000 -#define MISC_SMIENB 0x00200000 -#define MISC_GPIO3ENB 0x00040000 -#define MISC_GPT3ENB 0x00010000 -#define MISC_SSP3ENB 0x00004000 -#define MISC_GPIO4ENB 0x00002000 -#define MISC_GPT2ENB 0x00000800 -#define MISC_FSMCENB 0x00000200 -#define MISC_I2CENB 0x00000080 -#define MISC_SSP2ENB 0x00000040 -#define MISC_SSP1ENB 0x00000020 -#define MISC_UART0ENB 0x00000008 - -/* PERIPH_CLK_CFG */ -#define XTALTIMEEN 0x00000001 -#define PLLTIMEEN 0x00000002 -#define CLCDCLK_SYNTH 0x00000000 -#define CLCDCLK_48MHZ 0x00000004 -#define CLCDCLK_EXT 0x00000008 -#define UARTCLK_MASK (0x1 << 4) -#define UARTCLK_48MHZ 0x00000000 -#define UARTCLK_SYNTH 0x00000010 -#define IRDACLK_48MHZ 0x00000000 -#define IRDACLK_SYNTH 0x00000020 -#define IRDACLK_EXT 0x00000040 -#define RTC_DISABLE 0x00000080 -#define GPT1CLK_48MHZ 0x00000000 -#define GPT1CLK_SYNTH 0x00000100 -#define GPT2CLK_48MHZ 0x00000000 -#define GPT2CLK_SYNTH 0x00000200 -#define GPT3CLK_48MHZ 0x00000000 -#define GPT3CLK_SYNTH 0x00000400 -#define GPT4CLK_48MHZ 0x00000000 -#define GPT4CLK_SYNTH 0x00000800 -#define GPT5CLK_48MHZ 0x00000000 -#define GPT5CLK_SYNTH 0x00001000 -#define GPT1_FREEZE 0x00002000 -#define GPT2_FREEZE 0x00004000 -#define GPT3_FREEZE 0x00008000 -#define GPT4_FREEZE 0x00010000 -#define GPT5_FREEZE 0x00020000 - -/* PERIPH1_CLKEN bits */ -#define PERIPH_ARM1_WE 0x00000001 -#define PERIPH_ARM1 0x00000002 -#define PERIPH_ARM2 0x00000004 -#define PERIPH_UART1 0x00000008 -#define PERIPH_UART2 0x00000010 -#define PERIPH_SSP1 0x00000020 -#define PERIPH_SSP2 0x00000040 -#define PERIPH_I2C 0x00000080 -#define PERIPH_JPEG 0x00000100 -#define PERIPH_FSMC 0x00000200 -#define PERIPH_FIRDA 0x00000400 -#define PERIPH_GPT4 0x00000800 -#define PERIPH_GPT5 0x00001000 -#define PERIPH_GPIO4 0x00002000 -#define PERIPH_SSP3 0x00004000 -#define PERIPH_ADC 0x00008000 -#define PERIPH_GPT3 0x00010000 -#define PERIPH_RTC 0x00020000 -#define PERIPH_GPIO3 0x00040000 -#define PERIPH_DMA 0x00080000 -#define PERIPH_ROM 0x00100000 -#define PERIPH_SMI 0x00200000 -#define PERIPH_CLCD 0x00400000 -#define PERIPH_GMAC 0x00800000 -#define PERIPH_USBD 0x01000000 -#define PERIPH_USBH1 0x02000000 -#define PERIPH_USBH2 0x04000000 -#define PERIPH_MPMC 0x08000000 -#define PERIPH_RAMW 0x10000000 -#define PERIPH_MPMC_EN 0x20000000 -#define PERIPH_MPMC_WE 0x40000000 -#define PERIPH_MPMCMSK 0x60000000 - -#define PERIPH_CLK_ALL 0x0FFFFFF8 -#define PERIPH_RST_ALL 0x00000004 - -/* DDR_PAD values */ -#define DDR_PAD_CNF_MSK 0x0000ffff -#define DDR_PAD_SW_CONF 0x00060000 -#define DDR_PAD_SSTL_SEL 0x00000001 -#define DDR_PAD_DRAM_TYPE 0x00008000 - -/* DDR_COMP values */ -#define DDR_COMP_ACCURATE 0x00000010 - -/* SoC revision stuff */ -#define SOC_PRI_SHFT 16 -#define SOC_SEC_SHFT 8 - -/* Revision definitions */ -#define SOC_SPEAR_NA 0 - -/* - * The definitons have started from - * 101 for SPEAr6xx - * 201 for SPEAr3xx - * 301 for SPEAr13xx - */ -#define SOC_SPEAR600_AA 101 -#define SOC_SPEAR600_AB 102 -#define SOC_SPEAR600_BA 103 -#define SOC_SPEAR600_BB 104 -#define SOC_SPEAR600_BC 105 -#define SOC_SPEAR600_BD 106 - -#define SOC_SPEAR300 201 -#define SOC_SPEAR310 202 -#define SOC_SPEAR320 203 - -extern int get_socrev(void); -int fsmc_nand_switch_ecc(uint32_t eccstrength); - -#endif diff --git a/arch/arm/include/asm/arch-spear/spr_ssp.h b/arch/arm/include/asm/arch-spear/spr_ssp.h deleted file mode 100644 index 088d34b405..0000000000 --- a/arch/arm/include/asm/arch-spear/spr_ssp.h +++ /dev/null @@ -1,28 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2012 Stefan Roese - */ - -#ifndef _SPR_SSP_H -#define _SPR_SSP_H - -struct ssp_regs { - u32 sspcr0; - u32 sspcr1; - u32 sspdr; - u32 sspsr; - u32 sspcpsr; - u32 sspimsc; - u32 sspicr; - u32 sspdmacr; -}; - -#define SSPCR0_FRF_MOT_SPI 0x0000 -#define SSPCR0_DSS_16BITS 0x000f - -#define SSPCR1_SSE 0x0002 - -#define SSPSR_TNF 0x2 -#define SSPSR_TFE 0x1 - -#endif diff --git a/arch/arm/include/asm/arch-spear/spr_syscntl.h b/arch/arm/include/asm/arch-spear/spr_syscntl.h deleted file mode 100644 index 6a83d87d13..0000000000 --- a/arch/arm/include/asm/arch-spear/spr_syscntl.h +++ /dev/null @@ -1,35 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2009 - * Ryan CHEN, ST Micoelectronics, ryan.chen@st.com - */ - -#ifndef __SYSCTRL_H -#define __SYSCTRL_H - -struct syscntl_regs { - u32 scctrl; - u32 scsysstat; - u32 scimctrl; - u32 scimsysstat; - u32 scxtalctrl; - u32 scpllctrl; - u32 scpllfctrl; - u32 scperctrl0; - u32 scperctrl1; - u32 scperen; - u32 scperdis; - const u32 scperclken; - const u32 scperstat; -}; - -#define MODE_SHIFT 0x00000003 - -#define NORMAL 0x00000004 -#define SLOW 0x00000002 -#define DOZE 0x00000001 -#define SLEEP 0x00000000 - -#define PLL_TIM 0x01FFFFFF - -#endif diff --git a/board/spear/spear600/Kconfig b/board/spear/spear600/Kconfig deleted file mode 100644 index d562e64f07..0000000000 --- a/board/spear/spear600/Kconfig +++ /dev/null @@ -1,15 +0,0 @@ -if TARGET_SPEAR600 - -config SYS_BOARD - default "spear600" - -config SYS_VENDOR - default "spear" - -config SYS_SOC - default "spear" - -config SYS_CONFIG_NAME - default "spear6xx_evb" - -endif diff --git a/board/spear/spear600/MAINTAINERS b/board/spear/spear600/MAINTAINERS deleted file mode 100644 index ddcd11a873..0000000000 --- a/board/spear/spear600/MAINTAINERS +++ /dev/null @@ -1,13 +0,0 @@ -SPEAR600 BOARD -M: Vipin Kumar -S: Maintained -F: board/spear/spear600/ -F: include/configs/spear6xx_evb.h -F: configs/spear600_defconfig - -SPEAR600_NAND BOARD -#M: - -S: Maintained -F: configs/spear600_nand_defconfig -F: configs/spear600_usbtty_defconfig -F: configs/spear600_usbtty_nand_defconfig diff --git a/board/spear/spear600/Makefile b/board/spear/spear600/Makefile deleted file mode 100644 index d25163e3f1..0000000000 --- a/board/spear/spear600/Makefile +++ /dev/null @@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2000-2004 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. - -obj-y += spear600.o diff --git a/board/spear/spear600/spear600.c b/board/spear/spear600/spear600.c deleted file mode 100644 index 4706c52c12..0000000000 --- a/board/spear/spear600/spear600.c +++ /dev/null @@ -1,56 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2009 - * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE]; - -int board_init(void) -{ - return spear_board_init(MACH_TYPE_SPEAR600); -} - -/* - * board_nand_init - Board specific NAND initialization - * @nand: mtd private chip structure - * - * Called by nand_init_chip to initialize the board specific functions - */ - -void board_nand_init() -{ - struct misc_regs *const misc_regs_p = - (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - struct nand_chip *nand = &nand_chip[0]; - -#if defined(CONFIG_NAND_FSMC) - if (!