From: Adam Ford Date: Wed, 10 Jul 2019 18:59:10 +0000 (-0500) Subject: usb: musb-new: Add support for da8xx-musb X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=5608331d813630120871d04847b59628ec59f7f9;p=u-boot.git usb: musb-new: Add support for da8xx-musb With the recently added phy driver, this patch will enable the musb driver on the da8xx to operate in host mode. Signed-off-by: Adam Ford --- diff --git a/drivers/usb/musb-new/Kconfig b/drivers/usb/musb-new/Kconfig index 75005ccdd1..79ad14ef66 100644 --- a/drivers/usb/musb-new/Kconfig +++ b/drivers/usb/musb-new/Kconfig @@ -18,6 +18,14 @@ config USB_MUSB_GADGET help Enables the MUSB USB dual-role controller in gadget mode. +config USB_MUSB_DA8XX + bool "Enable DA8xx MUSB Controller" + depends on DM_USB + help + Say y here to enable support for the dual role high + speed USB controller based on the Mentor Graphics + silicon IP. + config USB_MUSB_TI bool "Enable TI OTG USB controller" depends on DM_USB diff --git a/drivers/usb/musb-new/Makefile b/drivers/usb/musb-new/Makefile index 4eca0e5631..ec7852ce94 100644 --- a/drivers/usb/musb-new/Makefile +++ b/drivers/usb/musb-new/Makefile @@ -6,6 +6,7 @@ obj-$(CONFIG_USB_MUSB_GADGET) += musb_gadget.o musb_gadget_ep0.o musb_core.o obj-$(CONFIG_USB_MUSB_GADGET) += musb_uboot.o obj-$(CONFIG_USB_MUSB_HOST) += musb_host.o musb_core.o musb_uboot.o obj-$(CONFIG_USB_MUSB_DSPS) += musb_dsps.o +obj-$(CONFIG_USB_MUSB_DA8XX) += da8xx.o obj-$(CONFIG_USB_MUSB_AM35X) += am35x.o obj-$(CONFIG_USB_MUSB_OMAP2PLUS) += omap2430.o obj-$(CONFIG_USB_MUSB_PIC32) += pic32.o diff --git a/drivers/usb/musb-new/da8xx.c b/drivers/usb/musb-new/da8xx.c new file mode 100644 index 0000000000..899b30db68 --- /dev/null +++ b/drivers/usb/musb-new/da8xx.c @@ -0,0 +1,350 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Texas Instruments da8xx "glue layer" + * + * Copyright (c) 2019, by Texas Instruments + * + * Based on the DA8xx "glue layer" code. + * Copyright (c) 2008-2019, MontaVista Software, Inc. + * + * DT support + * Copyright (c) 2016 Petr Kulhavy + * This file is part of the Inventra Controller Driver for Linux. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "linux-compat.h" +#include "musb_core.h" +#include "musb_uboot.h" + +/* USB 2.0 OTG module registers */ +#define DA8XX_USB_REVISION_REG 0x00 +#define DA8XX_USB_CTRL_REG 0x04 +#define DA8XX_USB_STAT_REG 0x08 +#define DA8XX_USB_EMULATION_REG 0x0c +#define DA8XX_USB_SRP_FIX_TIME_REG 0x18 +#define DA8XX_USB_INTR_SRC_REG 0x20 +#define DA8XX_USB_INTR_SRC_SET_REG 0x24 +#define DA8XX_USB_INTR_SRC_CLEAR_REG 0x28 +#define DA8XX_USB_INTR_MASK_REG 0x2c +#define DA8XX_USB_INTR_MASK_SET_REG 0x30 +#define DA8XX_USB_INTR_MASK_CLEAR_REG 0x34 +#define DA8XX_USB_INTR_SRC_MASKED_REG 0x38 +#define DA8XX_USB_END_OF_INTR_REG 0x3c +#define DA8XX_USB_GENERIC_RNDIS_EP_SIZE_REG(n) (0x50 + (((n) - 1) << 2)) + +/* Control register bits */ +#define DA8XX_SOFT_RESET_MASK 1 + +#define DA8XX_USB_TX_EP_MASK 0x1f /* EP0 + 4 Tx