From: Piotr Wilczek Date: Fri, 20 Sep 2013 13:01:27 +0000 (+0200) Subject: samsung: trats2: add support for new board Trats2 X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=4d6c96711bd550ae292df566c2b36ff3e3dac24c;p=u-boot.git samsung: trats2: add support for new board Trats2 This patch add support for a new Samsung board Trats2. Signed-off-by: Piotr Wilczek Signed-off-by: Kyungmin Park Signed-off-by: Minkyu Kang --- diff --git a/board/samsung/trats2/Makefile b/board/samsung/trats2/Makefile new file mode 100644 index 0000000000..805fb8191a --- /dev/null +++ b/board/samsung/trats2/Makefile @@ -0,0 +1,34 @@ +# +# Copyright (c) 2000 - 2013 Samsung Electronics Co., Ltd. All rights reserved. +# Sanghee Kim +# +# SPDX-License-Identifier: GPL-2.0+ +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y := trats2.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) + + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c new file mode 100644 index 0000000000..d44d825e80 --- /dev/null +++ b/board/samsung/trats2/trats2.c @@ -0,0 +1,513 @@ +/* + * Copyright (c) 2013 Samsung Electronics Co., Ltd. All rights reserved. + * Sanghee Kim + * Piotr Wilczek + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +static struct exynos4x12_gpio_part1 *gpio1; +static struct exynos4x12_gpio_part2 *gpio2; + +static unsigned int board_rev = -1; + +static inline u32 get_model_rev(void); + +static void check_hw_revision(void) +{ + int modelrev = 0; + int i; + + gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE; + + /* + * GPM1[1:0]: MODEL_REV[1:0] + * Don't set as pull-none for these N/C pin. + * TRM say that it may cause unexcepted state and leakage current. + * and pull-none is only for output function. + */ + for (i = 0; i < 2; i++) + s5p_gpio_cfg_pin(&gpio2->m1, i, GPIO_INPUT); + + /* GPM1[5:2]: HW_REV[3:0] */ + for (i = 2; i < 6; i++) { + s5p_gpio_cfg_pin(&gpio2->m1, i, GPIO_INPUT); + s5p_gpio_set_pull(&gpio2->m1, i, GPIO_PULL_NONE); + } + + /* GPM1[1:0]: MODEL_REV[1:0] */ + for (i = 0; i < 2; i++) + modelrev |= (s5p_gpio_get_value(&gpio2->m1, i) << i); + + /* board_rev[15:8] = model */ + board_rev = modelrev << 8; +} + +#ifdef CONFIG_DISPLAY_BOARDINFO +int checkboard(void) +{ + puts("Board:\tTRATS2\n"); + return 0; +} +#endif + +static void show_hw_revision(void) +{ + printf("HW Revision:\t0x%04x\n", board_rev); +} + +u32 get_board_rev(void) +{ + return board_rev; +} + +static inline u32 get_model_rev(void) +{ + return (board_rev >> 8) & 0xff; +} + +static void board_external_gpio_init(void) +{ + gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE; + + /* + * some pins which in alive block are connected with external pull-up + * but it's default setting is pull-down. + * if that pin set as input then that floated + */ + + s5p_gpio_set_pull(&gpio2->x0, 2, GPIO_PULL_NONE); /* PS_ALS_INT */ + s5p_gpio_set_pull(&gpio2->x0, 4, GPIO_PULL_NONE); /* TSP_nINT */ + s5p_gpio_set_pull(&gpio2->x0, 7, GPIO_PULL_NONE); /* AP_PMIC_IRQ*/ + s5p_gpio_set_pull(&gpio2->x1, 5, GPIO_PULL_NONE); /* IF_PMIC_IRQ*/ + s5p_gpio_set_pull(&gpio2->x2, 0, GPIO_PULL_NONE); /* VOL_UP */ + s5p_gpio_set_pull(&gpio2->x2, 1, GPIO_PULL_NONE); /* VOL_DOWN */ + s5p_gpio_set_pull(&gpio2->x2, 3, GPIO_PULL_NONE); /* FUEL_ALERT */ + s5p_gpio_set_pull(&gpio2->x2, 4, GPIO_PULL_NONE); /* ADC_INT */ + s5p_gpio_set_pull(&gpio2->x2, 7, GPIO_PULL_NONE); /* nPOWER */ + s5p_gpio_set_pull(&gpio2->x3, 0, GPIO_PULL_NONE); /* WPC_INT */ + s5p_gpio_set_pull(&gpio2->x3, 5, GPIO_PULL_NONE); /* OK_KEY */ + s5p_gpio_set_pull(&gpio2->x3, 7, GPIO_PULL_NONE); /* HDMI_HPD */ +} + +#ifdef CONFIG_SYS_I2C_INIT_BOARD +static void board_init_i2c(void) +{ + gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE; + gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE; + + /* I2C_7 */ + s5p_gpio_direction_output(&gpio1->d0, 2, 1); + s5p_gpio_direction_output(&gpio1->d0, 3, 1); + + /* I2C_8 */ + s5p_gpio_direction_output(&gpio1->f1, 4, 1); + s5p_gpio_direction_output(&gpio1->f1, 5, 1); + + /* I2C_9 */ + s5p_gpio_direction_output(&gpio2->m2, 1, 1); + s5p_gpio_direction_output(&gpio2->m2, 0, 1); +} +#endif + +int board_early_init_f(void) +{ + check_hw_revision(); + board_external_gpio_init(); + + gd->flags |= GD_FLG_DISABLE_CONSOLE; + + return 0; +} + +static int pmic_init_max77686(void); + +int board_init(void) +{ + struct exynos4_power *pwr = + (struct exynos4_power *)EXYNOS4X12_POWER_BASE; + + gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; + + /* workaround: clear INFORM4..5 */ + writel(0, (unsigned int)&pwr->inform4); + writel(0, (unsigned int)&pwr->inform5); + + return 0; +} + +int power_init_board(void) +{ + int chrg; + struct power_battery *pb; + struct pmic *p_chrg, *p_muic, *p_fg, *p_bat; + +#ifdef CONFIG_SYS_I2C_INIT_BOARD + board_init_i2c(); +#endif + pmic_init(I2C_0); /* I2C adapter 0 - bus name I2C_5 */ + pmic_init_max77686(); + pmic_init_max77693(I2C_2); /* I2C adapter 2 - bus name I2C_10 */ + power_muic_init(I2C_2); /* I2C adapter 2 - bus name I2C_10 */ + power_fg_init(I2C_1); /* I2C adapter 1 - bus name I2C_9 */ + power_bat_init(0); + + p_chrg = pmic_get("MAX77693_PMIC"); + if (!p_chrg) { + puts("MAX77693_PMIC: Not found\n"); + return -ENODEV; + } + + p_muic = pmic_get("MAX77693_MUIC"); + if (!p_muic) { + puts("MAX77693_MUIC: Not found\n"); + return -ENODEV; + } + + p_fg = pmic_get("MAX77693_FG"); + if (!p_fg) { + puts("MAX17042_FG: Not found\n"); + return -ENODEV; + } + + if (p_chrg->chrg->chrg_bat_present(p_chrg) == 0) + puts("No battery detected\n"); + + p_bat = pmic_get("BAT_TRATS2"); + if (!p_bat) { + puts("BAT_TRATS2: Not found\n"); + return -ENODEV; + } + + p_fg->parent = p_bat; + p_chrg->parent = p_bat; + p_muic->parent = p_bat; + + p_bat->pbat->battery_init(p_bat, p_fg, p_chrg, p_muic); + + pb = p_bat->pbat; + chrg = p_muic->chrg->chrg_type(p_muic); + debug("CHARGER TYPE: %d\n", chrg); + + if (!p_chrg->chrg->chrg_bat_present(p_chrg)) { + puts("No battery detected\n"); + return -1; + } + + p_fg->fg->fg_battery_check(p_fg, p_bat); + + if (pb->bat->state == CHARGE && chrg == CHARGER_USB) + puts("CHARGE Battery !