(readl(&misc_regs_p->auto_cfg_reg) & MISC_NANDDIS)) - fsmc_nand_init(nand); -#endif - return; -} - -int board_eth_init(struct bd_info *bis) -{ - int ret = 0; - -#if defined(CONFIG_ETH_DESIGNWARE) - u32 interface = PHY_INTERFACE_MODE_MII; - if (designware_initialize(CONFIG_SPEAR_ETHBASE, interface) >= 0) - ret++; -#endif - return ret; -} diff --git a/board/spear/x600/Kconfig b/board/spear/x600/Kconfig deleted file mode 100644 index 59f2b1ef56..0000000000 --- a/board/spear/x600/Kconfig +++ /dev/null @@ -1,18 +0,0 @@ -if TARGET_X600 - -config SPL_LDSCRIPT - default "arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds" - -config SYS_BOARD - default "x600" - -config SYS_VENDOR - default "spear" - -config SYS_SOC - default "spear" - -config SYS_CONFIG_NAME - default "x600" - -endif diff --git a/board/spear/x600/MAINTAINERS b/board/spear/x600/MAINTAINERS deleted file mode 100644 index bff6824945..0000000000 --- a/board/spear/x600/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -X600 BOARD -M: Stefan Roese -S: Maintained -F: board/spear/x600/ -F: include/configs/x600.h -F: configs/x600_defconfig diff --git a/board/spear/x600/Makefile b/board/spear/x600/Makefile deleted file mode 100644 index 3ed8415777..0000000000 --- a/board/spear/x600/Makefile +++ /dev/null @@ -1,11 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2000-2004 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. - -ifdef CONFIG_SPL_BUILD -# necessary to create built-in.o -obj- := __dummy__.o -else -obj-y := fpga.o x600.o -endif diff --git a/board/spear/x600/fpga.c b/board/spear/x600/fpga.c deleted file mode 100644 index 5140694b9e..0000000000 --- a/board/spear/x600/fpga.c +++ /dev/null @@ -1,265 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2012 Stefan Roese - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -/* - * FPGA program pin configuration on X600: - * - * Only PROG and DONE are connected to GPIOs. INIT is not connected to the - * SoC at all. And CLOCK and DATA are connected to the SSP2 port. We use - * 16bit serial writes via this SSP port to write the data bits into the - * FPGA. - */ -#define CONFIG_SYS_FPGA_PROG 2 -#define CONFIG_SYS_FPGA_DONE 3 - -/* - * Set the active-low FPGA reset signal. - */ -static void fpga_reset(int assert) -{ - /* - * On x600 we have no means to toggle the FPGA reset signal - */ - debug("%s:%d: RESET (%d)\n", __func__, __LINE__, assert); -} - -/* - * Set the FPGA's active-low SelectMap program line to the specified level - */ -static int fpga_pgm_fn(int assert, int flush, int cookie) -{ - debug("%s:%d: FPGA PROG (%d)\n", __func__, __LINE__, assert); - - gpio_set_value(CONFIG_SYS_FPGA_PROG, assert); - - return assert; -} - -/* - * Test the state of the active-low FPGA INIT line. Return 1 on INIT - * asserted (low). - */ -static int fpga_init_fn(int cookie) -{ - static int state; - - debug("%s:%d: init (state=%d)\n", __func__, __LINE__, state); - - /* - * On x600, the FPGA INIT signal is not connected to the SoC. - * We can't read the INIT status. Let's return the "correct" - * INIT signal state generated via a local state-machine. - */ - if (++state == 1) { - return 1; - } else { - state = 0; - return 0; - } -} - -/* - * Test the state of the active-high FPGA DONE pin - */ -static int fpga_done_fn(int cookie) -{ - struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE; - - /* - * Wait for Tx-FIFO to become empty before looking for DONE - */ - while (!(readl(&ssp->sspsr) & SSPSR_TFE)) - ; - - if (gpio_get_value(CONFIG_SYS_FPGA_DONE)) - return 1; - else - return 0; -} - -/* - * FPGA pre-configuration function. Just make sure that - * FPGA reset is asserted to keep the FPGA from starting up after - * configuration. - */ -static int fpga_pre_config_fn(int cookie) -{ - debug("%s:%d: FPGA pre-configuration\n", __func__, __LINE__); - fpga_reset(true); - - return 0; -} - -/* - * FPGA post configuration function. Blip the FPGA reset line and then see if - * the FPGA appears to be running. - */ -static int fpga_post_config_fn(int cookie) -{ - int rc = 0; - - debug("%s:%d: FPGA post configuration\n", __func__, __LINE__); - - fpga_reset(true); - udelay(100); - fpga_reset(false); - udelay(100); - - return rc; -} - -static int fpga_clk_fn(int assert_clk, int flush, int cookie) -{ - /* - * No dedicated clock signal on x600 (data & clock generated) - * in SSP interface. So we don't have to do anything here. - */ - return assert_clk; -} - -static int fpga_wr_fn(int assert_write, int flush, int cookie) -{ - struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE; - static int count; - static u16 data; - - /* - * First collect 16 bits of data - */ - data = data << 1; - if (assert_write) - data |= 1; - - /* - * If 16 bits are not available, return for more bits - */ - count++; - if (count != 16) - return assert_write; - - count = 0; - - /* - * Wait for Tx-FIFO to become ready - */ - while (!