EPs */ +#define DA8XX_USB_RX_EP_MASK 0x1e /* 4 Rx EPs */ + +/* USB interrupt register bits */ +#define DA8XX_INTR_USB_SHIFT 16 +#define DA8XX_INTR_USB_MASK (0x1ff << DA8XX_INTR_USB_SHIFT) /* 8 Mentor */ + /* interrupts and DRVVBUS interrupt */ +#define DA8XX_INTR_DRVVBUS 0x100 +#define DA8XX_INTR_RX_SHIFT 8 +#define DA8XX_INTR_RX_MASK (DA8XX_USB_RX_EP_MASK << DA8XX_INTR_RX_SHIFT) +#define DA8XX_INTR_TX_SHIFT 0 +#define DA8XX_INTR_TX_MASK (DA8XX_USB_TX_EP_MASK << DA8XX_INTR_TX_SHIFT) + +#define DA8XX_MENTOR_CORE_OFFSET 0x400 + +static irqreturn_t da8xx_musb_interrupt(int irq, void *hci) +{ + struct musb *musb = hci; + void __iomem *reg_base = musb->ctrl_base; + unsigned long flags; + irqreturn_t ret = IRQ_NONE; + u32 status; + + spin_lock_irqsave(&musb->lock, flags); + + /* + * NOTE: DA8XX shadows the Mentor IRQs. Don't manage them through + * the Mentor registers (except for setup), use the TI ones and EOI. + */ + + /* Acknowledge and handle non-CPPI interrupts */ + status = musb_readl(reg_base, DA8XX_USB_INTR_SRC_MASKED_REG); + if (!status) + goto eoi; + + musb_writel(reg_base, DA8XX_USB_INTR_SRC_CLEAR_REG, status); + dev_dbg(musb->controller, "USB IRQ %08x\n", status); + + musb->int_rx = (status & DA8XX_INTR_RX_MASK) >> DA8XX_INTR_RX_SHIFT; + musb->int_tx = (status & DA8XX_INTR_TX_MASK) >> DA8XX_INTR_TX_SHIFT; + musb->int_usb = (status & DA8XX_INTR_USB_MASK) >> DA8XX_INTR_USB_SHIFT; + + /* + * DRVVBUS IRQs are the only proxy we have (a very poor one!) for + * DA8xx's missing ID change IRQ. We need an ID change IRQ to + * switch appropriately between halves of the OTG state machine. + * Managing DEVCTL.Session per Mentor docs requires that we know its + * value but DEVCTL.BDevice is invalid without DEVCTL.Session set. + * Also, DRVVBUS pulses for SRP (but not at 5 V)... + */ + if (status & (DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT)) { + int drvvbus = musb_readl(reg_base, DA8XX_USB_STAT_REG); + void __iomem *mregs = musb->mregs; + u8 devctl = musb_readb(mregs, MUSB_DEVCTL); + int err; + + err = musb->int_usb & MUSB_INTR_VBUSERROR; + if (err) { + /* + * The Mentor core doesn't debounce VBUS as needed + * to cope with device connect current spikes. This + * means it's not uncommon for bus-powered devices + * to get VBUS errors during enumeration. + * + * This is a workaround, but newer RTL from Mentor + * seems to allow a better one: "re"-starting sessions + * without waiting for VBUS to stop registering in + * devctl. + */ + musb->int_usb &= ~MUSB_INTR_VBUSERROR; + WARNING("VBUS error workaround (delay coming)\n"); + } else if (drvvbus) { + MUSB_HST_MODE(musb); + musb->port1_status |= USB_PORT_STAT_POWER; + } else if (!