Changes for U-Boot 1.1.4:
======================================================================
+* Support passing of OF flat trees to the kernel.
+ Patch by Pantelis Antoniou, 04 Sep 2005
+
* Cleanup
* Add support for NetSilicon NS7520 processor.
logodl_config : unconfig
@./mkconfig $(@:_config=) arm pxa logodl
+pxa255_idp_config: unconfig
+ @./mkconfig $(@:_config=) arm pxa pxa255_idp
+
wepep250_config : unconfig
@./mkconfig $(@:_config=) arm pxa wepep250
expect it to be in bytes, others in MB.
Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
+ CONFIG_OF_FLAT_TREE
+
+ New kernel versions are expecting firmware settings to be
+ passed using flat open firmware trees.
+ The environment variable "disable_of", when set, disables this
+ functionality.
+
+ CONFIG_OF_FLAT_TREE_MAX_SIZE
+
+ The maximum size of the constructed OF tree.
+
+ OF_CPU - The proper name of the cpus node.
+ OF_TBCLK - The timebase frequency.
+
- Serial Ports:
CFG_PL010_SERIAL
long mear1;
long emear1;
- size = get_ram_size(CFG_SDRAM_BASE, CFG_MAX_RAM_SIZE);
+ size = get_ram_size (CFG_SDRAM_BASE, CFG_MAX_RAM_SIZE);
new_bank0_end = size - 1;
- mear1 = mpc824x_mpc107_getreg(MEAR1);
- emear1 = mpc824x_mpc107_getreg(EMEAR1);
+ mear1 = mpc824x_mpc107_getreg (MEAR1);
+ emear1 = mpc824x_mpc107_getreg (EMEAR1);
mear1 = (mear1 & 0xFFFFFF00) |
((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
emear1 = (emear1 & 0xFFFFFF00) |
((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
- mpc824x_mpc107_setreg(MEAR1, mear1);
- mpc824x_mpc107_setreg(EMEAR1, emear1);
+ mpc824x_mpc107_setreg (MEAR1, mear1);
+ mpc824x_mpc107_setreg (EMEAR1, emear1);
return (size);
}
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0f, PCI_ANY_ID,
pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
PCI_ENET0_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER } },
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x10, PCI_ANY_ID,
pci_cfgfunc_config_device, { PCI_ENET1_IOADDR,
PCI_ENET1_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER } },
{ }
};
#endif
#endif
};
-void pci_init_board(void)
+void pci_init_board (void)
{
- pci_mpc824x_init(&hose);
+ pci_mpc824x_init (&hose);
}
-int write_flash(char *addr, char value)
+int write_flash (char *addr, char value)
{
char *adr = (char *)0xFF800000;
int cnt = 0;
char status,oldstatus;
- *(adr+0x55) = 0xAA;
- udelay(1);
- *(adr+0xAA) = 0x55;
- udelay(1);
- *(adr+0x55) = 0xA0;
- udelay(1);
+ *(adr+0x55) = 0xAA; udelay (1);
+ *(adr+0xAA) = 0x55; udelay (1);
+ *(adr+0x55) = 0xA0; udelay (1);
*addr = value;
status = *addr;
- do{
-
+ do {
oldstatus = status;
status = *addr;
- if ((oldstatus & 0x40) == (status & 0x40)){
+ if ((oldstatus & 0x40) == (status & 0x40)) {
return 4;
}
cnt++;
- if (cnt > 10000){
+ if (cnt > 10000) {
return 2;
}
- }while( (status & 0x20) == 0 );
+ } while ( (status & 0x20) == 0 );
oldstatus = *addr;
status = *addr;
- if ((oldstatus & 0x40) == (status & 0x40)) return 0;
- else {
+ if ((oldstatus & 0x40) == (status & 0x40)) {
+ return 0;
+ } else {
*(adr+0x55) = 0xF0;
return 1;
}
}
-unsigned update_flash(unsigned char* buf){
- switch((*buf) & 0x3){
- case TRY_WORKING:
