LIB = $(obj)lib$(BOARD).a
-COBJS := eNET.o
-SOBJS := eNET_start16.o eNET_start.o
+COBJS-y += eNET.o
+SOBJS-y += eNET_start16.o
+SOBJS-y += eNET_start.o
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
+SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y))
$(LIB): $(obj).depend $(OBJS) $(SOBJS)
$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
LIB = $(obj)lib$(BOARD).a
-COBJS := sc520_cdp.o flash.o
-SOBJS := sc520_cdp_asm.o sc520_cdp_asm16.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
+COBJS-y += sc520_cdp.o
+COBJS-y += flash.o
+COBJS-$(CONFIG_PCI) += sc520_cdp_pci.o
+SOBJS-y += sc520_cdp_asm.o
+SOBJS-y += sc520_cdp_asm16.o
+
+SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y))
$(LIB): $(obj).depend $(OBJS) $(SOBJS)
$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
*/
#include <common.h>
-#include <pci.h>
#include <asm/io.h>
-#include <asm/pci.h>
#include <asm/ic/sc520.h>
-#include <asm/ic/pci.h>
#include <ali512x.h>
#include <spi.h>
#include <netdev.h>
sc520_mmcr->eccmap = 0x100; /* Map SDRAM ECC failure INT to NMI */
}
-#ifdef CONFIG_PCI
-/* PCI stuff */
-static void pci_sc520_cdp_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
-{
- /* a configurable lists of irqs to steal
- * when we need one (a board with more pci interrupt pins
- * would use a larger table */
- static int irq_list[] = {
- CONFIG_SYS_FIRST_PCI_IRQ,
- CONFIG_SYS_SECOND_PCI_IRQ,
- CONFIG_SYS_THIRD_PCI_IRQ,
- CONFIG_SYS_FORTH_PCI_IRQ
- };
- static int next_irq_index=0;
-
- uchar tmp_pin;
- int pin;
-
- pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &tmp_pin);
- pin = tmp_pin;
-
- pin-=1; /* pci config space use 1-based numbering */
- if (-1 == pin) {
- return; /* device use no irq */
- }
-
-
- /* map device number + pin to a pin on the sc520 */
- switch (PCI_DEV(dev)) {
- case 20:
- pin+=SC520_PCI_INTA;
- break;
-
- case 19:
- pin+=SC520_PCI_INTB;
- break;
-
- case 18:
- pin+=SC520_PCI_INTC;
- break;
-
- case 17:
- pin+=SC520_PCI_INTD;
- break;
-
- default:
- return;
- }
-
- pin&=3; /* wrap around */
-
- if (sc520_pci_ints[pin] == -1) {
- /* re-route one interrupt for us */
- if (next_irq_index > 3) {
- return;
- }
- if (pci_sc520_set_irq(pin, irq_list[next_irq_index])) {
- return;
- }
- next_irq_index++;
- }
-
-
- if (-1 != sc520_pci_ints[pin]) {
- pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE,
- sc520_pci_ints[pin]);
- }
- PRINTF("fixup_irq: device %d pin %c irq %d\n",
- PCI_DEV(dev), 'A' + pin, sc520_pci_ints[pin]);
-}
-
-static struct pci_controller sc520_cdp_hose = {
- fixup_irq: pci_sc520_cdp_fixup_irq,
-};
-
-void pci_init_board(void)
-{
- pci_sc520_init(&sc520_cdp_hose);
-}
-#endif
-
static void silence_uart(int port)
{
outb(0, port+1);
* PAR15 Port 0x680 LED display
*/
-/*
- * This function should map a chunk of size bytes
- * of the system address space to the ISA bus
- *
- * The function will return the memory address
- * as seen by the host (which may very will be the
- * same as the bus address)
- */
-u32 isa_map_rom(u32 bus_addr, int size)
-{
- u32 par;
-
- PRINTF("isa_map_rom asked to map %d bytes at %x\n",
- size, bus_addr);
-
- par = size;
- if (par < 0x80000) {
- par = 0x80000;
- }
- par >>= 12;
- par--;
- par&=0x7f;
- par <<= 18;
- par |= (bus_addr>>12);
- par |= 0x50000000;
-
- PRINTF ("setting PAR11 to %x\n", par);
-
- /* Map rom 0x10000 with PAR1 */
- sc520_mmcr->par[11] = par;
-
