Changes for U-Boot 1.1.3:
======================================================================
+* Patch by Leif Lindholm, 23 Sep 2004:
+ add support for the AMD db1550 board
+
+* Patch by Travis Sawyer, 15 Sep 2004:
+ Add CONFIG_SERIAL_MULTI support for ppc4xx,
+ update README.serial_multi
+
* Patches by David Snowdon, 07 Sep 2004:
- add u-boot.hex target in the top level Makefile
- add support for the UNSW/NICTA PLEB 2 board (pleb2)
D: Support for LEOX boards, DS164x RTC
W: http://www.leox.org
+N: Leif Lindholm
+E: leif.lindholm@i3micro.com
+D: Support for AMD dbau1550 board.
+
N: Stephan Linz
E: linz@li-pro.net
D: Support for Nios Stratix Development Kit (DK-1S10)
LIST_mips5kc="purple"
-LIST_au1x00="dbau1000 dbau1100 dbau1500"
+LIST_au1xx0="dbau1000 dbau1100 dbau1500 dbau1550 dbau1550_el"
-LIST_mips="${LIST_mips4kc} ${LIST_mips5kc} ${LIST_au1x00}"
+LIST_mips="${LIST_mips4kc} ${LIST_mips5kc} ${LIST_au1xx0}"
#########################################################################
## i386 Systems
@echo "#define CONFIG_DBAU1500 1" >>include/config.h
@./mkconfig -a dbau1x00 mips mips dbau1x00
+dbau1550_config : unconfig
+ @ >include/config.h
+ @echo "#define CONFIG_DBAU1550 1" >>include/config.h
+ @./mkconfig -a dbau1x00 mips mips dbau1x00
+
+dbau1550_el_config : unconfig
+ @ >include/config.h
+ @echo "#define CONFIG_DBAU1550 1" >>include/config.h
+ @./mkconfig -a dbau1x00 mips mips dbau1x00 "" little
+
#########################################################################
## MIPS64 5Kc
#########################################################################
{
/* Sdram is setup by assembler code */
/* If memory could be changed, we should return the true value here */
- return 64*1024*1024;
+ return MEM_SIZE*1024*1024;
}
#define BCSR_PCMCIA_PC0DRVEN 0x0010
int checkboard (void)
{
u16 status;
- volatile u32 *pcmcia_bcsr = (u32*)(DB1000_BCSR_ADDR+0x10);
- volatile u32 *phy = (u32*)(DB1000_BCSR_ADDR+0xC);
+ volatile u32 *pcmcia_bcsr = (u32*)(DB1XX0_BCSR_ADDR+0x10);
+ volatile u32 *phy = (u32*)(DB1XX0_BCSR_ADDR+0xC);
volatile u32 *sys_counter = (volatile u32*)SYS_COUNTER_CNTRL;
u32 proc_id;
printf ("CPU: Au1100, id: 0x%02x, rev: 0x%02x\n",
(proc_id >> 8) & 0xFF, proc_id & 0xFF);
break;
+ case 3:
+ puts ("Board: DbAu1550\n");
+ printf ("CPU: Au1550, id: 0x%02x, rev: 0x%02x\n",
+ (proc_id >> 8) & 0xFF, proc_id & 0xFF);
+ break;
default:
printf ("Unsupported cpu %d, proc_id=0x%x\n", proc_id >> 24, proc_id);
}
#define AU1500_SYS_ADDR 0xB1900000
#define sys_endian 0x0038
#define CP0_Config0 $16
-#define MEM_1MS ((396000000/1000000) * 1000)
+#define CPU_SCALE ((CFG_MHZ) / 12) /* CPU clock is a multiple of 12 MHz */
+#define MEM_1MS ((CFG_MHZ) * 1000)
.text
.set noreorder
* Switch S1.1 Off(bit7 reads 1) is Little Endian
* Switch S1.1 On (bit7 reads 0) is Big Endian
*/
+#ifdef CONFIG_DBAU1550
+ li t0, MEM_STCFG2
+ li t1, 0x00000040
+ sw t1, 0(t0)
+
+ li t0, MEM_STTIME2
+ li t1, 0x22080a20
+ sw t1, 0(t0)
+
+ li t0, MEM_STADDR2
+ li t1, 0x10c03f00
+ sw t1, 0(t0)
+#else
li t0, MEM_STCFG1
li t1, 0x00000080
sw t1, 0(t0)
li t0, MEM_STADDR1
li t1, 0x10c03f00
sw t1, 0(t0)
+#endif
- li t0, 0xAE000008
- lw t1,0(t0)
