From: Pali Rohár Date: Fri, 24 Sep 2021 14:11:56 +0000 (+0200) Subject: phy: marvell: a3700: Fix configuring polarity invert bits X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=4ca474d3067ba7278c6a5f94ff4340ca5a07ca0a;p=u-boot.git phy: marvell: a3700: Fix configuring polarity invert bits phy_txd_inv or phy_rxd_inv needs to be set only in case when appropriate polarity is inverted. Otherwise these bits should be cleared. Same change was included in TF-A project: https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9406 Signed-off-by: Pali Rohár Reviewed-by: Stefan Roese --- diff --git a/drivers/phy/marvell/comphy_a3700.c b/drivers/phy/marvell/comphy_a3700.c index 504f4b2bb1..69cd63edb1 100644 --- a/drivers/phy/marvell/comphy_a3700.c +++ b/drivers/phy/marvell/comphy_a3700.c @@ -230,9 +230,13 @@ static int comphy_pcie_power_up(u32 speed, u32 invert) */ if (invert & COMPHY_POLARITY_TXD_INVERT) reg_set16(phy_addr(PCIE, SYNC_PATTERN), phy_txd_inv, 0); + else + reg_set16(phy_addr(PCIE, SYNC_PATTERN), 0, phy_txd_inv); if (invert & COMPHY_POLARITY_RXD_INVERT) reg_set16(phy_addr(PCIE, SYNC_PATTERN), phy_rxd_inv, 0); + else + reg_set16(phy_addr(PCIE, SYNC_PATTERN), 0, phy_rxd_inv); /* * 11. Release SW reset @@ -467,9 +471,13 @@ static int comphy_usb3_power_up(u32 lane, u32 type, u32 speed, u32 invert) */ if (invert & COMPHY_POLARITY_TXD_INVERT) usb3_reg_set16(SYNC_PATTERN, phy_txd_inv, 0, lane); + else + usb3_reg_set16(SYNC_PATTERN, 0, phy_txd_inv, lane); if (invert & COMPHY_POLARITY_RXD_INVERT) usb3_reg_set16(SYNC_PATTERN, phy_rxd_inv, 0, lane); + else + usb3_reg_set16(SYNC_PATTERN, 0, phy_rxd_inv, lane); /* * 10. Set max speed generation to USB3.0 5Gbps @@ -839,9 +847,13 @@ static int comphy_sgmii_power_up(u32 lane, u32 speed, u32 invert) */ if (invert & COMPHY_POLARITY_TXD_INVERT) reg_set16(sgmiiphy_addr(lane, SYNC_PATTERN), phy_txd_inv, 0); + else + reg_set16(sgmiiphy_addr(lane, SYNC_PATTERN), 0, phy_txd_inv); if (invert & COMPHY_POLARITY_RXD_INVERT) reg_set16(sgmiiphy_addr(lane, SYNC_PATTERN), phy_rxd_inv, 0); + else + reg_set16(sgmiiphy_addr(lane, SYNC_PATTERN), 0, phy_rxd_inv); /* * 19. Set PHY input ports PIN_PU_PLL, PIN_PU_TX and PIN_PU_RX to 1