- return bus_addr;
-}
-
-/*
- * this function removed any mapping created
- * with pci_get_rom_window()
- */
-void isa_unmap_rom(u32 addr)
-{
- PRINTF("isa_unmap_rom asked to unmap %x", addr);
- if ((addr>>12) == (sc520_mmcr->par[11] & 0x3ffff)) {
- sc520_mmcr->par[11] = 0;
- PRINTF(" done\n");
- return;
- }
- PRINTF(" not ours\n");
-}
-
-#ifdef CONFIG_PCI
-#define PCI_ROM_TEMP_SPACE 0x10000
-/*
- * This function should map a chunk of size bytes
- * of the system address space to the PCI bus,
- * suitable to map PCI ROMS (bus address < 16M)
- * the function will return the host memory address
- * which should be converted into a bus address
- * before used to configure the PCI rom address
- * decoder
- */
-u32 pci_get_rom_window(struct pci_controller *hose, int size)
-{
- u32 par;
-
- par = size;
- if (par < 0x80000) {
- par = 0x80000;
- }
- par >>= 16;
- par--;
- par&=0x7ff;
- par <<= 14;
- par |= (PCI_ROM_TEMP_SPACE>>16);
- par |= 0x72000000;
-
- PRINTF ("setting PAR1 to %x\n", par);
-
- /* Map rom 0x10000 with PAR1 */
- sc520_mmcr->par[1] = par;
-
- return PCI_ROM_TEMP_SPACE;
-}
-
-/*
- * this function removed any mapping created
- * with pci_get_rom_window()
- */
-void pci_remove_rom_window(struct pci_controller *hose, u32 addr)
-{
- PRINTF("pci_remove_rom_window: %x", addr);
- if (addr == PCI_ROM_TEMP_SPACE) {
- sc520_mmcr->par[1] = 0;
- PRINTF(" done\n");
- return;
- }
- PRINTF(" not ours\n");
-
-}
-
-/*
- * This function is called in order to provide acces to the
- * legacy video I/O ports on the PCI bus.
- * After this function accesses to I/O ports 0x3b0-0x3bb and
- * 0x3c0-0x3df shuld result in transactions on the PCI bus.
- *
- */
-int pci_enable_legacy_video_ports(struct pci_controller *hose)
-{
- /* Map video memory to 0xa0000*/
- sc520_mmcr->par[0] = 0x7200400a;
-
- /* forward all I/O accesses to PCI */
- sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | IO_HOLE_DEST_PCI;
-
-
- /* so we map away all io ports to pci (only way to access pci io
- * below 0x400. But then we have to map back the portions that we dont
- * use so that the generate cycles on the GPIO bus where the sio and
- * ISA slots are connected, this requre the use of several PAR registers
- */
-
- /* bring 0x100 - 0x1ef back to ISA using PAR5 */
- sc520_mmcr->par[5] = 0x30ef0100;
-
- /* IDE use 1f0-1f7 */
-
- /* bring 0x1f8 - 0x2f7 back to ISA using PAR6 */
- sc520_mmcr->par[6] = 0x30ff01f8;
-
- /* com2 use 2f8-2ff */
-
- /* bring 0x300 - 0x3af back to ISA using PAR7 */
- sc520_mmcr->par[7] = 0x30af0300;
-
- /* vga use 3b0-3bb */
-
- /* bring 0x3bc - 0x3bf back to ISA using PAR8 */
- sc520_mmcr->par[8] = 0x300303bc;
-
- /* vga use 3c0-3df */
-
- /* bring 0x3e0 - 0x3f5 back to ISA using PAR9 */
- sc520_mmcr->par[9] = 0x301503e0;
-
- /* ide use 3f6 */
-
- /* bring 0x3f7 back to ISA using PAR10 */
- sc520_mmcr->par[10] = 0x300003f7;
-
- /* com1 use 3f8-3ff */
-
- return 0;
-}
-#endif
-
/*
* Miscelaneous platform dependent initialisations
*/
--- /dev/null
+/*
+ *
+ * (C) Copyright 2002
+ * Daniel Engström, Omicron Ceti AB <daniel@omicron.se>.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <asm/io.h>
+#include <asm/pci.h>
+#include <asm/ic/sc520.h>
+#include <asm/ic/pci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#undef SC520_CDP_DEBUG
+
+#ifdef SC520_CDP_DEBUG
+#define PRINTF(fmt,args...) printf (fmt ,##args)
+#else
+#define PRINTF(fmt,args...)