+ li t0, DB1XX0_BCSR_ADDR
+ lw t1,8(t0)
andi t1,t1,0x80
beq zero,t1,big_endian
nop
mtc0 zero, CP0_WIRED
nop
+#ifdef CONFIG_DBAU1550
+ /* No workaround if running from ram */
+ lui t0, 0xffc0
+ lui t3, 0xbfc0
+ and t1, ra, t0
+ bne t1, t3, noCacheJump
+ nop
+
+ /*** From AMD YAMON ***/
+ /*
+ * Step 8) Initialize the caches
+ */
+ li t0, (16*1024)
+ li t1, 32
+ li t2, 0x80000000
+ addu t3, t0, t2
+cacheloop:
+ cache 0, 0(t2)
+ cache 1, 0(t2)
+ addu t2, t1
+ bne t2, t3, cacheloop
+ nop
+
+ /* Save return address */
+ move t3, ra
+
+ /* Run from cacheable space now */
+ bal cachehere
+ nop
+cachehere:
+ li t1, ~0x20000000 /* convert to KSEG0 */
+ and t0, ra, t1
+ addi t0, 5*4 /* 5 insns beyond cachehere */
+ jr t0
+ nop
+
+ /* Restore return address */
+ move ra, t3
+
+ /*
+ * Step 9) Initialize the TLB
+ */
+ li t0, 0 # index value
+ li t1, 0x00000000 # entryhi value
+ li t2, 32 # 32 entries
+
+tlbloop:
+ /* Probe TLB for matching EntryHi */
+ mtc0 t1, CP0_ENTRYHI
+ tlbp
+ nop
+
+ /* Examine Index[P], 1=no matching entry */
+ mfc0 t3, CP0_INDEX
+ li t4, 0x80000000
+ and t3, t4, t3
+ addiu t1, t1, 1 # increment t1 (asid)
+ beq zero, t3, tlbloop
+ nop
+
+ /* Initialize the TLB entry */
+ mtc0 t0, CP0_INDEX
+ mtc0 zero, CP0_ENTRYLO0
+ mtc0 zero, CP0_ENTRYLO1
+ mtc0 zero, CP0_PAGEMASK
+ tlbwi
+
+ /* Do it again */
+ addiu t0, t0, 1
+ bne t0, t2, tlbloop
+ nop
+
/* First setup pll:s to make serial work ok */
/* We have a 12 MHz crystal */
li t0, SYS_CPUPLL
- li t1, 0x21 /* 396 MHz */
+ li t1, CPU_SCALE /* CPU clock */
sw t1, 0(t0)
sync
nop
sync
/* Static memory controller */
+ /* RCE0 - can not change while fetching, do so from icache */
+ move t2, ra /* Store return address */
+ bal getAddr
+ nop
- /* RCE0 AMD 29LV640M MirrorBit Flash */
+getAddr:
+ move t1, ra
+ move ra, t2 /* Move return addess back */
+
+ cache 0x14,0(t1)
+ cache 0x14,32(t1)
+ /*** /From YAMON ***/
+
+noCacheJump:
+#endif /* CONFIG_DBAU1550 */
+
+#ifdef CONFIG_DBAU1550
+ li t0, MEM_STTIME0
+ li t1, 0x040181D7
+ sw t1, 0(t0)
+
+ /* RCE0 AMD MirrorBit Flash (?) */
li t0, MEM_STCFG0
- li t1, 0x00000013
+ li t1, 0x00000003
sw t1, 0(t0)
+ li t0, MEM_STADDR0
+ li t1, 0x11803E00
+ sw t1, 0(t0)
+#else /* CONFIG_DBAU1550 */
li t0, MEM_STTIME0
- li t1, 0x040181D7
+ li t1, 0x00014C0F
+ sw t1, 0(t0)
+
+ /* RCE0 AMD 29LV640M MirrorBit Flash */
+ li t0, MEM_STCFG0
+ li t1, 0x00000013
sw t1, 0(t0)
li t0, MEM_STADDR0
li t1, 0x11E03F80
sw t1, 0(t0)
+#endif /* CONFIG_DBAU1550 */
/* RCE1 CPLD Board Logic */
li t0, MEM_STCFG1
li t1, 0x10c03f00
sw t1, 0(t0)
+#ifdef CONFIG_DBAU1550
/* RCE2 CPLD Board Logic */
+ li t0, MEM_STCFG2
+ li t1, 0x00000040
+ sw t1, 0(t0)
+
+ li t0, MEM_STTIME2
+ li t1, 0x22080a20
+ sw t1, 0(t0)
+
+ li t0, MEM_STADDR2
+ li t1, 0x10c03f00
+ sw t1, 0(t0)
+#else
li t0, MEM_STCFG2
li t1, 0x00000000
sw t1, 0(t0)
li t0, MEM_STADDR2
li t1, 0x00000000
sw t1, 0(t0)
+#endif
/* RCE3 PCMCIA 250ns */
li t0, MEM_STCFG3
bne t1, zero, 1b
nop
+#ifdef CONFIG_DBAU1550
+/* SDCS 0,1,2 DDR SDRAM */
+ li t0, MEM_SDMODE0
+ li t1, 0x04276221
+ sw t1, 0(t0)
+
+ li t0, MEM_SDMODE1
+ li t1, 0x04276221
+ sw t1, 0(t0)
+
+ li t0, MEM_SDMODE2
+ li t1, 0x04276221
