From: Piotr Wilczek Date: Fri, 7 Mar 2014 13:59:49 +0000 (+0100) Subject: board:trats2: Enable device tree on Trats2 X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=1ecab0f30f9051821fdb5ec1c689b7c531b4feda;p=u-boot.git board:trats2: Enable device tree on Trats2 This patch enables to run Trats2 board on device tree. Signed-off-by: Piotr Wilczek Signed-off-by: Kyungmin Park Signed-off-by: Minkyu Kang --- diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index a853ec659d..631a9bede1 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -1,6 +1,7 @@ dtb-$(CONFIG_EXYNOS4) += exynos4210-origen.dtb \ exynos4210-universal_c210.dtb \ - exynos4210-trats.dtb + exynos4210-trats.dtb \ + exynos4412-trats2.dtb dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \ exynos5250-snow.dtb \ diff --git a/arch/arm/dts/exynos4412-trats2.dts b/arch/arm/dts/exynos4412-trats2.dts new file mode 100644 index 0000000000..7d32067fdd --- /dev/null +++ b/arch/arm/dts/exynos4412-trats2.dts @@ -0,0 +1,434 @@ +/* + * Samsung's Exynos4412 based Trats2 board device tree source + * + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/dts-v1/; +/include/ "exynos4.dtsi" + +/ { + model = "Samsung Trats2 based on Exynos4412"; + compatible = "samsung,trats2", "samsung,exynos4412"; + + config { + samsung,dsim-device-name = "s6e8ax0"; + }; + + aliases { + i2c0 = "/i2c@13860000"; + i2c1 = "/i2c@13870000"; + i2c2 = "/i2c@13880000"; + i2c3 = "/i2c@13890000"; + i2c4 = "/i2c@138a0000"; + i2c5 = "/i2c@138b0000"; + i2c6 = "/i2c@138c0000"; + i2c7 = "/i2c@138d0000"; + serial0 = "/serial@13800000"; + console = "/serial@13820000"; + mmc0 = "sdhci@12510000"; + mmc2 = "sdhci@12530000"; + }; + + i2c@138d0000 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + status = "okay"; + + max77686_pmic@09 { + compatible = "maxim,max77686_pmic"; + interrupts = <7 0>; + reg = <0x09 0 0>; + #clock-cells = <1>; + + voltage-regulators { + ldo1_reg: ldo1 { + regulator-compatible = "LDO1"; + regulator-name = "VALIVE_1.0V_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-mem-on; + }; + + ldo2_reg: ldo2 { + regulator-compatible = "LDO2"; + regulator-name = "VM1M2_1.2V_AP"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-mem-on; + }; + + ldo3_reg: ldo3 { + regulator-compatible = "LDO3"; + regulator-name = "VCC_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-mem-on; + }; + + ldo4_reg: ldo4 { + regulator-compatible = "LDO4"; + regulator-name = "VCC_2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-mem-on; + }; + + ldo5_reg: ldo5 { + regulator-compatible = "LDO5"; + regulator-name = "VCC_1.8V_IO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-mem-on; + }; + + ldo6_reg: ldo6 { + regulator-compatible = "LDO6"; + regulator-name = "VMPLL_1.0V_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-mem-on; + }; + + ldo7_reg: ldo7 { + regulator-compatible = "LDO7"; + regulator-name = "VPLL_1.0V_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-mem-on; + }; + + ldo8_reg: ldo8 { + regulator-compatible = "LDO8"; + regulator-name = "VMIPI_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-mem-off; + }; + + ldo9_reg: ldo9 { + regulator-compatible = "LDO9"; + regulator-name = "CAM_ISP_MIPI_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-mem-idle; + }; + + ldo10_reg: ldo10 { + regulator-compatible = "LDO10"; + regulator-name = "VMIPI_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-mem-off; + }; + + ldo11_reg: ldo11 { + regulator-compatible = "LDO11"; + regulator-name = "VABB1_1.95V"; + regulator-min-microvolt = <1950000>; + regulator-max-microvolt = <1950000>; + regulator-always-on; + regulator-mem-off; + }; + + ldo12_reg: ldo12 { + regulator-compatible = "LDO12"; + regulator-name = "VUOTG_3.0V"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-mem-off; + }; + + ldo13_reg: ldo13 { + regulator-compatible = "LDO13"; + regulator-name = "NFC_AVDD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-mem-idle; + }; + + ldo14_reg: ldo14 { + regulator-compatible = "LDO14"; + regulator-name = "VABB2_1.95V"; + regulator-min-microvolt = <1950000>; + regulator-max-microvolt = <1950000>; + regulator-always-on; + regulator-mem-off; + }; + + ldo15_reg: ldo15 { + regulator-compatible = "LDO15"; + regulator-name = "VHSIC_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-mem-off; + }; + + ldo16_reg: ldo16 { + regulator-compatible = "LDO16"; + regulator-name = "VHSIC_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-mem-off; + }; + + ldo17_reg: ldo17 { + regulator-compatible = "LDO17"; + regulator-name = "CAM_SENSOR_CORE_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-mem-idle; + }; + + ldo18_reg: ldo18 { + regulator-compatible = "LDO18"; + regulator-name = "CAM_ISP_SEN_IO_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-mem-idle; + }; + + ldo19_reg: ldo19 { + regulator-compatible = "LDO19"; + regulator-name = "VT_CAM_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-mem-idle; + }; + + ldo20_reg: ldo20 { + regulator-compatible = "LDO20"; + regulator-name = "VDDQ_PRE_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-mem-idle; + }; + + ldo21_reg: ldo21 { + regulator-compatible = "LDO21"; + regulator-name = "VTF_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-mem-idle; + }; + + ldo22_reg: ldo22 { + regulator-compatible = "LDO22"; + regulator-name = "VMEM_VDD_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-mem-off; + }; + + ldo23_reg: ldo23 { + regulator-compatible = "LDO23"; + regulator-name = "TSP_AVDD_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-mem-idle; + }; + + ldo24_reg: ldo24 { + regulator-compatible = "LDO24"; + regulator-name = "TSP_VDD_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-mem-idle; + }; + + ldo25_reg: ldo25 { + regulator-compatible = "LDO25"; + regulator-name = "LCD_VCC_3.3V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-mem-idle; + }; + + ldo26_reg: ldo26 { + regulator-compatible = "LDO26"; + regulator-name = "MOTOR_VCC_3.0V"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-mem-idle; + }; + + buck1_reg: buck1 { + regulator-compatible = "BUCK1"; + regulator-name = "vdd_mif"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + regulator-mem-off; + }; + + buck2_reg: buck2 { + regulator-compatible = "BUCK2"; + regulator-name = "vdd_arm"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + regulator-mem-off; + }; + + buck3_reg: buck3 { + regulator-compatible = "BUCK3"; + regulator-name = "vdd_int"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1150000>; + regulator-always-on; + regulator-boot-on; + regulator-mem-off; + }; + + buck4_reg: buck4 { + regulator-compatible = "BUCK4"; + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-mem-off; + }; + + buck5_reg: buck5 { + regulator-compatible = "BUCK5"; + regulator-name = "VMEM_1.2V_AP"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + buck6_reg: buck6 { + regulator-compatible = "BUCK6"; + regulator-name = "VCC_SUB_1.35V"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + buck7_reg: buck7 { + regulator-compatible = "BUCK7"; + regulator-name = "VCC_SUB_2.0V"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + buck8_reg: buck8 { + regulator-compatible = "BUCK8"; + regulator-name = "VMEM_VDDF_3.0V"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + regulator-mem-off; + }; + + buck9_reg: buck9 { + regulator-compatible = "BUCK9"; + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1200000>; + regulator-mem-off; + }; + }; + }; + }; + + fimd@11c00000 { + compatible = "samsung,exynos-fimd"; + reg = <0x11c00000 0xa4>; + + samsung,vl-freq = <60>; + samsung,vl-col = <720>; + samsung,vl-row = <1280>; + samsung,vl-width = <720>; + samsung,vl-height = <1280>; + + samsung,vl-clkp = <0>; + samsung,vl-oep = <0>; + samsung,vl-hsp = <1>; + samsung,vl-vsp = <1>; + samsung,vl-dp = <1>; + samsung,vl-bpix = <4>; + + samsung,vl-hspw = <5>; + samsung,vl-hbpd = <10>; + samsung,vl-hfpd = <10>; + samsung,vl-vspw = <2>; + samsung,vl-vbpd = <1>; + samsung,vl-vfpd = <13>; + samsung,vl-cmd-allow-len = <0xf>; + + samsung,winid = <0>; + samsung,power-on-delay = <30>; + samsung,interface-mode = <1>; + samsung,mipi-enabled = <1>; + samsung,dp-enabled; + samsung,dual-lcd-enabled; + + samsung,logo-on = <1>; + samsung,resolution = <0>; + samsung,rgb-mode = <0>; + }; + + mipidsi@11c80000 { + compatible = "samsung,exynos-mipi-dsi"; + reg = <0x11c80000 0x5c>; + + samsung,dsim-config-e-interface = <1>; + samsung,dsim-config-e-virtual-ch = <0>; + samsung,dsim-config-e-pixel-format = <7>; + samsung,dsim-config-e-burst-mode = <1>; + samsung,dsim-config-e-no-data-lane = <3>; + samsung,dsim-config-e-byte-clk = <0>; + samsung,dsim-config-hfp = <1>; + + samsung,dsim-config-p = <3>; + samsung,dsim-config-m = <120>; + samsung,dsim-config-s = <1>; + + samsung,dsim-config-pll-stable-time = <500>; + samsung,dsim-config-esc-clk = <20000000>; + samsung,dsim-config-stop-holding-cnt = <0x7ff>; + samsung,dsim-config-bta-timeout = <0xff>; + samsung,dsim-config-rx-timeout = <0xffff>; + + samsung,dsim-device-id = <0xffffffff>; + samsung,dsim-device-bus-id = <0>; + + samsung,dsim-device-reverse-panel = <1>; + }; + + sdhci@12510000 { + samsung,bus-width = <8>; + samsung,timing = <1 3 3>; + pwr-gpios = <&gpio 0x2004002 0>; + }; + + sdhci@12520000 { + status = "disabled"; + }; + + sdhci@12530000 { + samsung,bus-width = <4>; + samsung,timing = <1 2 3>; + cd-gpios = <&gpio 0x20C6004 0>; + }; + + sdhci@12540000 { + status = "disabled"; + }; +}; diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c index c17c24d60a..2a6c9f9170 100644 --- a/board/samsung/trats2/trats2.c +++ b/board/samsung/trats2/trats2.c @@ -8,15 +8,9 @@ #include #include -#include -#include -#include -#include -#include -#include -#include #include #include +#include #include #include #include @@ -28,7 +22,6 @@ #include #include #include -#include DECLARE_GLOBAL_DATA_PTR; @@ -69,16 +62,6 @@ static void check_hw_revision(void) board_rev = modelrev << 8; } -#ifdef CONFIG_DISPLAY_BOARDINFO -int checkboard(void) -{ - puts("Board:\tTRATS2\n"); - printf("HW Revision:\t0x%04x\n", board_rev); - - return 0; -} -#endif - u32 get_board_rev(void) { return board_rev; @@ -156,33 +139,24 @@ int get_soft_i2c_sda_pin(void) } #endif -int board_early_init_f(void) +int exynos_early_init_f(void) { - check_hw_revision(); board_external_gpio_init(); - gd->flags |= GD_FLG_DISABLE_CONSOLE; - return 0; } static int pmic_init_max77686(void); -int board_init(void) +int exynos_init(void) { - struct exynos4_power *pwr = - (struct exynos4_power *)samsung_get_base_power(); - - gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; - - /* workaround: clear INFORM4..5 */ - writel(0, (unsigned int)&pwr->inform4); - writel(0, (unsigned int)&pwr->inform5); + check_hw_revision(); + printf("HW Revision:\t0x%04x\n", board_rev); return 0; } -int power_init_board(void) +int exynos_power_init(void) { int chrg; struct power_battery *pb; @@ -248,90 +222,6 @@ int power_init_board(void) return 0; } -int dram_init(void) -{ - u32 size_mb; - - size_mb = (get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) + - get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) + - get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) + - get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE)) >> 20; - - gd->ram_size = size_mb << 20; - - return 0; -} - -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; - gd->bd->bi_dram[1].start = PHYS_SDRAM_2; - gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE; - gd->bd->bi_dram[2].start = PHYS_SDRAM_3; - gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE; - gd->bd->bi_dram[3].start = PHYS_SDRAM_4; - gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE; -} - -int board_mmc_init(bd_t *bis) -{ - int err0, err2 = 0; - - gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2(); - - /* eMMC_EN: SD_0_CDn: GPK0[2] Output High */ - s5p_gpio_direction_output(&gpio2->k0, 2, 1); - s5p_gpio_set_pull(&gpio2->k0, 2, GPIO_PULL_NONE); - - /* - * eMMC GPIO: - * SDR 8-bit@48MHz at MMC0 - * GPK0[0] SD_0_CLK(2) - * GPK0[1] SD_0_CMD(2) - * GPK0[2] SD_0_CDn -> Not used - * GPK0[3:6] SD_0_DATA[0:3](2) - * GPK1[3:6] SD_0_DATA[0:3](3) - * - * DDR 4-bit@26MHz at MMC4 - * GPK0[0] SD_4_CLK(3) - * GPK0[1] SD_4_CMD(3) - * GPK0[2] SD_4_CDn -> Not used - * GPK0[3:6] SD_4_DATA[0:3](3) - * GPK1[3:6] SD_4_DATA[4:7](4) - */ - - err0 = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); - - /* - * MMC device init - * mmc0 : eMMC (8-bit buswidth) - * mmc2 : SD card (4-bit buswidth) - */ - if (err0) - debug("SDMMC0 not configured\n"); - else - err0 = s5p_mmc_init(0, 8); - - /* T-flash detect */ - s5p_gpio_cfg_pin(&gpio2->x3, 4, 0xf); - s5p_gpio_set_pull(&gpio2->x3, 4, GPIO_PULL_UP); - - /* - * Check the T-flash detect pin - * GPX3[4] T-flash detect pin - */ - if (!s5p_gpio_get_value(&gpio2->x3, 4)) { - err2 = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); - if (err2) - debug("SDMMC2 not configured\n"); - else - err2 = s5p_mmc_init(2, 4); - } - - return err0 & err2; -} - #ifdef CONFIG_USB_GADGET static int s5pc210_phy_control(int on) { @@ -479,46 +369,7 @@ static int pmic_init_max77686(void) */ #ifdef CONFIG_LCD -static