\n"); + + return 0; +} + +int dram_init(void) +{ + u32 size_mb; + + size_mb = (get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) + + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) + + get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) + + get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE)) >> 20; + + gd->ram_size = size_mb << 20; + + return 0; +} + +void dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + gd->bd->bi_dram[1].start = PHYS_SDRAM_2; + gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE; + gd->bd->bi_dram[2].start = PHYS_SDRAM_3; + gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE; + gd->bd->bi_dram[3].start = PHYS_SDRAM_4; + gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE; +} + +int board_mmc_init(bd_t *bis) +{ + int err0, err2 = 0; + + gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE; + + /* eMMC_EN: SD_0_CDn: GPK0[2] Output High */ + s5p_gpio_direction_output(&gpio2->k0, 2, 1); + s5p_gpio_set_pull(&gpio2->k0, 2, GPIO_PULL_NONE); + + /* + * eMMC GPIO: + * SDR 8-bit@48MHz at MMC0 + * GPK0[0] SD_0_CLK(2) + * GPK0[1] SD_0_CMD(2) + * GPK0[2] SD_0_CDn -> Not used + * GPK0[3:6] SD_0_DATA[0:3](2) + * GPK1[3:6] SD_0_DATA[0:3](3) + * + * DDR 4-bit@26MHz at MMC4 + * GPK0[0] SD_4_CLK(3) + * GPK0[1] SD_4_CMD(3) + * GPK0[2] SD_4_CDn -> Not used + * GPK0[3:6] SD_4_DATA[0:3](3) + * GPK1[3:6] SD_4_DATA[4:7](4) + */ + + err0 = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); + + /* + * MMC device init + * mmc0 : eMMC (8-bit buswidth) + * mmc2 : SD card (4-bit buswidth) + */ + if (err0) + debug("SDMMC0 not configured\n"); + else + err0 = s5p_mmc_init(0, 8); + + /* T-flash detect */ + s5p_gpio_cfg_pin(&gpio2->x3, 4, 0xf); + s5p_gpio_set_pull(&gpio2->x3, 4, GPIO_PULL_UP); + + /* + * Check the T-flash detect pin + * GPX3[4] T-flash detect pin + */ + if (!s5p_gpio_get_value(&gpio2->x3, 4)) { + err2 = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); + if (err2) + debug("SDMMC2 not configured\n"); + else + err2 = s5p_mmc_init(2, 4); + } + + return err0 & err2; +} + +static int pmic_init_max77686(void) +{ + struct pmic *p = pmic_get("MAX77686_PMIC"); + + if (pmic_probe(p)) + return -1; + + /* BUCK/LDO Output Voltage */ + max77686_set_ldo_voltage(p, 21, 2800000); /* LDO21 VTF_2.8V */ + max77686_set_ldo_voltage(p, 23, 3300000); /* LDO23 TSP_AVDD_3.3V*/ + max77686_set_ldo_voltage(p, 24, 1800000); /* LDO24 TSP_VDD_1.8V */ + + /* BUCK/LDO Output Mode */ + max77686_set_buck_mode(p, 1, OPMODE_STANDBY); /* BUCK1 VMIF_1.1V_AP */ + max77686_set_buck_mode(p, 2, OPMODE_ON); /* BUCK2 VARM_1.0V_AP */ + max77686_set_buck_mode(p, 3, OPMODE_ON); /* BUCK3 VINT_1.0V_AP */ + max77686_set_buck_mode(p, 4, OPMODE_ON); /* BUCK4 VG3D_1.0V_AP */ + max77686_set_buck_mode(p, 5, OPMODE_ON); /* BUCK5 VMEM_1.2V_AP */ + max77686_set_buck_mode(p, 6, OPMODE_ON); /* BUCK6 