+ sw t1, 0(t0)
+
+ li t0, MEM_SDADDR0
+ li t1, 0xe21003f0
+ sw t1, 0(t0)
+
+ li t0, MEM_SDADDR1
+ li t1, 0xe21043f0
+ sw t1, 0(t0)
+
+ li t0, MEM_SDADDR2
+ li t1, 0xe21083f0
+ sw t1, 0(t0)
+
+ sync
+
+ li t0, MEM_SDCONFIGA
+ li t1, 0x9030060a /* Program refresh - disabled */
+ sw t1, 0(t0)
+ sync
+
+ li t0, MEM_SDCONFIGB
+ li t1, 0x00028000
+ sw t1, 0(t0)
+ sync
+
+ li t0, MEM_SDPRECMD /* Precharge all */
+ li t1, 0
+ sw t1, 0(t0)
+ sync
+
+ li t0, MEM_SDWRMD0
+ li t1, 0x40000000
+ sw t1, 0(t0)
+ sync
+
+ li t0, MEM_SDWRMD1
+ li t1, 0x40000000
+ sw t1, 0(t0)
+ sync
+
+ li t0, MEM_SDWRMD2
+ li t1, 0x40000000
+ sw t1, 0(t0)
+ sync
+
+ li t0, MEM_SDWRMD0
+ li t1, 0x00000063
+ sw t1, 0(t0)
+ sync
+
+ li t0, MEM_SDWRMD1
+ li t1, 0x00000063
+ sw t1, 0(t0)
+ sync
+
+ li t0, MEM_SDWRMD2
+ li t1, 0x00000063
+ sw t1, 0(t0)
+ sync
+
+ li t0, MEM_SDPRECMD /* Precharge all */
+ sw zero, 0(t0)
+ sync
+
+ /* Issue 2 autoref */
+ li t0, MEM_SDAUTOREF
+ sw zero, 0(t0)
+ sync
+
+ li t0, MEM_SDAUTOREF
+ sw zero, 0(t0)
+ sync
+
+ /* Enable refresh */
+ li t0, MEM_SDCONFIGA
+ li t1, 0x9830060a /* Program refresh - enabled */
+ sw t1, 0(t0)
+ sync
+
+#else /* CONFIG_DBAU1550 */
/* SDCS 0,1 SDRAM */
li t0, MEM_SDMODE0
li t1, 0x005522AA
sw t1, 0(t0)
sync
+#endif /* CONFIG_DBAU1550 */
/* wait 1mS after setup */
li t1, MEM_1MS
1: add t1, -1
#elif defined(CONFIG_8xx_CONS_SCC1) || defined(CONFIG_8xx_CONS_SCC2) \
|| defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4)
return &serial_scc_device;
+#elif defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
+ || defined(CONFIG_405EP)
+ return &serial0_device;
#else
#error No default console
#endif
serial_register (&serial_scc_device);
#endif
+#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
+ || defined(CONFIG_405EP)
+ serial_register(&serial0_device);
+ serial_register(&serial1_device);
+#endif
+
serial_assign (default_serial_console ()->name);
}
#define ETH0_BASE AU1500_ETH0_BASE
#define MAC0_ENABLE AU1500_MAC0_ENABLE
#else
+#ifdef CONFIG_AU1550
+#define ETH0_BASE AU1550_ETH0_BASE
+#define MAC0_ENABLE AU1550_MAC0_ENABLE
+#else
#error "No valid cpu set"
#endif
#endif
#endif
+#endif
#include <common.h>
#include <malloc.h>
volatile u32 *uart_clk = (volatile u32*)(UART0_ADDR+UART_CLK);
volatile u32 *uart_lcr = (volatile u32*)(UART0_ADDR+UART_LCR);
- /* Set baudrate to 115200 */
- *uart_clk = 0x36;
+ /* Set baudrate - FIXME for bus speeds != CPU/2 */
+ *uart_clk = ((CFG_HZ/(CONFIG_BAUDRATE * 64)));
/* Set parity, stop bits and word length to 8N1 */
*uart_lcr = UART_LCR_WLEN8;
* LICENSED MATERIAL - PROGRAM PROPERTY OF I B M
*/
/*------------------------------------------------------------------------------- */
-
+/*
+ * Travis Sawyer 15 September 2004
+ * Added CONFIG_SERIAL_MULTI support
+ */
#include <common.h>
#include <commproc.h>
#include <asm/processor.h>
#include <watchdog.h>
#include "vecnum.h"
+#ifdef CONFIG_SERIAL_MULTI
+#include <serial.h>
+#endif
+
#ifdef CONFIG_SERIAL_SOFTWARE_FIFO
#include <malloc.h>
#endif
#define asyncXOFFchar 0x13
#define asyncXONchar 0x11
-
/*
* Minimal serial functions needed to use one of the SMC ports
* as serial console interface.