(readl(&ssp->sspsr) & SSPSR_TNF)) - ; - - /* Send 16 bits to FPGA via SSP bus */ - writel(data, &ssp->sspdr); - - return assert_write; -} - -static xilinx_spartan3_slave_serial_fns x600_fpga_fns = { - fpga_pre_config_fn, - fpga_pgm_fn, - fpga_clk_fn, - fpga_init_fn, - fpga_done_fn, - fpga_wr_fn, - fpga_post_config_fn, -}; - -static xilinx_desc fpga[CONFIG_FPGA_COUNT] = { - XILINX_XC3S1200E_DESC(slave_serial, &x600_fpga_fns, 0) -}; - -/* - * Initialize the SelectMap interface. We assume that the mode and the - * initial state of all of the port pins have already been set! - */ -static void fpga_serialslave_init(void) -{ - debug("%s:%d: Initialize serial slave interface\n", __func__, __LINE__); - fpga_pgm_fn(false, false, 0); /* make sure program pin is inactive */ -} - -static int expi_setup(int freq) -{ - struct misc_regs *misc = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - int pll2_m, pll2_n, pll2_p, expi_x, expi_y; - - pll2_m = (freq * 2) / 1000; - pll2_n = 15; - pll2_p = 1; - expi_x = 1; - expi_y = 2; - - /* - * Disable reset, Low compression, Disable retiming, Enable Expi, - * Enable soft reset, DMA, PLL2, Internal - */ - writel(EXPI_CLK_CFG_LOW_COMPR | EXPI_CLK_CFG_CLK_EN | EXPI_CLK_CFG_RST | - EXPI_CLK_SYNT_EN | EXPI_CLK_CFG_SEL_PLL2 | - EXPI_CLK_CFG_INT_CLK_EN | (expi_y << 16) | (expi_x << 24), - &misc->expi_clk_cfg); - - /* - * 6 uA, Internal feedback, 1st order, Non-dithered, Sample Parameters, - * Enable PLL2, Disable reset - */ - writel((pll2_m << 24) | (pll2_p << 8) | (pll2_n), &misc->pll2_frq); - writel(PLL2_CNTL_6UA | PLL2_CNTL_SAMPLE | PLL2_CNTL_ENABLE | - PLL2_CNTL_RESETN | PLL2_CNTL_LOCK, &misc->pll2_cntl); - - /* - * Disable soft reset - */ - clrbits_le32(&misc->expi_clk_cfg, EXPI_CLK_CFG_RST); - - return 0; -} - -/* - * Initialize the fpga - */ -int x600_init_fpga(void) -{ - struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE; - struct misc_regs *misc = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - - /* Enable SSP2 clock */ - writel(readl(&misc->periph1_clken) | MISC_SSP2ENB | MISC_GPIO4ENB, - &misc->periph1_clken); - - /* Set EXPI clock to 45 MHz */ - expi_setup(45000); - - /* Configure GPIO directions */ - gpio_direction_output(CONFIG_SYS_FPGA_PROG, 0); - gpio_direction_input(CONFIG_SYS_FPGA_DONE); - - writel(SSPCR0_DSS_16BITS, &ssp->sspcr0); - writel(SSPCR1_SSE, &ssp->sspcr1); - - /* - * Set lowest prescale divisor value (CPSDVSR) of 2 for max download - * speed. - * - * Actual data clock rate is: 80MHz / (CPSDVSR * (SCR + 1)) - * With CPSDVSR at 2 and SCR at 0, the maximume clock rate is 40MHz. - */ - writel(2, &ssp->sspcpsr); - - fpga_init(); - fpga_serialslave_init(); - - debug("%s:%d: Adding fpga 0\n", __func__, __LINE__); - fpga_add(fpga_xilinx, &fpga[0]); - - return 0; -} diff --git a/board/spear/x600/fpga.h b/board/spear/x600/fpga.h deleted file mode 100644 index f5e6f31a48..0000000000 --- a/board/spear/x600/fpga.h +++ /dev/null @@ -1,6 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2012 Stefan Roese - */ - -int x600_init_fpga(void); diff --git a/board/spear/x600/x600.c b/board/spear/x600/x600.c deleted file mode 100644 index 9c30581ec0..0000000000 --- a/board/spear/x600/x600.c +++ /dev/null @@ -1,150 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2009 - * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. - * - * Copyright (C) 2012 Stefan Roese - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include "fpga.h" - -static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE]; - -int board_init(void) -{ - /* - * X600 is equipped with an M41T82 RTC. This RTC has the - * HT bit (Halt Update), which needs to be cleared upon - * power-up. Otherwise the RTC is halted. - */ - rtc_reset(); - - return spear_board_init(MACH_TYPE_SPEAR600); -} - -int board_late_init(void) -{ - /* - * Monitor and env protection on by default - */ - flash_protect(FLAG_PROTECT_SET, - CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + - CONFIG_SYS_SPL_LEN + CONFIG_SYS_MONITOR_LEN + - 2 * CONFIG_ENV_SECT_SIZE - 1, - &flash_info[0]); - - /* Init FPGA subsystem */ - x600_init_fpga(); - - return 0; -} - -/* - * board_nand_init - Board specific NAND initialization - * @nand: mtd private chip structure - * - * Called by nand_init_chip to initialize the board specific functions - */ - -void board_nand_init(void) -{ - struct misc_regs *const misc_regs_p = - (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - struct nand_chip *nand = &nand_chip[0]; - - if (!(readl(&misc_regs_p->auto_cfg_reg) & MISC_NANDDIS)) - fsmc_nand_init(nand); -} - -int board_phy_config(struct phy_device *phydev) -{ - unsigned short id1, id2; - - /* check whether KSZ9031 or AR8035 has to be configured */ - id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2); - id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3); - - if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) { - /* PHY configuration for Micrel KSZ9031 */ - printf("PHY KSZ9031 detected - "); - - phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, 0x1c00); - - /* control data pad skew - devaddr = 0x02, register = 0x04 */ - ksz9031_phy_extended_write(phydev, 0x02, - MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW, - MII_KSZ9031_MOD_DATA_NO_POST_INC, - 0x0000); - /* rx data pad skew - devaddr = 0x02, register = 0x05 */ - ksz9031_phy_extended_write(phydev, 0x02, - MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, - MII_KSZ9031_MOD_DATA_NO_POST_INC, - 0x0000); - /* tx data pad skew - devaddr = 0x02, register = 0x05 */ - ksz9031_phy_extended_write(phydev, 0x02, - MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, - MII_KSZ9031_MOD_DATA_NO_POST_INC, - 0x0000); - /* gtx and rx clock pad skew - devaddr = 0x02, reg = 0x08 */ - ksz9031_phy_extended_write(phydev, 0x02, - MII_KSZ9031_EXT_RGMII_CLOCK_SKEW, - MII_KSZ9031_MOD_DATA_NO_POST_INC, - 0x03FF); - } else { - /* PHY configuration for Vitesse VSC8641 */ - printf("PHY VSC8641 detected - "); - - /* Extended PHY control 1, select GMII */ - phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020); - - /* Software reset necessary after GMII mode selction */ - phy_reset(phydev); - - /* Enable extended page register access */ - phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001); - - /* 