+#endif
+
+static void pci_sc520_cdp_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+{
+ /* a configurable lists of irqs to steal
+ * when we need one (a board with more pci interrupt pins
+ * would use a larger table */
+ static int irq_list[] = {
+ CONFIG_SYS_FIRST_PCI_IRQ,
+ CONFIG_SYS_SECOND_PCI_IRQ,
+ CONFIG_SYS_THIRD_PCI_IRQ,
+ CONFIG_SYS_FORTH_PCI_IRQ
+ };
+ static int next_irq_index=0;
+
+ uchar tmp_pin;
+ int pin;
+
+ pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &tmp_pin);
+ pin = tmp_pin;
+
+ pin-=1; /* pci config space use 1-based numbering */
+ if (-1 == pin) {
+ return; /* device use no irq */
+ }
+
+
+ /* map device number + pin to a pin on the sc520 */
+ switch (PCI_DEV(dev)) {
+ case 20:
+ pin+=SC520_PCI_INTA;
+ break;
+
+ case 19:
+ pin+=SC520_PCI_INTB;
+ break;
+
+ case 18:
+ pin+=SC520_PCI_INTC;
+ break;
+
+ case 17:
+ pin+=SC520_PCI_INTD;
+ break;
+
+ default:
+ return;
+ }
+
+ pin&=3; /* wrap around */
+
+ if (sc520_pci_ints[pin] == -1) {
+ /* re-route one interrupt for us */
+ if (next_irq_index > 3) {
+ return;
+ }
+ if (pci_sc520_set_irq(pin, irq_list[next_irq_index])) {
+ return;
+ }
+ next_irq_index++;
+ }
+
+
+ if (-1 != sc520_pci_ints[pin]) {
+ pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE,
+ sc520_pci_ints[pin]);
+ }
+ PRINTF("fixup_irq: device %d pin %c irq %d\n",
+ PCI_DEV(dev), 'A' + pin, sc520_pci_ints[pin]);
+}
+
+static struct pci_controller sc520_cdp_hose = {
+ fixup_irq: pci_sc520_cdp_fixup_irq,
+};
+
+void pci_init_board(void)
+{
+ pci_sc520_init(&sc520_cdp_hose);
+}
+
+/*
+ * This function should map a chunk of size bytes
+ * of the system address space to the ISA bus
+ *
+ * The function will return the memory address
+ * as seen by the host (which may very will be the
+ * same as the bus address)
+ */
+u32 isa_map_rom(u32 bus_addr, int size)
+{
+ u32 par;
+
+ PRINTF("isa_map_rom asked to map %d bytes at %x\n",
+ size, bus_addr);
+
+ par = size;
+ if (par < 0x80000) {
+ par = 0x80000;
+ }
+ par >>= 12;
+ par--;
+ par&=0x7f;
+ par <<= 18;
+ par |= (bus_addr>>12);
+ par |= 0x50000000;
+
+ PRINTF ("setting PAR11 to %x\n", par);
+
+ /* Map rom 0x10000 with PAR1 */
+ sc520_mmcr->par[11] = par;
+
+ return bus_addr;
+}
+
+/*
+ * this function removed any mapping created
+ * with pci_get_rom_window()
+ */
+void isa_unmap_rom(u32 addr)
+{
+ PRINTF("isa_unmap_rom asked to unmap %x", addr);
+ if ((addr>>12) == (sc520_mmcr->par[11] & 0x3ffff)) {
+ sc520_mmcr->par[11] = 0;
+ PRINTF(" done\n");
+ return;
+ }
+ PRINTF(" not ours\n");
+}
+
+#define PCI_ROM_TEMP_SPACE 0x10000
+/*
+ * This function should map a chunk of size bytes
+ * of the system address space to the PCI bus,
+ * suitable to map PCI ROMS (bus address < 16M)
+ * the function will return the host memory address
+ * which should be converted into a bus address
+ * before used to configure the PCI rom address
+ * decoder
+ */
+u32 pci_get_rom_window(struct pci_controller *hose, int size)
+{
+ u32 par;
+
+ par = size;
+ if (par < 0x80000) {
+ par = 0x80000;
+ }
+ par >>= 16;
+ par--;
+ par&=0x7ff;
+ par <<= 14;
+ par |= (PCI_ROM_TEMP_SPACE>>16);
+ par |= 0x72000000;
+
+ PRINTF ("setting PAR1 to %x\n", par);
+
+ /* Map rom 0x10000 with PAR1 */
+ sc520_mmcr->par[1] = par;
+
+ return PCI_ROM_TEMP_SPACE;
+}
+
+/*
+ * this function removed any mapping created
+ * with pci_get_rom_window()
+ */
+void pci_remove_rom_window(struct pci_controller *hose, u32 addr)
+{
+ PRINTF("pci_remove_rom_window: %x", addr);
+ if (addr == PCI_ROM_TEMP_SPACE) {
+ sc520_mmcr->par[1] = 0;
+ PRINTF(" done\n");
+ return;
+ }
+ PRINTF(" not ours\n");
+
+}
+
+/*
+ * This function is called in order to provide acces to the
+ * legacy video I/O ports on the PCI bus.