VCC_SUB_1.35V*/ + max77686_set_buck_mode(p, 7, OPMODE_ON); /* BUCK7 VCC_SUB_2.0V */ + max77686_set_buck_mode(p, 8, OPMODE_OFF); /* VMEM_VDDF_2.85V */ + max77686_set_buck_mode(p, 9, OPMODE_OFF); /* CAM_ISP_CORE_1.2V*/ + + max77686_set_ldo_mode(p, 1, OPMODE_LPM); /* LDO1 VALIVE_1.0V_AP*/ + max77686_set_ldo_mode(p, 2, OPMODE_STANDBY); /* LDO2 VM1M2_1.2V_AP */ + max77686_set_ldo_mode(p, 3, OPMODE_LPM); /* LDO3 VCC_1.8V_AP */ + max77686_set_ldo_mode(p, 4, OPMODE_LPM); /* LDO4 VCC_2.8V_AP */ + max77686_set_ldo_mode(p, 5, OPMODE_OFF); /* LDO5_VCC_1.8V_IO */ + max77686_set_ldo_mode(p, 6, OPMODE_STANDBY); /* LDO6 VMPLL_1.0V_AP */ + max77686_set_ldo_mode(p, 7, OPMODE_STANDBY); /* LDO7 VPLL_1.0V_AP */ + max77686_set_ldo_mode(p, 8, OPMODE_LPM); /* LDO8 VMIPI_1.0V_AP */ + max77686_set_ldo_mode(p, 9, OPMODE_OFF); /* CAM_ISP_MIPI_1.2*/ + max77686_set_ldo_mode(p, 10, OPMODE_LPM); /* LDO10 VMIPI_1.8V_AP*/ + max77686_set_ldo_mode(p, 11, OPMODE_STANDBY); /* LDO11 VABB1_1.8V_AP*/ + max77686_set_ldo_mode(p, 12, OPMODE_LPM); /* LDO12 VUOTG_3.0V_AP*/ + max77686_set_ldo_mode(p, 13, OPMODE_OFF); /* LDO13 VC2C_1.8V_AP */ + max77686_set_ldo_mode(p, 14, OPMODE_STANDBY); /* VABB02_1.8V_AP */ + max77686_set_ldo_mode(p, 15, OPMODE_STANDBY); /* LDO15 VHSIC_1.0V_AP*/ + max77686_set_ldo_mode(p, 16, OPMODE_STANDBY); /* LDO16 VHSIC_1.8V_AP*/ + max77686_set_ldo_mode(p, 17, OPMODE_OFF); /* CAM_SENSOR_CORE_1.2*/ + max77686_set_ldo_mode(p, 18, OPMODE_OFF); /* CAM_ISP_SEN_IO_1.8V*/ + max77686_set_ldo_mode(p, 19, OPMODE_OFF); /* LDO19 VT_CAM_1.8V */ + max77686_set_ldo_mode(p, 20, OPMODE_ON); /* LDO20 VDDQ_PRE_1.8V*/ + max77686_set_ldo_mode(p, 21, OPMODE_OFF); /* LDO21 VTF_2.8V */ + max77686_set_ldo_mode(p, 22, OPMODE_OFF); /* LDO22 VMEM_VDD_2.8V*/ + max77686_set_ldo_mode(p, 23, OPMODE_OFF); /* LDO23 TSP_AVDD_3.3V*/ + max77686_set_ldo_mode(p, 24, OPMODE_OFF); /* LDO24 TSP_VDD_1.8V */ + max77686_set_ldo_mode(p, 25, OPMODE_OFF); /* LDO25 VCC_3.3V_LCD */ + max77686_set_ldo_mode(p, 26, OPMODE_OFF); /*LDO26 VCC_3.0V_MOTOR*/ + + return 0; +} + +/* + * LCD + */ + +#ifdef CONFIG_LCD +static struct mipi_dsim_config dsim_config = { + .e_interface = DSIM_VIDEO, + .e_virtual_ch = DSIM_VIRTUAL_CH_0, + .e_pixel_format = DSIM_24BPP_888, + .e_burst_mode = DSIM_BURST_SYNC_EVENT, + .e_no_data_lane = DSIM_DATA_LANE_4, + .e_byte_clk = DSIM_PLL_OUT_DIV8, + .hfp = 1, + + .p = 3, + .m = 120, + .s = 1, + + /* D-PHY PLL stable time spec :min = 200usec ~ max 400usec */ + .pll_stable_time = 500, + + /* escape clk : 10MHz */ + .esc_clk = 20 * 1000000, + + /* stop state holding counter after bta change count 0 ~ 0xfff */ + .stop_holding_cnt = 0x7ff, + /* bta timeout 0 ~ 0xff */ + .bta_timeout = 0xff, + /* lp rx timeout 0 ~ 0xffff */ + .rx_timeout = 0xffff, +}; + +static struct exynos_platform_mipi_dsim dsim_platform_data = { + .lcd_panel_info = NULL, + .dsim_config = &dsim_config, +}; + +static struct mipi_dsim_lcd_device mipi_lcd_device = { + .name = "s6e8ax0", + .id = -1, + .bus_id = 