From: Marcel Ziswiler Date: Thu, 21 Jul 2022 13:43:37 +0000 (+0200) Subject: imx8mn: synchronise device tree with linux X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=4e5114daf9eb327abd3e0d63654732dfb61474f2;p=u-boot.git imx8mn: synchronise device tree with linux Synchronise device tree with linux v5.19-rc5. Signed-off-by: Marcel Ziswiler --- diff --git a/arch/arm/dts/imx8mn-beacon-baseboard.dtsi b/arch/arm/dts/imx8mn-beacon-baseboard.dtsi index 376ca8ff72..02f37dcda7 100644 --- a/arch/arm/dts/imx8mn-beacon-baseboard.dtsi +++ b/arch/arm/dts/imx8mn-beacon-baseboard.dtsi @@ -126,7 +126,6 @@ compatible = "wlf,wm8962"; reg = <0x1a>; clocks = <&clk IMX8MN_CLK_SAI3_ROOT>; - clock-names = "xclk"; DCVDD-supply = <®_audio>; DBVDD-supply = <®_audio>; AVDD-supply = <®_audio>; @@ -176,6 +175,7 @@ pinctrl-0 = <&pinctrl_uart3>; assigned-clocks = <&clk IMX8MN_CLK_UART3>; assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>; + uart-has-rtscts; status = "okay"; }; @@ -259,6 +259,8 @@ fsl,pins = < MX8MN_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x40 MX8MN_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x40 + MX8MN_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x40 + MX8MN_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x40 >; }; diff --git a/arch/arm/dts/imx8mn-beacon-som.dtsi b/arch/arm/dts/imx8mn-beacon-som.dtsi index de2cd0e320..1133cded9b 100644 --- a/arch/arm/dts/imx8mn-beacon-som.dtsi +++ b/arch/arm/dts/imx8mn-beacon-som.dtsi @@ -101,7 +101,7 @@ #size-cells = <1>; compatible = "jedec,spi-nor"; spi-max-frequency = <80000000>; - spi-tx-bus-width = <4>; + spi-tx-bus-width = <1>; spi-rx-bus-width = <4>; }; }; @@ -120,6 +120,9 @@ interrupt-parent = <&gpio1>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; rohm,reset-snvs-powered; + #clock-cells = <0>; + clocks = <&osc_32k 0>; + clock-output-names = "clk-32k-out"; regulators { buck1_reg: BUCK1 { @@ -262,12 +265,15 @@ &usdhc1 { #address-cells = <1>; #size-cells = <0>; - pinctrl-names = "default"; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + vmmc-supply = <&buck4_reg>; + vqmmc-supply = <&buck5_reg>; bus-width = <4>; non-removable; cap-power-off-card; - pm-ignore-notify; keep-power-in-suspend; mmc-pwrseq = <&usdhc1_pwrseq>; status = "okay"; diff --git a/arch/arm/dts/imx8mn-bsh-smm-s2-common.dtsi b/arch/arm/dts/imx8mn-bsh-smm-s2-common.dtsi index 184c715bd3..c11895d9d5 100644 --- a/arch/arm/dts/imx8mn-bsh-smm-s2-common.dtsi +++ b/arch/arm/dts/imx8mn-bsh-smm-s2-common.dtsi @@ -4,6 +4,8 @@ * Copyright 2021 BSH Hausgeraete GmbH */ +/dts-v1/; + #include "imx8mn.dtsi" / { @@ -11,17 +13,17 @@ stdout-path = &uart4; }; - fec_supply: fec_supply_en { + fec_supply: fec-supply-en { compatible = "regulator-fixed"; + vin-supply = <&buck4_reg>; regulator-name = "tja1101_en"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; - vin-supply = <&buck4_reg>; enable-active-high; }; - usdhc2_pwrseq: usdhc2_pwrseq { + usdhc2_pwrseq: usdhc2-pwrseq { compatible = "mmc-pwrseq-simple"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc2_pwrseq>; @@ -57,8 +59,6 @@ phy-mode = "rmii"; phy-handle = <ðphy0>; phy-supply = <&fec_supply>; - phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; - phy-reset-duration = <20>; fsl,magic-packet; status = "okay"; @@ -69,6 +69,9 @@ ethphy0: ethernet-phy@0 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <0>; + reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; + reset-assert-us = <20>; + reset-deassert-us = <2000>; }; }; }; @@ -280,6 +283,14 @@ }; &iomuxc { + pinctrl_bluetooth: bluetoothgrp { + fsl,pins = < + MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x044 /* BT_REG_ON */ + MX8MN_IOMUXC_ENET_TD3_GPIO1_IO18 0x046 /* BT_DEV_WAKE */ + MX8MN_IOMUXC_ENET_RD2_GPIO1_IO28 0x090 /* BT_HOST_WAKE */ + >; + }; + pinctrl_espi2: espi2grp { fsl,pins = < MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x082 @@ -289,6 +300,26 @@ >; }; + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x002 + MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x002 + MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x090 + MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x090 + MX8MN_IOMUXC_ENET_RXC_ENET1_RX_ER 0x090 + MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x016 + MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x016 + MX8MN_IOMUXC_ENET_TD2_ENET1_TX_CLK 0x016 + MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x016 + MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x090 + MX8MN_IOMUXC_ENET_TXC_ENET1_TX_ER 0x016 + MX8MN_IOMUXC_SD2_CD_B_GPIO2_IO12 0x150 /* RMII_INT - ENET_INT */ + MX8MN_IOMUXC_SD2_WP_GPIO2_IO20 0x150 /* RMII_EN - ENET_EN */ + MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x016 /* RMII_WAKE - GPIO_ENET_WAKE */ + MX8MN_IOMUXC_ENET_RD3_GPIO1_IO29 0x016 /* RMII_RESET - GPIO_ENET_RST */ + >; + }; + pinctrl_i2c1: i2c1grp { fsl,pins = < MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400000c2 @@ -316,16 +347,26 @@ >; }; - pinctrl_uart4: uart4grp { + pinctrl_uart2: uart2grp { fsl,pins = < - MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX 0x040 - MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX 0x040 + MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x040 + MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x040 >; }; - pinctrl_usdhc2_pwrseq: usdhc2pwrseqgrp { + pinctrl_uart3: uart3grp { fsl,pins = < - MX8MN_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x040 /* WL_REG_ON */ + MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX 0x040 + MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX 0x040 + MX8MN_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x040 + MX8MN_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x040 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX 0x040 + MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX 0x040 >; }; @@ -362,36 +403,9 @@ >; }; - pinctrl_wlan: wlangrp { - fsl,pins = < - MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x0d6 /* GPIO_0 - WIFI_GPIO_0 */ - MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x0d6 /* GPIO_1 - WIFI_GPIO_1 */ - MX8MN_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x0d6 /* BT_GPIO_5 - WIFI_GPIO_5 */ - MX8MN_IOMUXC_SPDIF_RX_GPIO5_IO4 0x0d6 /* I2S_CLK - WIFI_GPIO_6 */ - >; - }; - - pinctrl_uart2: uart2grp { - fsl,pins = < - MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x040 - MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x040 - >; - }; - - pinctrl_uart3: uart3grp { - fsl,pins = < - MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX 0x040 - MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX 0x040 - MX8MN_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x040 - MX8MN_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x040 - >; - }; - - pinctrl_bluetooth: bluetoothgrp { + pinctrl_usdhc2_pwrseq: usdhc2pwrseqgrp { fsl,pins = < - MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x044 /* BT_REG_ON */ - MX8MN_IOMUXC_ENET_TD3_GPIO1_IO18 0x046 /* BT_DEV_WAKE */ - MX8MN_IOMUXC_ENET_RD2_GPIO1_IO28 0x090 /* BT_HOST_WAKE */ + MX8MN_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x040 /* WL_REG_ON */ >; }; @@ -401,23 +415,12 @@ >; }; - pinctrl_fec1: fec1grp { + pinctrl_wlan: wlangrp { fsl,pins = < - MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x002 - MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x002 - MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x090 - MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x090 - MX8MN_IOMUXC_ENET_RXC_ENET1_RX_ER 0x090 - MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x016 - MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x016 - MX8MN_IOMUXC_ENET_TD2_ENET1_TX_CLK 0x016 - MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x016 - MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x090 - MX8MN_IOMUXC_ENET_TXC_ENET1_TX_ER 0x016 - MX8MN_IOMUXC_SD2_CD_B_GPIO2_IO12 0x150 /* RMII_INT - ENET_INT */ - MX8MN_IOMUXC_SD2_WP_GPIO2_IO20 0x150 /* RMII_EN - ENET_EN */ - MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x016 /* RMII_WAKE - GPIO_ENET_WAKE */ - MX8MN_IOMUXC_ENET_RD3_GPIO1_IO29 0x016 /* RMII_RESET - GPIO_ENET_RST */ + MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x0d6 /* GPIO_0 - WIFI_GPIO_0 */ + MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x0d6 /* GPIO_1 - WIFI_GPIO_1 */ + MX8MN_IOMUXC_GPIO1_IO04_GPIO1_IO4 0x0d6 /* BT_GPIO_5 - WIFI_GPIO_5 */ + MX8MN_IOMUXC_SPDIF_RX_GPIO5_IO4 0x0d6 /* I2S_CLK - WIFI_GPIO_6 */ >; }; }; diff --git a/arch/arm/dts/imx8mn-bsh-smm-s2pro.dts b/arch/arm/dts/imx8mn-bsh-smm-s2pro.dts index c6a8ed6745..fbbb336703 100644 --- a/arch/arm/dts/imx8mn-bsh-smm-s2pro.dts +++ b/arch/arm/dts/imx8mn-bsh-smm-s2pro.dts @@ -7,6 +7,7 @@ /dts-v1/; #include "imx8mn-bsh-smm-s2-common.dtsi" +#include / { model = "BSH SMM S2 PRO"; @@ -16,6 +17,65 @@ device_type = "memory"; reg = <0x0 0x40000000 0x0 0x20000000>; }; + + sound-tlv320aic31xx { + compatible = "fsl,imx-audio-tlv320aic31xx"; + model = "tlv320aic31xx-hifi"; + audio-cpu = <&sai3>; + audio-codec = <&tlv320dac3101>; + audio-asrc = <&easrc>; + audio-routing = + "Ext Spk", "SPL", + "Ext Spk", "SPR"; + mclk-id = ; + }; + + vdd_input: vdd_input { + compatible = "regulator-fixed"; + regulator-name = "vdd_input"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; +}; + +&easrc { + fsl,asrc-rate = <48000>; + fsl,asrc-format = <10>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + tlv320dac3101: audio-codec@18 { + compatible = "ti,tlv320dac3101"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dac_rst>; + reg = <0x18>; + #sound-dai-cells = <0>; + HPVDD-supply = <&buck4_reg>; + SPRVDD-supply = <&vdd_input>; + SPLVDD-supply = <&vdd_input>; + AVDD-supply = <&buck4_reg>; + IOVDD-supply = <&buck4_reg>; + DVDD-supply = <&buck5_reg>; + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + ai31xx-micbias-vg = ; + clocks = <&clk IMX8MN_CLK_SAI3_ROOT>; + }; +}; + +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MN_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + fsl,sai-mclk-direction-output; + status = "okay"; }; /* eMMC */ @@ -30,6 +90,36 @@ }; &iomuxc { + pinctrl_dac_rst: dacrstgrp { + fsl,pins = < + MX8MN_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 /* DAC_RST */ + >; + }; + + pinctrl_espi2: espi2grp { + fsl,pins = < + MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x082 + MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x082 + MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x082 + MX8MN_IOMUXC_ECSPI2_SS0_ECSPI2_SS0 0x040 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400000c3 + MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400000c3 + >; + }; + + pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + >; + }; + pinctrl_usdhc1: usdhc1grp { fsl,pins = < MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x40000090 diff --git a/arch/arm/dts/imx8mn-ddr4-evk.dts b/arch/arm/dts/imx8mn-ddr4-evk.dts index 7dfee715a2..d8ce217c60 100644 --- a/arch/arm/dts/imx8mn-ddr4-evk.dts +++ b/arch/arm/dts/imx8mn-ddr4-evk.dts @@ -59,6 +59,10 @@ interrupts = <3 IRQ_TYPE_LEVEL_LOW>; rohm,reset-snvs-powered; + #clock-cells = <0>; + clocks = <&osc_32k 0>; + clock-output-names = "clk-32k-out"; + regulators { buck1_reg: BUCK1 { regulator-name = "buck1"; diff --git a/arch/arm/dts/imx8mn-evk-u-boot.dtsi b/arch/arm/dts/imx8mn-evk-u-boot.dtsi index 593cf06eb9..c0d26f1f50 100644 --- a/arch/arm/dts/imx8mn-evk-u-boot.dtsi +++ b/arch/arm/dts/imx8mn-evk-u-boot.dtsi @@ -9,11 +9,11 @@ u-boot,dm-spl; }; -&{/soc@0/bus@30800000/i2c@30a20000/pca9450@25} { +&{/soc@0/bus@30800000/i2c@30a20000/pmic@25} { u-boot,dm-spl; }; -&{/soc@0/bus@30800000/i2c@30a20000/pca9450@25/regulators} { +&{/soc@0/bus@30800000/i2c@30a20000/pmic@25/regulators} { u-boot,dm-spl; }; diff --git a/arch/arm/dts/imx8mn-evk.dts b/arch/arm/dts/imx8mn-evk.dts index cd11fb28f5..4eb467df5b 100644 --- a/arch/arm/dts/imx8mn-evk.dts +++ b/arch/arm/dts/imx8mn-evk.dts @@ -31,7 +31,7 @@ }; &i2c1 { - pmic: pca9450@25 { + pmic: pmic@25 { compatible = "nxp,pca9450b"; reg = <0x25>; pinctrl-names = "default"; @@ -41,18 +41,18 @@ regulators { buck1: BUCK1{ - regulator-name = "BUCK1"; - regulator-min-microvolt = <600000>; - regulator-max-microvolt = <2187500>; + regulator-name = "VDD_SOC"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <950000>; regulator-boot-on; regulator-always-on; regulator-ramp-delay = <3125>; }; buck2: BUCK2 { - regulator-name = "BUCK2"; - regulator-min-microvolt = <600000>; - regulator-max-microvolt = <2187500>; + regulator-name = "VDD_ARM_0V9"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1000000>; regulator-boot-on; regulator-always-on; regulator-ramp-delay = <3125>; @@ -61,63 +61,63 @@ }; buck4: BUCK4{ - regulator-name = "BUCK4"; - regulator-min-microvolt = <600000>; - regulator-max-microvolt = <3400000>; + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; buck5: BUCK5{ - regulator-name = "BUCK5"; - regulator-min-microvolt = <600000>; - regulator-max-microvolt = <3400000>; + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; regulator-boot-on; regulator-always-on; }; buck6: BUCK6 { - regulator-name = "BUCK6"; - regulator-min-microvolt = <600000>; - regulator-max-microvolt = <3400000>; + regulator-name = "NVCC_DRAM_1V1"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; regulator-boot-on; regulator-always-on; }; ldo1: LDO1 { - regulator-name = "LDO1"; - regulator-min-microvolt = <1600000>; - regulator-max-microvolt = <3300000>; + regulator-name = "NVCC_SNVS_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; regulator-boot-on; regulator-always-on; }; ldo2: LDO2 { - regulator-name = "LDO2"; + regulator-name = "VDD_SNVS_0V8"; regulator-min-microvolt = <800000>; - regulator-max-microvolt = <1150000>; + regulator-max-microvolt = <800000>; regulator-boot-on; regulator-always-on; }; ldo3: LDO3 { - regulator-name = "LDO3"; - regulator-min-microvolt = <800000>; - regulator-max-microvolt = <3300000>; + regulator-name = "VDDA_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; regulator-boot-on; regulator-always-on; }; ldo4: LDO4 { - regulator-name = "LDO4"; - regulator-min-microvolt = <800000>; - regulator-max-microvolt = <3300000>; + regulator-name = "VDD_PHY_1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; regulator-boot-on; regulator-always-on; }; ldo5: LDO5 { - regulator-name = "LDO5"; + regulator-name = "NVCC_SD2"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; diff --git a/arch/arm/dts/imx8mn-evk.dtsi b/arch/arm/dts/imx8mn-evk.dtsi index fd253f0042..d1f6cccfa0 100644 --- a/arch/arm/dts/imx8mn-evk.dtsi +++ b/arch/arm/dts/imx8mn-evk.dtsi @@ -46,6 +46,40 @@ pinctrl-0 = <&pinctrl_ir>; linux,autosuspend-period = <125>; }; + + wm8524: audio-codec { + #sound-dai-cells = <0>; + compatible = "wlf,wm8524"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_wlf>; + wlf,mute-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>; + clocks = <&clk IMX8MN_CLK_SAI3_ROOT>; + clock-names = "mclk"; + }; + + sound-wm8524 { + compatible = "fsl,imx-audio-wm8524"; + model = "wm8524-audio"; + audio-cpu = <&sai3>; + audio-codec = <&wm8524>; + audio-asrc = <&easrc>; + audio-routing = + "Line Out Jack", "LINEVOUTL", + "Line Out Jack", "LINEVOUTR"; + }; + + sound-spdif { + compatible = "fsl,imx-audio-spdif"; + model = "imx-spdif"; + spdif-controller = <&spdif1>; + spdif-out; + spdif-in; + }; +}; + +&easrc { + fsl,asrc-rate = <48000>; + status = "okay"; }; &fec1 { @@ -76,6 +110,22 @@ }; }; +&flexspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexspi>; + status = "okay"; + + flash0: flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <166000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + }; +}; + &i2c1 { clock-frequency = <400000>; pinctrl-names = "default"; @@ -133,22 +183,51 @@ }; }; +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MN_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + fsl,sai-mclk-direction-output; + status = "okay"; +}; + &snvs_pwrkey { status = "okay"; }; +&spdif1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spdif1>; + assigned-clocks = <&clk IMX8MN_CLK_SPDIF1>; + assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + &uart2 { /* console */ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart2>; status = "okay"; }; +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + assigned-clocks = <&clk IMX8MN_CLK_UART3>; + assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>; + uart-has-rtscts; + status = "okay"; +}; + &usbotg1 { dr_mode = "otg"; hnp-disable; srp-disable; adp-disable; usb-role-switch; + disable-over-current; samsung,picophy-pre-emp-curr-control = <3>; samsung,picophy-dc-vol-level-adjust = <7>; status = "okay"; @@ -213,12 +292,29 @@ >; }; + pinctrl_flexspi: flexspigrp { + fsl,pins = < + MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2 + MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 + MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 + MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 + MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 + MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 + >; + }; + pinctrl_gpio_led: gpioledgrp { fsl,pins = < MX8MN_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 >; }; + pinctrl_gpio_wlf: gpiowlfgrp { + fsl,pins = < + MX8MN_IOMUXC_I2C4_SDA_GPIO5_IO21 0xd6 + >; + }; + pinctrl_ir: irgrp { fsl,pins = < MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x4f @@ -258,6 +354,22 @@ >; }; + pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6 + MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + >; + }; + + pinctrl_spdif1: spdif1grp { + fsl,pins = < + MX8MN_IOMUXC_SPDIF_TX_SPDIF1_OUT 0xd6 + MX8MN_IOMUXC_SPDIF_RX_SPDIF1_IN 0xd6 + >; + }; + pinctrl_typec1: typec1grp { fsl,pins = < MX8MN_IOMUXC_SD1_STROBE_GPIO2_IO11 0x159 @@ -271,6 +383,15 @@ >; }; + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MN_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x140 + MX8MN_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x140 + MX8MN_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x140 + MX8MN_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x140 + >; + }; + pinctrl_usdhc2_gpio: usdhc2gpiogrp { fsl,pins = < MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x1c4 diff --git a/arch/arm/dts/imx8mn-var-som.dtsi b/arch/arm/dts/imx8mn-var-som.dtsi index f97209fbd8..87b5e23c76 100644 --- a/arch/arm/dts/imx8mn-var-som.dtsi +++ b/arch/arm/dts/imx8mn-var-som.dtsi @@ -70,12 +70,12 @@ pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; ti,x-min = /bits/ 16 <125>; - touchscreen-size-x = /bits/ 16 <4008>; + touchscreen-size-x = <4008>; ti,y-min = /bits/ 16 <282>; - touchscreen-size-y = /bits/ 16 <3864>; + touchscreen-size-y = <3864>; ti,x-plate-ohms = /bits/ 16 <180>; - touchscreen-max-pressure = /bits/ 16 <255>; - touchscreen-average-samples = /bits/ 16 <10>; + touchscreen-max-pressure = <255>; + touchscreen-average-samples = <10>; ti,debounce-tol = /bits/ 16 <3>; ti,debounce-rep = /bits/ 16 <1>; ti,settle-delay-usec = /bits/ 16 <150>; @@ -91,8 +91,6 @@ phy-mode = "rgmii"; phy-handle = <ðphy>; phy-supply = <®_eth_phy>; - phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; - phy-reset-duration = <10>; fsl,magic-packet; status = "okay"; @@ -103,6 +101,8 @@ ethphy: ethernet-phy@4 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <4>; + reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; }; }; }; @@ -260,7 +260,8 @@ }; &usbotg1 { - dr_mode = "peripheral"; + dr_mode = "otg"; + usb-role-switch; status = "okay"; }; diff --git a/arch/arm/dts/imx8mn-venice-gw7902.dts b/arch/arm/dts/imx8mn-venice-gw7902.dts index d026d96558..367a232675 100644 --- a/arch/arm/dts/imx8mn-venice-gw7902.dts +++ b/arch/arm/dts/imx8mn-venice-gw7902.dts @@ -1,6 +1,6 @@ // SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* - * Copyright 2022 Gateworks Corporation + * Copyright 2021 Gateworks Corporation */ /dts-v1/; @@ -140,12 +140,13 @@ regulator-name = "3P3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; + regulator-always-on; }; reg_usb1_vbus: regulator-usb1 { + compatible = "regulator-fixed"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_reg_usb1>; - compatible = "regulator-fixed"; regulator-name = "usb_usb1_vbus"; gpio = <&gpio2 7 GPIO_ACTIVE_HIGH>; enable-active-high; @@ -154,9 +155,9 @@ }; reg_wifi: regulator-wifi { + compatible = "regulator-fixed"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_reg_wl>; - compatible = "regulator-fixed"; regulator-name = "wifi"; gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; enable-active-high; @@ -219,6 +220,10 @@ }; }; +&disp_blk_ctrl { + status = "disabled"; +}; + /* off-board header */ &ecspi2 { pinctrl-names = "default"; @@ -242,18 +247,55 @@ ethphy0: ethernet-phy@0 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <0>; - /* TI DP83867 props */ ti,rx-internal-delay = ; ti,tx-internal-delay = ; tx-fifo-depth = ; rx-fifo-depth = ; - /* GPY111 props */ - rx-internal-delay-ps = <2000>; - tx-internal-delay-ps = <2500>; }; }; }; +&gpio1 { + gpio-line-names = "", "", "", "", "", "", "", "", + "", "", "", "", "", "m2_reset", "", "m2_wdis#", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio2 { + gpio-line-names = "", "", "", "", "", "", "", "", + "uart2_en#", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio3 { + gpio-line-names = "", "m2_gdis#", "", "", "", "", "", "m2_off#", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio4 { + gpio-line-names = "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "app_gpio1", "", "uart1_rs485", + "", "uart1_term", "uart1_half", "app_gpio2", + "mipi_gpio1", "", "", ""; +}; + +&gpio5 { + gpio-line-names = "", "", "", "mipi_gpio4", + "mipi_gpio3", "mipi_gpio2", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpu { + status = "disabled"; +}; + &i2c1 { clock-frequency = <100000>; pinctrl-names = "default"; @@ -529,20 +571,15 @@ status = "okay"; accelerometer@19 { + compatible = "st,lis2de12"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_accel>; - compatible = "st,lis2de12"; reg = <0x19>; st,drdy-int-pin = <1>; interrupt-parent = <&gpio1>; interrupts = <12 IRQ_TYPE_LEVEL_LOW>; interrupt-names = "INT1"; }; - - secure-element@60 { - compatible = "nxp,se050"; - reg = <0x60>; - }; }; /* off-board header */ @@ -561,6 +598,10 @@ status = "okay"; }; +&pgc_gpumix { + status = "disabled"; +}; + /* off-board header */ &sai3 { pinctrl-names = "default"; @@ -591,6 +632,7 @@ pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_uart3_gpio>; rts-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; cts-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; + uart-has-rtscts; status = "okay"; bluetooth { @@ -648,7 +690,7 @@ pinctrl_hog: hoggrp { fsl,pins = < MX8MN_IOMUXC_NAND_CE0_B_GPIO3_IO1 0x40000159 /* M2_GDIS# */ - MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x40000041 /* M2_RST# */ + MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x40000041 /* M2_RESET */ MX8MN_IOMUXC_NAND_DATA01_GPIO3_IO7 0x40000119 /* M2_OFF# */ MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x40000159 /* M2_WDIS# */ MX8MN_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x40000041 /* APP GPIO1 */ @@ -726,11 +768,11 @@ pinctrl_gpio_leds: gpioledgrp { fsl,pins = < - MX8MN_IOMUXC_SAI5_RXD0_GPIO3_IO21 0x40000019 - MX8MN_IOMUXC_SAI5_RXD2_GPIO3_IO23 0x40000019 - MX8MN_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x40000019 - MX8MN_IOMUXC_SAI5_RXC_GPIO3_IO20 0x40000019 - MX8MN_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x40000019 + MX8MN_IOMUXC_SAI5_RXD0_GPIO3_IO21 0x19 + MX8MN_IOMUXC_SAI5_RXD2_GPIO3_IO23 0x19 + MX8MN_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x19 + MX8MN_IOMUXC_SAI5_RXC_GPIO3_IO20 0x19 + MX8MN_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x19 >; }; diff --git a/arch/arm/dts/imx8mn.dtsi b/arch/arm/dts/imx8mn.dtsi index edcb415b53..e41e1d56f9 100644 --- a/arch/arm/dts/imx8mn.dtsi +++ b/arch/arm/dts/imx8mn.dtsi @@ -65,6 +65,12 @@ clock-latency = <61036>; clocks = <&clk IMX8MN_CLK_ARM>; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; operating-points-v2 = <&a53_opp_table>; nvmem-cells = <&cpu_speed_grade>; @@ -80,6 +86,12 @@ clock-latency = <61036>; clocks = <&clk IMX8MN_CLK_ARM>; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; operating-points-v2 = <&a53_opp_table>; cpu-idle-states = <&cpu_pd_wait>; @@ -93,6 +105,12 @@ clock-latency = <61036>; clocks = <&clk IMX8MN_CLK_ARM>; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; operating-points-v2 = <&a53_opp_table>; cpu-idle-states = <&cpu_pd_wait>; @@ -106,6 +124,12 @@ clock-latency = <61036>; clocks = <&clk IMX8MN_CLK_ARM>; enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; next-level-cache = <&A53_L2>; operating-points-v2 = <&a53_opp_table>; cpu-idle-states = <&cpu_pd_wait>; @@ -114,6 +138,10 @@ A53_L2: l2-cache0 { compatible = "cache"; + cache-level = <2>; + cache-size = <0x80000>; + cache-line-size = <64>; + cache-sets = <512>; }; }; @@ -192,7 +220,6 @@ compatible = "arm,cortex-a53-pmu"; interrupts = ; - interrupt-affinity = <&A53_0>, <&A53_1>, <&A53_2>, <&A53_3>; }; psci { @@ -247,6 +274,7 @@ #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x0 0x0 0x3e000000>; + dma-ranges = <0x40000000 0x0 0x40000000 0xc0000000>; nvmem-cells = <&imx8mn_uid>; nvmem-cell-names = "soc_unique_id"; @@ -257,7 +285,7 @@ #size-cells = <1>; ranges; - spba: spba-bus@30000000 { + spba2: spba-bus@30000000 { compatible = "fsl,spba-bus", "simple-bus"; #address-cells = <1>; #size-cells = <1>; @@ -265,7 +293,7 @@ ranges; sai2: sai@30020000 { - compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai"; + compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai"; reg = <0x30020000 0x10000>; interrupts = ; clocks = <&clk IMX8MN_CLK_SAI2_IPG>, @@ -279,7 +307,7 @@ }; sai3: sai@30030000 { - compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai"; + compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai"; reg = <0x30030000 0x10000>; interrupts = ; clocks = <&clk IMX8MN_CLK_SAI3_IPG>, @@ -293,7 +321,7 @@ }; sai5: sai@30050000 { - compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai"; + compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai"; reg = <0x30050000 0x10000>; interrupts = ; clocks = <&clk IMX8MN_CLK_SAI5_IPG>, @@ -309,7 +337,7 @@ }; sai6: sai@30060000 { - compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai"; + compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai"; reg = <0x30060000 0x10000>; interrupts = ; clocks = <&clk IMX8MN_CLK_SAI6_IPG>, @@ -366,7 +394,7 @@ }; sai7: sai@300b0000 { - compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai"; + compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai"; reg = <0x300b0000 0x10000>; interrupts = ; clocks = <&clk IMX8MN_CLK_SAI7_IPG>, @@ -641,24 +669,23 @@ #power-domain-cells = <0>; reg = ; clocks = <&clk IMX8MN_CLK_GPU_CORE_ROOT>, - <&clk IMX8MN_CLK_GPU_SHADER_DIV>, + <&clk IMX8MN_CLK_GPU_SHADER>, <&clk IMX8MN_CLK_GPU_BUS_ROOT>, <&clk IMX8MN_CLK_GPU_AHB>; resets = <&src IMX8MQ_RESET_GPU_RESET>; }; - dispmix_pd: power-domain@3 { + pgc_dispmix: power-domain@3 { #power-domain-cells = <0>; reg = ; - clocks = <&clk IMX8MN_CLK_DISP_PIXEL_ROOT>, - <&clk IMX8MN_CLK_DISP_AXI_ROOT>, + clocks = <&clk IMX8MN_CLK_DISP_AXI_ROOT>, <&clk IMX8MN_CLK_DISP_APB_ROOT>; }; - mipi_pd: power-domain@4 { + pgc_mipi: power-domain@4 { #power-domain-cells = <0>; reg = ; - power-domains = <&dispmix_pd>; + power-domains = <&pgc_dispmix>; }; }; }; @@ -678,7 +705,7 @@ clocks = <&clk IMX8MN_CLK_PWM1_ROOT>, <&clk IMX8MN_CLK_PWM1_ROOT>; clock-names = "ipg", "per"; - #pwm-cells = <2>; + #pwm-cells = <3>; status = "disabled"; }; @@ -689,7 +716,7 @@ clocks = <&clk IMX8MN_CLK_PWM2_ROOT>, <&clk IMX8MN_CLK_PWM2_ROOT>; clock-names = "ipg", "per"; - #pwm-cells = <2>; + #pwm-cells = <3>; status = "disabled"; }; @@ -700,7 +727,7 @@ clocks = <&clk IMX8MN_CLK_PWM3_ROOT>, <&clk IMX8MN_CLK_PWM3_ROOT>; clock-names = "ipg", "per"; - #pwm-cells = <2>; + #pwm-cells = <3>; status = "disabled"; }; @@ -711,7 +738,7 @@ clocks = <&clk IMX8MN_CLK_PWM4_ROOT>, <&clk IMX8MN_CLK_PWM4_ROOT>; clock-names = "ipg", "per"; - #pwm-cells = <2>; + #pwm-cells = <3>; status = "disabled"; }; @@ -731,80 +758,88 @@ #size-cells = <1>; ranges; - ecspi1: spi@30820000 { - compatible = "fsl,imx8mn-ecspi", "fsl,imx51-ecspi"; + spba1: spba-bus@30800000 { + compatible = "fsl,spba-bus", "simple-bus"; #address-cells = <1>; - #size-cells = <0>; - reg = <0x30820000 0x10000>; - interrupts = ; - clocks = <&clk