From: Tom Rini Date: Wed, 10 Feb 2021 02:42:53 +0000 (-0500) Subject: ppc: Remove MPC8610HPCD board X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=41bacbe142024c6bb26e7ca233d6e845ba1f56ac;p=u-boot.git ppc: Remove MPC8610HPCD board This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove this board. Cc: Priyanka Jain Signed-off-by: Tom Rini Reviewed-by: Priyanka Jain --- diff --git a/arch/powerpc/cpu/mpc86xx/Kconfig b/arch/powerpc/cpu/mpc86xx/Kconfig index 0f253051f2..294485794b 100644 --- a/arch/powerpc/cpu/mpc86xx/Kconfig +++ b/arch/powerpc/cpu/mpc86xx/Kconfig @@ -13,11 +13,6 @@ config TARGET_SBC8641D select ARCH_MPC8641 select BOARD_EARLY_INIT_F -config TARGET_MPC8610HPCD - bool "Support MPC8610HPCD" - select ARCH_MPC8610 - select BOARD_EARLY_INIT_F - config TARGET_MPC8641HPCN bool "Support MPC8641HPCN" select ARCH_MPC8641 @@ -62,7 +57,6 @@ config SYS_FSL_NUM_LAWS Number of local access windows. This is fixed per SoC. If not sure, do not change. -source "board/freescale/mpc8610hpcd/Kconfig" source "board/freescale/mpc8641hpcn/Kconfig" source "board/sbc8641d/Kconfig" source "board/xes/xpedite517x/Kconfig" diff --git a/board/freescale/common/pixis.h b/board/freescale/common/pixis.h index 7b1c973520..474ae56d44 100644 --- a/board/freescale/common/pixis.h +++ b/board/freescale/common/pixis.h @@ -45,36 +45,6 @@ typedef struct pixis { u8 res2[4]; } __attribute__ ((packed)) pixis_t; -#elif defined(CONFIG_TARGET_MPC8610HPCD) -typedef struct pixis { - u8 id; - u8 ver; /* also called arch */ - u8 pver; - u8 csr; - u8 rst; - u8 pwr; - u8 aux; - u8 spd; - u8 brdcfg0; - u8 brdcfg1; - u8 res[4]; - u8 led; - u8 serno; - u8 vctl; - u8 vstat; - u8 vcfgen0; - u8 vcfgen1; - u8 vcore0; - u8 res1; - u8 vboot; - u8 vspeed[2]; - u8 res2; - u8 sclk[3]; - u8 res3; - u8 watch; - u8 res4[33]; -} __attribute__ ((packed)) pixis_t; - #elif defined(CONFIG_TARGET_MPC8641HPCN) typedef struct pixis { u8 id; diff --git a/board/freescale/mpc8610hpcd/Kconfig b/board/freescale/mpc8610hpcd/Kconfig deleted file mode 100644 index 8f713beaa8..0000000000 --- a/board/freescale/mpc8610hpcd/Kconfig +++ /dev/null @@ -1,12 +0,0 @@ -if TARGET_MPC8610HPCD - -config SYS_BOARD - default "mpc8610hpcd" - -config SYS_VENDOR - default "freescale" - -config SYS_CONFIG_NAME - default "MPC8610HPCD" - -endif diff --git a/board/freescale/mpc8610hpcd/MAINTAINERS b/board/freescale/mpc8610hpcd/MAINTAINERS deleted file mode 100644 index 9b1e0cd4e5..0000000000 --- a/board/freescale/mpc8610hpcd/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -MPC8610HPCD BOARD -M: Priyanka Jain -S: Maintained -F: board/freescale/mpc8610hpcd/ -F: include/configs/MPC8610HPCD.h -F: configs/MPC8610HPCD_defconfig diff --git a/board/freescale/mpc8610hpcd/Makefile b/board/freescale/mpc8610hpcd/Makefile deleted file mode 100644 index 3a02a06416..0000000000 --- a/board/freescale/mpc8610hpcd/Makefile +++ /dev/null @@ -1,7 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# Copyright 2007 Freescale Semiconductor, Inc. - -obj-y += mpc8610hpcd.o -obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o -obj-y += law.o -obj-$(CONFIG_FSL_DIU_FB) += mpc8610hpcd_diu.o diff --git a/board/freescale/mpc8610hpcd/README b/board/freescale/mpc8610hpcd/README deleted file mode 100644 index 066e625d48..0000000000 --- a/board/freescale/mpc8610hpcd/README +++ /dev/null @@ -1,73 +0,0 @@ -Freescale MPC8610HPCD board -=========================== - - -Building U-Boot ---------------- - - $ make MPC8610HPCD_config - Configuring for MPC8610HPCD board... - - $ make - - -Flashing U-Boot ---------------- -The flash is 128M starting at 0xF800_0000. - -The alternate image is at 0xFBF0_0000 -The boot image is at 0xFFF0_0000. - - -To Flash U-Boot into the booting bank: - - tftp 1000000 u-boot.bin - protect off all - erase