0, + .platform_data = (void *)&dsim_platform_data, +}; + +static int mipi_power(void) +{ + struct pmic *p = pmic_get("MAX77686_PMIC"); + + /* LDO8 VMIPI_1.0V_AP */ + max77686_set_ldo_mode(p, 8, OPMODE_ON); + /* LDO10 VMIPI_1.8V_AP */ + max77686_set_ldo_mode(p, 10, OPMODE_ON); + + return 0; +} + +void exynos_lcd_power_on(void) +{ + struct pmic *p = pmic_get("MAX77686_PMIC"); + + gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE; + + /* LCD_2.2V_EN: GPC0[1] */ + s5p_gpio_set_pull(&gpio1->c0, 1, GPIO_PULL_UP); + s5p_gpio_direction_output(&gpio1->c0, 1, 1); + + /* LDO25 VCC_3.1V_LCD */ + pmic_probe(p); + max77686_set_ldo_voltage(p, 25, 3100000); + max77686_set_ldo_mode(p, 25, OPMODE_LPM); +} + +void exynos_reset_lcd(void) +{ + gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE; + + /* reset lcd */ + s5p_gpio_direction_output(&gpio1->f2, 1, 0); + udelay(10); + s5p_gpio_set_value(&gpio1->f2, 1, 1); +} + +vidinfo_t panel_info = { + .vl_freq = 60, + .vl_col = 720, + .vl_row = 1280, + .vl_width = 720, + .vl_height = 1280, + .vl_clkp = CONFIG_SYS_HIGH, + .vl_hsp = CONFIG_SYS_LOW, + .vl_vsp = CONFIG_SYS_LOW, + .vl_dp = CONFIG_SYS_LOW, + .vl_bpix = 5, /* Bits per pixel, 2^5 = 32 */ + + /* s6e8ax0 Panel infomation */ + .vl_hspw = 5, + .vl_hbpd = 10, + .vl_hfpd = 10, + + .vl_vspw = 2, + .vl_vbpd = 1, + .vl_vfpd = 13, + .vl_cmd_allow_len = 0xf, + .mipi_enabled = 1, + + .dual_lcd_enabled = 0, + + .init_delay = 0, + .power_on_delay = 25, + .reset_delay = 0, + .interface_mode = FIMD_RGB_INTERFACE, +}; + +void init_panel_info(vidinfo_t *vid) +{ + vid->logo_on = 1; + vid->resolution = HD_RESOLUTION; + vid->rgb_mode = MODE_RGB_P; + + vid->power_on_delay = 30; + + mipi_lcd_device.reverse_panel = 1; + +#ifdef CONFIG_TIZEN + get_tizen_logo_info(vid); +#endif + + strcpy(dsim_platform_data.lcd_panel_name, mipi_lcd_device.name); + dsim_platform_data.mipi_power = mipi_power; + dsim_platform_data.phy_enable = set_mipi_phy_ctrl; + dsim_platform_data.lcd_panel_info = (void *)vid; + exynos_mipi_dsi_register_lcd_device(&mipi_lcd_device); + + s6e8ax0_init(); + + exynos_set_dsim_platform_data(&dsim_platform_data); +} +#endif /* LCD */ + +#ifdef CONFIG_MISC_INIT_R +int misc_init_r(void) +{ + setenv("model", "GT-I8800"); + setenv("board", "TRATS2"); + + show_hw_revision(); + + return 0; +} +#endif diff --git a/boards.cfg b/boards.cfg index dbd8479e32..e6cc56e124 100644 --- a/boards.cfg +++ b/boards.cfg @@ -271,6 +271,7 @@ Active arm armv7 exynos samsung smdk5250 Active arm armv7 exynos samsung smdk5250 snow - Rajeshwari Shinde Active arm armv7 exynos samsung smdkv310 smdkv310 - Chander Kashyap Active arm armv7 exynos samsung trats trats - Lukasz Majewski +Active arm armv7 exynos samsung trats2 trats2 - Piotr Wilczek Active arm armv7 exynos samsung universal_c210 s5pc210_universal - Minkyu Kang Active arm armv7 highbank - highbank highbank - Rob Herring Active arm armv7 mx5 denx m53evk m53evk m53evk:IMX_CONFIG=board/denx/m53evk/imximage.cfg Marek Vasut diff --git a/include/configs/trats2.h b/include/configs/trats2.h new file mode 100644 index 0000000000..0e93836c0c --- /dev/null +++ b/include/configs/trats2.h @@ -0,0 +1,311 @@ +/* + * Copyright (C) 2013 Samsung Electronics + * Sanghee Kim + * Piotr Wilczek + * + * Configuation settings for the SAMSUNG TRATS2 (EXYNOS4412) board. