From: Kumar Gala Date: Fri, 9 Jul 2010 05:02:34 +0000 (-0500) Subject: powerpc/86xx: Rename PCI1/2 to PCIE1/2 on MPC8641HPCN & SBC8641 X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=46f3e3851dac0c4acecf4192d8e13c8521ce98b4;p=u-boot.git powerpc/86xx: Rename PCI1/2 to PCIE1/2 on MPC8641HPCN & SBC8641 The MPC8641 boards actually only have PCIE not PCI. Rename so we are uniform with regards to names so we can replace this code with templated code. Signed-off-by: Kumar Gala --- diff --git a/board/freescale/mpc8641hpcn/law.c b/board/freescale/mpc8641hpcn/law.c index bd357b8667..8c8ce9585a 100644 --- a/board/freescale/mpc8641hpcn/law.c +++ b/board/freescale/mpc8641hpcn/law.c @@ -1,5 +1,5 @@ /* - * Copyright 2008 Freescale Semiconductor, Inc. + * Copyright 2008,2010 Freescale Semiconductor, Inc. * * (C) Copyright 2000 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. @@ -32,14 +32,14 @@ * * 0x0000_0000 0x7fff_ffff DDR 2G * if PCI (prepend 0xc_0000_0000 if CONFIG_PHYS_64BIT) - * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M - * 0xa000_0000 0xbfff_ffff PCI2 MEM 512M + * 0x8000_0000 0x9fff_ffff PCIE1 MEM 512M + * 0xa000_0000 0xbfff_ffff PCIE2 MEM 512M * else if RIO (prepend 0xc_0000_0000 if CONFIG_PHYS_64BIT) * 0x8000_0000 0x9fff_ffff RapidIO 512M * endif * (prepend 0xf_0000_0000 if CONFIG_PHYS_64BIT) - * 0xffc0_0000 0xffc0_ffff PCI1 IO 64K - * 0xffc1_0000 0xffc1_ffff PCI2 IO 64K + * 0xffc0_0000 0xffc0_ffff PCIE1 IO 64K + * 0xffc1_0000 0xffc1_ffff PCIE2 IO 64K * 0xffe0_0000 0xffef_ffff CCSRBAR 1M * 0xffdf_0000 0xffe0_0000 PIXIS, CF 64K * 0xef80_0000 0xefff_ffff FLASH (boot bank) 8M @@ -54,10 +54,10 @@ struct law_entry law_table[] = { SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR_1), #endif #ifdef CONFIG_PCI - SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1), - SET_LAW(CONFIG_SYS_PCI2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2), - SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_1), - SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_2), + SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1), + SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2), + SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_1), + SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCI_2), #elif defined(CONFIG_RIO) SET_LAW(CONFIG_SYS_RIO_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_RIO), #endif diff --git a/board/freescale/mpc8641hpcn/mpc8641hpcn.c b/board/freescale/mpc8641hpcn/mpc8641hpcn.c index 9e881024fe..a88be5a0d6 100644 --- a/board/freescale/mpc8641hpcn/mpc8641hpcn.c +++ b/board/freescale/mpc8641hpcn/mpc8641hpcn.c @@ -1,5 +1,5 @@ /* - * Copyright 2006, 2007 Freescale Semiconductor. + * Copyright 2006, 2007, 2010 Freescale Semiconductor. * * See file CREDITS for list of people who contributed to this * project. @@ -129,21 +129,21 @@ fixed_sdram(void) #if defined(CONFIG_PCI) -static struct pci_controller pci1_hose; +static struct pci_controller pcie1_hose; #endif /* CONFIG_PCI */ -#ifdef CONFIG_PCI2 -static struct pci_controller pci2_hose; -#endif /* CONFIG_PCI2 */ +#ifdef CONFIG_PCIE2 +static struct pci_controller pcie2_hose; +#endif /* CONFIG_PCIE2 */ int first_free_busno = 0; void pci_init_board(void) { -#ifdef CONFIG_PCI1 +#ifdef CONFIG_PCIE1 { volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR; - struct pci_controller *hose = &pci1_hose; + struct pci_controller *hose = &pcie1_hose; struct pci_region *r = hose->regions; volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR; volatile ccsr_gur_t *gur = &immap->im_gur; @@ -169,16 +169,16 @@ void pci_init_board(void) /* outbound memory */ pci_set_region(r++, - CONFIG_SYS_PCI1_MEM_BUS, - CONFIG_SYS_PCI1_MEM_PHYS, - CONFIG_SYS_PCI1_MEM_SIZE, + CONFIG_SYS_PCIE1_MEM_BUS, + CONFIG_SYS_PCIE1_MEM_PHYS, + CONFIG_SYS_PCIE1_MEM_SIZE, PCI_REGION_MEM); /* outbound io */ pci_set_region(r++, - CONFIG_SYS_PCI1_IO_BUS, - CONFIG_SYS_PCI1_IO_PHYS, - CONFIG_SYS_PCI1_IO_SIZE, + CONFIG_SYS_PCIE1_IO_BUS, + CONFIG_SYS_PCIE1_IO_PHYS, + CONFIG_SYS_PCIE1_IO_SIZE, PCI_REGION_IO); hose->region_count = r - hose->regions; @@ -195,8 +195,8 @@ void pci_init_board(void) * Activate ULI1575 legacy chip by performing a fake * memory access. Needed to make ULI RTC work. */ - in_be32((unsigned *) ((char *)(CONFIG_SYS_PCI1_MEM_VIRT - + CONFIG_SYS_PCI1_MEM_SIZE - 0x1000000))); + in_be32((unsigned *) ((char *)(CONFIG_SYS_PCIE1_MEM_VIRT + + CONFIG_SYS_PCIE1_MEM_SIZE - 0x1000000))); } else { puts("PCI-EXPRESS 1: Disabled\n"); @@ -204,26 +204,26 @@ void pci_init_board(void) } #else puts("PCI-EXPRESS1: Disabled\n"); -#endif /* CONFIG_PCI1 */ +#endif /* CONFIG_PCIE1 */ -#ifdef CONFIG_PCI2 +#ifdef CONFIG_PCIE2 { volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR; - struct pci_controller *hose = &pci2_hose; + struct pci_controller *hose = &pcie2_hose; struct pci_region *r = hose->regions; /* outbound memory */ pci_set_region(r++, - CONFIG_SYS_PCI2_MEM_BUS, - CONFIG_SYS_PCI2_MEM_PHYS, - CONFIG_SYS_PCI2_MEM_SIZE, + CONFIG_SYS_PCIE2_MEM_BUS, + CONFIG_SYS_PCIE2_MEM_PHYS, + CONFIG_SYS_PCIE2_MEM_SIZE, PCI_REGION_MEM); /* outbound io */ pci_set_region(r++, - CONFIG_SYS_PCI2_IO_BUS, - CONFIG_SYS_PCI2_IO_PHYS, - CONFIG_SYS_PCI2_IO_SIZE, + CONFIG_SYS_PCIE2_IO_BUS, + CONFIG_SYS_PCIE2_IO_PHYS, + CONFIG_SYS_PCIE2_IO_SIZE, PCI_REGION_IO); hose->region_count = r - hose->regions; @@ -238,7 +238,7 @@ void pci_init_board(void) } #else puts("PCI-EXPRESS 2: Disabled\n"); -#endif /* CONFIG_PCI2 */ +#endif /* CONFIG_PCIE2 */ } @@ -253,11 +253,11 @@ ft_board_setup(void *blob, bd_t *bd) ft_cpu_setup(blob, bd); -#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); +#ifdef CONFIG_PCIE1 + ft_fsl_pci_setup(blob, "pci0", &pcie1_hose); #endif -#ifdef CONFIG_PCI2 - ft_fsl_pci_setup(blob, "pci1", &pci2_hose); +#ifdef CONFIG_PCIE2 + ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); #endif /* diff --git a/board/sbc8641d/law.c b/board/sbc8641d/law.c index d20fa51c3d..705e1c2964 100644 --- a/board/sbc8641d/law.c +++ b/board/sbc8641d/law.c @@ -32,11 +32,11 @@ * * 0x0000_0000 DDR 256M * 0x1000_0000 DDR2 256M - * 0x8000_0000 PCI1 MEM 512M - * 0xa000_0000 PCI2 MEM 512M + * 0x8000_0000 PCIE1 MEM 512M + * 0xa000_0000 PCIE2 MEM 512M * 0xc000_0000 RapidIO 512M - * 0xe200_0000 PCI1 IO 16M - * 0xe300_0000 PCI2 IO 16M + * 0xe200_0000 PCIE1 IO 16M + * 0xe300_0000 PCIE2 IO 16M * 0xf800_0000 CCSRBAR 2M * 0xfe00_0000 FLASH (boot bank) 32M * @@ -49,11 +49,11 @@ struct law_entry law_table[] = { SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000, LAW_SIZE_256M, LAW_TRGT_IF_DDR_2), #endif - SET_LAW(CONFIG_SYS_PCI1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1), - SET_LAW(CONFIG_SYS_PCI2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2), + SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_1), + SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCI_2), SET_LAW(0xf8000000, LAW_SIZE_2M, LAW_TRGT_IF_LBC), - SET_LAW(CONFIG_SYS_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_1), - SET_LAW(CONFIG_SYS_PCI2_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_2), + SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_1), + SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI_2), SET_LAW(0xfe000000, LAW_SIZE_32M, LAW_TRGT_IF_LBC), SET_LAW(CONFIG_SYS_RIO_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_RIO) }; diff --git a/board/sbc8641d/sbc8641d.c