From: Niklaus Giger Date: Wed, 16 Jan 2008 17:37:50 +0000 (+0100) Subject: ppc4xx: Netstal HCU4 board. Added POST. Various fixes X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=4bd5036e60afac37e484c2d35cbbe7f6cc1623e7;p=u-boot.git ppc4xx: Netstal HCU4 board. Added POST. Various fixes - Various fixes - Reduced rom_size from 384 to 320 kB - Environment is now in flash - Added POST - Support for OF Signed-off-by: Niklaus Giger --- diff --git a/board/netstal/hcu4/config.mk b/board/netstal/hcu4/config.mk index 376609ab0d..580f18cb2e 100644 --- a/board/netstal/hcu4/config.mk +++ b/board/netstal/hcu4/config.mk @@ -21,7 +21,7 @@ # Netstal Maschinen AG: HCU4 boards # -TEXT_BASE = 0xFFFa0000 +TEXT_BASE = 0xFFFB0000 ifeq ($(debug),1) PLATFORM_CPPFLAGS += -DDEBUG -g diff --git a/include/configs/hcu4.h b/include/configs/hcu4.h index b43b228fba..cb51406cb7 100644 --- a/include/configs/hcu4.h +++ b/include/configs/hcu4.h @@ -46,8 +46,8 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ +#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */ +#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ @@ -67,7 +67,7 @@ #define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR /*----------------------------------------------------------------------- * Serial Port @@ -82,8 +82,8 @@ * set Linux BASE_BAUD to 403200. */ #undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ -#undef CONFIG_SERIAL_MULTI /* needed to be able to define - CONFIG_SERIAL_SOFTWARE_FIFO */ +#define CONFIG_SERIAL_MULTI 1 +/* needed to be able to define CONFIG_SERIAL_SOFTWARE_FIFO */ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 @@ -100,13 +100,24 @@ #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} +/*----------------------------------------------------------------------- + * Flash + *----------------------------------------------------------------------*/ + +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ #undef CFG_ENV_IS_IN_NVRAM -#undef CFG_ENV_IS_IN_FLASH -#define CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_IS_IN_FLASH #undef CFG_ENV_IS_NOWHERE #ifdef CFG_ENV_IS_IN_EEPROM @@ -120,7 +131,7 @@ /* Put the environment in Flash */ #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ #define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ +#define CFG_ENV_SIZE 8*1024 /* 8 KB Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) @@ -158,7 +169,7 @@ /* Setup some board specific values for the default environment variables */ #define CONFIG_HOSTNAME hcu4 -#define CONFIG_IPADDR 172.25.1.42 +#define CONFIG_IPADDR 172.25.1.99 #define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */ #define CONFIG_OVERWRITE_ETHADDR_ONCE #define CONFIG_SERVERIP 172.25.1.3 @@ -180,21 +191,17 @@ "rootpath=/home/diagnose/eldk/ppc_4xx\0" \ "bootfile=/tftpboot/hcu4/uImage\0" \ "load=tftp 100000 hcu4/u-boot.bin\0" \ - "update=protect off FFFa0000 FFFFFFFF;era FFFa0000 FFFFFFFF;" \ - "cp.b 100000 FFFa0000 60000\0" \ + "update=protect off FFFB0000 FFFFFFFF;era FFFC0000 FFFFFFFF;" \ + "cp.b 100000 FFFB0000 50000\0" \ "upd=run load;run update\0" \ "vx=tftp ${loadaddr} hcu4_vx_rom;" \ - "setenv bootargs emac(0,0)hcu4_vx_rom e=${ipaddr} " \ - " h=${serverip} u=dpu pw=netstal8752 tn=hcu4 f=0x3008;" \ + "vx=tftp ${loadaddr} hcu4/hcu4_vx_rom;" \ + "setenv bootargs emac(0,0)c:hcu4/hcu4_vx_rom e=${ipaddr} " \ "bootvx ${loadaddr}\0" \ "" #define CONFIG_BOOTCOMMAND "run vx" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ @@ -202,10 +209,10 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_HAS_ETH0 -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ +#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & desC */ /* * BOOTP options @@ -221,7 +228,6 @@ #include #define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BSP #define CONFIG_CMD_CACHE #define CONFIG_CMD_DHCP #define CONFIG_CMD_DIAG @@ -241,15 +247,30 @@ #define CONFIG_SPD_EEPROM 1 #define SPD_EEPROM_ADDRESS 0x50 +/* POST support */ +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CPU | \ + CFG_POST_UART | \ + CFG_POST_I2C | \ + CFG_POST_CACHE | \ + CFG_POST_ETHER | \ + CFG_POST_SPR) + +#define CFG_POST_UART_TABLE {UART0_BASE} +#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) +#undef CONFIG_LOGBUFFER +#define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */ +#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ + /*----------------------------------------------------------------------- * Miscellaneous configurable options *----------------------------------------------------------------------*/ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ @@ -266,47 +287,40 @@ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ -/* Memory Bank 0 (Flash Bank 0) initialization */ -#define CFG_EBC_PB0AP 0x02005400 -#define CFG_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */ +#define CFG_EBC_CFG 0x98400000 -#define CFG_EBC_PB1AP 0x03041200 -#define CFG_EBC_PB1CR 0x7009A000 /* BAS=,BS=MB,BU=R/W,BW=bit */ +/* Memory Bank 0 (Flash Bank 0) initialization */ +#define CFG_EBC_PB0AP 0x02005400 +#define CFG_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */ -#define CFG_EBC_PB2AP 0x02054500 -#define CFG_EBC_PB2CR 0x78018000 /* BAS=,BS=MB,BU=R/W,BW=bit */ +#define CFG_EBC_PB1AP 0x03041200 +#define CFG_EBC_PB1CR 0x7009A000 /* BAS=,BS=MB,BU=R/W,BW=bit */ -#define CFG_EBC_PB3AP 0x01840300 -#define CFG_EBC_PB3CR 0x7c0ba000 /* BAS=,BS=MB,BU=R/W,BW=bit */ +#define CFG_EBC_PB2AP 0x02054500 +#define CFG_EBC_PB2CR 0x78018000 /* BAS=,BS=MB,BU=R/W,BW=bit */ -#define CFG_EBC_PB4AP 0x01800300 -#define CFG_EBC_PB4CR 0x7e0ba000 /* BAS=,BS=MB,BU=R/W,BW=bit */ +#define CFG_EBC_PB3AP 0x01840300 +#define CFG_EBC_PB3CR 0x7c0ba000 /* BAS=,BS=MB,BU=R/W,BW=bit */ -#define CFG_GPIO0_TCR 0x7ffe0000 /* GPIO value */ +#define CFG_EBC_PB4AP 0x01800300 +#define CFG_EBC_PB4CR 0x7e0ba000 /* BAS=,BS=MB,BU=R/W,BW=bit */ + +#define CFG_GPIO0_OR 0xF27FFFFF /* GPIO value */ +#define CFG_GPIO0_TCR 0x7FFE0000 /* GPIO value */ +#define CFG_GPIO0_ODR 0x00E897FC /* GPIO value */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - - -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CFG_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */ /* Init Memory Controller: * @@ -326,8 +340,8 @@ * * Boot Flags */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ #define CFG_HUSH_PARSER /* use "hush" command parser */ #ifdef CFG_HUSH_PARSER @@ -338,4 +352,9 @@ #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + #endif /* __CONFIG_H */