- printf("found 3 and converted it to 2\n");
- write_flash(buf, (*buf) & 0xFE);
- *((unsigned char *)0xFF800000) = 0xF0;
- udelay(100);
- printf("buf [%#010x] %#010x\n",buf,(*buf));
- case BOOT_WORKING :
- return BOOT_WORKING;
+unsigned update_flash (unsigned char *buf)
+{
+ switch ((*buf) & 0x3) {
+ case TRY_WORKING:
+ printf ("found 3 and converted it to 2\n");
+ write_flash (buf, (*buf) & 0xFE);
+ *((unsigned char *)0xFF800000) = 0xF0;
+ udelay (100);
+ printf ("buf [%#010x] %#010x\n", buf, (*buf));
+ /* XXX - fall through??? */
+ case BOOT_WORKING :
+ return BOOT_WORKING;
}
return BOOT_DEFAULT;
}
-unsigned scan_flash(void)
+unsigned scan_flash (void)
{
char section[] = "kernel";
- ulong sp;
int cfgFileLen = (CFG_FLASH_ERASE_SECTOR_LENGTH >> 1);
int sectionPtr = 0;
int foundItem = 0; /* 0: None, 1: section found, 2: "=" found */
buf = (unsigned char*)(CFG_FLASH_RANGE_BASE + CFG_FLASH_RANGE_SIZE \
- CFG_FLASH_ERASE_SECTOR_LENGTH);
- for(bufPtr = 0; bufPtr < cfgFileLen; ++bufPtr){
+ for (bufPtr = 0; bufPtr < cfgFileLen; ++bufPtr) {
if ((buf[bufPtr]==0xFF) && (*(int*)(buf+bufPtr)==0xFFFFFFFF)) {
return BOOT_DEFAULT;
}
- switch(foundItem)
- {
- /* This is the scanning loop, we try to find a particular
- * quoted value
- */
- case 0:
- if((section[sectionPtr] == 0)){
- ++foundItem;
- }
- else if(buf[bufPtr] == section[sectionPtr]){
- ++sectionPtr;
- }
- else {
- sectionPtr = 0;
- }
- break;
- case 1:
+ /* This is the scanning loop, we try to find a particular
+ * quoted value
+ */
+ switch (foundItem) {
+ case 0:
+ if ((section[sectionPtr] == 0)) {
++foundItem;
- break;
- case 2:
- ++foundItem;
- break;
- case 3:
- default:
- return update_flash(buf[bufPtr - 1]);
+ } else if (buf[bufPtr] == section[sectionPtr]) {
+ ++sectionPtr;
+ } else {
+ sectionPtr = 0;
+ }
+ break;
+ case 1:
+ ++foundItem;
+ break;
+ case 2:
+ ++foundItem;
+ break;
+ case 3:
+ default:
+ return update_flash (&buf[bufPtr - 1]);
}
}
- printf("Failed to read %s\n",section);
+ printf ("Failed to read %s\n",section);
return BOOT_DEFAULT;
}
-TSBootInfo* find_boot_info(void)
+TSBootInfo* find_boot_info (void)
{
- unsigned bootimage = scan_flash();
- TSBootInfo* info = (TSBootInfo*)malloc(sizeof(TSBootInfo));
-
- switch(bootimage){
- case TRY_WORKING:
- info->address = CFG_WORKING_KERNEL_ADDRESS;
- break;
- case BOOT_WORKING :
- info->address = CFG_WORKING_KERNEL_ADDRESS;
- break;
- case BOOT_DEFAULT:
- default:
- info->address= CFG_DEFAULT_KERNEL_ADDRESS;
+ unsigned bootimage = scan_flash ();
+ TSBootInfo* info = (TSBootInfo*)malloc (sizeof(TSBootInfo));
+
+ switch (bootimage) {
+ case TRY_WORKING:
+ info->address = CFG_WORKING_KERNEL_ADDRESS;
+ break;
+ case BOOT_WORKING :
+ info->address = CFG_WORKING_KERNEL_ADDRESS;
+ break;
+ case BOOT_DEFAULT:
+ default:
+ info->address= CFG_DEFAULT_KERNEL_ADDRESS;
}
info->size = *((unsigned int *)(info->address ));
return info;
}
-void barcobcd_boot(void)
+void barcobcd_boot (void)
{
TSBootInfo* start;
char *bootm_args[2];
char *buf;
int cnt;
+ extern int do_bootm (cmd_tbl_t *, int, int, char *[]);
buf = (char *)(0x00800000);
/* make certain there are enough chars to print the command line here!