fff00000 +$filesize - cp.b 1000000 fff00000 $filesize - - -To Flash U-Boot into the alternate bank - - tftp 1000000 u-boot.bin - erase fbf00000 +$filesize - cp.b 1000000 fbf00000 $filesize - - -pixis_reset command -------------------- -A new command, "pixis_reset", is introduced to reset mpc8610hpcd board -using the FPGA sequencer. When the board restarts, it has the option -of using either the current or alternate flash bank as the boot -image, with or without the watchdog timer enabled, and finally with -or without frequency changes. - -Usage is; - - pixis_reset - pixis_reset altbank - pixis_reset altbank wd - pixis_reset altbank cf - pixis_reset cf - -Examples; - - /* reset to current bank, like "reset" command */ - pixis_reset - - /* reset board but use the to alternate flash bank */ - pixis_reset altbank - - /* reset board, use alternate flash bank with watchdog timer enabled*/ - pixis_reset altbank wd - - /* reset board to alternate bank with frequency changed. - * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio - */ - pixis-reset altbank cf 40 2.5 10 - - -DIP Switch Settings -------------------- -To manually switch the flash banks using the DIP switch -settings, toggle both SW6:1 and SW6:2. diff --git a/board/freescale/mpc8610hpcd/ddr.c b/board/freescale/mpc8610hpcd/ddr.c deleted file mode 100644 index c4d985347b..0000000000 --- a/board/freescale/mpc8610hpcd/ddr.c +++ /dev/null @@ -1,56 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright 2008 Freescale Semiconductor, Inc. - */ - -#include - -#include -#include - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - /* - * Factors to consider for clock adjust: - * - number of chips on bus - * - position of slot - * - DDR1 vs. DDR2? - * - ??? - * - * This needs to be determined on a board-by-board basis. - * 0110 3/4 cycle late - * 0111 7/8 cycle late - */ - popts->clk_adjust = 7; - - /* - * Factors to consider for CPO: - * - frequency - * - ddr1 vs. ddr2 - */ - popts->cpo_override = 10; - - /* - * Factors to consider for write data delay: - * - number of DIMMs - * - * 1 = 1/4 clock delay - * 2 = 1/2 clock delay - * 3 = 3/4 clock delay - * 4 = 1 clock delay - * 5 = 5/4 clock delay - * 6 = 3/2 clock delay - */ - popts->write_data_delay = 3; - - /* 2T timing enable */ - popts->twot_en = 1; - - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 0; -} diff --git a/board/freescale/mpc8610hpcd/law.c b/board/freescale/mpc8610hpcd/law.c deleted file mode 100644 index 7bf5e6815d..0000000000 --- a/board/freescale/mpc8610hpcd/law.c +++ /dev/null @@ -1,21 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2008,2010 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - */ - -#include -#include -#include - -struct law_entry law_table[] = { -#if !defined(CONFIG_SPD_EEPROM) - SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_DDR_1), -#endif - SET_LAW(PIXIS_BASE, LAW_SIZE_2M, LAW_TRGT_IF_LBC), - SET_LAW(CONFIG_SYS_FLASH_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC), -}; - -int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd.c b/board/freescale/mpc8610hpcd/mpc8610hpcd.c deleted file mode 100644 index 52bf4da98e..0000000000 --- a/board/freescale/mpc8610hpcd/mpc8610hpcd.c +++ /dev/null @@ -1,335 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2007,2009-2011 Freescale Semiconductor, Inc. - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -void sdram_init(void); -phys_size_t fixed_sdram(void); -int mpc8610hpcd_diu_init(void); - - -/* called before any console output */ -int board_early_init_f(void) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile ccsr_gur_t *gur = &immap->im_gur; - - gur->gpiocr |= 0x88aa5500; /* DIU16, IR1, UART0, UART2 */ - - return 0; -} - -int misc_init_r(void) -{ - u8 tmp_val, version; - u8 *pixis_base = (u8 *)PIXIS_BASE; - - /*Do not use 8259PIC*/ - tmp_val = in_8(pixis_base + PIXIS_BRDCFG0); - out_8(pixis_base + PIXIS_BRDCFG0, tmp_val | 0x80); - - /*For FPGA V7 or higher, set the IRQMAPSEL to 0 to use MAP0 interrupt*/ - version = in_8(pixis_base + PIXIS_PVER); - if(version >= 0x07) { - tmp_val = in_8(pixis_base + PIXIS_BRDCFG0); - out_8(pixis_base + PIXIS_BRDCFG0, tmp_val & 0xbf); - } - - /* Using this for DIU init before the driver in linux takes over - * Enable the TFP410 Encoder (I2C address 0x38) - */ - - tmp_val = 0xBF; - i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); - /* Verify if enabled */ - tmp_val = 0; - i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); - debug("DVI Encoder Read: 0x%02x\n", tmp_val); - - tmp_val = 0x10; - i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); - /* Verify if enabled */ - tmp_val = 0; - i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); - debug("DVI Encoder Read: 0x%02x\n", tmp_val); - - return 0; -} - -int checkboard(void) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile ccsr_local_mcm_t *mcm = &immap->im_local_mcm; - u8 *pixis_base = (u8 *)PIXIS_BASE; - - printf ("Board: MPC8610HPCD, Sys ID: 0x%02x, " - "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", - in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER), - in_8(pixis_base + PIXIS_PVER)); - - /* - * The MPC8610 HPCD workbook says that LBMAP=11 is the "normal" boot - * bank and LBMAP=00 is the alternate bank. However, the pixis - * altbank code can only set bits, not clear them, so we treat 00 as - * the normal bank and 11 as the alternate. - */ - switch (in_8(pixis_base + PIXIS_VBOOT) & 0xC0) { - case 0: - puts("vBank: Standard\n"); - break; - case 0x40: - puts("Promjet\n"); - break; - case 0x80: - puts("NAND\n"); - break; - case 0xC0: - puts("vBank: Alternate\n"); - break; - } - - mcm->abcr |= 0x00010000; /* 0 */ - mcm->hpmr3 = 0x80000008; /* 4c */ - mcm->hpmr0 = 0; - mcm->hpmr1 = 0; - mcm->hpmr2 = 0; - mcm->hpmr4 = 0; - mcm->hpmr5 = 0; - - return 0; -} - - -int dram_init(void) -{ - phys_size_t dram_size = 0; - -#if defined(CONFIG_SPD_EEPROM) - dram_size = fsl_ddr_sdram(); -#else - dram_size = fixed_sdram(); -#endif - - setup_ddr_bat(dram_size); - - debug(" DDR: "); - gd->ram_size = dram_size; - - return 0; -} - - -#if !defined(CONFIG_SPD_EEPROM) -/* - * Fixed sdram init -- doesn't use serial presence detect. - */ - -phys_size_t fixed_sdram(void) -{ -#if !defined(CONFIG_SYS_RAMBOOT) - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - struct ccsr_ddr __iomem *ddr = &immap->im_ddr1; - uint d_init; - - ddr->cs0_bnds = 0x0000001f; - ddr->cs0_config = 0x80010202; - - ddr->timing_cfg_3 = 0x00000000; - ddr->timing_cfg_0 = 0x00260802; - ddr->timing_cfg_1 = 0x3935d322; - ddr->timing_cfg_2 = 0x14904cc8; - ddr->sdram_mode = 0x00480432; - ddr->sdram_mode_2 = 0x00000000; - ddr->sdram_interval = 0x06180fff; /* 0x06180100; */ - ddr->sdram_data_init = 0xDEADBEEF; - ddr->sdram_clk_cntl = 0x03800000; - ddr->sdram_cfg_2 = 0x04400010; - -#if defined(CONFIG_DDR_ECC) - ddr->err_int_en = 0x0000000d; - ddr->err_disable = 0x00000000; - ddr->err_sbe = 0x00010000; -#endif - asm("sync;isync"); - - udelay(500); - - ddr->sdram_cfg = 0xc3000000; /* 0xe3008000;*/ - - -#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) - d_init = 1; - debug("DDR - 1st controller: memory initializing\n"); - /* - * Poll until memory is initialized. - * 512 Meg at 400 might hit this 200 times or so. - */ - while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) - udelay(1000); - - debug("DDR: memory initialized\n\n"); - asm("sync; isync"); - udelay(500); -#endif - - return 512 * 1024 * 1024; -#endif - return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; -} - -#endif - -#if defined(CONFIG_PCI) -/* - * Initialize