From: Chin-Ting Kuo Date: Fri, 19 Aug 2022 09:01:04 +0000 (+0800) Subject: spi: aspeed: Add ASPEED SPI controller driver X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=4daa6bb6f76d3124e73cef22c98e7269140f42b0;p=u-boot.git spi: aspeed: Add ASPEED SPI controller driver Add ASPEED BMC FMC/SPI memory controller driver with spi-mem interface for AST2500 and AST2600 platform. There are three SPI memory controllers embedded in an ASPEED SoC. - FMC: Named as Firmware Memory Controller. After AC on, MCU ROM fetches initial device boot image from FMC chip select(CS) 0. - SPI1: Play the role of a SPI Master controller. Or, there is a dedicated path for HOST(X86) to access its BIOS flash mounted under BMC. spi-aspeed-smc.c implements the control sequence when SPI1 is a SPI master. - SPI2: It is a pure SPI flash controller. For most scenarios, flashes mounted under it are for pure storage purpose. ASPEED SPI controller supports 1-1-1, 1-1-2 and 1-1-4 SPI flash mode. Three types of command mode are supported, normal mode, command read/write mode and user mode. - Normal mode: Default mode. After power on, normal read command 03h or 13h is used to fetch boot image from SPI flash. - AST2500: Only 03h command can be used after power on or reset. - AST2600: If FMC04[6:4] is set, 13h command is used, otherwise, 03h command. The address length is decided by FMC04[2:0]. - Command mode: SPI controller can send command and address automatically when CPU read/write the related remapped or decoded address area. The command used by this mode can be configured by FMC10/14/18[23:16]. Also, the address length is decided by FMC04[2:0]. This mode will be implemented in the following patch series. - User mode: It is a traditional and pure SPI operation, where SPI transmission is controlled by CPU. It is the main mode in this patch. Each SPI controller in ASPEED SoC has its own decoded address mapping. Within each SPI controller decoded address, driver can assign a specific address region for each CS of a SPI controller. The decoded address cannot overlap to each other. With normal mode and command mode, the decoded address accessed by the CPU determines which CS is active. When user mode is adopted, the CS decoded address is a FIFO, CPU can send/receive any SPI transmission by accessing the related decoded address for the target CS. This patch only implements user mode initially. Command read/write mode will be implemented in the following patches. Signed-off-by: Chin-Ting Kuo --- diff --git a/MAINTAINERS b/MAINTAINERS index 36a2b69fcb..1ebcd368a6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -724,6 +724,13 @@ S: Maintained F: drivers/pci/pcie_phytium.c F: arch/arm/dts/phytium-durian.dts +ASPEED FMC SPI DRIVER +M: Chin-Ting Kuo +M: Cédric Le Goater +R: Aspeed BMC SW team +S: Maintained +F: drivers/spi/spi-aspeed-smc.c + BINMAN M: Simon Glass M: Alper Nebi Yasak diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 75b794548b..8ca9274ef4 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -401,6 +401,14 @@ config SANDBOX_SPI }; }; +config SPI_ASPEED_SMC + bool "ASPEED SPI flash controller driver" + depends on DM_SPI && SPI_MEM + default n + help + Enable ASPEED SPI flash controller driver for AST2500 + and AST2600 SoCs. + config SPI_SIFIVE bool "SiFive SPI driver" help diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 4de77c260a..7ba953d2df 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_CADENCE_QSPI) += cadence_qspi.o cadence_qspi_apb.o obj-$(CONFIG_CADENCE_OSPI_VERSAL) += cadence_ospi_versal.o obj-$(CONFIG_SANDBOX) += spi-emul-uclass.o obj-$(CONFIG_SOFT_SPI) += soft_spi.o +obj-$(CONFIG_SPI_ASPEED_SMC) += spi-aspeed-smc.o obj-$(CONFIG_SPI_MEM) += spi-mem.o obj-$(CONFIG_TI_QSPI) += ti_qspi.o obj-$(CONFIG_FSL_QSPI) += fsl_qspi.o diff --git a/drivers/spi/spi-aspeed-smc.c b/drivers/spi/spi-aspeed-smc.c new file mode 100644 index 0000000000..25b490bcf4 --- /dev/null +++ b/drivers/spi/spi-aspeed-smc.c @@ -0,0 +1,603 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * ASPEED FMC/SPI Controller driver + * + * Copyright (c) 2022 ASPEED Corporation. + * Copyright (c) 2022 IBM Corporation. + * + * Author: + * Chin-Ting Kuo + * Cedric Le Goater + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define ASPEED_SPI_MAX_CS 3 + +#define CTRL_IO_SINGLE_DATA 0 +#define CTRL_IO_QUAD_DATA BIT(30) +#define CTRL_IO_DUAL_DATA BIT(29) + +#define CTRL_IO_MODE_USER GENMASK(1, 0) +#define CTRL_IO_MODE_CMD_READ BIT(0) +#define CTRL_IO_MODE_CMD_WRITE BIT(1) +#define CTRL_STOP_ACTIVE BIT(2) + +struct aspeed_spi_regs { + u32 conf; /* 0x00 CE Type Setting */ + u32 ctrl; /* 0x04 CE Control */ + u32 intr_ctrl; /* 0x08 Interrupt Control and Status */ + u32 cmd_ctrl; /* 0x0c Command Control */ + u32 ce_ctrl[ASPEED_SPI_MAX_CS]; /* 0x10 .. 0x18 CEx Control */ + u32 _reserved0[5]; /* .. */ + u32 segment_addr[ASPEED_SPI_MAX_CS]; /* 0x30 .. 0x38 Segment Address */ + u32 _reserved1[5]; /* .. */ + u32 soft_rst_cmd_ctrl; /* 0x50 Auto Soft-Reset Command Control */ + u32 _reserved2[11]; /* .. */ + u32 dma_ctrl; /* 0x80 DMA Control/Status */ + u32 dma_flash_addr; /* 0x84 DMA Flash Side Address */ + u32 dma_dram_addr; /* 0x88 DMA DRAM Side Address */ + u32 dma_len; /* 0x8c DMA Length Register */ + u32 dma_checksum; /* 0x90 Checksum Calculation Result */ + u32 timings[ASPEED_SPI_MAX_CS]; /* 0x94 Read Timing Compensation */ +}; + +struct aspeed_spi_plat { + u8 max_cs; + void __iomem *ahb_base; /* AHB address base for all flash devices. */ + fdt_size_t ahb_sz; /* Overall AHB window size for all flash device. */ +}; + +struct aspeed_spi_flash { + void __iomem *ahb_base; + u32 ahb_decoded_sz; + u32 ce_ctrl_user; + u32 ce_ctrl_read; +}; + +struct aspeed_spi_priv { + u32 num_cs; + struct aspeed_spi_regs *regs; + struct aspeed_spi_info *info; + struct aspeed_spi_flash flashes[ASPEED_SPI_MAX_CS]; +}; + +struct aspeed_spi_info { + u32 io_mode_mask; + u32 max_bus_width; + u32 min_decoded_sz; + void (*set_4byte)(struct udevice *bus, u32 cs); + u32 (*segment_start)(struct udevice *bus, u32 reg); + u32 (*segment_end)(struct udevice *bus, u32 reg); + u32 (*segment_reg)(u32 start, u32 end); +}; + +static u32 aspeed_spi_get_io_mode(u32 bus_width) +{ + switch (bus_width) { + case 1: + return CTRL_IO_SINGLE_DATA; + case 2: + return CTRL_IO_DUAL_DATA; + case 4: + return CTRL_IO_QUAD_DATA; + default: + /* keep in default value */ + return CTRL_IO_SINGLE_DATA; + } +} + +static u32 ast2500_spi_segment_start(struct udevice *bus, u32 reg) +{ + struct aspeed_spi_plat *plat = dev_get_plat(bus); + u32 start_offset = ((reg >> 16) & 0xff) << 23; + + if (start_offset == 0) + return (u32)plat->ahb_base; + + return (u32)plat->ahb_base + start_offset; +} + +static u32 ast2500_spi_segment_end(struct udevice *bus, u32 reg) +{ + struct aspeed_spi_plat *plat = dev_get_plat(bus); + u32 end_offset = ((reg >> 24) & 0xff) << 23; + + /* Meaningless end_offset, set to physical ahb base. */ + if (end_offset == 0) + return (u32)plat->ahb_base; + + return (u32)plat->ahb_base + end_offset; +} + +static u32 ast2500_spi_segment_reg(u32 start, u32 end) +{ + if (start == end) + return 0; + + return ((((start) >> 23) & 0xff) << 16) | ((((end) >> 23) & 0xff) << 24); +} + +static void ast2500_spi_chip_set_4byte(struct udevice *bus, u32 cs) +{ + struct aspeed_spi_priv *priv = dev_get_priv(bus); + u32 reg_val; + + reg_val = readl(&priv->regs->ctrl); + reg_val |= 0x1 << cs; + writel(reg_val, &priv->regs->ctrl); +} + +static u32 ast2600_spi_segment_start(struct udevice *bus, u32 reg) +{ + struct aspeed_spi_plat *plat = dev_get_plat(bus); + u32 start_offset = (reg << 16) & 0x0ff00000; + + if (start_offset == 0) + return (u32)plat->ahb_base; + + return (u32)plat->ahb_base + start_offset; +} + +static u32 ast2600_spi_segment_end(struct udevice *bus, u32 reg) +{ + struct aspeed_spi_plat *plat = dev_get_plat(bus); + u32 end_offset = reg & 0x0ff00000; + + /* Meaningless end_offset, set to physical ahb base. */ + if (end_offset == 0) + return (u32)plat->ahb_base; + + return (u32)plat->ahb_base + end_offset + 0x100000; +} + +static u32 ast2600_spi_segment_reg(u32 start, u32 end) +{ + if (start == end) + return 0; + + return ((start & 0x0ff00000) >> 16) | ((end - 0x100000) & 0x0ff00000); +} + +static void ast2600_spi_chip_set_4byte(struct udevice *bus, u32 cs) +{ + struct aspeed_spi_priv *priv = dev_get_priv(bus); + u32 reg_val; + + reg_val = readl(&priv->regs->ctrl); + reg_val |= 0x11 << cs; + writel(reg_val, &priv->regs->ctrl); +} + +static int aspeed_spi_read_from_ahb(void __iomem *ahb_base, void *buf, + size_t len) +{ + size_t offset = 0; + + if (IS_ALIGNED((uintptr_t)ahb_base, sizeof(uintptr_t)) && + IS_ALIGNED((uintptr_t)buf, sizeof(uintptr_t))) { + readsl(ahb_base, buf, len >> 2); + offset = len & ~0x3; + len -= offset; + } + + readsb(ahb_base, (u8 *)buf + offset, len); + + return 0; +} + +static int aspeed_spi_write_to_ahb(void __iomem *ahb_base, const void *buf, + size_t len) +{ + size_t offset = 0; + + if (IS_ALIGNED((uintptr_t)ahb_base, sizeof(uintptr_t)) && + IS_ALIGNED((uintptr_t)buf, sizeof(uintptr_t))) { + writesl(ahb_base, buf, len >> 2); + offset = len & ~0x3; + len -= offset; + } + + writesb(ahb_base, (u8 *)buf + offset, len); + + return 0; +} + +/* + * Currently, only support 1-1-1, 1-1-2 or 1-1-4 + * SPI NOR flash operation format. + */ +static bool aspeed_spi_supports_op(struct spi_slave *slave, + const struct spi_mem_op *op) +{ + struct udevice *bus = slave->dev->parent; + struct aspeed_spi_priv *priv = dev_get_priv(bus); + + if (op->cmd.buswidth > 1) + return false; + + if (op->addr.nbytes != 0) { + if (op->addr.buswidth > 1) + return false; + if (op->addr.nbytes < 3 || op->addr.nbytes > 4) + return false; + } + + if (op->dummy.nbytes != 0) { + if (op->dummy.buswidth > 1 || op->dummy.nbytes > 7) + return false; + } + + if (op->data.nbytes != 0 && + op->data.buswidth > priv->info->max_bus_width) + return false; + + if (!spi_mem_default_supports_op(slave, op)) + return false; + + return