*/
- bootm_args[0]=(char *)malloc(16*sizeof(char));
- bootm_args[1]=(char *)malloc(16*sizeof(char));
+ bootm_args[0] = (char *)malloc (16*sizeof(char));
+ bootm_args[1] = (char *)malloc (16*sizeof(char));
- start = find_boot_info();
+ start = find_boot_info ();
- printf("Booting kernel at address %#10x with size %#10x\n",
+ printf ("Booting kernel at address %#10x with size %#10x\n",
start->address, start->size);
/* give length of the kernel image to bootm */
- sprintf(bootm_args[0],"%x",start->size);
+ sprintf (bootm_args[0],"%x",start->size);
/* give address of the kernel image to bootm */
- sprintf(bootm_args[1],"%x",buf);
+ sprintf (bootm_args[1],"%x",buf);
- printf("flash address: %#10x\n",start->address+8);
- printf("buf address: %#10x\n",buf);
+ printf ("flash address: %#10x\n",start->address+8);
+ printf ("buf address: %#10x\n",buf);
/* aha, we reserve 8 bytes here... */
- for (cnt = 0; cnt < start->size ; cnt++){
+ for (cnt = 0; cnt < start->size ; cnt++) {
buf[cnt] = ((char *)start->address)[cnt+8];
}
/* initialise RAM memory */
*((unsigned int *)0xFEC00000) = 0x00141A98;
- do_bootm(NULL,0,2,bootm_args);
+ do_bootm (NULL,0,2,bootm_args);
}
-int barcobcd_boot_image(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+int barcobcd_boot_image (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
#if 0
if (argc > 1) {
return 1;
}
#endif
- barcobcd_boot();
+ barcobcd_boot ();
return 0;
}
/* Currently, boot_working and boot_default are the same command. This is
* left in here to see what we'll do in the future */
-U_BOOT_CMD(
+U_BOOT_CMD (
try_working, 1, 1, barcobcd_boot_image,
" try_working - check flash value and boot the appropriate image\n",
"\n"
);
-U_BOOT_CMD(
+U_BOOT_CMD (
boot_working, 1, 1, barcobcd_boot_image,
" boot_working - check flash value and boot the appropriate image\n",
"\n"
);
-U_BOOT_CMD(
+U_BOOT_CMD (
boot_default, 1, 1, barcobcd_boot_image,
" boot_default - check flash value and boot the appropriate image\n",
"\n"
/*
* We are not using serial communication, so just provide empty functions
*/
-int serial_init(void){return 0;}
-void serial_setbrg(void){}
-void serial_putc(const char c){}
-void serial_puts(const char *c){}
-void serial_addr(unsigned int i){}
-int serial_getc(void){return 0;}
-int serial_tstc(void){return 0;}
-
-unsigned long post_word_load(void){return 0l;};
-void post_word_store(unsigned long val){}
+int serial_init (void)
+{
+ return 0;
+}
+void serial_setbrg (void)
+{
+ return;
+}
+void serial_putc (const char c)
+{
+ return;
+}
+void serial_puts (const char *c)
+{
+ return;
+}
+void serial_addr (unsigned int i)
+{
+ return;
+}
+int serial_getc (void)
+{
+ return 0;
+}
+int serial_tstc (void)
+{
+ return 0;
+}
+
+unsigned long post_word_load (void)
+{
+ return 0l;
+}
+void post_word_store (unsigned long val)
+{
+ return;
+}
env_nand.o env_dataflash.o env_flash.o env_eeprom.o \
env_nvram.o env_nowhere.o \
exports.o \
- flash.o fpga.o \
+ flash.o fpga.o ft_build.o \
hush.o kgdb.o lcd.o lists.o lynxkdi.o \
memsize.o miiphybb.o miiphyutil.o \
s_record.o serial.o soft_i2c.o soft_spi.o spartan2.o spartan3.o \
#include <environment.h>
#include <asm/byteorder.h>
+#ifdef CONFIG_OF_FLAT_TREE
+#include <ft_build.h>
+#endif
+
/*cmd_boot.c*/
extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
}
#endif /* CONFIG_SILENT_CONSOLE */
+#ifdef CONFIG_OF_FLAT_TREE