return (0);
}
-
void serial_setbrg (void)
{
DECLARE_GLOBAL_DATA_PTR;
out8 (SPU_BASE + spu_BRateDivh, ((br_reg & 0xff00) >> 8)); /* ... */
}
-
void serial_putc (const char c)
{
if (c == '\n')
}
}
-
void serial_puts (const char *s)
{
while (*s) {
}
}
-
int serial_getc ()
{
unsigned char status = 0;
return (0x000000ff & (int) in8 (asyncRxBufferport1));
}
-
int serial_tstc ()
{
unsigned char status;
#endif /* CONFIG_IOP480 */
-
/*****************************************************************************/
#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) || defined(CONFIG_405EP)
/*#define asyncTxBufferport1 ACTING_UART0_BASE+0x00 */
/*#define asyncRxBufferport1 ACTING_UART0_BASE+0x00 */
-
#ifdef CONFIG_SERIAL_SOFTWARE_FIFO
/*-----------------------------------------------------------------------------+
| Fifo
volatile static serial_buffer_t buf_info;
#endif
-
#if defined(CONFIG_440) && !defined(CFG_EXT_SERIAL_CLOCK)
static void serial_divs (int baudrate, unsigned long *pudiv,
unsigned short *pbdiv )
}
#endif /* defined(CONFIG_440) && !defined(CFG_EXT_SERIAL_CLK */
-
/*
* Minimal serial functions needed to use one of the SMC ports
* as serial console interface.
*/
#if defined(CONFIG_440)
-int serial_init (void)
+#if defined(CONFIG_SERIAL_MULTI)
+int serial_init_dev (unsigned long dev_base)
+#else
+int serial_init(void)
+#endif
{
DECLARE_GLOBAL_DATA_PTR;
#endif
#if defined(CONFIG_440_GX)
+#if defined(CONFIG_SERIAL_MULTI)
+ if (UART0_BASE == dev_base) {
+ mfsdr(UART0_SDR,reg);
+ reg &= ~CR0_MASK;
+ } else {
+ mfsdr(UART1_SDR,reg);
+ reg &= ~CR0_MASK;
+ }
+#else
mfsdr(UART0_SDR,reg);
reg &= ~CR0_MASK;
+#endif
#else
reg = mfdcr(cntrl0) & ~CR0_MASK;
#endif /* CONFIG_440_GX */
#if defined(CONFIG_440_GX)
reg |= udiv << CR0_UDIV_POS; /* set the UART divisor */
+#if defined(CONFIG_SERIAL_MULTI)
+ if (UART0_BASE == dev_base) {
+ mtsdr (UART0_SDR,reg);
+ } else {
+ mtsdr (UART1_SDR,reg);
+ }
+#else
mtsdr (UART0_SDR,reg);
+#endif
#else
reg |= (udiv - 1) << CR0_UDIV_POS; /* set the UART divisor */
mtdcr (cntrl0, reg);
#endif
+
+#if defined(CONFIG_SERIAL_MULTI)
+ out8 (dev_base + UART_LCR, 0x80); /* set DLAB bit */
+ out8 (dev_base + UART_DLL, bdiv); /* set baudrate divisor */
+ out8 (dev_base + UART_DLM, bdiv >> 8);/* set baudrate divisor */
+ out8 (dev_base + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */
+ out8 (dev_base + UART_FCR, 0x00); /* disable FIFO */
+ out8 (dev_base + UART_MCR, 0x00); /* no modem control DTR RTS */
+ val = in8 (dev_base + UART_LSR); /* clear line status */
+ val = in8 (dev_base + UART_RBR); /* read receive buffer */
+ out8 (dev_base + UART_SCR, 0x00); /* set scratchpad */
+ out8 (dev_base + UART_IER, 0x00); /* set interrupt enable reg */
+#else
out8 (ACTING_UART0_BASE + UART_LCR, 0x80); /* set DLAB bit */
out8 (ACTING_UART0_BASE + UART_DLL, bdiv); /* set baudrate divisor */
out8 (ACTING_UART0_BASE + UART_DLM, bdiv >> 8);/* set baudrate divisor */
val = in8 (ACTING_UART0_BASE + UART_RBR); /* read receive buffer */
out8 (ACTING_UART0_BASE + UART_SCR, 0x00); /* set scratchpad */
out8 (ACTING_UART0_BASE + UART_IER, 0x00); /* set interrupt enable reg */
-
+#endif
return (0);
}
#else /* !defined(CONFIG_440) */
+#if defined(CONFIG_SERIAL_MULTI)
+int serial_init_dev (unsigned long dev_base)
+#else
int serial_init (void)
+#endif
{
DECLARE_GLOBAL_DATA_PTR;
tmp = gd->baudrate * udiv * 16;
bdiv = (clk + tmp / 2) / tmp;
+#if defined(CONFIG_SERIAL_MULTI)