PCI Devices, report devices found. - */ - -#ifndef CONFIG_PCI_PNP -static struct pci_config_table pci_fsl86xxads_config_table[] = { - {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, - PCI_IDSEL_NUMBER, PCI_ANY_ID, - pci_cfgfunc_config_device, {PCI_ENET0_IOADDR, - PCI_ENET0_MEMADDR, - PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER} }, - {} -}; -#endif - - -static struct pci_controller pci1_hose; -#endif /* CONFIG_PCI */ - -void pci_init_board(void) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR; - volatile ccsr_gur_t *gur = &immap->im_gur; - struct fsl_pci_info pci_info; - u32 devdisr; - int first_free_busno; - int pci_agent; - - devdisr = in_be32(&gur->devdisr); - - first_free_busno = fsl_pcie_init_board(0); - -#ifdef CONFIG_PCI1 - if (!(devdisr & MPC86xx_DEVDISR_PCI1)) { - SET_STD_PCI_INFO(pci_info, 1); - set_next_law(pci_info.mem_phys, - law_size_bits(pci_info.mem_size), pci_info.law); - set_next_law(pci_info.io_phys, - law_size_bits(pci_info.io_size), pci_info.law); - - pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs); - printf("PCI: connected to PCI slots as %s" \ - " (base address %lx)\n", - pci_agent ? "Agent" : "Host", - pci_info.regs); -#ifndef CONFIG_PCI_PNP - pci1_hose.config_table = pci_mpc86xxcts_config_table; -#endif - first_free_busno = fsl_pci_init_port(&pci_info, - &pci1_hose, first_free_busno); - } else { - printf("PCI: disabled\n"); - } - - puts("\n"); -#else - setbits_be32(&gur->devdisr, MPC86xx_DEVDISR_PCI1); /* disable */ -#endif - - fsl_pcie_init_board(first_free_busno); -} - -#if defined(CONFIG_OF_BOARD_SETUP) -int ft_board_setup(void *blob, struct bd_info *bd) -{ - ft_cpu_setup(blob, bd); - - FT_FSL_PCI_SETUP; - - return 0; -} -#endif - -/* - * get_board_sys_clk - * Reads the FPGA on board for CONFIG_SYS_CLK_FREQ - */ - -unsigned long -get_board_sys_clk(ulong dummy) -{ - u8 i; - ulong val = 0; - u8 *pixis_base = (u8 *)PIXIS_BASE; - - i = in_8(pixis_base + PIXIS_SPD); - i &= 0x07; - - switch (i) { - case 0: - val = 33333000; - break; - case 1: - val = 39999600; - break; - case 2: - val = 49999500; - break; - case 3: - val = 66666000; - break; - case 4: - val = 83332500; - break; - case 5: - val = 99999000; - break; - case 6: - val = 133332000; - break; - case 7: - val = 166665000; - break; - } - - return val; -} - -int board_eth_init(struct bd_info *bis) -{ - return pci_eth_init(bis); -} - -void board_reset(void) -{ - u8 *pixis_base = (u8 *)PIXIS_BASE; - - out_8(pixis_base + PIXIS_RST, 0); - - while (1) - ; -} diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c b/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c deleted file mode 100644 index 9b96d0d33f..0000000000 --- a/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c +++ /dev/null @@ -1,72 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2007-2011 Freescale Semiconductor, Inc. - * Authors: York Sun - * Timur Tabi - * - * FSL DIU Framebuffer driver - */ - -#include -#include -#include -#include -#include -#include -#include "../common/pixis.h" - -#define PX_BRDCFG0_DLINK 0x10 -#define PX_BRDCFG0_DVISEL 0x08 - -void diu_set_pixel_clock(unsigned int pixclock) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile ccsr_gur_t *gur = &immap->im_gur; - volatile unsigned int *guts_clkdvdr = &gur->clkdvdr; - unsigned long speed_ccb, temp, pixval; - - speed_ccb = get_bus_freq(0); - temp = 1000000000/pixclock; - temp *= 1000; - pixval = speed_ccb / temp; - debug("DIU pixval = %lu\n", pixval); - - /* Modify PXCLK in GUTS CLKDVDR */ - debug("DIU: Current value of CLKDVDR = 0x%08x\n", *guts_clkdvdr); - temp = *guts_clkdvdr & 0x2000FFFF; - *guts_clkdvdr = temp; /* turn off clock */ - *guts_clkdvdr = temp | 0x80000000 | ((pixval & 0x1F) << 16); - debug("DIU: Modified value of CLKDVDR = 