From: Simon Glass Date: Mon, 15 Mar 2021 05:00:31 +0000 (+1300) Subject: x86: coral: Allow init of debug UART in U-Boot proper X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=51de94dfe497b150c066788a38e93bd989ae7552;p=u-boot.git x86: coral: Allow init of debug UART in U-Boot proper At present the debug UART is only set up in SPL, on the assumption that the boot flow will always pass through there. When booting from coreboot, SPL is not used, so the debug UART is not available. Move the code into a common place so that it can be used in U-Boot proper also. Add the required init to start_from_spl.S as well. Signed-off-by: Simon Glass --- diff --git a/arch/x86/cpu/apollolake/cpu_common.c b/arch/x86/cpu/apollolake/cpu_common.c index 63f6999b02..5d7d26b140 100644 --- a/arch/x86/cpu/apollolake/cpu_common.c +++ b/arch/x86/cpu/apollolake/cpu_common.c @@ -7,11 +7,17 @@ #include #include #include +#include #include +#include #include #include +#include #include +/* Define this here to avoid referencing any drivers for the debug UART 1 */ +#define PCH_DEV_P2SB PCI_BDF(0, 0x0d, 0) + void cpu_flush_l1d_to_l2(void) { struct msr_t msr; @@ -40,3 +46,57 @@ void enable_pm_timer_emulation(const struct udevice *pmc) debug("PM timer %x %x\n", msr.hi, msr.lo); msr_write(MSR_EMULATE_PM_TIMER, msr); } + +static void pch_uart_init(void) +{ + /* + * Set up the pinmux so that the UART rx/tx signals are connected + * outside the SoC. + * + * There are about 500 lines of code required to program the GPIO + * configuration for the UARTs. But it boils down to four writes, and + * for the debug UART we want the minimum possible amount of code before + * the UART is running. So just add the magic writes here. See + * apl_hostbridge_early_init_pinctrl() for the full horror. + */ + if (PCI_FUNC(PCH_DEV_UART) == 1) { + writel(0x40000402, 0xd0c50650); + writel(0x3c47, 0xd0c50654); + writel(0x40000400, 0xd0c50658); + writel(0x3c48, 0xd0c5065c); + } else { /* UART2 */ + writel(0x40000402, 0xd0c50670); + writel(0x3c4b, 0xd0c50674); + writel(0x40000400, 0xd0c50678); + writel(0x3c4c, 0xd0c5067c); + } + +#ifdef CONFIG_DEBUG_UART + apl_uart_init(PCH_DEV_UART, CONFIG_DEBUG_UART_BASE); +#endif +} + +static void p2sb_enable_bar(ulong bar) +{ + /* Enable PCR Base address in PCH */ + pci_x86_write_config(PCH_DEV_P2SB, PCI_BASE_ADDRESS_0, bar, + PCI_SIZE_32); + pci_x86_write_config(PCH_DEV_P2SB, PCI_BASE_ADDRESS_1, 0, PCI_SIZE_32); + + /* Enable P2SB MSE */ + pci_x86_write_config(PCH_DEV_P2SB, PCI_COMMAND, + PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY, + PCI_SIZE_8); +} + +/* + * board_debug_uart_init() - Init the debug UART ready for use + * + * This is the minimum init needed to get the UART running. It avoids any + * drivers or complex code, so that the UART is running as soon as possible. + */ +void board_debug_uart_init(void) +{ + p2sb_enable_bar(IOMAP_P2SB_BAR); + pch_uart_init(); +} diff --git a/arch/x86/cpu/apollolake/cpu_spl.c b/arch/x86/cpu/apollolake/cpu_spl.c index 9a18476b22..8f48457ee2 100644 --- a/arch/x86/cpu/apollolake/cpu_spl.c +++ b/arch/x86/cpu/apollolake/cpu_spl.c @@ -31,68 +31,10 @@ #include #include #include -#include #include #include #include -/* Define this here to avoid referencing any drivers for the debug UART 1 */ -#define PCH_DEV_P2SB PCI_BDF(0, 0x0d, 0) - -static void pch_uart_init(void) -{ - /* - * Set up the pinmux so that the UART rx/tx signals are connected - * outside the SoC. - * - * There are about 500 lines of code required to program the GPIO - * configuration for the UARTs. But it boils down to four writes, and - * for the debug UART we want the minimum possible amount of code before - * the UART is running. So just add the magic writes here. See - * apl_hostbridge_early_init_pinctrl() for the full horror. - */ - if (PCI_FUNC(PCH_DEV_UART) == 1) { - writel(0x40000402, 0xd0c50650); - writel(0x3c47, 0xd0c50654); - writel(0x40000400, 0xd0c50658); - writel(0x3c48, 0xd0c5065c); - } else { /* UART2 */ - writel(0x40000402, 0xd0c50670); - writel(0x3c4b, 0xd0c50674); - writel(0x40000400, 0xd0c50678); - writel(0x3c4c, 0xd0c5067c); - } - -#ifdef CONFIG_DEBUG_UART - apl_uart_init(PCH_DEV_UART, CONFIG_DEBUG_UART_BASE); -#endif -} - -static void p2sb_enable_bar(ulong bar) -{ - /* Enable PCR Base address in PCH */ - pci_x86_write_config(PCH_DEV_P2SB, PCI_BASE_ADDRESS_0, bar, - PCI_SIZE_32); - pci_x86_write_config(PCH_DEV_P2SB, PCI_BASE_ADDRESS_1, 0, PCI_SIZE_32); - - /* Enable P2SB MSE */ - pci_x86_write_config(PCH_DEV_P2SB, PCI_COMMAND, - PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY, - PCI_SIZE_8); -} - -/* - * board_debug_uart_init() - Init the debug UART ready for use - * - * This is the minimum init needed to get the UART running. It avoids any - * drivers or complex code, so that the UART is running as soon as possible. - */ -void board_debug_uart_init(void) -{ - p2sb_enable_bar(IOMAP_P2SB_BAR); - pch_uart_init(); -} - static int fast_spi_cache_bios_region(void) { uint map_size, offset; diff --git a/arch/x86/cpu/start_from_spl.S b/arch/x86/cpu/start_from_spl.S index 905c825cdc..abfd4abb62 100644 --- a/arch/x86/cpu/start_from_spl.S +++ b/arch/x86/cpu/start_from_spl.S @@ -43,6 +43,10 @@ use_existing_stack: call board_init_f_init_reserve +#ifdef CONFIG_DEBUG_UART + call debug_uart_init +#endif + call x86_cpu_reinit_f xorl %eax, %eax call board_init_f diff --git a/arch/x86/include/asm/arch-apollolake/uart.h b/arch/x86/include/asm/arch-apollolake/uart.h index 38335b0490..c3ca171b83 100644 --- a/arch/x86/include/asm/arch-apollolake/uart.h +++ b/arch/x86/include/asm/arch-apollolake/uart.h @@ -6,6 +6,7 @@ #ifndef _ASM_ARCH_UART_H #define _ASM_ARCH_UART_H +#include #include /**