+extern const unsigned char oftree_dtb[];
+extern const unsigned int oftree_dtb_len;
+#endif
+
#ifdef CONFIG_PPC
static void
do_bootm_linux (cmd_tbl_t *cmdtp, int flag,
bd_t *kbd;
void (*kernel)(bd_t *, ulong, ulong, ulong, ulong);
image_header_t *hdr = &header;
+#ifdef CONFIG_OF_FLAT_TREE
+ char *of_flat_tree;
+#endif
if ((s = getenv ("initrd_high")) != NULL) {
/* a value of "no" or a similar string will act like 0,
initrd_end = 0;
}
+#ifdef CONFIG_OF_FLAT_TREE
+ if (initrd_start == 0)
+ of_flat_tree = (char *)(((ulong)kbd - OF_FLAT_TREE_MAX_SIZE -
+ sizeof(bd_t)) & ~0xF);
+ else
+ of_flat_tree = (char *)((initrd_start - OF_FLAT_TREE_MAX_SIZE -
+ sizeof(bd_t)) & ~0xF);
+#endif
debug ("## Transferring control to Linux (at address %08lx) ...\n",
(ulong)kernel);
SHOW_BOOT_PROGRESS (15);
+#ifndef CONFIG_OF_FLAT_TREE
+
#if defined(CFG_INIT_RAM_LOCK) && !defined(CONFIG_E500)
unlock_ram_in_cache();
#endif
+
/*
* Linux Kernel Parameters:
* r3: ptr to board info data
* r7: End of command line string
*/
(*kernel) (kbd, initrd_start, initrd_end, cmd_start, cmd_end);
+
+#else
+ ft_setup(of_flat_tree, OF_FLAT_TREE_MAX_SIZE, kbd);
+ /* ft_dump_blob(of_flat_tree); */
+
+#if defined(CFG_INIT_RAM_LOCK) && !defined(CONFIG_E500)
+ unlock_ram_in_cache();
+#endif
+ /*
+ * Linux Kernel Parameters:
+ * r3: ptr to OF flat tree, followed by the board info data
+ * r4: initrd_start or 0 if no initrd
+ * r5: initrd_end - unused if r4 is 0
+ * r6: Start of command line string
+ * r7: End of command line string
+ */
+ (*kernel) ((bd_t *)of_flat_tree, initrd_start, initrd_end, cmd_start, cmd_end);
+
+#endif
}
#endif /* CONFIG_PPC */
do_iopset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
{
uint rcode = 0;
+ iopin_t iopin;
static uint port = 0;
static uint pin = 0;
static uint value = 0;
- static enum { DIR, PAR, SOR, ODR, DAT, INT } cmd = DAT;
- iopin_t iopin;
+ static enum {
+ DIR,
+ PAR,
+ SOR,
+ ODR,
+ DAT,
+#if defined(CONFIG_8xx)
+ INT
+#endif
+ } cmd = DAT;
if (argc != 5) {
puts ("iopset PORT PIN CMD VALUE\n");
/* Init Ehternet buffers */
for (i = 0; i < RBF_FRAMEMAX; i++) {
- rbfdt[i].addr = rbf_framebuf[i];
+ rbfdt[i].addr = (unsigned long)rbf_framebuf[i];
rbfdt[i].size = 0;
}
rbfdt[RBF_FRAMEMAX - 1].addr |= RBF_WRAP;
#undef DEBUG
-#define CONFIG_405 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_405 1 /* This is a PPC405 CPU */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_AP1000 1 /* ...on an AP1000 board */
+#define CONFIG_AP1000 1 /* ...on an AP1000 board */
-#define CONFIG_PCI 1
+#define CONFIG_PCI 1
-#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
-#define CFG_PROMPT "0> "
+#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
+#define CFG_PROMPT "0> "
#define CFG_PROMPT_HUSH_PS2 "> "
-#define CONFIG_COMMAND_EDIT 1
-#define CONFIG_COMMAND_HISTORY 1
+#define CONFIG_COMMAND_EDIT 1
+#define CONFIG_COMMAND_HISTORY 1
#define CONFIG_COMPLETE_ADDRESSES 1
#define CFG_ENV_IS_IN_FLASH 1
#endif
#endif
-#define CONFIG_BAUDRATE 57600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+#define CONFIG_BAUDRATE 57600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-#define CONFIG_BOOTCOMMAND "" /* autoboot command */
+#define CONFIG_BOOTCOMMAND "" /* autoboot command */
/* Size (bytes) of interrupt driven serial port buffer.
* Set to 0 to use polling instead of interrupts.