struct mipi_dsim_config dsim_config = { - .e_interface = DSIM_VIDEO, - .e_virtual_ch = DSIM_VIRTUAL_CH_0, - .e_pixel_format = DSIM_24BPP_888, - .e_burst_mode = DSIM_BURST_SYNC_EVENT, - .e_no_data_lane = DSIM_DATA_LANE_4, - .e_byte_clk = DSIM_PLL_OUT_DIV8, - .hfp = 1, - - .p = 3, - .m = 120, - .s = 1, - - /* D-PHY PLL stable time spec :min = 200usec ~ max 400usec */ - .pll_stable_time = 500, - - /* escape clk : 10MHz */ - .esc_clk = 20 * 1000000, - - /* stop state holding counter after bta change count 0 ~ 0xfff */ - .stop_holding_cnt = 0x7ff, - /* bta timeout 0 ~ 0xff */ - .bta_timeout = 0xff, - /* lp rx timeout 0 ~ 0xffff */ - .rx_timeout = 0xffff, -}; - -static struct exynos_platform_mipi_dsim dsim_platform_data = { - .lcd_panel_info = NULL, - .dsim_config = &dsim_config, -}; - -static struct mipi_dsim_lcd_device mipi_lcd_device = { - .name = "s6e8ax0", - .id = -1, - .bus_id = 0, - .platform_data = (void *)&dsim_platform_data, -}; - -static int mipi_power(void) +int mipi_power(void) { struct pmic *p = pmic_get("MAX77686_PMIC"); @@ -556,77 +407,13 @@ void exynos_reset_lcd(void) s5p_gpio_set_value(&gpio1->f2, 1, 1); } -vidinfo_t panel_info = { - .vl_freq = 60, - .vl_col = 720, - .vl_row = 1280, - .vl_width = 720, - .vl_height = 1280, - .vl_clkp = CONFIG_SYS_HIGH, - .vl_hsp = CONFIG_SYS_LOW, - .vl_vsp = CONFIG_SYS_LOW, - .vl_dp = CONFIG_SYS_LOW, - .vl_bpix = 4, /* Bits per pixel, 2^4 = 16 */ - - /* s6e8ax0 Panel infomation */ - .vl_hspw = 5, - .vl_hbpd = 10, - .vl_hfpd = 10, - - .vl_vspw = 2, - .vl_vbpd = 1, - .vl_vfpd = 13, - .vl_cmd_allow_len = 0xf, - .mipi_enabled = 1, - - .dual_lcd_enabled = 0, - - .init_delay = 0, - .power_on_delay = 25, - .reset_delay = 0, - .interface_mode = FIMD_RGB_INTERFACE, -}; - -void init_panel_info(vidinfo_t *vid) +void exynos_lcd_misc_init(vidinfo_t *vid) { - vid->logo_on = 1; - vid->resolution = HD_RESOLUTION; - vid->rgb_mode = MODE_RGB_P; - - vid->power_on_delay = 30; - - mipi_lcd_device.reverse_panel = 1; - #ifdef CONFIG_TIZEN get_tizen_logo_info(vid); #endif - - strcpy(dsim_platform_data.lcd_panel_name, mipi_lcd_device.name); - dsim_platform_data.mipi_power = mipi_power; - dsim_platform_data.phy_enable = set_mipi_phy_ctrl; - dsim_platform_data.lcd_panel_info = (void *)vid; - exynos_mipi_dsi_register_lcd_device(&mipi_lcd_device); - +#ifdef CONFIG_S6E8AX0 s6e8ax0_init(); - - exynos_set_dsim_platform_data(&dsim_platform_data); -} -#endif /* LCD */ - -#ifdef CONFIG_MISC_INIT_R -int misc_init_r(void) -{ -#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG - set_board_info(); -#endif -#ifdef CONFIG_LCD_MENU - keys_init(); - check_boot_mode(); #endif -#ifdef CONFIG_CMD_BMP - if (panel_info.logo_on) - draw_logo(); -#endif - return 0; } -#endif +#endif /* LCD */ diff --git a/include/configs/trats2.h b/include/configs/trats2.h index 6d389df9df..81945755a1 100644 --- a/include/configs/trats2.h +++ b/include/configs/trats2.h @@ -8,27 +8,17 @@ * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef __CONFIG_H -#define __CONFIG_H +#ifndef __CONFIG_TRATS2_H +#define __CONFIG_TRATS2_H -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_SAMSUNG /* in a SAMSUNG core */ -#define CONFIG_S5P /* which is in a S5P Family */ -#define CONFIG_EXYNOS4 /* which is in a EXYNOS4XXX */ -#define CONFIG_TIZEN /* TIZEN lib */ +#include -#include /* get chip and board defs */ - -#define CONFIG_ARCH_CPU_INIT -#define CONFIG_DISPLAY_CPUINFO -#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_SYS_PROMPT "Trats2 # " /* Monitor Command Prompt */ -#define CONFIG_SKIP_LOWLEVEL_INIT +#undef CONFIG_DEFAULT_DEVICE_TREE +#define CONFIG_DEFAULT_DEVICE_TREE exynos4412-trats2 -#define CONFIG_SYS_CACHELINE_SIZE 32 +#define CONFIG_TIZEN /* TIZEN lib */ #define CONFIG_SYS_L2CACHE_OFF #ifndef CONFIG_SYS_L2CACHE_OFF @@ -36,121 +26,47 @@ #define CONFIG_SYS_PL310_BASE 0x10502000 #endif -#define CONFIG_NR_DRAM_BANKS 4 -#define PHYS_SDRAM_1 0x40000000 /* LDDDR2 DMC 0 */ -#define PHYS_SDRAM_1_SIZE (256 << 20) /* 256 MB in CS 0 */ -#define PHYS_SDRAM_2 0x50000000 /* LPDDR2 DMC 1 */ -#define PHYS_SDRAM_2_SIZE (256 << 20) /* 256 MB in CS 0 */ -#define PHYS_SDRAM_3 0x60000000 /* LPDDR2 DMC 1 */ -#define PHYS_SDRAM_3_SIZE (256 << 20) /* 256 MB in CS 0 */ -#define PHYS_SDRAM_4 0x70000000 /* LPDDR2 DMC 1 */ -#define PHYS_SDRAM_4_SIZE (256 << 20) /* 256 MB in CS 0 */ -#define PHYS_SDRAM_END 0x80000000 - -#define CONFIG_SYS_MEM_TOP_HIDE (1 << 20) /* ram console */ +/* TRATS2 has 4 banks of DRAM */ +#define CONFIG_NR_DRAM_BANKS 4 +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE +#define SDRAM_BANK_SIZE (256 << 20) /* 256 MB */ +/* memtest works on */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000) -#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1) #define CONFIG_SYS_TEXT_BASE 0x78100000 -#define CONFIG_SYS_CLK_FREQ 24000000 - -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_CMDLINE_TAG -#define CONFIG_REVISION_TAG - -/* MACH_TYPE_TRATS2 */ -#define MACH_TYPE_TRATS2 3765 -#define CONFIG_MACH_TYPE MACH_TYPE_TRATS2 - -#define CONFIG_DISPLAY_CPUINFO - #include /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (80 * SZ_1M)) /* select serial console configuration */ #define CONFIG_SERIAL2 +#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +/* Console configuration */ +#define CONFIG_SYS_CONSOLE_INFO_QUIET +#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define CONFIG_CMDLINE_EDITING +#define CONFIG_BOOTARGS "Please use defined boot" +#define CONFIG_BOOTCOMMAND "run mmcboot" +#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0" -#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR \ + - GENERATED_GBL_DATA_SIZE) -/* It should define before config_cmd_default.h */ -#define CONFIG_SYS_NO_FLASH - -/*********************************************************** - * Command definition - ***********************************************************/ -#include - -#undef CONFIG_CMD_ECHO -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_FLASH -#undef CONFIG_CMD_IMLS -#undef CONFIG_CMD_NAND -#undef CONFIG_CMD_MISC -#undef CONFIG_CMD_NFS -#undef CONFIG_CMD_SOURCE -#undef CONFIG_CMD_XIMG -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_I2C -#define CONFIG_CMD_MMC -#define CONFIG_CMD_DFU -#define CONFIG_CMD_GPT -#define CONFIG_CMD_PMIC - -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK - -#define CONFIG_CMD_FAT -#define CONFIG_FAT_WRITE - -/* EXT4 */ -#define CONFIG_CMD_EXT4 -#define CONFIG_CMD_EXT4_WRITE - -/* USB Composite download gadget - g_dnl */ -#define CONFIG_USBDOWNLOAD_GADGET -#define CONFIG_SYS_DFU_DATA_BUF_SIZE SZ_32M -#define