+ out8 (dev_base + UART_LCR, 0x80); /* set DLAB bit */
+ out8 (dev_base + UART_DLL, bdiv); /* set baudrate divisor */
+ out8 (dev_base + UART_DLM, bdiv >> 8);/* set baudrate divisor */
+ out8 (dev_base + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */
+ out8 (dev_base + UART_FCR, 0x00); /* disable FIFO */
+ out8 (dev_base + UART_MCR, 0x00); /* no modem control DTR RTS */
+ val = in8 (dev_base + UART_LSR); /* clear line status */
+ val = in8 (dev_base + UART_RBR); /* read receive buffer */
+ out8 (dev_base + UART_SCR, 0x00); /* set scratchpad */
+ out8 (dev_base + UART_IER, 0x00); /* set interrupt enable reg */
+#else
out8 (ACTING_UART0_BASE + UART_LCR, 0x80); /* set DLAB bit */
out8 (ACTING_UART0_BASE + UART_DLL, bdiv); /* set baudrate divisor */
out8 (ACTING_UART0_BASE + UART_DLM, bdiv >> 8);/* set baudrate divisor */
val = in8 (ACTING_UART0_BASE + UART_RBR); /* read receive buffer */
out8 (ACTING_UART0_BASE + UART_SCR, 0x00); /* set scratchpad */
out8 (ACTING_UART0_BASE + UART_IER, 0x00); /* set interrupt enable reg */
-
+#endif
return (0);
}
#endif /* if defined(CONFIG_440) */
+#if defined(CONFIG_SERIAL_MULTI)
+void serial_setbrg_dev (unsigned long dev_base)
+#else
void serial_setbrg (void)
+#endif
{
DECLARE_GLOBAL_DATA_PTR;
tmp = gd->baudrate * udiv * 16;
bdiv = (clk + tmp / 2) / tmp;
+#if defined(CONFIG_SERIAL_MULTI)
+ out8 (dev_base + UART_LCR, 0x80); /* set DLAB bit */
+ out8 (dev_base + UART_DLL, bdiv); /* set baudrate divisor */
+ out8 (dev_base + UART_DLM, bdiv >> 8);/* set baudrate divisor */
+ out8 (dev_base + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */
+#else
out8 (ACTING_UART0_BASE + UART_LCR, 0x80); /* set DLAB bit */
out8 (ACTING_UART0_BASE + UART_DLL, bdiv); /* set baudrate divisor */
out8 (ACTING_UART0_BASE + UART_DLM, bdiv >> 8);/* set baudrate divisor */
out8 (ACTING_UART0_BASE + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */
+#endif
}
-
+#if defined(CONFIG_SERIAL_MULTI)
+void serial_putc_dev (unsigned long dev_base, const char c)
+#else
void serial_putc (const char c)
+#endif
{
int i;
if (c == '\n')
+#if defined(CONFIG_SERIAL_MULTI)
+ serial_putc_dev (dev_base, '\r');
+#else
serial_putc ('\r');
+#endif
/* check THRE bit, wait for transmiter available */
for (i = 1; i < 3500; i++) {
+#if defined(CONFIG_SERIAL_MULTI)
+ if ((in8 (dev_base + UART_LSR) & 0x20) == 0x20)
+#else
if ((in8 (ACTING_UART0_BASE + UART_LSR) & 0x20) == 0x20)
+#endif
break;
udelay (100);
}
+#if defined(CONFIG_SERIAL_MULTI)
+ out8 (dev_base + UART_THR, c); /* put character out */
+#else
out8 (ACTING_UART0_BASE + UART_THR, c); /* put character out */
+#endif
}
-
+#if defined(CONFIG_SERIAL_MULTI)
+void serial_puts_dev (unsigned long dev_base, const char *s)
+#else
void serial_puts (const char *s)
+#endif
{
while (*s) {
+#if defined(CONFIG_SERIAL_MULTI)
+ serial_putc_dev (dev_base, *s++);
+#else
serial_putc (*s++);
+#endif
}
}
-
-int serial_getc ()
+#if defined(CONFIG_SERIAL_MULTI)
+int serial_getc_dev (unsigned long dev_base)
+#else
+int serial_getc (void)
+#endif
{
unsigned char status = 0;
#if defined(CONFIG_HW_WATCHDOG)
WATCHDOG_RESET (); /* Reset HW Watchdog, if needed */
#endif /* CONFIG_HW_WATCHDOG */
+#if defined(CONFIG_SERIAL_MULTI)
+ status = in8 (dev_base + UART_LSR);
+#else
status = in8 (ACTING_UART0_BASE + UART_LSR);
+#endif
if ((status & asyncLSRDataReady1) != 0x0) {
break;
}
asyncLSROverrunError1 |
asyncLSRParityError1 |