*/
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_BOOTARGS "console=ttyS0,57600"
+#define CONFIG_BOOTARGS "console=ttyS0,57600"
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_COMMANDS ( (CONFIG_CMD_DFL & \
- (~CFG_CMD_RTC) & ~(CFG_CMD_I2C)) | \
- CFG_CMD_IRQ | \
- CFG_CMD_PCI | \
- CFG_CMD_DHCP | \
- CFG_CMD_ASKENV | \
- CFG_CMD_ELF | \
- CFG_CMD_PING | \
- CFG_CMD_MVENV \
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_ELF | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_MVENV | \
+ CFG_CMD_PCI | \
+ CFG_CMD_PING \
)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SYS_CLK_FREQ 30000000
+#define CONFIG_SYS_CLK_FREQ 30000000
-#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
+#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LONGHELP /* undef to save memory */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* usually: (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) */
-#define CFG_PBSIZE (CFG_CBSIZE+4+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+4+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_ALT_MEMTEST 1
-#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x01000000 /* 4 ... 16 MB in DRAM */
+#define CFG_ALT_MEMTEST 1
+#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x01000000 /* 4 ... 16 MB in DRAM */
/*
* If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
* set Linux BASE_BAUD to 403200.
*/
-#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
-#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
-
-#define CFG_NS16550_CLK 40000000
-#define CFG_DUART_CHAN 0
-#define CFG_NS16550_COM1 (0x4C000000 + 0x1000)
-#define CFG_NS16550_COM2 (0x4C800000 + 0x1000)
-#define CFG_NS16550_REG_SIZE 4
-#define CFG_NS16550 1
-#define CFG_INIT_CHAN1 1
-#define CFG_INIT_CHAN2 0
+#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
+#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
+
+#define CFG_NS16550_CLK 40000000
+#define CFG_DUART_CHAN 0
+#define CFG_NS16550_COM1 (0x4C000000 + 0x1000)
+#define CFG_NS16550_COM2 (0x4C800000 + 0x1000)
+#define CFG_NS16550_REG_SIZE 4
+#define CFG_NS16550 1
+#define CFG_INIT_CHAN1 1
+#define CFG_INIT_CHAN2 0
/* The following table includes the supported baudrates */
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-#define CFG_LOAD_ADDR 0x00100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CFG_LOAD_ADDR 0x00200000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0x20000000
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x20000000
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_FLASH_CFI 1
-#define CFG_PROGFLASH_BASE CFG_FLASH_BASE
-#define CFG_CONFFLASH_BASE 0x24000000
+#define CFG_FLASH_CFI 1
+#define CFG_PROGFLASH_BASE CFG_FLASH_BASE
+#define CFG_CONFFLASH_BASE 0x24000000
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_PROTECTION 1 /* use hardware protection */
+#define CFG_FLASH_PROTECTION 1 /* use hardware protection */
/* BEG ENVIRONNEMENT FLASH */
#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */
-#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-#define CFG_ENV_SECT_SIZE 0x20000 /* see README - env sector total size */
+#define CFG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE 0x20000 /* see README - env sector total size */
#endif
/* END ENVIRONNEMENT FLASH */
/*-----------------------------------------------------------------------
* NVRAM organization
*/
-#define CFG_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 0x1ff8 /* NVRAM size */
+#define CFG_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
+#define CFG_NVRAM_SIZE 0x1ff8 /* NVRAM size */
#ifdef CFG_ENV_IS_IN_NVRAM
-#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */
+#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */
#define CFG_ENV_ADDR \
(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_DCACHE_SIZE 16384
-#define CFG_CACHELINE_SIZE 32
+#define CFG_DCACHE_SIZE 16384
+#define CFG_CACHELINE_SIZE 32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* BR0/1 and OR0/1 (FLASH)
*/
-#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
+#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
/* Configuration Port location */