17e: Enhanced LED behavior, needs to be written twice */ - phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff); - phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff); - - /* 16e: Enhanced LED method select */ - phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea); - - /* Disable extended page register access */ - phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000); - - /* Enable clock output pin */ - phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049); - } - - if (phydev->drv->config) - phydev->drv->config(phydev); - - return 0; -} - -int board_eth_init(struct bd_info *bis) -{ - int ret = 0; - - if (designware_initialize(CONFIG_SPEAR_ETHBASE, - PHY_INTERFACE_MODE_GMII) >= 0) - ret++; - - return ret; -} diff --git a/configs/spear600_defconfig b/configs/spear600_defconfig deleted file mode 100644 index 36c55eb2b3..0000000000 --- a/configs/spear600_defconfig +++ /dev/null @@ -1,39 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_CPU_INIT=y -CONFIG_TARGET_SPEAR600=y -CONFIG_SYS_TEXT_BASE=0x00700000 -CONFIG_NR_DRAM_BANKS=1 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_IDENT_STRING="-SPEAr" -CONFIG_SYS_EXTRA_OPTIONS="SPEAR600" -CONFIG_BOOTDELAY=1 -CONFIG_AUTOBOOT_KEYED=y -CONFIG_AUTOBOOT_PROMPT="Hit SPACE in %d seconds to stop autoboot.\n" -CONFIG_AUTOBOOT_STOP_STR=" " -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyAMA0,115200 mem=128M root=/dev/mtdblock3 rootfstype=jffs2" -CONFIG_SYS_CONSOLE_INFO_QUIET=y -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_MISC_INIT_R=y -# CONFIG_AUTO_COMPLETE is not set -CONFIG_CMD_IMLS=y -CONFIG_CMD_I2C=y -CONFIG_CMD_NAND=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xF8040000 -CONFIG_SYS_I2C_DW=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_MTD_RAW_NAND=y -CONFIG_PHY_NATSEMI=y -CONFIG_PHY_GIGE=y -CONFIG_ETH_DESIGNWARE=y -CONFIG_MII=y -CONFIG_CONS_INDEX=0 diff --git a/configs/spear600_nand_defconfig b/configs/spear600_nand_defconfig deleted file mode 100644 index 9465fe129d..0000000000 --- a/configs/spear600_nand_defconfig +++ /dev/null @@ -1,36 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_CPU_INIT=y -CONFIG_TARGET_SPEAR600=y -CONFIG_SYS_TEXT_BASE=0x00700000 -CONFIG_NR_DRAM_BANKS=1 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x60000 -CONFIG_IDENT_STRING="-SPEAr" -CONFIG_SYS_EXTRA_OPTIONS="SPEAR600" -CONFIG_BOOTDELAY=1 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyAMA0,115200 mem=128M root=/dev/mtdblock7 rootfstype=jffs2" -CONFIG_SYS_CONSOLE_INFO_QUIET=y -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_MISC_INIT_R=y -# CONFIG_AUTO_COMPLETE is not set -CONFIG_CMD_IMLS=y -CONFIG_CMD_I2C=y -CONFIG_CMD_NAND=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_NAND=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_SYS_I2C_DW=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_MTD_RAW_NAND=y -CONFIG_PHY_NATSEMI=y -CONFIG_PHY_GIGE=y -CONFIG_ETH_DESIGNWARE=y -CONFIG_MII=y -CONFIG_CONS_INDEX=0 diff --git a/configs/spear600_usbtty_defconfig b/configs/spear600_usbtty_defconfig deleted file mode 100644 index e83c748b65..0000000000 --- a/configs/spear600_usbtty_defconfig +++ /dev/null @@ -1,38 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_CPU_INIT=y -CONFIG_TARGET_SPEAR600=y -CONFIG_SYS_TEXT_BASE=0x00700000 -CONFIG_NR_DRAM_BANKS=1 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_IDENT_STRING="-SPEAr" -CONFIG_SYS_EXTRA_OPTIONS="SPEAR600,USBTTY" -CONFIG_BOOTDELAY=-1 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyAMA0,115200 mem=128M root=/dev/mtdblock3 rootfstype=jffs2" -CONFIG_SYS_CONSOLE_INFO_QUIET=y -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_MISC_INIT_R=y -# CONFIG_AUTO_COMPLETE is not set -CONFIG_CMD_IMLS=y -CONFIG_CMD_I2C=y -CONFIG_CMD_NAND=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_ENV_ADDR=0xF8040000 -CONFIG_SYS_I2C_DW=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_MTD_RAW_NAND=y -CONFIG_PHY_NATSEMI=y -CONFIG_PHY_GIGE=y -CONFIG_ETH_DESIGNWARE=y -CONFIG_MII=y -CONFIG_CONS_INDEX=0 -CONFIG_USB=y -CONFIG_USB_GADGET=y diff --git a/configs/spear600_usbtty_nand_defconfig b/configs/spear600_usbtty_nand_defconfig deleted file mode 100644 index ec3a440c11..0000000000 --- a/configs/spear600_usbtty_nand_defconfig +++ /dev/null @@ -1,38 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_CPU_INIT=y -CONFIG_TARGET_SPEAR600=y -CONFIG_SYS_TEXT_BASE=0x00700000 -CONFIG_NR_DRAM_BANKS=1 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x60000 -CONFIG_IDENT_STRING="-SPEAr" -CONFIG_SYS_EXTRA_OPTIONS="SPEAR600,USBTTY" -CONFIG_BOOTDELAY=-1 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyAMA0,115200 mem=128M root=/dev/mtdblock7 rootfstype=jffs2" -CONFIG_SYS_CONSOLE_INFO_QUIET=y -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_MISC_INIT_R=y -# CONFIG_AUTO_COMPLETE is not set -CONFIG_CMD_IMLS=y -CONFIG_CMD_I2C=y -CONFIG_CMD_NAND=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_NAND=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_SYS_I2C_DW=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_MTD_RAW_NAND=y -CONFIG_PHY_NATSEMI=y -CONFIG_PHY_GIGE=y -CONFIG_ETH_DESIGNWARE=y -CONFIG_MII=y -CONFIG_CONS_INDEX=0 -CONFIG_USB=y -CONFIG_USB_GADGET=y diff --git a/configs/x600_defconfig b/configs/x600_defconfig deleted file mode 100644 index 8fb29b3724..0000000000 --- a/configs/x600_defconfig +++ /dev/null @@ -1,71 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_CPU_INIT=y -CONFIG_SYS_THUMB_BUILD=y -# CONFIG_SPL_USE_ARCH_MEMCPY is not set -# CONFIG_SPL_USE_ARCH_MEMSET is not set -CONFIG_TARGET_X600=y -CONFIG_SYS_TEXT_BASE=0x00800040 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=1 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_SPL_TEXT_BASE=0xd2800b00 -CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SYS_BOOTCOUNT_ADDR=0xD2801FF8 -CONFIG_SPL=y -CONFIG_IDENT_STRING="-SPEAr" -CONFIG_BOOTDELAY=3 -CONFIG_AUTOBOOT_KEYED=y -CONFIG_AUTOBOOT_PROMPT="Hit SPACE in %d seconds to stop autoboot.