0x%08x\n", *guts_clkdvdr); -} - -int platform_diu_init(unsigned int xres, unsigned int yres, const char *port) -{ - const char *name; - int gamma_fix = 0; - u32 pixel_format = 0x88883316; - u8 temp; - - temp = in_8(&pixis->brdcfg0); - - if (strncmp(port, "dlvds", 5) == 0) { - /* Dual link LVDS */ - gamma_fix = 1; - temp &= ~(PX_BRDCFG0_DLINK | PX_BRDCFG0_DVISEL); - name = "Dual-Link LVDS"; - } else if (strncmp(port, "lvds", 4) == 0) { - /* Single link LVDS */ - temp = (temp & ~PX_BRDCFG0_DVISEL) | PX_BRDCFG0_DLINK; - name = "Single-Link LVDS"; - } else { - /* DVI */ - if (in_8(&pixis->ver) == 1) /* Board version */ - pixel_format = 0x88882317; - temp |= PX_BRDCFG0_DVISEL; - name = "DVI"; - } - - printf("DIU: Switching to %s monitor @ %ux%u\n", name, xres, yres); - out_8(&pixis->brdcfg0, temp); - - return fsl_diu_init(xres, yres, pixel_format, gamma_fix); -} diff --git a/configs/MPC8610HPCD_defconfig b/configs/MPC8610HPCD_defconfig deleted file mode 100644 index b9ef566204..0000000000 --- a/configs/MPC8610HPCD_defconfig +++ /dev/null @@ -1,37 +0,0 @@ -CONFIG_PPC=y -CONFIG_SYS_TEXT_BASE=0xfff00000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_MPC86xx=y -CONFIG_HIGH_BATS=y -CONFIG_TARGET_MPC8610HPCD=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_BOOTDELAY=10 -# CONFIG_CONSOLE_MUX is not set -CONFIG_MISC_INIT_R=y -CONFIG_HUSH_PARSER=y -# CONFIG_AUTO_COMPLETE is not set -CONFIG_CMD_IMLS=y -CONFIG_CMD_I2C=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_BMP=y -CONFIG_CMD_EXT2=y -CONFIG_DOS_PARTITION=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_ADDR=0xFFF80000 -CONFIG_SCSI_AHCI=y -# CONFIG_MMC is not set -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SCSI=y -CONFIG_SYS_NS16550=y -CONFIG_USB=y -CONFIG_USB_KEYBOARD=y -CONFIG_VIDEO=y -CONFIG_OF_LIBFDT=y diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h deleted file mode 100644 index f444be0d86..0000000000 --- a/include/configs/MPC8610HPCD.h +++ /dev/null @@ -1,559 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0 */ -/* - * Copyright 2007-2011 Freescale Semiconductor, Inc. - */ - -/* - * MPC8610HPCD board configuration file - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include - -/* High Level Configuration Options */ -#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ - -/* video */ -#define CONFIG_FSL_DIU_FB - -#ifdef CONFIG_FSL_DIU_FB -#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x2c000) -#define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_BMP_LOGO -#endif - -#ifdef RUN_DIAG -#define CONFIG_SYS_DIAG_ADDR 0xff800000 -#endif - -/* - * virtual address to be used for temporary mappings. There - * should be 128k free at this VA. - */ -#define CONFIG_SYS_SCRATCH_VA 0xc0000000 - -#define CONFIG_PCI1 1 /* PCI controller 1 */ -#define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */ -#define CONFIG_PCIE2 1 /* PCIe 2 connected to slot */ -#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ -#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ - -#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ - -#define CONFIG_BAT_RW 1 /* Use common BAT rw code */ -#define CONFIG_ALTIVEC 1 - -/* - * L2CR setup -- make sure this is right for your board! - */ -#define CONFIG_SYS_L2 -#define L2_INIT 0 -#define L2_ENABLE (L2CR_L2E |0x00100000 ) - -#ifndef CONFIG_SYS_CLK_FREQ -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) -#endif - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ -#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ - -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR -#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 -#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW - -/* DDR Setup */ -#define CONFIG_SPD_EEPROM /* Use SPD for DDR */ -#define CONFIG_DDR_SPD - -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ -#define CONFIG_VERY_BIG_RAM - -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) - -#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ - -/* These are used when DDR doesn't use SPD. */ -#define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ - -#if 0 /* TODO */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */ -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_TIMING_0 0x00260802 -#define CONFIG_SYS_DDR_TIMING_1 0x3935d322 -#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 -#define CONFIG_SYS_DDR_MODE_1 0x00480432 -#define CONFIG_SYS_DDR_MODE_2 0x00000000 -#define CONFIG_SYS_DDR_INTERVAL 0x06180100 -#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef -#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 -#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 -#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 -#define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ -#define CONFIG_SYS_DDR_CONTROL2 0x04400010 - -#define CONFIG_SYS_DDR_ERR_INT_EN 0x00000000 -#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 -#define CONFIG_SYS_DDR_SBE 0x000f0000 - -#endif - -#define CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_NXID -#define CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -#define CONFIG_SYS_FLASH_BASE 0xf0000000 /* start of FLASH 128M */ -#define CONFIG_SYS_FLASH_BASE2 0xf8000000 - -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} - -#define CONFIG_SYS_BR0_PRELIM 0xf8001001 /* port size 16bit */ -#define CONFIG_SYS_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/ - -#define CONFIG_SYS_BR1_PRELIM 0xf0001001 /* port size 16bit */ -#define CONFIG_SYS_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */ -#if 0 /* TODO */ -#define CONFIG_SYS_BR2_PRELIM 0xf0000000 -#define CONFIG_SYS_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */ -#endif -#define CONFIG_SYS_BR3_PRELIM 0xe8000801 /* port size 8bit */ -#define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ - -#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ -#define PIXIS_BASE 0xe8000000 /* PIXIS registers */ -#define PIXIS_ID 0x0 /* Board ID at offset 0 */ -#define PIXIS_VER 0x1 /* Board version at offset 1 */ -#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ -#define PIXIS_RST 0x4 /* PIXIS Reset Control register */ -#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch */ -#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ -#define PIXIS_BRDCFG0 0x8 /* PIXIS Board Configuration Register0*/ -#define PIXIS_VCTL 0x10 /* VELA Control Register */ -#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ -#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ -#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ -#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ -#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ -#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ -#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ -#define CONFIG_SYS_PIXIS_VBOOT_MASK 0xC0 /* Reset altbank mask */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#if defined(CONFIG_SYS_RAMBOOT) -#undef CONFIG_SPD_EEPROM -#define CONFIG_SYS_SDRAM_SIZE 256 -#endif - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#ifndef CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ -#else -#define CONFIG_SYS_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */ -#endif -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */ - -/* Serial Port */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* maximum size of the flat tree (8K) */ -#define OF_FLAT_TREE_MAX_SIZE 8192 - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS -#define CONFIG_SYS_PCI1_MEM_VIRT CONFIG_SYS_PCI1_MEM_BUS -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BUS 