asyncLSRBreakInterrupt1 )) != 0) {
+#if defined(CONFIG_SERIAL_MULTI)
+ out8 (dev_base + UART_LSR,
+#else
out8 (ACTING_UART0_BASE + UART_LSR,
+#endif
asyncLSRFramingError1 |
asyncLSROverrunError1 |
asyncLSRParityError1 |
asyncLSRBreakInterrupt1);
}
}
+#if defined(CONFIG_SERIAL_MULTI)
+ return (0x000000ff & (int) in8 (dev_base));
+#else
return (0x000000ff & (int) in8 (ACTING_UART0_BASE));
+#endif
}
-
-int serial_tstc ()
+#if defined(CONFIG_SERIAL_MULTI)
+int serial_tstc_dev (unsigned long dev_base)
+#else
+int serial_tstc (void)
+#endif
{
unsigned char status;
+#if defined(CONFIG_SERIAL_MULTI)
+ status = in8 (dev_base + UART_LSR);
+#else
status = in8 (ACTING_UART0_BASE + UART_LSR);
+#endif
if ((status & asyncLSRDataReady1) != 0x0) {
return (1);
}
asyncLSROverrunError1 |
asyncLSRParityError1 |
asyncLSRBreakInterrupt1 )) != 0) {
+#if defined(CONFIG_SERIAL_MULTI)
+ out8 (dev_base + UART_LSR,
+#else
out8 (ACTING_UART0_BASE + UART_LSR,
+#endif
asyncLSRFramingError1 |
asyncLSROverrunError1 |
asyncLSRParityError1 |
return 0;
}
-
#ifdef CONFIG_SERIAL_SOFTWARE_FIFO
void serial_isr (void *arg)
} else {
space = rx_get - rx_put;
}
- while (serial_tstc ()) {
- c = serial_getc ();
+ while (serial_tstc_dev (ACTING_UART0_BASE)) {
+ c = serial_getc_dev (ACTING_UART0_BASE);
if (space) {
buf_info.rx_buffer[rx_put++] = c;
space--;
#endif /* CONFIG_SERIAL_SOFTWARE_FIFO */
-
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
/*
AS HARNOIS : according to CONFIG_KGDB_SER_INDEX kgdb uses serial port
out8 (ACTING_UART1_BASE + UART_IER, 0x00); /* set interrupt enable reg */
}
-
void putDebugChar (const char c)
{
if (c == '\n')
while ((in8 (ACTING_UART1_BASE + UART_LSR) & 0x20) != 0x20);
}
-
void putDebugStr (const char *s)
{
while (*s) {
}
}
-
int getDebugChar (void)
{
unsigned char status = 0;
return (0x000000ff & (int) in8 (ACTING_UART1_BASE));
}
-
void kgdb_interruptible (int yes)
{
return;
#endif /* (CONFIG_KGDB_SER_INDEX & 2) */
#endif /* CFG_CMD_KGDB */
+
+#if defined(CONFIG_SERIAL_MULTI)
+int serial0_init(void)
+{
+ return (serial_init_dev(UART0_BASE));
+}
+
+int serial1_init(void)
+{
+ return (serial_init_dev(UART1_BASE));
+}
+void serial0_setbrg (void)
+{
+ serial_setbrg_dev(UART0_BASE);
+}
+void serial1_setbrg (void)
+{
+ serial_setbrg_dev(UART1_BASE);
+}
+
+void serial0_putc(const char c)
+{
+ serial_putc_dev(UART0_BASE,c);
+}
+
+void serial1_putc(const char c)
+{
+ serial_putc_dev(UART1_BASE, c);
+}
+void serial0_puts(const char *s)
+{
+ serial_puts_dev(UART0_BASE, s);
+}
+
+void serial1_puts(const char *s)
+{
+ serial_puts_dev(UART1_BASE, s);
+}
+
+int serial0_getc(void)
+{
+ return(serial_getc_dev(UART0_BASE));
+}
+
+int serial1_getc(void)
+{
+ return(serial_getc_dev(UART1_BASE));
+}
+int serial0_tstc(void)
+{
+ return (serial_tstc_dev(UART0_BASE));
+}
+
+int serial1_tstc(void)
+{
+ return (serial_tstc_dev(UART1_BASE));
+}
+
+struct serial_device serial0_device =
+{
+ "serial0",
+ "UART0",
+ serial0_init,
+ serial0_setbrg,
+ serial0_getc,
+ serial0_tstc,
+ serial0_putc,
+ serial0_puts,
+};
+
+struct serial_device serial1_device =
+{
+ "serial1",
+ "UART1",
+ serial1_init,
+ serial1_setbrg,
+ serial1_getc,
+ serial1_tstc,
+ serial1_putc,
+ serial1_puts,
+};
+#endif /* CONFIG_SERIAL_MULTI */
+
#endif /* CONFIG_405GP || CONFIG_405CR */
intended to allow for modem dial-in / dial-out while still being able
to use a serial console on a (different) serial port.