\n" -CONFIG_AUTOBOOT_STOP_STR=" " -CONFIG_SYS_CONSOLE_INFO_QUIET=y -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_MISC_INIT_R=y -CONFIG_SPL_NOR_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_SYS_PROMPT="X600> " -CONFIG_CMD_IMLS=y -CONFIG_LOOPW=y -CONFIG_CMD_MX_CYCLIC=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_I2C=y -CONFIG_CMD_NAND=y -CONFIG_CMD_SAVES=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y -CONFIG_CMD_FAT=y -CONFIG_CMD_FS_GENERIC=y -CONFIG_CMD_MTDPARTS=y -CONFIG_MTDIDS_DEFAULT="nand0=nand" -CONFIG_MTDPARTS_DEFAULT="mtdparts=nand:64M(ubi0),64M(ubi1)" -CONFIG_CMD_UBI=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_SYS_REDUNDAND_ENVIRONMENT=y -CONFIG_ENV_ADDR=0xF8060000 -CONFIG_ENV_ADDR_REDUND=0xF8070000 -CONFIG_BOOTCOUNT_LIMIT=y -CONFIG_FPGA_XILINX=y -CONFIG_FPGA_SPARTAN3=y -CONFIG_SYS_I2C_DW=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_MTD_RAW_NAND=y -CONFIG_PHY_ADDR_ENABLE=y -CONFIG_PHY_MICREL=y -CONFIG_PHY_MICREL_KSZ90X1=y -CONFIG_ETH_DESIGNWARE=y -CONFIG_MII=y -CONFIG_RTC_M41T62=y -CONFIG_CONS_INDEX=0 -CONFIG_USB=y -CONFIG_USB_EHCI_HCD=y -CONFIG_USB_STORAGE=y -CONFIG_BCH=y -CONFIG_OF_LIBFDT=y diff --git a/doc/README.spear b/doc/README.spear deleted file mode 100644 index 0789b3fd27..0000000000 --- a/doc/README.spear +++ /dev/null @@ -1,74 +0,0 @@ - -SPEAr (Structured Processor Enhanced Architecture). - -SPEAr600 is also known as SPEArPlus and SPEAr300 is also known as SPEArBasic - -The SPEAr SoC family embeds a customizable logic that can be programmed -one-time by a customer at silicon mask level (i.e. not at runtime!). - -U-Boot supports four SoCs: SPEAr600, SPEAr3xx - -All 4 SoCs (SPEAr3xx and SPEAr600) share common peripherals. SPEAr300 and -SPEAr600 do not have EMI. - -1. ARM926ejs core based (sp600 has two cores, the 2nd handled only in Linux) -2. FastEthernet (sp600 has Gbit version, but same controller - GMAC) -3. USB Host -4. USB Device -5. NAND controller (FSMC) -6. Serial NOR ctrl -7. I2C -8. SPI -9. CLCD -10. others .. - -Everything is supported in Linux. -u-boot is currently not supporting all peripeharls (just a few as listed below). -1. USB Device -2. NAND controller (FSMC) -3. Serial Memory Interface -4. EMI (Parallel NOR interface) -4. I2C -5. UART - -Build options - make spear320_config - spear320 build with environment variables placed at default - location i.e. Serial NOR device - make spear320_pnor_config - This option generates a uboot image that supports emi controller - for CFI compliant parallel NOR flash. Environment variables are - placed in Parallel NOR device - make spear320_nand_config - spear320 build with environment variables placed in NAND device - make spear320_usbtty_config - spear320 build with usbtty terminal as default and environment - placed at default location - make spear320_usbtty_pnor_config - spear320 build with usbtty terminal as default and environment - placed in pnor device - make spear320_usbtty_nand_config - Build with usbtty terminal as default and environment placed in - NAND device - make spear300_config - make spear300_nand_config - make spear300_usbtty_config - make spear300_usbtty_nand_config - make spear310_config - make spear310_pnor_config - make spear310_nand_config - make spear310_usbtty_config - make spear310_usbtty_pnor_config - make spear310_usbtty_nand_config - make spear600_config - make spear600_nand_config - make spear600_usbtty_config - make spear600_usbtty_nand_config - -Mac id storage and retrieval in spear platforms - -Please read doc/README.enetaddr for the implementation guidelines for mac id -usage. Basically, environment has precedence over board specific storage. The -ethaddr beeing used for the network interface is always taken only from -environment variables. Although, we can check the mac id programmed in i2c -memory by using chip_config command diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 8541ba0b0a..06dfc32fa5 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -33,7 +33,6 @@ obj-$(CONFIG_RCAR_GPIO) += gpio-rcar.o obj-$(CONFIG_RZA1_GPIO) += gpio-rza1.o obj-$(CONFIG_S5P) += s5p_gpio.o obj-$(CONFIG_SANDBOX_GPIO) += sandbox.o -obj-$(CONFIG_SPEAR_GPIO) += spear_gpio.o obj-$(CONFIG_TEGRA_GPIO) += tegra_gpio.o obj-$(CONFIG_TEGRA186_GPIO) += tegra186_gpio.o obj-$(CONFIG_DA8XX_GPIO) += da8xx_gpio.o diff --git a/drivers/gpio/spear_gpio.c b/drivers/gpio/spear_gpio.c deleted file mode 100644 index 4e4cd12545..0000000000 --- a/drivers/gpio/spear_gpio.c +++ /dev/null @@ -1,89 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2012 Stefan Roese - */ - -/* - * Driver for SPEAr600 GPIO controller - */ - -#include -#include -#include -#include -#include -#include - -static int gpio_direction(unsigned gpio, - enum gpio_direction direction) -{ - struct gpio_regs *regs = (struct gpio_regs *)CONFIG_GPIO_BASE; - u32 val; - - val = readl(®s->gpiodir); - - if (direction == GPIO_DIRECTION_OUT) - val |= 1 << gpio; - else - val &= ~(1 << gpio); - - writel(val, ®s->gpiodir); - - return 0; -} - -int gpio_set_value(unsigned gpio, int value) -{ - struct gpio_regs *regs = (struct gpio_regs *)CONFIG_GPIO_BASE; - - if (value) - writel(1 << gpio, ®s->gpiodata[DATA_REG_ADDR(gpio)]); - else - writel(0, ®s->gpiodata[DATA_REG_ADDR(gpio)]); - - return 0; -} - -int gpio_get_value(unsigned gpio) -{ - struct gpio_regs *regs = (struct gpio_regs *)CONFIG_GPIO_BASE; - u32 val; - - val = readl(®s->gpiodata[DATA_REG_ADDR(gpio)]); - - return !!val; -} - -int gpio_request(unsigned gpio, const char *label) -{ - if (gpio >= SPEAR_GPIO_COUNT) - return -EINVAL; - - return 0; -} - -int gpio_free(unsigned gpio) -{ - return 0; -} - -void gpio_toggle_value(unsigned gpio) -{ - gpio_set_value(gpio, !gpio_get_value(gpio)); -} - -int gpio_direction_input(unsigned gpio) -{ - return gpio_direction(gpio, GPIO_DIRECTION_IN); -} - -int gpio_direction_output(unsigned gpio, int value) -{ - int