-#define CONFIG_PORT_ADDR 0xF0000500
+#define CONFIG_PORT_ADDR 0xF0000500
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
#define CFG_INIT_RAM_ADDR 0x400000 /* inside of SDRAM */
#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
*
* Boot Flags
*/
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/* JFFS2 stuff */
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS 1
-#define CFG_JFFS2_FIRST_SECTOR 1
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_NUM_BANKS 1
+#define CFG_JFFS2_FIRST_SECTOR 1
#define CONFIG_NET_MULTI
#define CONFIG_E1000
-#define CFG_ETH_DEV_FN 0x0800
-#define CFG_ETH_IOBASE 0x31000000
-#define CFG_ETH_MEMBASE 0x32000000
+#define CFG_ETH_DEV_FN 0x0800
+#define CFG_ETH_IOBASE 0x31000000
+#define CFG_ETH_MEMBASE 0x32000000
#endif /* __CONFIG_H */
#define SCL 0x1000 /* PA 3 */
#define SDA 0x2000 /* PA 2 */
-#define PAR immr->im_ioport.iop_papar
-#define DIR immr->im_ioport.iop_padir
-#define DAT immr->im_ioport.iop_padat
-
-#define I2C_INIT {PAR &= ~(SCL | SDA); DIR |= SCL;}
-#define I2C_ACTIVE (DIR |= SDA)
-#define I2C_TRISTATE (DIR &= ~SDA)
-#define I2C_READ ((DAT & SDA) != 0)
-#define I2C_SDA(bit) if (bit) DAT |= SDA; \
- else DAT &= ~SDA
-#define I2C_SCL(bit) if (bit) DAT |= SCL; \
- else DAT &= ~SCL
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+#define __I2C_DIR immr->im_ioport.iop_padir
+#define __I2C_DAT immr->im_ioport.iop_padat
+#define __I2C_PAR immr->im_ioport.iop_papar
+#define I2C_INIT { __I2C_PAR &= ~(SDA|SCL); \
+ __I2C_DIR |= (SDA|SCL); }
+#define I2C_READ ((__I2C_DAT & SDA) ? 1 : 0)
+#define I2C_SDA(x) { if (x) __I2C_DAT |= SDA; else __I2C_DAT &= ~SDA; }
+#define I2C_SCL(x) { if (x) __I2C_DAT |= SCL; else __I2C_DAT &= ~SCL; }
+#define I2C_DELAY { udelay(5); }
+#define I2C_ACTIVE { __I2C_DIR |= SDA; }
+#define I2C_TRISTATE { __I2C_DIR &= ~SDA; }
#define CONFIG_RTC_PCF8563
#define CFG_I2C_RTC_ADDR 0x51
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_EEPRO100
+/* #define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */
#define CONFIG_E1000
#undef CONFIG_TULIP
#if defined (CONFIG_SOFT_I2C)
#define SDA 0x00010
#define SCL 0x00020
-#define DIR immr->im_cpm.cp_pbdir
-#define DAT immr->im_cpm.cp_pbdat
-#define PAR immr->im_cpm.cp_pbpar
-#define ODR immr->im_cpm.cp_pbodr
-#define I2C_INIT {PAR&=~(SDA|SCL);ODR&=~(SDA|SCL);DAT|=(SDA|SCL);DIR|=(SDA|SCL);}
-#define I2C_READ ((DAT&SDA)?1:0)
-#define I2C_SDA(x) {if(x)DAT|=SDA;else DAT&=~SDA;}
-#define I2C_SCL(x) {if(x)DAT|=SCL;else DAT&=~SCL;}
-#define I2C_DELAY {udelay(5);}
-#define I2C_ACTIVE {DIR|=SDA;}
-#define I2C_TRISTATE {DIR&=~SDA;}
+#define __I2C_DIR immr->im_cpm.cp_pbdir
+#define __I2C_DAT immr->im_cpm.cp_pbdat
+#define __I2C_PAR immr->im_cpm.cp_pbpar
+#define __I2C_ODR immr->im_cpm.cp_pbodr
+#define I2C_INIT { __I2C_PAR &= ~(SDA|SCL); \
+ __I2C_ODR &= ~(SDA|SCL); \
+ __I2C_DAT |= (SDA|SCL); \
+ __I2C_DIR|=(SDA|SCL); }
+#define I2C_READ ((__I2C_DAT & SDA) ? 1 : 0)
+#define I2C_SDA(x) { if (x) __I2C_DAT |= SDA; else __I2C_DAT &= ~SDA; }
+#define I2C_SCL(x) { if (x) __I2C_DAT |= SCL; else __I2C_DAT &= ~SCL; }
+#define I2C_DELAY { udelay(5); }
+#define I2C_ACTIVE { __I2C_DIR |= SDA; }
+#define I2C_TRISTATE { __I2C_DIR &= ~SDA; }
#endif
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#define CONFIG_PCI_IO_SIZE 0x01000000
#define CONFIG_NET_MULTI 1
-#define CONFIG_EEPRO100 1
+/* #define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
#endif /* CONFIG_STK52XX */
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_EEPRO100
+/* #define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */
#undef CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_OFFSET 0x000047A4 /* Offset of Environment Sector */
#define CFG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */
-#define ENV_CRC 0x8BF6F24B
+/* #define ENV_CRC 0x8BF6F24B XXX - FIXME: gets defined automatically */
#define CFG_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */
#define CFG_XLB_PIPELINING 1
#define CONFIG_NET_MULTI 1
-#define CONFIG_EEPRO100 1
+/* #define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
projects / u-boot.git / commitdiff