From: Michal Simek Date: Mon, 14 Sep 2020 13:00:06 +0000 (+0200) Subject: doc: board: xilinx: Add documentation for ZynqMP R5 X-Git-Url: http://git.dujemihanovic.xyz/?a=commitdiff_plain;h=0d4e6a2d3b39437d6bf5e4b07c442af7ace805d2;p=u-boot.git doc: board: xilinx: Add documentation for ZynqMP R5 Add missing documentation for Xilinx ZynqMP R5 configuration with steps how to run it. Signed-off-by: Michal Simek --- diff --git a/doc/board/xilinx/index.rst b/doc/board/xilinx/index.rst index e9560f208f..2e31fe3f3a 100644 --- a/doc/board/xilinx/index.rst +++ b/doc/board/xilinx/index.rst @@ -9,3 +9,4 @@ Xilinx xilinx zynq zynqmp + zynqmp-r5 diff --git a/doc/board/xilinx/zynqmp-r5.rst b/doc/board/xilinx/zynqmp-r5.rst new file mode 100644 index 0000000000..2cd368b030 --- /dev/null +++ b/doc/board/xilinx/zynqmp-r5.rst @@ -0,0 +1,137 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. (C) Copyright 2020 Xilinx, Inc. + +ZYNQMP-R5 +========= + +About this +---------- + +This document describes the information about Xilinx Zynq UltraScale+ MPSOC +U-Boot Cortex R5 support. + +ZynqMP R5 boards +---------------- + +* zynqmp-r5 - U-Boot running on RPU Cortex-R5 + +Building +-------- + +configure and build armv7 toolchain:: + + $ make xilinx_zynqmp_r5_defconfig + $ make + +Notes +^^^^^ + +Output fragment is u-boot. + +Loading +------- + +ZynqMP R5 U-Boot was created for supporting loading OS on RPU. There are two +ways how to start U-Boot on R5. + +Bootgen +^^^^^^^ + +The first way is to use Xilinx FSBL (First stage +bootloader) to load u-boot and start it. The following bif can be used for boot +image generation via Xilinx bootgen utility:: + + + the_ROM_image: + { + [bootloader,destination_cpu=r5-0] fsbl_rpu.elf + [destination_cpu=r5-0]u-boot.elf + } + +Bootgen command for building boot.bin:: + + bootgen -image .bif -r -w -o i boot.bin + + +U-Boot cpu command +^^^^^^^^^^^^^^^^^^ + +The second way to load U-Boot to Cortex R5 is from U-Boot running on A53 as is +visible from the following log:: + + U-Boot SPL 2020.10-rc4-00090-g801b3d5c5757 (Sep 15 2020 - 14:07:24 +0200) + PMUFW: v1.1 + Loading new PMUFW cfg obj (2024 bytes) + EL Level: EL3 + Multiboot: 0 + Trying to boot from MMC2 + spl: could not initialize mmc. error: -19 + Trying to boot from MMC1 + spl_load_image_fat_os: error reading image u-boot.bin, err - -2 + NOTICE: ATF running on XCZU7EG/EV/silicon v4/RTL5.1 at 0xfffea000 + NOTICE: BL31: v2.2(release):v2.2-614-ged9dc512fb9c + NOTICE: BL31: Built : 09:32:09, Mar 13 2020 + + + U-Boot 2020.10-rc4-00090-g801b3d5c5757 (Sep 15 2020 - 14:07:24 +0200) + + Model: ZynqMP ZCU104 RevC + Board: Xilinx ZynqMP + DRAM: 2 GiB + PMUFW: v1.1 + EL Level: EL2 + Chip ID: zu7e + WDT: Started with servicing (60s timeout) + NAND: 0 MiB + MMC: mmc@ff170000: 0 + Loading Environment from FAT... *** Warning - bad CRC, using default environment + + In: serial + Out: serial + Err: serial + Bootmode: LVL_SHFT_SD_MODE1 + Reset reason: SOFT + Net: + ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 12, interface rgmii-id + eth0: ethernet@ff0e0000 + Hit any key to stop autoboot: 0 + ZynqMP> setenv autoload no + ZynqMP> dhcp + BOOTP broadcast 1 + DHCP client bound to address 192.168.0.167 (8 ms) + ZynqMP> tftpboot 20000000 192.168.0.105:u-boot-r5-2.elf + Using ethernet@ff0e0000 device + TFTP from server 192.168.0.105; our IP address is 192.168.0.167 + Filename 'u-boot-r5-2.elf'. + Load address: 0x20000000 + Loading: ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################################################################# + ################ + 376 KiB/s + done + Bytes transferred = 2075464 (1fab48 hex) + ZynqMP> setenv autostart no + ZynqMP> bootelf -p 20000000 + ZynqMP> cpu 4 release 10000000 lockstep + Using TCM jump trampoline for address 0x10000000 + R5 lockstep mode + ZynqMP> + +Then on second uart you can see U-Boot up and running on R5:: + + U-Boot 2020.10-rc4-00071-g7045622cc9ba (Sep 16 2020 - 13:38:53 +0200) + + Model: Xilinx ZynqMP R5 + DRAM: 512 MiB + MMC: + In: serial@ff010000 + Out: serial@ff010000 + Err: serial@ff010000 + Net: No ethernet found. + ZynqMP r5> + +Please make sure MIO pins for uart are properly configured to see output.