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_SAMSUNG /* in a SAMSUNG core */ +#define CONFIG_S5P /* which is in a S5P Family */ +#define CONFIG_EXYNOS4 /* which is in a EXYNOS4XXX */ +#define CONFIG_TIZEN /* TIZEN lib */ + +#define PLATFORM_NO_UNALIGNED + +#include /* get chip and board defs */ + +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_SKIP_LOWLEVEL_INIT + +#define CONFIG_SYS_CACHELINE_SIZE 32 + +#ifndef CONFIG_SYS_L2CACHE_OFF +#define CONFIG_SYS_L2_PL310 +#define CONFIG_SYS_PL310_BASE 0x10502000 +#endif + +#define CONFIG_NR_DRAM_BANKS 4 +#define PHYS_SDRAM_1 0x40000000 /* LDDDR2 DMC 0 */ +#define PHYS_SDRAM_1_SIZE (256 << 20) /* 256 MB in CS 0 */ +#define PHYS_SDRAM_2 0x50000000 /* LPDDR2 DMC 1 */ +#define PHYS_SDRAM_2_SIZE (256 << 20) /* 256 MB in CS 0 */ +#define PHYS_SDRAM_3 0x60000000 /* LPDDR2 DMC 1 */ +#define PHYS_SDRAM_3_SIZE (256 << 20) /* 256 MB in CS 0 */ +#define PHYS_SDRAM_4 0x70000000 /* LPDDR2 DMC 1 */ +#define PHYS_SDRAM_4_SIZE (256 << 20) /* 256 MB in CS 0 */ +#define PHYS_SDRAM_END 0x80000000 + +#define CONFIG_SYS_MEM_TOP_HIDE (1 << 20) /* ram console */ + +#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1) +#define CONFIG_SYS_TEXT_BASE 0x78100000 + +#define CONFIG_SYS_CLK_FREQ 24000000 + +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_CMDLINE_TAG +#define CONFIG_REVISION_TAG + +/* MACH_TYPE_TRATS2 */ +#define MACH_TYPE_TRATS2 3765 +#define CONFIG_MACH_TYPE MACH_TYPE_TRATS2 + +#define CONFIG_DISPLAY_CPUINFO + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (2 << 20)) + +/* select serial console configuration */ +#define CONFIG_SERIAL2 + +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#define CONFIG_CMDLINE_EDITING + +#define CONFIG_BAUDRATE 115200 + +/* It should define before config_cmd_default.h */ +#define CONFIG_SYS_NO_FLASH + +/*********************************************************** + * Command definition + ***********************************************************/ +#include + +#undef CONFIG_CMD_ECHO +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_NAND +#undef CONFIG_CMD_MISC +#undef CONFIG_CMD_NFS +#undef CONFIG_CMD_SOURCE +#undef CONFIG_CMD_XIMG +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MMC +#define CONFIG_CMD_GPT +#define CONFIG_CMD_PMIC + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_ZERO_BOOTDELAY_CHECK + +#define CONFIG_CMD_FAT +#define CONFIG_FAT_WRITE + +/* EXT4 */ +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_EXT4_WRITE + +/* To use the TFTPBOOT over USB, Please enable the CONFIG_CMD_NET */ +#undef CONFIG_CMD_NET + +/* MMC */ +#define CONFIG_GENERIC_MMC +#define CONFIG_MMC +#define