(musb->int_usb & MUSB_INTR_BABBLE)) { + /* + * When babble condition happens, drvvbus interrupt + * is also generated. Ignore this drvvbus interrupt + * and let babble interrupt handler recovers the + * controller; otherwise, the host-mode flag is lost + * due to the MUSB_DEV_MODE() call below and babble + * recovery logic will not be called. + */ + musb->is_active = 0; + MUSB_DEV_MODE(musb); + musb->port1_status &= ~USB_PORT_STAT_POWER; + } + ret = IRQ_HANDLED; + } + + if (musb->int_tx || musb->int_rx || musb->int_usb) + ret |= musb_interrupt(musb); +eoi: + /* EOI needs to be written for the IRQ to be re-asserted. */ + if (ret == IRQ_HANDLED || status) + musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0); + + spin_unlock_irqrestore(&musb->lock, flags); + + return ret; +} + +static int da8xx_musb_init(struct musb *musb) +{ + u32 revision; + void __iomem *reg_base = musb->ctrl_base; + + int ret; + + /* reset the controller */ + writel(0x1, &da8xx_usb_regs->control); + udelay(50); + + /* Returns zero if e.g. not clocked */ + revision = readl(&da8xx_usb_regs->revision); + if (revision == 0) + return -ENODEV; + + /* Disable all interrupts */ + writel((DA8XX_USB_USBINT_MASK | DA8XX_USB_TXINT_MASK | + DA8XX_USB_RXINT_MASK), &da8xx_usb_regs->intmsk_set); + + musb->mregs += DA8XX_MENTOR_CORE_OFFSET; + + /* NOTE: IRQs are in mixed mode, not bypass to pure MUSB */ + debug("DA8xx OTG revision %08x, control %02x\n", revision, + musb_readb(reg_base, DA8XX_USB_CTRL_REG)); + + musb->isr = da8xx_musb_interrupt; + return 0; +} + +static int da8xx_musb_exit(struct musb *musb) +{ + /* flush any interrupts */ + writel((DA8XX_USB_USBINT_MASK | DA8XX_USB_TXINT_MASK | + DA8XX_USB_RXINT_MASK), &da8xx_usb_regs->intmsk_clr); + writel(0, &da8xx_usb_regs->eoi); + + return 0; +} + +/** + * da8xx_musb_enable - enable interrupts + */ +static int da8xx_musb_enable(struct musb *musb) +{ + void __iomem *reg_base = musb->ctrl_base; + u32 mask; + + /* Workaround: setup IRQs through both register sets. */ + mask = ((musb->epmask & DA8XX_USB_TX_EP_MASK) << DA8XX_INTR_TX_SHIFT) | + ((musb->epmask & DA8XX_USB_RX_EP_MASK) << DA8XX_INTR_RX_SHIFT) | + DA8XX_INTR_USB_MASK; + musb_writel(reg_base, DA8XX_USB_INTR_MASK_SET_REG, mask); + + /* Force the DRVVBUS IRQ so we can start polling for ID change. */ + musb_writel(reg_base, DA8XX_USB_INTR_SRC_SET_REG, + DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT); + + return 0; +} + +/** + * da8xx_musb_disable - disable HDRC and flush interrupts + */ +static void da8xx_musb_disable(struct musb *musb) +{ + void __iomem *reg_base = musb->ctrl_base; + + musb_writel(reg_base, DA8XX_USB_INTR_MASK_CLEAR_REG, + DA8XX_INTR_USB_MASK | + DA8XX_INTR_TX_MASK | DA8XX_INTR_RX_MASK); + musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0); +} + +void da8xx_musb_reset(struct udevice *dev) +{ + void *reg_base = dev_read_addr_ptr(dev); + + /* Reset the controller */ + musb_writel(reg_base, DA8XX_USB_CTRL_REG, DA8XX_SOFT_RESET_MASK); +} + +void da8xx_musb_clear_irq(struct udevice *dev) +{ + /* flush any interrupts */ + writel((DA8XX_USB_USBINT_MASK | DA8XX_USB_TXINT_MASK | + DA8XX_USB_RXINT_MASK), &da8xx_usb_regs->intmsk_clr); + writel(0, &da8xx_usb_regs->eoi); +} + +const struct musb_platform_ops da8xx_ops = { + .init = da8xx_musb_init, + .exit = da8xx_musb_exit, + .enable = da8xx_musb_enable, + .disable = da8xx_musb_disable, +}; + +struct da8xx_musb_platdata { + void *base; + void *ctrl_mod_base; + struct musb_hdrc_platform_data plat; + struct musb_hdrc_config musb_config; + struct omap_musb_board_data otg_board_data; + struct phy phy; +}; + +static int da8xx_musb_ofdata_to_platdata(struct udevice *dev) +{ + struct da8xx_musb_platdata *platdata = dev_get_platdata(dev); + const void *fdt = gd->fdt_blob; + int node = dev_of_offset(dev); + + platdata->base = (void *)dev_read_addr_ptr(dev); + platdata->musb_config.multipoint = 1; + platdata->musb_config.dyn_fifo = 1; + platdata->musb_config.num_eps = 5; + platdata->musb_config.ram_bits = 10; + platdata->plat.power = fdtdec_get_int(fdt, node, "power", 50); + platdata->otg_board_data.interface_type = MUSB_INTERFACE_UTMI; + platdata->plat.mode = MUSB_HOST; + platdata->otg_board_data.dev = dev; + platdata->plat.config = &platdata->musb_config; + platdata->plat.platform_ops = &da8xx_ops; + platdata->plat.board_data = &platdata->otg_board_data; + platdata->otg_board_data.clear_irq = da8xx_musb_clear_irq; + platdata->otg_board_data.reset = da8xx_musb_reset; + return 0; +} + +static int da8xx_musb_probe(struct udevice *dev) +{ + struct musb_host_data *host = dev_get_priv(dev); + struct da8xx_musb_platdata *platdata = dev_get_platdata(dev); + struct usb_bus_priv *priv = dev_get_uclass_priv(dev); + struct omap_musb_board_data *otg_board_data; + int ret; + void *base = dev_read_addr_ptr(dev); + + /* Get the phy info from the device tree */ + ret = generic_phy_get_by_name(dev, "usb-phy", &platdata->phy); + if (ret) + return ret; + + /* Initialize the phy */ + ret = generic_phy_init(&platdata->phy); + if (ret) + return ret; + + /* enable psc for usb2.0 */ + lpsc_on(33); + + /* Enable phy */ + generic_phy_power_on(&platdata->phy); + + priv->desc_before_addr = true; + otg_board_data = &platdata->otg_board_data; + + host->host = musb_init_controller(&platdata->plat, + (struct device *)otg_board_data, + platdata->base); + if (!host->host) { + ret = -ENODEV; + goto shutdown; /* Shutdown what we started */ + } + + ret = musb_lowlevel_init(host); + + if (ret == 0) + return 0; +shutdown: + /* Turn off the phy if we fail */ + generic_phy_power_off(&platdata->phy); + lpsc_disable(33); + return ret; +} + +static int da8xx_musb_remove(struct udevice *dev) +{ + struct musb_host_data *host = dev_get_priv(dev); + + musb_stop(host->host); + + return 0; +} + +static const struct udevice_id da8xx_musb_ids[] = { + { .compatible = "ti,da830-musb" }, + { } +}; + +U_BOOT_DRIVER(da8xx_musb) = { + .name = "da8xx-musb", + .id = UCLASS_USB, + .of_match = da8xx_musb_ids, + .ofdata_to_platdata = da8xx_musb_ofdata_to_platdata, + .probe = da8xx_musb_probe, + .remove = da8xx_musb_remove, + .ops = &musb_usb_ops, + .platdata_auto_alloc_size = sizeof(struct da8xx_musb_platdata), + .priv_auto_alloc_size = sizeof(struct musb_host_data), +};