ret = gpio_direction(gpio, GPIO_DIRECTION_OUT); - - if (ret < 0) - return ret; - - gpio_set_value(gpio, value); - return 0; -} diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig index de57ab928a..35d6e2c8ec 100644 --- a/drivers/i2c/Kconfig +++ b/drivers/i2c/Kconfig @@ -136,16 +136,6 @@ config SYS_I2C_DW controller is used in various SoCs, e.g. the ST SPEAr, Altera SoCFPGA, Synopsys ARC700 and some Intel x86 SoCs. -config SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED - bool "DW I2C Enable Status Register not supported" - depends on SYS_I2C_DW && \ - (TARGET_SPEAR600 || TARGET_X600) - default y - help - Some versions of the Designware I2C controller do not support the - enable status register. This config option can be enabled in such - cases. - config SYS_I2C_ASPEED bool "Aspeed I2C Controller" depends on DM_I2C && ARCH_ASPEED diff --git a/drivers/i2c/designware_i2c.c b/drivers/i2c/designware_i2c.c index 072803691e..e57eed0f6c 100644 --- a/drivers/i2c/designware_i2c.c +++ b/drivers/i2c/designware_i2c.c @@ -24,16 +24,6 @@ */ #define DW_I2C_COMP_TYPE 0x44570140 -#ifdef CONFIG_SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED -static int dw_i2c_enable(struct i2c_regs *i2c_base, bool enable) -{ - u32 ena = enable ? IC_ENABLE_0B : 0; - - writel(ena, &i2c_base->ic_enable); - - return 0; -} -#else static int dw_i2c_enable(struct i2c_regs *i2c_base, bool enable) { u32 ena = enable ? IC_ENABLE_0B : 0; @@ -55,7 +45,6 @@ static int dw_i2c_enable(struct i2c_regs *i2c_base, bool enable) return -ETIMEDOUT; } -#endif /* High and low times in different speed modes (in ns) */ enum { diff --git a/drivers/mtd/nand/raw/fsmc_nand.c b/drivers/mtd/nand/raw/fsmc_nand.c index 1f4c74f0f6..1c24710b2d 100644 --- a/drivers/mtd/nand/raw/fsmc_nand.c +++ b/drivers/mtd/nand/raw/fsmc_nand.c @@ -389,55 +389,6 @@ static int fsmc_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, return 0; } -#ifndef CONFIG_SPL_BUILD -/* - * fsmc_nand_switch_ecc - switch the ECC operation between different engines - * - * @eccstrength - the number of bits that could be corrected - * (1 - HW, 4 - SW BCH4) - */ -int fsmc_nand_switch_ecc(uint32_t eccstrength) -{ - struct nand_chip *nand; - struct mtd_info *mtd; - int err; - - /* - * This functions is only called on SPEAr600 platforms, supporting - * 1 bit HW ECC. The BCH8 HW ECC (FSMC_VER8) from the ST-Ericsson - * Nomadik SoC is currently supporting this fsmc_nand_switch_ecc() - * function, as it doesn't need to switch to a different ECC layout. - */ - mtd = get_nand_dev_by_index(nand_curr_device); - nand = mtd_to_nand(mtd); - - /* Setup the ecc configurations again */ - if (eccstrength == 1) { - nand->ecc.mode = NAND_ECC_HW; - nand->ecc.bytes = 3; - nand->ecc.strength = 1; - nand->ecc.layout = &fsmc_ecc1_layout; - nand->ecc.calculate = fsmc_read_hwecc; - nand->ecc.correct = nand_correct_data; - } else if (eccstrength == 4) { - /* - * .calculate .correct and .bytes will be set in - * nand_scan_tail() - */ - nand->ecc.mode = NAND_ECC_SOFT_BCH; - nand->ecc.strength = 4; - nand->ecc.layout = NULL; - } else { - printf("Error: ECC strength %d not supported!\n", eccstrength); - } - - /* Update NAND handling after ECC mode switch */ - err = nand_scan_tail(mtd); - - return err; -} -#endif /* CONFIG_SPL_BUILD */ - int fsmc_nand_init(struct nand_chip *nand) { static int chip_nr; diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index a12e8f2702..eb6fe9f6b3 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -36,7 +36,6 @@ obj-$(CONFIG_USB_EHCI_OMAP) += ehci-omap.o obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o obj-$(CONFIG_USB_EHCI_MSM) += ehci-msm.o obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o -obj-$(CONFIG_USB_EHCI_SPEAR) += ehci-spear.o obj-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o obj-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o obj-$(CONFIG_USB_EHCI_VF) += ehci-vf.o diff --git a/drivers/usb/host/ehci-spear.c b/drivers/usb/host/ehci-spear.c deleted file mode 100644 index 3e87e0c7fd..0000000000 --- a/drivers/usb/host/ehci-spear.c +++ /dev/null @@ -1,77 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2010 - * Armando Visconti, ST Micoelectronics, . - * - * (C) Copyright 2009 - * Marvell Semiconductor - * Written-by: Prafulla Wadaskar - */ - -#include -#include -#include -#include -#include -#include "ehci.h" -#include -#include - -static void spear6xx_usbh_stop(void) -{ - struct misc_regs *const misc_p = - (struct misc_regs *)CONFIG_SPEAR_MISCBASE; - u32 periph1_rst = readl(misc_p->periph1_rst); - - periph1_rst |= PERIPH_USBH1 | PERIPH_USBH2; - writel(periph1_rst, misc_p->periph1_rst); - - udelay(1000); - periph1_rst &= ~(PERIPH_USBH1 | PERIPH_USBH2); - writel(periph1_rst, misc_p->periph1_rst); -} - -/* - * Create the appropriate control structures to manage - * a new EHCI host controller. - */ -int ehci_hcd_init(int index, enum usb_init_type init, - struct ehci_hccr **hccr, struct ehci_hcor **hcor) -{ - u32 ehci = 0; - - switch (index) { - case 0: - ehci = CONFIG_SYS_UHC0_EHCI_BASE; - break; - case 1: - ehci = CONFIG_SYS_UHC1_EHCI_BASE; - break; - default: - printf("ERROR: wrong controller index!