From: Ladislav Michl Date: Thu, 17 Aug 2017 01:06:45 +0000 (+0200) Subject: igep00x0: move SPL routines into separate file X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=4c699a4747e763e82cc813c955d318b966303b81;p=u-boot.git igep00x0: move SPL routines into separate file Avoid cluttering board file with CONFIG_SPL_BUILD ifdefs by moving SPL related functions into separate file. Signed-off-by: Ladislav Michl Tested-by: Pau Pajuelo Acked-by: Enric Balletbo i Serra --- diff --git a/board/isee/igep00x0/Makefile b/board/isee/igep00x0/Makefile index 68b151c3c5..74594da771 100644 --- a/board/isee/igep00x0/Makefile +++ b/board/isee/igep00x0/Makefile @@ -5,4 +5,8 @@ # SPDX-License-Identifier: GPL-2.0+ # -obj-y := igep00x0.o +ifdef CONFIG_SPL_BUILD +obj-y := spl.o common.o +else +obj-y := igep00x0.o common.o +endif diff --git a/board/isee/igep00x0/common.c b/board/isee/igep00x0/common.c new file mode 100644 index 0000000000..b8f1c14f6a --- /dev/null +++ b/board/isee/igep00x0/common.c @@ -0,0 +1,80 @@ +/* + * SPDX-License-Identifier: GPL-2.0+ + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include "igep00x0.h" + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Routine: set_muxconf_regs + * Description: Setting up the configuration Mux registers specific to the + * hardware. Many pins need to be moved from protect to primary + * mode. + */ +void set_muxconf_regs(void) +{ + MUX_DEFAULT(); + +#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020) + MUX_IGEP0020(); +#endif + +#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0030) + MUX_IGEP0030(); +#endif +} + +/* + * Routine: board_init + * Description: Early hardware init. + */ +int board_init(void) +{ + int loops = 100; + + /* find out flash memory type, assume NAND first */ + gpmc_cs0_flash = MTD_DEV_TYPE_NAND; + gpmc_init(); + + /* Issue a RESET and then READID */ + writeb(NAND_CMD_RESET, &gpmc_cfg->cs[0].nand_cmd); + writeb(NAND_CMD_STATUS, &gpmc_cfg->cs[0].nand_cmd); + while ((readl(&gpmc_cfg->cs[0].nand_dat) & NAND_STATUS_READY) + != NAND_STATUS_READY) { + udelay(1); + if (--loops == 0) { + gpmc_cs0_flash = MTD_DEV_TYPE_ONENAND; + gpmc_init(); /* reinitialize for OneNAND */ + break; + } + } + + /* boot param addr */ + gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100); + +#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE) + status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON); +#endif + + return 0; +} + +#if defined(CONFIG_MMC) +int board_mmc_init(bd_t *bis) +{ + return omap_mmc_init(0, 0, 0, -1, -1); +} + +void board_mmc_power_init(void) +{ + twl4030_power_mmc_init(0); +} +#endif diff --git a/board/isee/igep00x0/igep00x0.c b/board/isee/igep00x0/igep00x0.c index a7a75601dd..74f9bab093 100644 --- a/board/isee/igep00x0/igep00x0.c +++ b/board/isee/igep00x0/igep00x0.c @@ -20,15 +20,12 @@ #include #include #include -#include #include #include #include #include #include "igep00x0.h" -DECLARE_GLOBAL_DATA_PTR; - static const struct ns16550_platdata igep_serial = { .base = OMAP34XX_UART3, .reg_shift = 2, @@ -41,98 +38,6 @@ U_BOOT_DEVICE(igep_uart) = { &igep_serial }; -/* - * Routine: board_init - * Description: Early hardware init. - */ -int board_init(void) -{ - int loops = 100; - - /* find out flash memory type, assume NAND first */ - gpmc_cs0_flash = MTD_DEV_TYPE_NAND; - gpmc_init(); - - /* Issue a RESET and then READID */ - writeb(NAND_CMD_RESET, &gpmc_cfg->cs[0].nand_cmd); - writeb(NAND_CMD_STATUS, &gpmc_cfg->cs[0].nand_cmd); - while ((readl(&gpmc_cfg->cs[0].nand_dat) & NAND_STATUS_READY) - != NAND_STATUS_READY) { - udelay(1); - if (--loops == 0) { - gpmc_cs0_flash = MTD_DEV_TYPE_ONENAND; - gpmc_init(); /* reinitialize for OneNAND */ - break; - } - } - - /* boot param addr */ - gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100); - -#if defined(CONFIG_LED_STATUS) && defined(CONFIG_LED_STATUS_BOOT_ENABLE) - status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON); -#endif - - return 0; -} - -#ifdef CONFIG_SPL_BUILD -/* - * Routine: get_board_mem_timings - * Description: If we use SPL then there is no x-loader nor config header - * so we have to setup the DDR timings ourself on both banks. - */ -void