From: Roger Quadros Date: Wed, 6 Nov 2019 14:21:18 +0000 (+0200) Subject: phy: ti-pipe3: Fix SATA & USB PHY power up sequence X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=305a5d840eb900af9f8682e5dc57e96c2b457e64;p=u-boot.git phy: ti-pipe3: Fix SATA & USB PHY power up sequence As per "Table 26-7. SATA PHY Subsystem Low-Level Programming Sequence" in TRM [1] we need to turn on SATA_PHY_TX before SATA_PHY_RX. [1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf Signed-off-by: Roger Quadros --- diff --git a/drivers/phy/ti-pipe3-phy.c b/drivers/phy/ti-pipe3-phy.c index b9c8591470..0c59552bb8 100644 --- a/drivers/phy/ti-pipe3-phy.c +++ b/drivers/phy/ti-pipe3-phy.c @@ -41,14 +41,14 @@ #define SATA_PLL_SOFT_RESET (1<<18) /* PHY POWER CONTROL Register */ -#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000 -#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 0xE +#define PIPE3_PHY_PWRCTL_CLK_CMD_MASK GENMASK(21, 14) +#define PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 14 -#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK 0xFFC00000 -#define OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT 0x16 +#define PIPE3_PHY_PWRCTL_CLK_FREQ_MASK GENMASK(31, 22) +#define PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT 22 -#define OMAP_CTRL_PIPE3_PHY_TX_RX_POWERON 0x3 -#define OMAP_CTRL_PIPE3_PHY_TX_RX_POWEROFF 0x0 +#define PIPE3_PHY_RX_POWERON (0x1 << PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT) +#define PIPE3_PHY_TX_POWERON (0x2 << PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT) /* PHY RX Registers */ #define PIPE3_PHY_RX_ANA_PROGRAMMABILITY 0x0000000C @@ -264,19 +264,21 @@ static void omap_control_pipe3_power(struct omap_pipe3 *pipe3, int on) rate = rate/1000000; if (on) { - val &= ~(OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK | - OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK); - val |= OMAP_CTRL_PIPE3_PHY_TX_RX_POWERON << - OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT; - val |= rate << - OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT; + val &= ~(PIPE3_PHY_PWRCTL_CLK_CMD_MASK | + PIPE3_PHY_PWRCTL_CLK_FREQ_MASK); + val |= rate << PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT; + writel(val, pipe3->power_reg); + + /* Power up TX before RX for SATA & USB */ + val |= PIPE3_PHY_TX_POWERON; + writel(val, pipe3->power_reg); + + val |= PIPE3_PHY_RX_POWERON; + writel(val, pipe3->power_reg); } else { - val &= ~OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK; - val |= OMAP_CTRL_PIPE3_PHY_TX_RX_POWEROFF << - OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT; + val &= ~PIPE3_PHY_PWRCTL_CLK_CMD_MASK; + writel(val, pipe3->power_reg); } - - writel(val, pipe3->power_reg); } static void ti_pipe3_calibrate(struct omap_pipe3 *phy)