\n"); - break; - }; - - *hccr = (struct ehci_hccr *)(ehci + 0x100); - *hcor = (struct ehci_hcor *)((uint32_t) *hccr + - HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); - - debug("SPEAr-ehci: init hccr %x and hcor %x hc_length %d\n", - (uint32_t)*hccr, (uint32_t)*hcor, - (uint32_t)HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); - - return 0; -} - -/* - * Destroy the appropriate control structures corresponding - * the the EHCI host controller. - */ -int ehci_hcd_stop(int index) -{ -#if defined(CONFIG_SPEAR600) - spear6xx_usbh_stop(); -#endif - - return 0; -} diff --git a/include/configs/spear-common.h b/include/configs/spear-common.h deleted file mode 100644 index d77ea6010a..0000000000 --- a/include/configs/spear-common.h +++ /dev/null @@ -1,162 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2009 - * Vipin Kumar, STMicroelectronics, - */ - -#ifndef _SPEAR_COMMON_H -#define _SPEAR_COMMON_H -/* - * Common configurations used for both spear3xx as well as spear6xx - */ - -/* U-Boot Load Address */ - -/* Ethernet driver configuration */ -#define CONFIG_PHY_RESET_DELAY 10000 /* in usec */ - -/* USBD driver configuration */ -#if defined(CONFIG_SPEAR_USBTTY) -#define CONFIG_DW_UDC -#define CONFIG_USB_DEVICE -#define CONFIG_USBD_HS -#define CONFIG_USB_TTY - -#define CONFIG_USBD_PRODUCT_NAME "SPEAr SoC" -#define CONFIG_USBD_MANUFACTURER "ST Microelectronics" - -#endif - -#define CONFIG_EXTRA_ENV_USBTTY "usbtty=cdc_acm\0" - -/* I2C driver configuration */ -#define CONFIG_SYS_I2C -#if defined(CONFIG_SPEAR600) -#define CONFIG_SYS_I2C_BASE 0xD0200000 -#endif -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x02 - -#define CONFIG_I2C_CHIPADDRESS 0x50 - -/* Timer, HZ specific defines */ - -/* Flash configuration */ -#if defined(CONFIG_FLASH_PNOR) -#define CONFIG_SPEAR_EMI -#else -#define CONFIG_ST_SMI -#endif - -#if defined(CONFIG_ST_SMI) - -#define CONFIG_SYS_MAX_FLASH_BANKS 2 -#define CONFIG_SYS_FLASH_BASE 0xF8000000 -#define CONFIG_SYS_CS1_FLASH_BASE 0xF9000000 -#define CONFIG_SYS_FLASH_BANK_SIZE 0x01000000 -#define CONFIG_SYS_FLASH_ADDR_BASE {CONFIG_SYS_FLASH_BASE, \ - CONFIG_SYS_CS1_FLASH_BASE} -#define CONFIG_SYS_MAX_FLASH_SECT 128 - -#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * CONFIG_SYS_HZ) -#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * CONFIG_SYS_HZ) - -#endif - -/* - * Serial Configuration (PL011) - * CONFIG_PL01x_PORTS is defined in specific files - */ -#define CONFIG_PL011_CLOCK (48 * 1000 * 1000) -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, \ - 57600, 115200 } - -#define CONFIG_SYS_LOADS_BAUD_CHANGE - -/* NAND FLASH Configuration */ -#define CONFIG_SYS_NAND_SELF_INIT -#define CONFIG_NAND_FSMC -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_ONFI_DETECTION - -/* - * Default Environment Varible definitions - */ - -/* - * U-Boot Environment placing definitions. - */ -#if defined(CONFIG_ENV_IS_IN_FLASH) -#ifdef CONFIG_ST_SMI -/* - * Environment is in serial NOR flash - */ -#define CONFIG_SYS_MONITOR_LEN 0x00040000 -#define CONFIG_FSMTDBLK "/dev/mtdblock3 " - -#define CONFIG_BOOTCOMMAND "bootm 0xf8050000" - -#elif defined(CONFIG_SPEAR_EMI) -/* - * Environment is in parallel NOR flash - */ -#define CONFIG_SYS_MONITOR_LEN 0x00060000 -#define CONFIG_FSMTDBLK "/dev/mtdblock3 " - -#define CONFIG_BOOTCOMMAND "cp.b 0x50080000 0x1600000 " \ - "0x4C0000; bootm 0x1600000" -#endif -#elif defined(CONFIG_ENV_IS_IN_NAND) -/* - * Environment is in NAND - */ - -#define CONFIG_ENV_RANGE 0x10000 -#define CONFIG_FSMTDBLK "/dev/mtdblock7 " - -#define CONFIG_BOOTCOMMAND "nand read.jffs2 0x1600000 " \ - "0x80000 0x4C0000; " \ - "bootm 0x1600000" -#endif - -#define CONFIG_NFSBOOTCOMMAND \ - "bootp; " \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):" \ - "$(netmask):$(hostname):$(netdev):off " \ - "console=ttyAMA0,115200 $(othbootargs);" \ - "bootm; " - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=ttyAMA0,115200 $(othbootargs);" \ - CONFIG_BOOTCOMMAND - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - -/* Miscellaneous configurable options */ -#define CONFIG_BOOT_PARAMS_ADDR 0x00000100 -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS - -#define CONFIG_SYS_MALLOC_LEN (1024*1024) -#define CONFIG_SYS_LOAD_ADDR 0x00800000 - -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Physical Memory Map */ -#define PHYS_SDRAM_1 0x00000000 -#define PHYS_SDRAM_1_MAXSIZE 0x40000000 - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xD2800000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -#endif diff --git a/include/configs/spear6xx_evb.h b/include/configs/spear6xx_evb.h deleted file mode 100644 index 4fedc9efce..0000000000 --- a/include/configs/spear6xx_evb.h +++ /dev/null @@ -1,36 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * (C) Copyright 2009 - * Vipin Kumar, STMicroelectronics, - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#if defined(CONFIG_USBTTY) -#define CONFIG_SPEAR_USBTTY -#endif - -#include - -/* Serial Configuration (PL011) */ -#define CONFIG_SYS_SERIAL0 0xD0000000 -#define CONFIG_SYS_SERIAL1 0xD0080000 -#define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, \ - (void *)CONFIG_SYS_SERIAL1 } - -/* NAND flash configuration */ -#define CONFIG_SYS_FSMC_NAND_SP -#define CONFIG_SYS_FSMC_NAND_8BIT -#define CONFIG_SYS_NAND_BASE 0xD2000000 - -/* Ethernet PHY configuration */ - -/* Environment Settings */ -#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_EXTRA_ENV_USBTTY - -#endif /* __CONFIG_H */ diff --git a/include/configs/x600.h b/include/configs/x600.h deleted file mode 100644 index 0dd5722794..0000000000 --- a/include/configs/x600.h +++ /dev/null @@ -1,228 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2009, STMicroelectronics - All Rights Reserved - * Author(s): Vipin Kumar, for STMicroelectronics. - * - * Copyright (C) 2012, 2015 Stefan Roese - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_SPEAR600 /* SPEAr600 SoC */ -#define CONFIG_X600 /* on X600 board */ - -#include - -/* Timer, HZ specific defines */ -#define CONFIG_SYS_HZ_CLOCK 8300000 - -#define CONFIG_SYS_FLASH_BASE 0xf8000000 -/* Reserve 8KiB for SPL */ -#define CONFIG_SPL_PAD_TO 8192 /* decimal for 'dd' */ -#define CONFIG_SYS_SPL_LEN CONFIG_SPL_PAD_TO -#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + \ - CONFIG_SYS_SPL_LEN) -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN 0x60000 - -/* Serial Configuration (PL011) */ -#define CONFIG_SYS_SERIAL0 0xD0000000 -#define CONFIG_SYS_SERIAL1 0xD0080000 -#define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, \ - (void *)CONFIG_SYS_SERIAL1 } -#define CONFIG_PL011_CLOCK (48 * 1000 * 1000) -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, \ - 57600, 115200 } -#define