b/board/sbc8641d/sbc8641d.c index 1060f3883c..b1dda1082b 100644 --- a/board/sbc8641d/sbc8641d.c +++ b/board/sbc8641d/sbc8641d.c @@ -191,16 +191,16 @@ static struct pci_config_table pci_fsl86xxads_config_table[] = { }; #endif -static struct pci_controller pci1_hose = { +static struct pci_controller pcie1_hose = { #ifndef CONFIG_PCI_PNP config_table:pci_mpc86xxcts_config_table #endif }; #endif /* CONFIG_PCI */ -#ifdef CONFIG_PCI2 -static struct pci_controller pci2_hose; -#endif /* CONFIG_PCI2 */ +#ifdef CONFIG_PCIE2 +static struct pci_controller pcie2_hose; +#endif /* CONFIG_PCIE2 */ int first_free_busno = 0; @@ -212,10 +212,10 @@ void pci_init_board(void) uint io_sel = (gur->pordevsr & MPC8641_PORDEVSR_IO_SEL) >> MPC8641_PORDEVSR_IO_SEL_SHIFT; -#ifdef CONFIG_PCI1 +#ifdef CONFIG_PCIE1 { volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR; - struct pci_controller *hose = &pci1_hose; + struct pci_controller *hose = &pcie1_hose; struct pci_region *r = hose->regions; #ifdef DEBUG uint host1_agent = (gur->porbmsr & MPC8641_PORBMSR_HA) @@ -236,16 +236,16 @@ void pci_init_board(void) /* outbound memory */ pci_set_region(r++, - CONFIG_SYS_PCI1_MEM_BUS, - CONFIG_SYS_PCI1_MEM_PHYS, - CONFIG_SYS_PCI1_MEM_SIZE, + CONFIG_SYS_PCIE1_MEM_BUS, + CONFIG_SYS_PCIE1_MEM_PHYS, + CONFIG_SYS_PCIE1_MEM_SIZE, PCI_REGION_MEM); /* outbound io */ pci_set_region(r++, - CONFIG_SYS_PCI1_IO_BUS, - CONFIG_SYS_PCI1_IO_PHYS, - CONFIG_SYS_PCI1_IO_SIZE, + CONFIG_SYS_PCIE1_IO_BUS, + CONFIG_SYS_PCIE1_IO_PHYS, + CONFIG_SYS_PCIE1_IO_SIZE, PCI_REGION_IO); hose->region_count = r - hose->regions; @@ -264,26 +264,26 @@ void pci_init_board(void) } #else puts("PCI-EXPRESS1: Disabled\n"); -#endif /* CONFIG_PCI1 */ +#endif /* CONFIG_PCIE1 */ -#ifdef CONFIG_PCI2 +#ifdef CONFIG_PCIE2 { volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR; - struct pci_controller *hose = &pci2_hose; + struct pci_controller *hose = &pcie2_hose; struct pci_region *r = hose->regions; /* outbound memory */ pci_set_region(r++, - CONFIG_SYS_PCI2_MEM_BUS, - CONFIG_SYS_PCI2_MEM_PHYS, - CONFIG_SYS_PCI2_MEM_SIZE, + CONFIG_SYS_PCIE2_MEM_BUS, + CONFIG_SYS_PCIE2_MEM_PHYS, + CONFIG_SYS_PCIE2_MEM_SIZE, PCI_REGION_MEM); /* outbound io */ pci_set_region(r++, - CONFIG_SYS_PCI2_IO_BUS, - CONFIG_SYS_PCI2_IO_PHYS, - CONFIG_SYS_PCI2_IO_SIZE, + CONFIG_SYS_PCIE2_IO_BUS, + CONFIG_SYS_PCIE2_IO_PHYS, + CONFIG_SYS_PCIE2_IO_SIZE, PCI_REGION_IO); hose->region_count = r - hose->regions; @@ -298,7 +298,7 @@ void pci_init_board(void) } #else puts("PCI-EXPRESS 2: Disabled\n"); -#endif /* CONFIG_PCI2 */ +#endif /* CONFIG_PCIE2 */ } @@ -308,11 +308,11 @@ void ft_board_setup (void *blob, bd_t *bd) { ft_cpu_setup(blob, bd); -#ifdef CONFIG_PCI1 - ft_fsl_pci_setup(blob, "pci0", &pci1_hose); +#ifdef CONFIG_PCIE1 + ft_fsl_pci_setup(blob, "pci0", &pcie1_hose); #endif -#ifdef CONFIG_PCI2 - ft_fsl_pci_setup(blob, "pci1", &pci2_hose); +#ifdef CONFIG_PCIE2 + ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); #endif } #endif diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index b183e027e5..0d1f7799cf 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -1,5 +1,5 @@ /* - * Copyright 2006 Freescale Semiconductor. + * Copyright 2006, 2010 Freescale Semiconductor. * * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) * @@ -58,8 +58,8 @@ #ifndef CONFIG_RIO /* RIO/PCI are mutually exclusive */ #define CONFIG_PCI 1 /* Enable PCI/PCIE */ -#define CONFIG_PCI1 1 /* PCIE controler 1 (ULI bridge) */ -#define CONFIG_PCI2 1 /* PCIE controler 2 (slot) */ +#define CONFIG_PCIE1 1 /* PCIE controler 1 (ULI bridge) */ +#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot) */ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #endif @@ -325,43 +325,43 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); * Addresses are mapped 1-1. */ -#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCI1_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCI1_MEM_PHYS 0x0000000c00000000ULL +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0x0000000c00000000ULL #else -#define CONFIG_SYS_PCI1_MEM_BUS CONFIG_SYS_PCI1_MEM_VIRT -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_VIRT +#define CONFIG_SYS_PCIE1_MEM_BUS CONFIG_SYS_PCIE1_MEM_VIRT +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_VIRT #endif -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_VIRT 0xffc00000 -#define CONFIG_SYS_PCI1_IO_PHYS (CONFIG_SYS_PCI1_IO_VIRT \ +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE1_IO_PHYS (CONFIG_SYS_PCIE1_IO_VIRT \ | CONFIG_SYS_PHYS_ADDR_HIGH) -#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64K */ +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ #ifdef CONFIG_PHYS_64BIT /* - * Use the same PCI bus address on PCI1 and PCI2 if we have PHYS_64BIT. + * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT. * This will increase the amount of PCI address space available for * for mapping RAM. */ -#define CONFIG_SYS_PCI2_MEM_BUS CONFIG_SYS_PCI1_MEM_BUS +#define CONFIG_SYS_PCIE2_MEM_BUS CONFIG_SYS_PCIE1_MEM_BUS #else -#define CONFIG_SYS_PCI2_MEM_BUS (CONFIG_SYS_PCI1_MEM_BUS \ - + CONFIG_SYS_PCI1_MEM_SIZE) +#define CONFIG_SYS_PCIE2_MEM_BUS (CONFIG_SYS_PCIE1_MEM_BUS \ + + CONFIG_SYS_PCIE1_MEM_SIZE) #endif -#define CONFIG_SYS_PCI2_MEM_VIRT (CONFIG_SYS_PCI1_MEM_VIRT \ - + CONFIG_SYS_PCI1_MEM_SIZE) -#define CONFIG_SYS_PCI2_MEM_PHYS (CONFIG_SYS_PCI1_MEM_PHYS \ - + CONFIG_SYS_PCI1_MEM_SIZE) -#define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI2_IO_VIRT (CONFIG_SYS_PCI1_IO_VIRT \ - + CONFIG_SYS_PCI1_IO_SIZE) -#define CONFIG_SYS_PCI2_IO_PHYS (CONFIG_SYS_PCI1_IO_PHYS \ - + CONFIG_SYS_PCI1_IO_SIZE) -#define CONFIG_SYS_PCI2_IO_SIZE CONFIG_SYS_PCI1_IO_SIZE +#define CONFIG_SYS_PCIE2_MEM_VIRT (CONFIG_SYS_PCIE1_MEM_VIRT \ + + CONFIG_SYS_PCIE1_MEM_SIZE) +#define CONFIG_SYS_PCIE2_MEM_PHYS (CONFIG_SYS_PCIE1_MEM_PHYS \ + + CONFIG_SYS_PCIE1_MEM_SIZE) +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_VIRT (CONFIG_SYS_PCIE1_IO_VIRT \ + + CONFIG_SYS_PCIE1_IO_SIZE) +#define CONFIG_SYS_PCIE2_IO_PHYS (CONFIG_SYS_PCIE1_IO_PHYS \ + + CONFIG_SYS_PCIE1_IO_SIZE) +#define CONFIG_SYS_PCIE2_IO_SIZE CONFIG_SYS_PCIE1_IO_SIZE #if defined(CONFIG_PCI) @@ -390,10 +390,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 /*PCIE video card used*/ -#define VIDEO_IO_OFFSET CONFIG_SYS_PCI2_IO_VIRT +#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT /*PCI video card used*/ -/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/ +/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT*/ /* video */ #define CONFIG_VIDEO @@ -406,7 +406,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_ATI_RADEON_FB #define CONFIG_VIDEO_LOGO /*#define CONFIG_CONSOLE_CURSOR*/ -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCI2_IO_VIRT +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT #endif #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ @@ -422,8 +422,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE #endif -#define CONFIG_MPC86XX_PCI2 - #endif /* CONFIG_PCI */ #if defined(CONFIG_TSEC_ENET) @@ -494,17 +492,17 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U /* if CONFIG_PCI: - * BAT2 PCI1 and PCI1 MEM + * BAT2 PCIE1 and PCIE1 MEM * if CONFIG_RIO * BAT2 Rapidio Memory */ #ifdef CONFIG_PCI -#define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_MEM_PHYS) \ +#define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS) \ | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G \ +#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \ | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_MEM_PHYS) \ +#define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS) \ | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U #else /* CONFIG_RIO */ @@ -553,14 +551,14 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #endif /* - * BAT4 PCI1_IO and PCI2_IO + * BAT4 PCIE1_IO and PCIE2_IO */ -#define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_IO_PHYS) \ +#define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS) \ | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_128K \ +#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \ | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_IO_PHYS) \ +#define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS) \ | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index 6662bbe0e5..618513ab66 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -56,8 +56,8 @@ #define CONFIG_SYS_SCRATCH_VA 0xe8000000 #define CONFIG_PCI 1 /* Enable PCIE */ -#define CONFIG_PCI1 1 /* PCIE controler 1 (slot 1) */ -#define CONFIG_PCI2 1 /* PCIE controler 2 (slot 2) */ +#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ +#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ @@ -304,23 +304,23 @@ * General PCI * Addresses are mapped 1-1. */ -#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS -#define CONFIG_SYS_PCI1_MEM_VIRT CONFIG_SYS_PCI1_MEM_BUS -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_BUS 0xe2000000 -#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BUS -#define CONFIG_SYS_PCI1_IO_VIRT CONFIG_SYS_PCI1_IO_BUS -#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */ - -#define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BUS -#define CONFIG_SYS_PCI2_MEM_VIRT CONFIG_SYS_PCI2_MEM_BUS -#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI2_IO_BUS 0xe3000000 -#define CONFIG_SYS_PCI2_IO_PHYS CONFIG_SYS_PCI2_IO_BUS -#define CONFIG_SYS_PCI2_IO_VIRT CONFIG_SYS_PCI2_IO_BUS -#define CONFIG_SYS_PCI2_IO_SIZE 0x1000000 /* 16M */ +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS +#define CONFIG_SYS_PCIE1_MEM_VIRT CONFIG_SYS_PCIE1_MEM_BUS +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_BUS 0xe2000000 +#define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_BUS +#define CONFIG_SYS_PCIE1_IO_VIRT CONFIG_SYS_PCIE1_IO_BUS +#define CONFIG_SYS_PCIE1_IO_SIZE 0x1000000 /* 16M */ + +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS +#define CONFIG_SYS_PCIE2_MEM_VIRT CONFIG_SYS_PCIE2_MEM_BUS +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCIE2_IO_BUS 0xe3000000 +#define CONFIG_SYS_PCIE2_IO_PHYS CONFIG_SYS_PCIE2_IO_BUS +#define CONFIG_SYS_PCIE2_IO_VIRT CONFIG_SYS_PCIE2_IO_BUS +#define CONFIG_SYS_PCIE2_IO_SIZE 0x1000000 /* 16M */ #if defined(CONFIG_PCI) @@ -406,10 +406,10 @@ * 0xa000_0000 512M PCI-Express 2 Memory * Changed it for operating from 0xd0000000 */ -#define CONFIG_SYS_DBAT1L ( CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW \ +#define CONFIG_SYS_DBAT1L ( CONFIG_SYS_PCIE1_MEM_PHYS | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCIE1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U /* @@ -449,10 +449,10 @@ * 0xe300_0000 16M PCI-Express 2 I/0 * Note that this is at 0xe0000000 */ -#define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW \ +#define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCIE1_IO_PHYS | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_32M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_32M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U /*