DFU_DEFAULT_POLL_TIMEOUT 300 -#define CONFIG_DFU_FUNCTION -#define CONFIG_DFU_MMC - -/* TIZEN THOR downloader support */ -#define CONFIG_CMD_THOR_DOWNLOAD -#define CONFIG_THOR_FUNCTION - -/* USB Samsung's IDs */ -#define CONFIG_G_DNL_VENDOR_NUM 0x04E8 -#define CONFIG_G_DNL_PRODUCT_NUM 0x6601 -#define CONFIG_G_DNL_THOR_VENDOR_NUM CONFIG_G_DNL_VENDOR_NUM -#define CONFIG_G_DNL_THOR_PRODUCT_NUM 0x685D -#define CONFIG_G_DNL_MANUFACTURER "Samsung" - -/* To use the TFTPBOOT over USB, Please enable the CONFIG_CMD_NET */ -#undef CONFIG_CMD_NET - -/* MMC */ -#define CONFIG_GENERIC_MMC -#define CONFIG_MMC -#define CONFIG_S5P_SDHCI -#define CONFIG_SDHCI -#define CONFIG_MMC_SDMA -#define CONFIG_MMC_DEFAULT_DEV 0 - -/* PWM */ -#define CONFIG_PWM - -#define CONFIG_BOOTARGS "Please use defined boot" -#define CONFIG_BOOTCOMMAND "run mmcboot" -#define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0" +#define CONFIG_SYS_MEM_TOP_HIDE (1 << 20) /* ram console */ + +#define CONFIG_SYS_MONITOR_BASE 0x00000000 + +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV CONFIG_MMC_DEFAULT_DEV +#define CONFIG_ENV_SIZE 4096 +#define CONFIG_ENV_OFFSET ((32 - 4) << 10) /* 32KiB - 4KiB */ #define CONFIG_ENV_OVERWRITE -#define CONFIG_SYS_CONSOLE_INFO_QUIET -#define CONFIG_SYS_CONSOLE_IS_IN_ENV #define CONFIG_ENV_VARS_UBOOT_CONFIG #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG @@ -246,49 +162,11 @@ "setenv spl_addr_tmp;\0" \ "fdtaddr=40800000\0" \ -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "Trats2 # " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE 384 /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ - -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* memtest works on */ -#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5000000) -#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x4800000) - -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR \ - - GENERATED_GBL_DATA_SIZE) - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#define CONFIG_SYS_MONITOR_BASE 0x00000000 - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ - -#define CONFIG_ENV_IS_IN_MMC -#define CONFIG_SYS_MMC_ENV_DEV CONFIG_MMC_DEFAULT_DEV -#define CONFIG_ENV_SIZE 4096 -#define CONFIG_ENV_OFFSET ((32 - 4) << 10) /* 32KiB - 4KiB */ -#define CONFIG_EFI_PARTITION -#define CONFIG_PARTITION_UUIDS - -#define CONFIG_BOARD_EARLY_INIT_F - /* I2C */ #include +#define CONFIG_CMD_I2C + #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_S3C24X0 #define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 @@ -318,11 +196,6 @@ int get_soft_i2c_sda_pin(void); #define CONFIG_POWER_MUIC_MAX77693 #define CONFIG_POWER_FG_MAX77693 #define CONFIG_POWER_BATTERY_TRATS2 -#define CONFIG_USB_GADGET -#define CONFIG_USB_GADGET_S3C_UDC_OTG -#define CONFIG_USB_GADGET_DUALSPEED -#define CONFIG_USB_GADGET_VBUS_DRAW 2 -#define CONFIG_USB_CABLE_CHECK /* Common misc for Samsung */ #define CONFIG_MISC_COMMON @@ -362,10 +235,7 @@ int get_soft_i2c_sda_pin(void); #define CONFIG_VIDEO_BMP_GZIP #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((500 * 160 * 4) + 54) -#define CONFIG_CMD_USB_MASS_STORAGE -#define CONFIG_USB_GADGET_MASS_STORAGE - -/* Pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 +#define LCD_XRES 720 +#define LCD_YRES 1280 #endif /* __CONFIG_H */