CONFIG_SYS_LOADS_BAUD_CHANGE - -/* NOR FLASH config options */ -#define CONFIG_ST_SMI -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_FLASH_BANK_SIZE 0x01000000 -#define CONFIG_SYS_FLASH_ADDR_BASE { CONFIG_SYS_FLASH_BASE } -#define CONFIG_SYS_MAX_FLASH_SECT 128 -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * CONFIG_SYS_HZ) -#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * CONFIG_SYS_HZ) - -/* NAND FLASH config options */ -#define CONFIG_NAND_FSMC -#define CONFIG_SYS_NAND_SELF_INIT -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE CONFIG_FSMC_NAND_BASE -#define CONFIG_MTD_ECC_SOFT -#define CONFIG_SYS_FSMC_NAND_8BIT -#define CONFIG_SYS_NAND_ONFI_DETECTION -#define CONFIG_NAND_ECC_BCH - -/* UBI/UBI config options */ - -/* Ethernet config options */ -#define CONFIG_PHY_RESET_DELAY 10000 /* in usec */ - -#define CONFIG_SPEAR_GPIO - -/* I2C config options */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_BASE 0xD0200000 -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x02 -#define CONFIG_I2C_CHIPADDRESS 0x50 - -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* FPGA config options */ -#define CONFIG_FPGA_COUNT 1 - -/* USB EHCI options */ -#define CONFIG_USB_EHCI_SPEAR -#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 - -/* - * U-Boot Environment placing definitions. - */ - -/* Miscellaneous configurable options */ -#define CONFIG_BOOT_PARAMS_ADDR 0x00000100 -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS - -#define CONFIG_SYS_MALLOC_LEN (8 << 20) -#define CONFIG_SYS_LOAD_ADDR 0x00800000 - -#define CONFIG_HOSTNAME "x600" -#define CONFIG_UBI_PART ubi0 -#define CONFIG_UBIFS_VOLUME rootfs - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "u-boot_addr=1000000\0" \ - "u-boot=" CONFIG_HOSTNAME "/u-boot.spr\0" \ - "load=tftp ${u-boot_addr} ${u-boot}\0" \ - "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ - " +${filesize};" \ - "erase " __stringify(CONFIG_SYS_MONITOR_BASE) " +${filesize};" \ - "cp.b ${u-boot_addr} " __stringify(CONFIG_SYS_MONITOR_BASE) \ - " ${filesize};" \ - "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \ - " +${filesize}\0" \ - "upd=run load update\0" \ - "ubifs=" CONFIG_HOSTNAME "/ubifs.img\0" \ - "part=" __stringify(CONFIG_UBI_PART) "\0" \ - "vol=" __stringify(CONFIG_UBIFS_VOLUME) "\0" \ - "load_ubifs=tftp ${kernel_addr} ${ubifs}\0" \ - "update_ubifs=ubi part ${part};ubi write ${kernel_addr} ${vol}" \ - " ${filesize}\0" \ - "upd_ubifs=run load_ubifs update_ubifs\0" \ - "init_ubifs=nand erase.part ubi0;ubi part ${part};" \ - "ubi create ${vol} 4000000\0" \ - "netdev=eth0\0" \ - "rootpath=/opt/eldk-4.2/arm\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "boot_part=0\0" \ - "altbootcmd=if test $boot_part -eq 0;then " \ - "echo Switching to partition 1!;" \ - "setenv boot_part 1;" \ - "else; " \ - "echo Switching to partition 0!;" \ - "setenv boot_part 0;" \ - "fi;" \ - "saveenv;boot\0" \ - "ubifsargs=set bootargs ubi.mtd=ubi${boot_part} " \ - "root=ubi0:rootfs rootfstype=ubifs\0" \ - "kernel=" CONFIG_HOSTNAME "/uImage\0" \ - "kernel_fs=/boot/uImage \0" \ - "kernel_addr=1000000\0" \ - "dtb=" CONFIG_HOSTNAME "/" \ - CONFIG_HOSTNAME ".dtb\0" \ - "dtb_fs=/boot/" CONFIG_HOSTNAME ".dtb\0" \ - "dtb_addr=1800000\0" \ - "load_kernel=tftp ${kernel_addr} ${kernel}\0" \ - "load_dtb=tftp ${dtb_addr} ${dtb}\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addcon=setenv bootargs ${bootargs} console=ttyAMA0," \ - "${baudrate}\0" \ - "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ - "net_nfs=run load_dtb load_kernel; " \ - "run nfsargs addip addcon addmtd addmisc;" \ - "bootm ${kernel_addr} - ${dtb_addr}\0" \ - "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ - "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ - "nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip" \ - " addcon addmisc addmtd;" \ - "bootm ${kernel_addr} - ${dtb_addr}\0" \ - "ubifs_mount=ubi part ubi${boot_part};ubifsmount ubi:rootfs\0" \ - "ubifs_load=ubifsload ${kernel_addr} ${kernel_fs};" \ - "ubifsload ${dtb_addr} ${dtb_fs};\0" \ - "nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip addcon " \ - "addmtd addmisc;bootm ${kernel_addr} - ${dtb_addr}\0" \ - "bootcmd=run nand_ubifs\0" \ - "\0" - -/* Physical Memory Map */ -#define PHYS_SDRAM_1 0x00000000 -#define PHYS_SDRAM_1_MAXSIZE 0x40000000 - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SRAM_BASE 0xd2800000 -/* Preserve the last 2 lwords for the boot-counter */ -#define CONFIG_SRAM_SIZE ((8 << 10) - 0x8) -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SRAM_BASE -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SRAM_SIZE - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* - * SPL related defines - */ -#define CONFIG_SPL_MAX_SIZE (CONFIG_SRAM_SIZE - 0xb00) -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/spear" - -/* - * Please select/define only one of the following - * Each definition corresponds to a supported DDR chip. - * DDR configuration is based on the following selection - */ -#define CONFIG_DDR_MT47H64M16 1 -#define CONFIG_DDR_MT47H32M16 0 -#define CONFIG_DDR_MT47H128M8 0 - -/* - * Synchronous/Asynchronous operation of DDR - * - * Select CONFIG_DDR_2HCLK for DDR clk = 333MHz, synchronous operation - * Select CONFIG_DDR_HCLK for DDR clk = 166MHz, synchronous operation - * Select CONFIG_DDR_PLL2 for DDR clk = PLL2, asynchronous operation - */ -#define CONFIG_DDR_2HCLK 1 -#define CONFIG_DDR_HCLK 0 -#define CONFIG_DDR_PLL2 0 - -/* - * xxx_BOOT_SUPPORTED macro defines whether a booting type is supported - * or not. Modify/Add to only these macros to define new boot types - */ -#define USB_BOOT_SUPPORTED 0 -#define PCIE_BOOT_SUPPORTED 0 -#define SNOR_BOOT_SUPPORTED 1 -#define NAND_BOOT_SUPPORTED 1 -#define PNOR_BOOT_SUPPORTED 0 -#define TFTP_BOOT_SUPPORTED 0 -#define UART_BOOT_SUPPORTED 0 -#define SPI_BOOT_SUPPORTED 0 -#define I2C_BOOT_SUPPORTED 0 -#define MMC_BOOT_SUPPORTED 0 - -#endif /* __CONFIG_H */