+MPC8XX Specific
+===============
At the moment, the ports must be split on a SMC and a SCC port on a
8xx processor; other configurations are not (yet) supported.
After that press 'enter' at the SCC console. Note that baudrates <38400
are not allowed on LWMON with watchdog enabled (see CFG_BAUDRATE_TABLE in
include/configs/lwmon.h).
+
+
+PPC4XX Specific
+===============
+*) The default console is UART0
+
+*) The console can be switched to UART1 by any of the following commands:
+ setenv stdout serial1
+ setenv stderr serial1
+ setenv stdin serial1
+
+*) The console can be switched to UART0 by any of the following commands:
+ setenv stdout serial0
+ setenv stderr serial0
+ setenv stdin serial0
#define CP0_DEBUG $23
/* SDRAM Controller */
+#ifdef CONFIG_AU1550
+
+#define MEM_SDMODE0 0xB4000800
+#define MEM_SDMODE1 0xB4000808
+#define MEM_SDMODE2 0xB4000810
+
+#define MEM_SDADDR0 0xB4000820
+#define MEM_SDADDR1 0xB4000828
+#define MEM_SDADDR2 0xB4000830
+
+#define MEM_SDCONFIGA 0xB4000840
+#define MEM_SDCONFIGB 0xB4000848
+#define MEM_SDPRECMD 0xB40008c0
+#define MEM_SDAUTOREF 0xB40008c8
+
+#define MEM_SDWRMD0 0xB4000880
+#define MEM_SDWRMD1 0xB4000888
+#define MEM_SDWRMD2 0xB4000890
+
+#else /* CONFIG_AU1550 */
+
#define MEM_SDMODE0 0xB4000000
#define MEM_SDMODE1 0xB4000004
#define MEM_SDMODE2 0xB4000008
#define MEM_SDWRMD1 0xB4000028
#define MEM_SDWRMD2 0xB400002C
+#endif /* CONFIG_AU1550 */
+
#define MEM_SDSLEEP 0xB4000030
#define MEM_SDSMCKE 0xB4000034
#define AU1500_ETH0_BASE 0xB1500000
#define AU1500_ETH1_BASE 0xB1510000
#define AU1100_ETH0_BASE 0xB0500000
+#define AU1550_ETH0_BASE 0xB0500000
+#define AU1550_ETH1_BASE 0xB0510000
/* 4 byte offsets from AU1000_ETH_BASE */
#define MAC_CONTROL 0x0
#define AU1500_MAC0_ENABLE 0xB1520000
#define AU1500_MAC1_ENABLE 0xB1520004
#define AU1100_MAC0_ENABLE 0xB0520000
+#define AU1550_MAC0_ENABLE 0xB0520000
+#define AU1550_MAC1_ENABLE 0xB0520004
#define MAC_EN_CLOCK_ENABLE (1<<0)
#define MAC_EN_RESET0 (1<<1)
#define AC97C_RS (1<<1)
#define AC97C_CE (1<<0)
+#define DB1000_BCSR_ADDR 0xAE000000
+#define DB1550_BCSR_ADDR 0xAF000000
+
+#ifdef CONFIG_DBAU1550
+#define DB1XX0_BCSR_ADDR DB1550_BCSR_ADDR
+#else
+#define DB1XX0_BCSR_ADDR DB1000_BCSR_ADDR
+#endif
+
#ifdef CONFIG_SOC_AU1500
/* Au1500 PCI Controller */
#define Au1500_CFG_BASE 0xB4005000 /* virtual, kseg0 addr */
#ifdef CONFIG_DBAU1500
#define CONFIG_AU1500 1
#else
+#ifdef CONFIG_DBAU1550
+/* Cabernet */
+#define CONFIG_AU1550 1
+#else
#error "No valid board set"
#endif
#endif
#endif
+#endif
#define CONFIG_ETHADDR DE:AD:BE:EF:01:01 /* Ethernet address */
"bootfile=/tftpboot/vmlinux.srec\0" \
"load=tftp 80500000 $(u-boot)\0" \
""
+
+#ifdef CONFIG_DBAU1550
+/* Boot from flash by default, revert to bootp */
+#define CONFIG_BOOTCOMMAND "bootm 0xbfc20000; bootp; bootm"
+
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_FLASH | CFG_CMD_LOADB | CFG_CMD_NET) & \
+ ~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FPGA | CFG_CMD_IDE | \
+ CFG_CMD_MII | CFG_CMD_RUN | CFG_CMD_BDI | CFG_CMD_BEDBUG | \
+ CFG_CMD_NFS | CFG_CMD_ELF | CFG_CMD_PCMCIA | CFG_CMD_I2C))
+#else /* CONFIG_DBAU1550 */
/* Boot from Compact flash partition 2 as default */
