From: Lukasz Majewski <lukma@denx.de>
Date: Tue, 3 Sep 2019 14:38:46 +0000 (+0200)
Subject: ARM: display5: Remove common.c file (after DM/DTS U-Boot proper conversion)
X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=21c7d34279a4f4247e1f20492b87828187a090df;p=u-boot.git

ARM: display5: Remove common.c file (after DM/DTS U-Boot proper conversion)

The common.c file content can be safely moved to spl.c file after
performing the DM/DTS conversion for the U-Boot proper.

It contains the non DM/DTS setup code, which now is only used by SPL.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
---

diff --git a/board/liebherr/display5/Makefile b/board/liebherr/display5/Makefile
index f934672428..ee503add75 100644
--- a/board/liebherr/display5/Makefile
+++ b/board/liebherr/display5/Makefile
@@ -5,7 +5,7 @@
 # SPDX-License-Identifier:    GPL-2.0+
 #
 ifdef CONFIG_SPL_BUILD
-obj-y = common.o spl.o
+obj-y = spl.o
 else
-obj-y := common.o display5.o
+obj-y := display5.o
 endif
diff --git a/board/liebherr/display5/common.c b/board/liebherr/display5/common.c
deleted file mode 100644
index 5e714076a4..0000000000
--- a/board/liebherr/display5/common.c
+++ /dev/null
@@ -1,83 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2017 DENX Software Engineering
- * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
- */
-
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/arch/mx6-pins.h>
-#include "common.h"
-
-iomux_v3_cfg_t const uart_console_pads[] = {
-	/* UART5 */
-	MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX6_PAD_CSI0_DAT15__UART5_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX6_PAD_CSI0_DAT18__UART5_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX6_PAD_CSI0_DAT19__UART5_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-void displ5_set_iomux_uart_spl(void)
-{
-	SETUP_IOMUX_PADS(uart_console_pads);
-}
-
-iomux_v3_cfg_t const misc_pads_spl[] = {
-	/* Emergency recovery pin */
-	MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-void displ5_set_iomux_misc_spl(void)
-{
-	SETUP_IOMUX_PADS(misc_pads_spl);
-}
-
-#ifdef CONFIG_MXC_SPI
-iomux_v3_cfg_t const ecspi2_pads[] = {
-	/* SPI2, NOR Flash nWP, CS0 */
-	MX6_PAD_CSI0_DAT10__ECSPI2_MISO	| MUX_PAD_CTRL(SPI_PAD_CTRL),
-	MX6_PAD_CSI0_DAT9__ECSPI2_MOSI	| MUX_PAD_CTRL(SPI_PAD_CTRL),
-	MX6_PAD_CSI0_DAT8__ECSPI2_SCLK	| MUX_PAD_CTRL(SPI_PAD_CTRL),
-	MX6_PAD_CSI0_DAT11__GPIO5_IO29	| MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_SD3_DAT5__GPIO7_IO00	| MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-int board_spi_cs_gpio(unsigned int bus, unsigned int cs)
-{
-	if (bus != 1 || cs != 0)
-		return -EINVAL;
-
-	return IMX_GPIO_NR(5, 29);
-}
-
-void displ5_set_iomux_ecspi_spl(void)
-{
-	SETUP_IOMUX_PADS(ecspi2_pads);
-}
-
-#else
-void displ5_set_iomux_ecspi_spl(void) {}
-#endif
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-iomux_v3_cfg_t const usdhc4_pads[] = {
-	MX6_PAD_SD4_CLK__SD4_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_CMD__SD4_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT0__SD4_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT1__SD4_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT2__SD4_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT3__SD4_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT4__SD4_DATA4	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT5__SD4_DATA5	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT6__SD4_DATA6	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT7__SD4_DATA7	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_NANDF_ALE__SD4_RESET	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-
-void displ5_set_iomux_usdhc_spl(void)
-{
-	SETUP_IOMUX_PADS(usdhc4_pads);
-}
-
-#else
-void displ5_set_iomux_usdhc_spl(void) {}
-#endif
diff --git a/board/liebherr/display5/common.h b/board/liebherr/display5/common.h
index 4eb70dc42f..44c7470074 100644
--- a/board/liebherr/display5/common.h
+++ b/board/liebherr/display5/common.h
@@ -31,9 +31,4 @@
 #define ENET_PAD_CTRL_CLK  ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
 	PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
 
-void displ5_set_iomux_uart_spl(void);
-void displ5_set_iomux_ecspi_spl(void);
-void displ5_set_iomux_usdhc_spl(void);
-void displ5_set_iomux_misc_spl(void);
-
 #endif /* __DISPL5_COMMON_H_ */
diff --git a/board/liebherr/display5/spl.c b/board/liebherr/display5/spl.c
index 354b63e431..311edaf939 100644
--- a/board/liebherr/display5/spl.c
+++ b/board/liebherr/display5/spl.c
@@ -104,6 +104,80 @@ static const struct mx6_ddr3_cfg mt41k128m16jt_125 = {
 	.trasmin = 3500,
 };
 
+iomux_v3_cfg_t const uart_console_pads[] = {
+	/* UART5 */
+	MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT15__UART5_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT18__UART5_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT19__UART5_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+void displ5_set_iomux_uart_spl(void)
+{
+	SETUP_IOMUX_PADS(uart_console_pads);
+}
+
+iomux_v3_cfg_t const misc_pads_spl[] = {
+	/* Emergency recovery pin */
+	MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+void displ5_set_iomux_misc_spl(void)
+{
+	SETUP_IOMUX_PADS(misc_pads_spl);
+}
+
+#ifdef CONFIG_MXC_SPI
+iomux_v3_cfg_t const ecspi2_pads[] = {
+	/* SPI2, NOR Flash nWP, CS0 */
+	MX6_PAD_CSI0_DAT10__ECSPI2_MISO	| MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_CSI0_DAT9__ECSPI2_MOSI	| MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_CSI0_DAT8__ECSPI2_SCLK	| MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_CSI0_DAT11__GPIO5_IO29	| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD3_DAT5__GPIO7_IO00	| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int board_spi_cs_gpio(unsigned int bus, unsigned int cs)
+{
+	if (bus != 1 || cs != 0)
+		return -EINVAL;
+
+	return IMX_GPIO_NR(5, 29);
+}
+
+void displ5_set_iomux_ecspi_spl(void)
+{
+	SETUP_IOMUX_PADS(ecspi2_pads);
+}
+
+#else
+void displ5_set_iomux_ecspi_spl(void) {}
+#endif
+
+#ifdef CONFIG_FSL_ESDHC_IMX
+iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6_PAD_SD4_CLK__SD4_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_CMD__SD4_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT0__SD4_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT1__SD4_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT2__SD4_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT3__SD4_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT4__SD4_DATA4	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT5__SD4_DATA5	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT6__SD4_DATA6	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT7__SD4_DATA7	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NANDF_ALE__SD4_RESET	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+void displ5_set_iomux_usdhc_spl(void)
+{
+	SETUP_IOMUX_PADS(usdhc4_pads);
+}
+
+#else
+void displ5_set_iomux_usdhc_spl(void) {}
+#endif
+
 static void ccgr_init(void)
 {
 	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;