true; +} + +static int aspeed_spi_exec_op_user_mode(struct spi_slave *slave, + const struct spi_mem_op *op) +{ + struct udevice *dev = slave->dev; + struct udevice *bus = dev->parent; + struct aspeed_spi_priv *priv = dev_get_priv(bus); + struct dm_spi_slave_plat *slave_plat = dev_get_parent_plat(slave->dev); + u32 cs = slave_plat->cs; + u32 ce_ctrl_reg = (u32)&priv->regs->ce_ctrl[cs]; + u32 ce_ctrl_val; + struct aspeed_spi_flash *flash = &priv->flashes[cs]; + u8 dummy_data[16] = {0}; + u8 addr[4] = {0}; + int i; + + dev_dbg(dev, "cmd:%x(%d),addr:%llx(%d),dummy:%d(%d),data_len:0x%x(%d)\n", + op->cmd.opcode, op->cmd.buswidth, op->addr.val, + op->addr.buswidth, op->dummy.nbytes, op->dummy.buswidth, + op->data.nbytes, op->data.buswidth); + + /* + * Set controller to 4-byte address mode + * if flash is in 4-byte address mode. + */ + if (op->cmd.opcode == SPINOR_OP_EN4B) + priv->info->set_4byte(bus, cs); + + /* Start user mode */ + ce_ctrl_val = flash->ce_ctrl_user; + writel(ce_ctrl_val, ce_ctrl_reg); + ce_ctrl_val &= (~CTRL_STOP_ACTIVE); + writel(ce_ctrl_val, ce_ctrl_reg); + + /* Send command */ + aspeed_spi_write_to_ahb(flash->ahb_base, &op->cmd.opcode, 1); + + /* Send address */ + for (i = op->addr.nbytes; i > 0; i--) { + addr[op->addr.nbytes - i] = + ((u32)op->addr.val >> ((i - 1) * 8)) & 0xff; + } + + /* Change io_mode */ + ce_ctrl_val &= ~priv->info->io_mode_mask; + ce_ctrl_val |= aspeed_spi_get_io_mode(op->addr.buswidth); + writel(ce_ctrl_val, ce_ctrl_reg); + aspeed_spi_write_to_ahb(flash->ahb_base, addr, op->addr.nbytes); + + /* Send dummy cycles */ + aspeed_spi_write_to_ahb(flash->ahb_base, dummy_data, op->dummy.nbytes); + + /* Change io_mode */ + ce_ctrl_val &= ~priv->info->io_mode_mask; + ce_ctrl_val |= aspeed_spi_get_io_mode(op->data.buswidth); + writel(ce_ctrl_val, ce_ctrl_reg); + + /* Send data */ + if (op->data.dir == SPI_MEM_DATA_OUT) { + aspeed_spi_write_to_ahb(flash->ahb_base, op->data.buf.out, + op->data.nbytes); + } else { + aspeed_spi_read_from_ahb(flash->ahb_base, op->data.buf.in, + op->data.nbytes); + } + + ce_ctrl_val |= CTRL_STOP_ACTIVE; + writel(ce_ctrl_val, ce_ctrl_reg); + + /* Restore controller setting. */ + writel(flash->ce_ctrl_read, ce_ctrl_reg); + + return 0; +} + +static struct aspeed_spi_flash *aspeed_spi_get_flash(struct udevice *dev) +{ + struct udevice *bus = dev->parent; + struct dm_spi_slave_plat *slave_plat = dev_get_parent_plat(dev); + struct aspeed_spi_plat *plat = dev_get_plat(bus); + struct aspeed_spi_priv *priv = dev_get_priv(bus); + u32 cs = slave_plat->cs; + + if (cs >= plat->max_cs) { + dev_err(dev, "invalid CS %u\n", cs); + return NULL; + } + + return &priv->flashes[cs]; +} + +static void aspeed_spi_decoded_base_calculate(struct udevice *bus) +{ + struct aspeed_spi_plat *plat = dev_get_plat(bus); + struct aspeed_spi_priv *priv = dev_get_priv(bus); + u32 cs; + + priv->flashes[0].ahb_base = plat->ahb_base; + + for (cs = 1; cs < plat->max_cs; cs++) { + priv->flashes[cs].ahb_base = + priv->flashes[cs - 1].ahb_base + + priv->flashes[cs - 1].ahb_decoded_sz; + } +} + +static void aspeed_spi_decoded_range_set(struct udevice *bus) +{ + struct aspeed_spi_plat *plat = dev_get_plat(bus); + struct aspeed_spi_priv *priv = dev_get_priv(bus); + u32 decoded_reg_val; + u32 start_addr, end_addr; + u32 cs; + + for (cs = 0; cs < plat->max_cs; cs++) { + start_addr = (u32)priv->flashes[cs].ahb_base; + end_addr = (u32)priv->flashes[cs].ahb_base + + priv->flashes[cs].ahb_decoded_sz; + + decoded_reg_val = priv->info->segment_reg(start_addr, end_addr); + + writel(decoded_reg_val, &priv->regs->segment_addr[cs]); + + dev_dbg(bus, "cs: %d, decoded_reg: 0x%x, start: 0x%x, end: 0x%x\n", + cs, decoded_reg_val, start_addr, end_addr); + } +} + +static int aspeed_spi_decoded_range_config(struct udevice *bus) +{ + aspeed_spi_decoded_base_calculate(bus); + aspeed_spi_decoded_range_set(bus); + + return 0; +} + +/* + * Initialize SPI controller for each chip select. + * Here, only the minimum decode range is configured + * in order to get device (SPI NOR flash) information + * at the early stage. + */ +static int aspeed_spi_ctrl_init(struct udevice *bus) +{ + int ret; + struct aspeed_spi_plat *plat = dev_get_plat(bus); + struct aspeed_spi_priv *priv = dev_get_priv(bus); + u32 cs; + u32 reg_val; + u32 decoded_sz; + + /* Enable write capability for all CS. */ + reg_val = readl(&priv->regs->conf); + writel(reg_val | (GENMASK(plat->max_cs - 1, 0) << 16), + &priv->regs->conf); + + memset(priv->flashes, 0x0, + sizeof(struct aspeed_spi_flash) * ASPEED_SPI_MAX_CS); + + /* Initial user mode. */ + for (cs = 0; cs < priv->num_cs; cs++) { + priv->flashes[cs].ce_ctrl_user = + (CTRL_STOP_ACTIVE | CTRL_IO_MODE_USER); + } + + /* Assign basic AHB decoded size for each CS. */ + for (cs = 0; cs < plat->max_cs; cs++) { + reg_val = readl(&priv->regs->segment_addr[cs]); + decoded_sz = priv->info->segment_end(bus, reg_val) - + priv->info->segment_start(bus, reg_val); + + if (decoded_sz < priv->info->min_decoded_sz) + decoded_sz = priv->info->min_decoded_sz; + + priv->flashes[cs].ahb_decoded_sz = decoded_sz; + } + + ret = aspeed_spi_decoded_range_config(bus); + + return ret; +} + +static const struct aspeed_spi_info ast2500_fmc_info = { + .io_mode_mask = 0x70000000, + .max_bus_width = 2, + .min_decoded_sz = 0x800000, + .set_4byte = ast2500_spi_chip_set_4byte, + .segment_start = ast2500_spi_segment_start, + .segment_end = ast2500_spi_segment_end, + .segment_reg = ast2500_spi_segment_reg, +}; + +/* + * There are some different between FMC and SPI controllers. + * For example, DMA operation, but this isn't implemented currently. + */ +static const struct aspeed_spi_info ast2500_spi_info = { + .io_mode_mask = 0x70000000, + .max_bus_width = 2, + .min_decoded_sz = 0x800000, + .set_4byte = ast2500_spi_chip_set_4byte, + .segment_start = ast2500_spi_segment_start, + .segment_end = ast2500_spi_segment_end, + .segment_reg = ast2500_spi_segment_reg, +}; + +static const struct aspeed_spi_info ast2600_fmc_info = { + .io_mode_mask = 0xf0000000, + .max_bus_width = 4, + .min_decoded_sz = 0x200000, + .set_4byte = ast2600_spi_chip_set_4byte, + .segment_start = ast2600_spi_segment_start, + .segment_end = ast2600_spi_segment_end, + .segment_reg = ast2600_spi_segment_reg, +}; + +static const struct aspeed_spi_info ast2600_spi_info = { + .io_mode_mask = 0xf0000000, + .max_bus_width = 4, + .min_decoded_sz = 0x200000, + .set_4byte = ast2600_spi_chip_set_4byte, + .segment_start = ast2600_spi_segment_start, + .segment_end = ast2600_spi_segment_end, + .segment_reg = ast2600_spi_segment_reg, +}; + +static int aspeed_spi_claim_bus(struct udevice *dev) +{ + struct udevice *bus = dev->parent; + struct dm_spi_slave_plat *slave_plat = dev_get_parent_plat(dev); + + dev_dbg(bus, "%s: claim bus CS%u\n", bus->name, slave_plat->cs); + + return 0; +} + +static int aspeed_spi_release_bus(struct udevice *dev) +{ + struct udevice *bus = dev->parent; + struct dm_spi_slave_plat *slave_plat = dev_get_parent_plat(dev); + + dev_dbg(bus, "%s: release bus CS%u\n", bus->name, slave_plat->cs); + + if (!aspeed_spi_get_flash(dev)) + return -ENODEV; + + return 0; +} + +static int aspeed_spi_set_mode(struct udevice *bus, uint mode) +{ + dev_dbg(bus, "%s: setting mode to %x\n", bus->name, mode); + + return 0; +} + +static int aspeed_spi_set_speed(struct udevice *bus, uint hz) +{ + dev_dbg(bus, "%s: setting speed to %u\n", bus->name, hz); + /* + * ASPEED SPI controller supports multiple CS with different + * clock frequency. We cannot distinguish which CS here. + * Thus, the related implementation is postponed to claim_bus. + */ + + return 0; +} + +static int apseed_spi_of_to_plat(struct udevice *bus) +{ + struct aspeed_spi_plat *plat = dev_get_plat(bus); + struct aspeed_spi_priv *priv = dev_get_priv(bus); + + priv->regs = (void __iomem *)devfdt_get_addr_index(bus, 0); + if ((u32)priv->regs == FDT_ADDR_T_NONE) { + dev_err(bus, "wrong ctrl base\n"); + return -ENODEV; + } + + plat->ahb_base = + (void __iomem *)devfdt_get_addr_size_index(bus, 1, &plat->ahb_sz); + if ((u32)plat->ahb_base == FDT_ADDR_T_NONE) { + dev_err(bus, "wrong AHB base\n"); + return -ENODEV; + } + + plat->max_cs = dev_read_u32_default(bus, "num-cs", ASPEED_SPI_MAX_CS); + if (plat->max_cs > ASPEED_SPI_MAX_CS) + return -EINVAL; + + dev_dbg(bus, "ctrl_base = 0x%x, ahb_base = 0x%p, size = 0x%lx\n", + (u32)priv->regs, plat->ahb_base, plat->ahb_sz); + dev_dbg(bus, "max_cs = %d\n", plat->max_cs); + + return 0; +} + +static int aspeed_spi_probe(struct udevice *bus) +{ + int ret; + struct aspeed_spi_priv *priv = dev_get_priv(bus); + struct udevice *dev; + + priv->info = (struct aspeed_spi_info *)dev_get_driver_data(bus); + + priv->num_cs = 0; + for (device_find_first_child(bus, &dev); dev; + device_find_next_child(&dev)) { + priv->num_cs++; + } + + if (priv->num_cs > ASPEED_SPI_MAX_CS) + return -EINVAL; + + ret = aspeed_spi_ctrl_init(bus); + + return ret; +} + +static const struct spi_controller_mem_ops aspeed_spi_mem_ops = { + .supports_op = aspeed_spi_supports_op, + .exec_op = aspeed_spi_exec_op_user_mode, +}; + +static const struct dm_spi_ops aspeed_spi_ops = { + .claim_bus = aspeed_spi_claim_bus, + .release_bus = aspeed_spi_release_bus, + .set_speed = aspeed_spi_set_speed, + .set_mode = aspeed_spi_set_mode, + .mem_ops = &aspeed_spi_mem_ops, +}; + +static const struct udevice_id aspeed_spi_ids[] = { + { .compatible = "aspeed,ast2500-fmc", .data = (ulong)&ast2500_fmc_info, }, + { .compatible = "aspeed,ast2500-spi", .data = (ulong)&ast2500_spi_info, }, + { .compatible = "aspeed,ast2600-fmc", .data = (ulong)&ast2600_fmc_info, }, + { .compatible = "aspeed,ast2600-spi", .data = (ulong)&ast2600_spi_info, }, + { } +}; + +U_BOOT_DRIVER(aspeed_spi) = { + .name = "aspeed_spi_smc", + .id = UCLASS_SPI, + .of_match = aspeed_spi_ids, + .ops = &aspeed_spi_ops, + .of_to_plat = apseed_spi_of_to_plat, + .plat_auto = sizeof(struct aspeed_spi_plat), + .priv_auto = sizeof(struct aspeed_spi_priv), + .probe = aspeed_spi_probe, +};