0x0000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000 -#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ - -/* controller 1, Base address 0xa000 */ -#define CONFIG_SYS_PCIE1_NAME "ULI" -#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */ - -/* controller 2, Base Address 0x9000 */ -#define CONFIG_SYS_PCIE2_NAME "Slot 1" -#define CONFIG_SYS_PCIE2_MEM_BUS 0x90000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 /* reuse mem LAW */ -#define CONFIG_SYS_PCIE2_IO_PHYS 0xe2000000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00100000 /* 1M */ - -#if defined(CONFIG_PCI) - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - -#define CONFIG_ULI526X - -/************************************************************ - * USB support - ************************************************************/ -#define CONFIG_PCI_OHCI 1 -#define CONFIG_USB_OHCI_NEW 1 -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 -#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 - -#if !defined(CONFIG_PCI_PNP) -#define PCI_ENET0_IOADDR 0xe0000000 -#define PCI_ENET0_MEMADDR 0xe0000000 -#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ -#endif - -#ifdef CONFIG_SCSI_AHCI -#define CONFIG_SATA_ULI5288 -#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 -#define CONFIG_SYS_SCSI_MAX_LUN 1 -#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) -#endif - -#endif /* CONFIG_PCI */ - -/* - * BAT0 2G Cacheable, non-guarded - * 0x0000_0000 2G DDR - */ -#define CONFIG_SYS_DBAT0L (BATL_PP_RW) -#define CONFIG_SYS_IBAT0L (BATL_PP_RW) - -/* - * BAT1 1G Cache-inhibited, guarded - * 0x8000_0000 256M PCI-1 Memory - * 0xa000_0000 256M PCI-Express 1 Memory - * 0x9000_0000 256M PCI-Express 2 Memory - */ - -#define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U - -/* - * BAT2 16M Cache-inhibited, guarded - * 0xe100_0000 1M PCI-1 I/O - */ - -#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_16M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U - -/* - * BAT3 4M Cache-inhibited, guarded - * 0xe000_0000 4M CCSR - */ - -#define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U - -#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) -#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ - | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ - | BATU_BL_1M | BATU_VS | BATU_VP) -#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ - | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU -#endif - -/* - * BAT4 32M Cache-inhibited, guarded - * 0xe200_0000 1M PCI-Express 2 I/O - * 0xe300_0000 1M PCI-Express 1 I/O - */ - -#define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U - -/* - * BAT5 128K Cacheable, non-guarded - * 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory) - */ -#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L -#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U - -/* - * BAT6 256M Cache-inhibited, guarded - * 0xf000_0000 256M FLASH - */ -#define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U - -/* Map the last 1M of flash where we're running from reset */ -#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ - | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY - -/* - * BAT7 4M Cache-inhibited, guarded - * 0xe800_0000 4M PIXIS - */ -#define CONFIG_SYS_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP) -#define CONFIG_SYS_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U - -/* - * Environment - */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -#define CONFIG_WATCHDOG /* watchdog enabled */ -#define CONFIG_SYS_WATCHDOG_FREQ 5000 /* Feed interval, 5s */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (256 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_IPADDR 192.168.1.100 - -#define CONFIG_HOSTNAME "unknown" -#define CONFIG_ROOTPATH "/opt/nfsroot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_UBOOTPATH 8610hpcd/u-boot.bin - -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_GATEWAYIP 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 - -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 0x10000000 - -#if defined(CONFIG_PCI1) -#define PCI_ENV \ - "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \ - "echo e;md ${a}e00 9\0" \ - "pci1regs=setenv a e0008; run pcireg\0" \ - "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \ - "pci d.w $b.0 56 1\0" \ - "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \ - "pci w.w $b.0 56 ffff\0" \ - "pci1err=setenv a e0008; run pcierr\0" \ - "pci1errc=setenv a e0008; run pcierrc\0" -#else -#define PCI_ENV "" -#endif - -#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) -#define PCIE_ENV \ - "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \ - "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \ - "pcie1regs=setenv a e000a; run pciereg\0" \ - "pcie2regs=setenv a e0009; run pciereg\0" \ - "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\ - "pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \ - "pci d $b.0 130 1\0" \ - "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\ - "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \ - "pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \ - "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \ - "pcie1err=setenv a e000a; run pcieerr\0" \ - "pcie2err=setenv a e0009; run pcieerr\0" \ - "pcie1errc=setenv a e000a; run pcieerrc\0" \ - "pcie2errc=setenv a e0009; run pcieerrc\0" -#else -#define PCIE_ENV "" -#endif - -#define DMA_ENV \ - "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\ - "mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \ - "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\ - "mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \ - "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\ - "mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \ - "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\ - "mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0" - -#ifdef ENV_DEBUG -#define CONFIG_EXTRA_ENV_SETTINGS \ -"netdev=eth0\0" \ -"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ -"tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize\0" \ -"consoledev=ttyS0\0" \ -"ramdiskaddr=0x18000000\0" \ -"ramdiskfile=8610hpcd/ramdisk.uboot\0" \ -"fdtaddr=0x17c00000\0" \ -"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \ -"bdev=sda3\0" \ -"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ -"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ -"maxcpus=1" \ -"eoi=mw e00400b0 0\0" \ -"iack=md e00400a0 1\0" \ -"ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \ - "md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \ - "md ${a}f00 5\0" \ -"ddr1regs=setenv a e0002; run ddrreg\0" \ -"gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \ - "md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \ - "md ${a}e60 1; md ${a}ef0 1d\0" \ -"guregs=setenv a e00e0; run gureg\0" \ -"mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \ -"mcmregs=setenv a e0001; run mcmreg\0" \ -"diuregs=md e002c000 1d\0" \ -"dium=mw e002c01c\0" \ -"diuerr=md e002c014 1\0" \ -"pmregs=md e00e1000 2b\0" \ -"lawregs=md e0000c08 4b\0" \ -"lbcregs=md e0005000 36\0" \ -"dma0regs=md e0021100 12\0" \ -"dma1regs=md e0021180 12\0" \ -"dma2regs=md e0021200 12\0" \ -"dma3regs=md e0021280 12\0" \ - PCI_ENV \ - PCIE_ENV \ - DMA_ENV -#else -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=0x18000000\0" \ - "ramdiskfile=8610hpcd/ramdisk.uboot\0" \ - "fdtaddr=0x17c00000\0" \ - "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \ - "bdev=sda3\0" -#endif - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#endif /* __CONFIG_H */