IMX8MN_CLK_ECSPI1_ROOT>, - <&clk IMX8MN_CLK_ECSPI1_ROOT>; - clock-names = "ipg", "per"; - dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + #size-cells = <1>; + reg = <0x30800000 0x100000>; + ranges; - ecspi2: spi@30830000 { - compatible = "fsl,imx8mn-ecspi", "fsl,imx51-ecspi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x30830000 0x10000>; - interrupts = ; - clocks = <&clk IMX8MN_CLK_ECSPI2_ROOT>, - <&clk IMX8MN_CLK_ECSPI2_ROOT>; - clock-names = "ipg", "per"; - dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + ecspi1: spi@30820000 { + compatible = "fsl,imx8mn-ecspi", "fsl,imx51-ecspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x30820000 0x10000>; + interrupts = ; + clocks = <&clk IMX8MN_CLK_ECSPI1_ROOT>, + <&clk IMX8MN_CLK_ECSPI1_ROOT>; + clock-names = "ipg", "per"; + dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>; + dma-names = "rx", "tx"; + status = "disabled"; + }; - ecspi3: spi@30840000 { - compatible = "fsl,imx8mn-ecspi", "fsl,imx51-ecspi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x30840000 0x10000>; - interrupts = ; - clocks = <&clk IMX8MN_CLK_ECSPI3_ROOT>, - <&clk IMX8MN_CLK_ECSPI3_ROOT>; - clock-names = "ipg", "per"; - dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + ecspi2: spi@30830000 { + compatible = "fsl,imx8mn-ecspi", "fsl,imx51-ecspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x30830000 0x10000>; + interrupts = ; + clocks = <&clk IMX8MN_CLK_ECSPI2_ROOT>, + <&clk IMX8MN_CLK_ECSPI2_ROOT>; + clock-names = "ipg", "per"; + dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>; + dma-names = "rx", "tx"; + status = "disabled"; + }; - uart1: serial@30860000 { - compatible = "fsl,imx8mn-uart", "fsl,imx6q-uart"; - reg = <0x30860000 0x10000>; - interrupts = ; - clocks = <&clk IMX8MN_CLK_UART1_ROOT>, - <&clk IMX8MN_CLK_UART1_ROOT>; - clock-names = "ipg", "per"; - dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + ecspi3: spi@30840000 { + compatible = "fsl,imx8mn-ecspi", "fsl,imx51-ecspi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x30840000 0x10000>; + interrupts = ; + clocks = <&clk IMX8MN_CLK_ECSPI3_ROOT>, + <&clk IMX8MN_CLK_ECSPI3_ROOT>; + clock-names = "ipg", "per"; + dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>; + dma-names = "rx", "tx"; + status = "disabled"; + }; - uart3: serial@30880000 { - compatible = "fsl,imx8mn-uart", "fsl,imx6q-uart"; - reg = <0x30880000 0x10000>; - interrupts = ; - clocks = <&clk IMX8MN_CLK_UART3_ROOT>, - <&clk IMX8MN_CLK_UART3_ROOT>; - clock-names = "ipg", "per"; - dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + uart1: serial@30860000 { + compatible = "fsl,imx8mn-uart", "fsl,imx6q-uart"; + reg = <0x30860000 0x10000>; + interrupts = ; + clocks = <&clk IMX8MN_CLK_UART1_ROOT>, + <&clk IMX8MN_CLK_UART1_ROOT>; + clock-names = "ipg", "per"; + dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>; + dma-names = "rx", "tx"; + status = "disabled"; + }; - uart2: serial@30890000 { - compatible = "fsl,imx8mn-uart", "fsl,imx6q-uart"; - reg = <0x30890000 0x10000>; - interrupts = ; - clocks = <&clk IMX8MN_CLK_UART2_ROOT>, - <&clk IMX8MN_CLK_UART2_ROOT>; - clock-names = "ipg", "per"; - status = "disabled"; + uart3: serial@30880000 { + compatible = "fsl,imx8mn-uart", "fsl,imx6q-uart"; + reg = <0x30880000 0x10000>; + interrupts = ; + clocks = <&clk IMX8MN_CLK_UART3_ROOT>, + <&clk IMX8MN_CLK_UART3_ROOT>; + clock-names = "ipg", "per"; + dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart2: serial@30890000 { + compatible = "fsl,imx8mn-uart", "fsl,imx6q-uart"; + reg = <0x30890000 0x10000>; + interrupts = ; + clocks = <&clk IMX8MN_CLK_UART2_ROOT>, + <&clk IMX8MN_CLK_UART2_ROOT>; + clock-names = "ipg", "per"; + status = "disabled"; + }; }; crypto: crypto@30900000 { @@ -898,7 +933,7 @@ }; usdhc1: mmc@30b40000 { - compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc"; + compatible = "fsl,imx8mn-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc"; reg = <0x30b40000 0x10000>; interrupts = ; clocks = <&clk IMX8MN_CLK_IPG_ROOT>, @@ -912,7 +947,7 @@ }; usdhc2: mmc@30b50000 { - compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc"; + compatible = "fsl,imx8mn-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc"; reg = <0x30b50000 0x10000>; interrupts = ; clocks = <&clk IMX8MN_CLK_IPG_ROOT>, @@ -926,7 +961,7 @@ }; usdhc3: mmc@30b60000 { - compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc"; + compatible = "fsl,imx8mn-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc"; reg = <0x30b60000 0x10000>; interrupts = ; clocks = <&clk IMX8MN_CLK_IPG_ROOT>, @@ -948,7 +983,7 @@ interrupts = ; clocks = <&clk IMX8MN_CLK_QSPI_ROOT>, <&clk IMX8MN_CLK_QSPI_ROOT>; - clock-names = "fspi", "fspi_en"; + clock-names = "fspi_en", "fspi"; status = "disabled"; }; @@ -964,7 +999,7 @@ }; fec1: ethernet@30be0000 { - compatible = "fsl,imx8mn-fec", "fsl,imx6sx-fec"; + compatible = "fsl,imx8mn-fec", "fsl,imx8mq-fec", "fsl,imx6sx-fec"; reg = <0x30be0000 0x10000>; interrupts = , , @@ -990,7 +1025,6 @@ fsl,num-rx-queues = <3>; nvmem-cells = <&fec_mac_address>; nvmem-cell-names = "mac-address"; - nvmem_macaddr_swap; fsl,stop-mode = <&gpr 0x10 3>; status = "disabled"; }; @@ -1004,6 +1038,34 @@ #size-cells = <1>; ranges; + disp_blk_ctrl: blk-ctrl@32e28000 { + compatible = "fsl,imx8mn-disp-blk-ctrl", "syscon"; + reg = <0x32e28000 0x100>; + power-domains = <&pgc_dispmix>, <&pgc_dispmix>, + <&pgc_dispmix>, <&pgc_mipi>, + <&pgc_mipi>; + power-domain-names = "bus", "isi", + "lcdif", "mipi-dsi", + "mipi-csi"; + clocks = <&clk IMX8MN_CLK_DISP_AXI>, + <&clk IMX8MN_CLK_DISP_APB>, + <&clk IMX8MN_CLK_DISP_AXI_ROOT>, + <&clk IMX8MN_CLK_DISP_APB_ROOT>, + <&clk IMX8MN_CLK_DISP_AXI_ROOT>, + <&clk IMX8MN_CLK_DISP_APB_ROOT>, + <&clk IMX8MN_CLK_DISP_PIXEL_ROOT>, + <&clk IMX8MN_CLK_DSI_CORE>, + <&clk IMX8MN_CLK_DSI_PHY_REF>, + <&clk IMX8MN_CLK_CSI1_PHY_REF>, + <&clk IMX8MN_CLK_CAMERA_PIXEL_ROOT>; + clock-names = "disp_axi", "disp_apb", + "disp_axi_root", "disp_apb_root", + "lcdif-axi", "lcdif-apb", "lcdif-pix", + "dsi-pclk", "dsi-ref", + "csi-aclk", "csi-pclk"; + #power-domain-cells = <1>; + }; + usbotg1: usb@32e40000 { compatible = "fsl,imx8mn-usb", "fsl,imx7d-usb"; reg = <0x32e40000 0x200>; @@ -1054,6 +1116,32 @@ status = "disabled"; }; + gpu: gpu@38000000 { + compatible = "vivante,gc"; + reg = <0x38000000 0x8000>; + interrupts = ; + clocks = <&clk IMX8MN_CLK_GPU_AHB>, + <&clk IMX8MN_CLK_GPU_BUS_ROOT>, + <&clk IMX8MN_CLK_GPU_CORE_ROOT>, + <&clk IMX8MN_CLK_GPU_SHADER>; + clock-names = "reg", "bus", "core", "shader"; + assigned-clocks = <&clk IMX8MN_CLK_GPU_CORE>, + <&clk IMX8MN_CLK_GPU_SHADER>, + <&clk IMX8MN_CLK_GPU_AXI>, + <&clk IMX8MN_CLK_GPU_AHB>, + <&clk IMX8MN_GPU_PLL>; + assigned-clock-parents = <&clk IMX8MN_GPU_PLL_OUT>, + <&clk IMX8MN_GPU_PLL_OUT>, + <&clk IMX8MN_SYS_PLL1_800M>, + <&clk IMX8MN_SYS_PLL1_800M>; + assigned-clock-rates = <400000000>, + <400000000>, + <800000000>, + <400000000>, + <1200000000>; + power-domains = <&pgc_gpumix>; + }; + gic: interrupt-controller@38800000 { compatible = "arm,gic-v3"; reg = <0x38800000 0x10000>, diff --git a/board/freescale/imx8mn_evk/spl.c b/board/freescale/imx8mn_evk/spl.c index 14cb51368f..c0bfb67199 100644 --- a/board/freescale/imx8mn_evk/spl.c +++ b/board/freescale/imx8mn_evk/spl.c @@ -69,7 +69,7 @@ int power_init_board(void) struct udevice *dev; int ret; - ret = pmic_get("pca9450@25", &dev); + ret = pmic_get("pmic@25", &dev); if (ret == -ENODEV) { puts("No pca9450@25\n"); return 0; diff --git a/include/dt-bindings/clock/imx8mn-clock.h b/include/dt-bindings/clock/imx8mn-clock.h index 621ea0e87c..07b8a282c2 100644 --- a/include/dt-bindings/clock/imx8mn-clock.h +++ b/include/dt-bindings/clock/imx8mn-clock.h @@ -234,6 +234,29 @@ #define IMX8MN_CLK_A53_CORE 214 -#define IMX8MN_CLK_END 215 +#define IMX8MN_CLK_CLKOUT1_SEL 215 +#define IMX8MN_CLK_CLKOUT1_DIV 216 +#define IMX8MN_CLK_CLKOUT1 217 +#define IMX8MN_CLK_CLKOUT2_SEL 218 +#define IMX8MN_CLK_CLKOUT2_DIV 219 +#define IMX8MN_CLK_CLKOUT2 220 + +#define IMX8MN_CLK_M7_CORE 221 + +#define IMX8MN_CLK_GPT_3M 222 +#define IMX8MN_CLK_GPT1 223 +#define IMX8MN_CLK_GPT1_ROOT 224 +#define IMX8MN_CLK_GPT2 225 +#define IMX8MN_CLK_GPT2_ROOT 226 +#define IMX8MN_CLK_GPT3 227 +#define IMX8MN_CLK_GPT3_ROOT 228 +#define IMX8MN_CLK_GPT4 229 +#define IMX8MN_CLK_GPT4_ROOT 230 +#define IMX8MN_CLK_GPT5 231 +#define IMX8MN_CLK_GPT5_ROOT 232 +#define IMX8MN_CLK_GPT6 233 +#define IMX8MN_CLK_GPT6_ROOT 234 + +#define IMX8MN_CLK_END 235 #endif diff --git a/include/dt-bindings/power/imx8mn-power.h b/include/dt-bindings/power/imx8mn-power.h index 102ee85a9b..eedd0e5819 100644 --- a/include/dt-bindings/power/imx8mn-power.h +++ b/include/dt-bindings/power/imx8mn-power.h @@ -12,4 +12,9 @@ #define IMX8MN_POWER_DOMAIN_DISPMIX 3 #define IMX8MN_POWER_DOMAIN_MIPI 4 +#define IMX8MN_DISPBLK_PD_MIPI_DSI 0 +#define IMX8MN_DISPBLK_PD_MIPI_CSI 1 +#define IMX8MN_DISPBLK_PD_LCDIF 2 +#define IMX8MN_DISPBLK_PD_ISI 3 + #endif diff --git a/include/dt-bindings/sound/tlv320aic31xx.h b/include/dt-bindings/sound/tlv320aic31xx.h new file mode 100644 index 0000000000..4a80238ab2 --- /dev/null +++ b/include/dt-bindings/sound/tlv320aic31xx.h @@ -0,0 +1,14 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __DT_TLV320AIC31XX_H +#define __DT_TLV320AIC31XX_H + +#define MICBIAS_2_0V 1 +#define MICBIAS_2_5V 2 +#define MICBIAS_AVDDV 3 + +#define PLL_CLKIN_MCLK 0x00 +#define PLL_CLKIN_BCLK 0x01 +#define PLL_CLKIN_GPIO1 0x02 +#define PLL_CLKIN_DIN 0x03 + +#endif /* __DT_TLV320AIC31XX_H */