get_board_mem_timings(struct board_sdrc_timings *timings) -{ - int mfr, id, err = identify_nand_chip(&mfr, &id); - - timings->mr = MICRON_V_MR_165; - if (!err) { - switch (mfr) { - case NAND_MFR_HYNIX: - timings->mcfg = HYNIX_V_MCFG_200(256 << 20); - timings->ctrla = HYNIX_V_ACTIMA_200; - timings->ctrlb = HYNIX_V_ACTIMB_200; - break; - case NAND_MFR_MICRON: - timings->mcfg = MICRON_V_MCFG_200(256 << 20); - timings->ctrla = MICRON_V_ACTIMA_200; - timings->ctrlb = MICRON_V_ACTIMB_200; - break; - default: - /* Should not happen... */ - break; - } - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz; - gpmc_cs0_flash = MTD_DEV_TYPE_NAND; - } else { - if (get_cpu_family() == CPU_OMAP34XX) { - timings->mcfg = NUMONYX_V_MCFG_165(256 << 20); - timings->ctrla = NUMONYX_V_ACTIMA_165; - timings->ctrlb = NUMONYX_V_ACTIMB_165; - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; - } else { - timings->mcfg = NUMONYX_V_MCFG_200(256 << 20); - timings->ctrla = NUMONYX_V_ACTIMA_200; - timings->ctrlb = NUMONYX_V_ACTIMB_200; - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz; - } - gpmc_cs0_flash = MTD_DEV_TYPE_ONENAND; - } -} - -#ifdef CONFIG_SPL_OS_BOOT -int spl_start_uboot(void) -{ - /* break into full u-boot on 'c' */ - if (serial_tstc() && serial_getc() == 'c') - return 1; - - return 0; -} -#endif -#endif - int onenand_board_init(struct mtd_info *mtd) { if (gpmc_cs0_flash == MTD_DEV_TYPE_ONENAND) { @@ -199,20 +104,6 @@ int board_eth_init(bd_t *bis) static inline void setup_net_chip(void) {} #endif -#if defined(CONFIG_MMC) -int board_mmc_init(bd_t *bis) -{ - return omap_mmc_init(0, 0, 0, -1, -1); -} -#endif - -#if defined(CONFIG_MMC) -void board_mmc_power_init(void) -{ - twl4030_power_mmc_init(0); -} -#endif - #ifdef CONFIG_OF_BOARD_SETUP static int ft_enable_by_compatible(void *blob, char *compat, int enable) { @@ -292,22 +183,3 @@ void board_mtdparts_default(const char **mtdids, const char **mtdparts) *mtdparts = parts; } } - -/* - * Routine: set_muxconf_regs - * Description: Setting up the configuration Mux registers specific to the - * hardware. Many pins need to be moved from protect to primary - * mode. - */ -void set_muxconf_regs(void) -{ - MUX_DEFAULT(); - -#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020) - MUX_IGEP0020(); -#endif - -#if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0030) - MUX_IGEP0030(); -#endif -} diff --git a/board/isee/igep00x0/spl.c b/board/isee/igep00x0/spl.c new file mode 100644 index 0000000000..eb705cbe88 --- /dev/null +++ b/board/isee/igep00x0/spl.c @@ -0,0 +1,64 @@ +/* + * SPDX-License-Identifier: GPL-2.0+ + */ +#include +#include +#include +#include +#include +#include "igep00x0.h" + +/* + * Routine: get_board_mem_timings + * Description: If we use SPL then there is no x-loader nor config header + * so we have to setup the DDR timings ourself on both banks. + */ +void get_board_mem_timings(struct board_sdrc_timings *timings) +{ + int mfr, id, err = identify_nand_chip(&mfr, &id); + + timings->mr = MICRON_V_MR_165; + if (!err) { + switch (mfr) { + case NAND_MFR_HYNIX: + timings->mcfg = HYNIX_V_MCFG_200(256 << 20); + timings->ctrla = HYNIX_V_ACTIMA_200; + timings->ctrlb = HYNIX_V_ACTIMB_200; + break; + case NAND_MFR_MICRON: + timings->mcfg = MICRON_V_MCFG_200(256 << 20); + timings->ctrla = MICRON_V_ACTIMA_200; + timings->ctrlb = MICRON_V_ACTIMB_200; + break; + default: + /* Should not happen... */ + break; + } + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz; + gpmc_cs0_flash = MTD_DEV_TYPE_NAND; + } else { + if (get_cpu_family() == CPU_OMAP34XX) { + timings->mcfg = NUMONYX_V_MCFG_165(256 << 20); + timings->ctrla = NUMONYX_V_ACTIMA_165; + timings->ctrlb = NUMONYX_V_ACTIMB_165; + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; + } else { + timings->mcfg = NUMONYX_V_MCFG_200(256 << 20); + timings->ctrla = NUMONYX_V_ACTIMA_200; + timings->ctrlb = NUMONYX_V_ACTIMB_200; + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz; + } + gpmc_cs0_flash = MTD_DEV_TYPE_ONENAND; + } +} + +#ifdef CONFIG_SPL_OS_BOOT +int spl_start_uboot(void) +{ + /* break into full u-boot on 'c' */ + if (serial_tstc() && serial_getc() == 'c') + return 1; + + return 0; +} +#endif