CONFIG_S5P_SDHCI +#define CONFIG_SDHCI +#define CONFIG_MMC_SDMA +#define CONFIG_MMC_DEFAULT_DEV 0 + +/* PWM */ +#define CONFIG_PWM + +#define CONFIG_BOOTARGS "Please use defined boot" +#define CONFIG_BOOTCOMMAND "run mmcboot" +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0" + +#define CONFIG_ENV_OVERWRITE +#define CONFIG_SYS_CONSOLE_INFO_QUIET +#define CONFIG_SYS_CONSOLE_IS_IN_ENV + +/* Tizen - partitions definitions */ +#define PARTS_CSA "csa-mmc" +#define PARTS_BOOTLOADER "u-boot" +#define PARTS_BOOT "boot" +#define PARTS_ROOT "platform" +#define PARTS_DATA "data" +#define PARTS_CSC "csc" +#define PARTS_UMS "ums" + +#define PARTS_DEFAULT \ + "uuid_disk=${uuid_gpt_disk};" \ + "name="PARTS_CSA",size=8MiB,uuid=${uuid_gpt_"PARTS_CSA"};" \ + "name="PARTS_BOOTLOADER",size=60MiB," \ + "uuid=${uuid_gpt_"PARTS_BOOTLOADER"};" \ + "name="PARTS_BOOT",size=100MiB,uuid=${uuid_gpt_"PARTS_BOOT"};" \ + "name="PARTS_ROOT",size=1GiB,uuid=${uuid_gpt_"PARTS_ROOT"};" \ + "name="PARTS_DATA",size=3GiB,uuid=${uuid_gpt_"PARTS_DATA"};" \ + "name="PARTS_CSC",size=150MiB,uuid=${uuid_gpt_"PARTS_CSC"};" \ + "name="PARTS_UMS",size=-,uuid=${uuid_gpt_"PARTS_UMS"}\0" \ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "bootk=" \ + "run loaddtb; run loaduimage; bootm 0x40007FC0 - ${fdtaddr}\0" \ + "updatemmc=" \ + "mmc boot 0 1 1 1; mmc write 0x42008000 0 0x200;" \ + "mmc boot 0 1 1 0\0" \ + "updatebackup=" \ + "mmc boot 0 1 1 2; mmc write 0x42100000 0 0x200;" \ + " mmc boot 0 1 1 0\0" \ + "updatebootb=" \ + "mmc read 0x51000000 0x80 0x200; run updatebackup\0" \ + "updateuboot=" \ + "mmc write 0x50000000 0x80 0x400\0" \ + "mmcboot=" \ + "setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \ + "${lpj} rootwait ${console} ${meminfo} ${opts} ${lcdinfo}; " \ + "run loaddtb; run loaduimage; bootm 0x40007FC0 - ${fdtaddr}\0" \ + "bootchart=set opts init=/sbin/bootchartd; run bootcmd\0" \ + "boottrace=setenv opts initcall_debug; run bootcmd\0" \ + "verify=n\0" \ + "rootfstype=ext4\0" \ + "console=" CONFIG_DEFAULT_CONSOLE \ + "kernelname=uImage\0" \ + "loaduimage=ext4load mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 uImage\0" \ + "0x40007FC0 ${kernelname}\0" \ + "loaddtb=ext4load mmc ${mmcdev}:${mmcbootpart} ${fdtaddr} " \ + "${fdtfile}\0" \ + "mmcdev=0\0" \ + "mmcbootpart=2\0" \ + "mmcrootpart=5\0" \ + "opts=always_resume=1\0" \ + "partitions=" PARTS_DEFAULT \ + "uartpath=ap\0" \ + "usbpath=ap\0" \ + "consoleon=set console console=ttySAC2,115200n8; save; reset\0" \ + "consoleoff=set console console=ram; save; reset\0" \ + "spladdr=0x40000100\0" \ + "splsize=0x200\0" \ + "splfile=falcon.bin\0" \ + "spl_export=" \ + "setexpr spl_imgsize ${splsize} + 8 ;" \ + "setenv spl_imgsize 0x${spl_imgsize};" \ + "setexpr spl_imgaddr ${spladdr} - 8 ;" \ + "setexpr spl_addr_tmp ${spladdr} - 4 ;" \ + "mw.b ${spl_imgaddr} 0x00 ${spl_imgsize};run loaduimage;" \ + "setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \ + "${lpj} rootwait ${console} ${meminfo} ${opts} ${lcdinfo};" \ + "spl export atags 0x40007FC0;" \ + "crc32 ${spladdr} ${splsize} ${spl_imgaddr};" \ + "mw.l ${spl_addr_tmp} ${splsize};" \ + "ext4write mmc ${mmcdev}:${mmcbootpart}" \ + " /${splfile} ${spl_imgaddr} ${spl_imgsize};" \ + "setenv spl_imgsize;" \ + "setenv spl_imgaddr;" \ + "setenv spl_addr_tmp;\0" \ + "fdtaddr=40800000\0" \ + "fdtfile=exynos4412-trats2.dtb\0" + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "Trats2 # " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE 384 /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ + +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/* memtest works on */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5000000) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x4800000) + +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR \ + - GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_HZ 1000 + +/* valid baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_SYS_MONITOR_BASE 0x00000000 + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ + +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV CONFIG_MMC_DEFAULT_DEV +#define CONFIG_ENV_SIZE 4096 +#define CONFIG_ENV_OFFSET ((32 - 4) << 10) /* 32KiB - 4KiB */ +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS + +#define CONFIG_MISC_INIT_R +#define CONFIG_BOARD_EARLY_INIT_F + +/* I2C */ +#include + +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x00 +#define I2C_SOFT_DECLARATIONS2 +#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x00 +#define I2C_SOFT_DECLARATIONS3 +#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x00 +#define CONFIG_SOFT_I2C_READ_REPEATED_START +#define CONFIG_SYS_I2C_INIT_BOARD +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SOFT_I2C_MULTI_BUS +#define CONFIG_SYS_MAX_I2C_BUS 15 + +#define CONFIG_SOFT_I2C_I2C5_SCL exynos4x12_gpio_part1_get_nr(d0, 3) +#define CONFIG_SOFT_I2C_I2C5_SDA exynos4x12_gpio_part1_get_nr(d0, 2) +#define CONFIG_SOFT_I2C_I2C9_SCL exynos4x12_gpio_part1_get_nr(f1, 4) +#define CONFIG_SOFT_I2C_I2C9_SDA exynos4x12_gpio_part1_get_nr(f1, 5) +#define CONFIG_SOFT_I2C_I2C10_SCL exynos4x12_gpio_part2_get_nr(m2, 1) +#define CONFIG_SOFT_I2C_I2C10_SDA exynos4x12_gpio_part2_get_nr(m2, 0) +#define CONFIG_SOFT_I2C_GPIO_SCL get_multi_scl_pin() +#define CONFIG_SOFT_I2C_GPIO_SDA get_multi_sda_pin() +#define I2C_INIT multi_i2c_init() + +/* POWER */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_MAX77686 +#define CONFIG_POWER_PMIC_MAX77693 +#define CONFIG_POWER_MUIC_MAX77693 +#define CONFIG_POWER_FG_MAX77693 +#define CONFIG_POWER_BATTERY_TRATS2 + +/* LCD */ +#define CONFIG_EXYNOS_FB +#define CONFIG_LCD +#define CONFIG_CMD_BMP +#define CONFIG_BMP_32BPP +#define CONFIG_FB_ADDR 0x52504000 +#define CONFIG_S6E8AX0 +#define CONFIG_EXYNOS_MIPI_DSIM +#define CONFIG_VIDEO_BMP_GZIP +#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((500 * 250 * 4) + (1 << 12)) + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 + +#endif /* __CONFIG_H */