#define CONFIG_BOOTCOMMAND "ide reset;disk 0x81000000 0:2;bootm"
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \
- CFG_CMD_IDE | \
- CFG_CMD_DHCP | \
- CFG_CMD_ELF ) & \
- ~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FLASH | CFG_CMD_FPGA | \
- CFG_CMD_MII | CFG_CMD_LOADS | CFG_CMD_RUN | CFG_CMD_LOADB | CFG_CMD_ELF | \
- CFG_CMD_BDI | CFG_CMD_BEDBUG))
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_IDE | CFG_CMD_DHCP | CFG_CMD_ELF) & \
+ ~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FLASH | CFG_CMD_FPGA | \
+ CFG_CMD_MII | CFG_CMD_LOADS | CFG_CMD_RUN | CFG_CMD_LOADB | \
+ CFG_CMD_ELF | CFG_CMD_BDI | CFG_CMD_BEDBUG))
+#endif /* CONFIG_DBAU1550 */
+
#include <cmd_confdefs.h>
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "DbAu1x00 # " /* Monitor Command Prompt */
+
+#define CFG_PROMPT "DbAu1xx0 # " /* Monitor Command Prompt */
+
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args*/
#define CFG_BOOTPARAMS_LEN 128*1024
-#define CFG_HZ 396000000 /* FIXME causes overflow in net.c */
+#define CFG_MHZ 396
+
+#if (CFG_MHZ % 12) != 0
+#error "Invalid CPU frequency - must be multiple of 12!"
+#endif
+
+#define CFG_HZ (CFG_MHZ * 1000000) /* FIXME causes overflow in net.c */
#define CFG_SDRAM_BASE 0x80000000 /* Cached addr */
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
+#ifdef CONFIG_DBAU1550
+
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT (512) /* max number of sectors on one chip */
+
+#define PHYS_FLASH_1 0xb8000000 /* Flash Bank #1 */
+#define PHYS_FLASH_2 0xbc000000 /* Flash Bank #2 */
+
+#define CFG_FLASH_BANKS_LIST {PHYS_FLASH_1, PHYS_FLASH_2}
+
+#else /* CONFIG_DBAU1550 */
+
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT (128) /* max number of sectors on one chip */
#define PHYS_FLASH_1 0xbec00000 /* Flash Bank #1 */
#define PHYS_FLASH_2 0xbfc00000 /* Flash Bank #2 */
+#endif /* CONFIG_DBAU1550 */
+
+#define CFG_FLASH_CFI 1
+#define CFG_FLASH_CFI_DRIVER 1
+
/* The following #defines are needed to get flash environment right */
#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_MONITOR_LEN (192 << 10)
#define CONFIG_NET_MULTI
+#ifdef CONFIG_DBAU1550
+#define MEM_SIZE 192
+#else
+#define MEM_SIZE 64
+#endif
+
#define CONFIG_MEMSIZE_IN_BYTES
+#ifndef CONFIG_DBAU1550
/*---ATA PCMCIA ------------------------------------*/
#define CFG_PCMCIA_MEM_SIZE 0x4000000 /* Offset to slot 1 FIXME!!! */
#define CFG_PCMCIA_MEM_ADDR 0x20000000
/* Offset for alternate registers */
#define CFG_ATA_ALT_OFFSET 0x0100
+#endif /* CONFIG_DBAU1550 */
/*-----------------------------------------------------------------------
* Cache Configuration
#define CFG_ICACHE_SIZE 16384
#define CFG_CACHELINE_SIZE 32
-#define DB1000_BCSR_ADDR 0xAE000000
-
#endif /* __CONFIG_H */
extern struct serial_device serial_scc_device;
extern struct serial_device * default_serial_console (void);
+#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
+ || defined(CONFIG_405EP)
+extern struct serial_device serial0_device;
+extern struct serial_device serial1_device;
+#endif
+
+
extern void serial_initialize(void);
extern void serial_devices_init(void);
extern int serial_assign(char * name);
projects / u-boot.git / commitdiff