+ * After this function accesses to I/O ports 0x3b0-0x3bb and
+ * 0x3c0-0x3df shuld result in transactions on the PCI bus.
+ *
+ */
+int pci_enable_legacy_video_ports(struct pci_controller *hose)
+{
+ /* Map video memory to 0xa0000*/
+ sc520_mmcr->par[0] = 0x7200400a;
+
+ /* forward all I/O accesses to PCI */
+ sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | IO_HOLE_DEST_PCI;
+
+
+ /* so we map away all io ports to pci (only way to access pci io
+ * below 0x400. But then we have to map back the portions that we dont
+ * use so that the generate cycles on the GPIO bus where the sio and
+ * ISA slots are connected, this requre the use of several PAR registers
+ */
+
+ /* bring 0x100 - 0x1ef back to ISA using PAR5 */
+ sc520_mmcr->par[5] = 0x30ef0100;
+
+ /* IDE use 1f0-1f7 */
+
+ /* bring 0x1f8 - 0x2f7 back to ISA using PAR6 */
+ sc520_mmcr->par[6] = 0x30ff01f8;
+
+ /* com2 use 2f8-2ff */
+
+ /* bring 0x300 - 0x3af back to ISA using PAR7 */
+ sc520_mmcr->par[7] = 0x30af0300;
+
+ /* vga use 3b0-3bb */
+
+ /* bring 0x3bc - 0x3bf back to ISA using PAR8 */
+ sc520_mmcr->par[8] = 0x300303bc;
+
+ /* vga use 3c0-3df */
+
+ /* bring 0x3e0 - 0x3f5 back to ISA using PAR9 */
+ sc520_mmcr->par[9] = 0x301503e0;
+
+ /* ide use 3f6 */
+
+ /* bring 0x3f7 back to ISA using PAR10 */
+ sc520_mmcr->par[10] = 0x300003f7;
+
+ /* com1 use 3f8-3ff */
+
+ return 0;
+}
LIB = $(obj)lib$(BOARD).a
-COBJS := sc520_spunk.o flash.o
-SOBJS := sc520_spunk_asm.o sc520_spunk_asm16.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
+COBJS-y += sc520_spunk.o
+COBJS-y += flash.o
+COBJS-$(CONFIG_PCI) += sc520_spunk_pci.o
+SOBJS-y += sc520_spunk_asm.o
+SOBJS-y += sc520_spunk_asm16.o
+
+SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y))
$(LIB): $(obj).depend $(OBJS) $(SOBJS)
$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
*/
#include <common.h>
-#include <pci.h>
#include <netdev.h>
#include <ds1722.h>
#include <asm/io.h>
-#include <asm/pci.h>
#include <asm/ic/sc520.h>
-#include <asm/ic/pci.h>
#include <asm/ic/ssi.h>
DECLARE_GLOBAL_DATA_PTR;
}
-
-/* PCI stuff */
-static void pci_sc520_spunk_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
-{
- int version = sc520_mmcr->sysinfo;
-
- /* a configurable lists of irqs to steal
- * when we need one (a board with more pci interrupt pins
- * would use a larger table */
- static int irq_list[] = {
- CONFIG_SYS_FIRST_PCI_IRQ,
- CONFIG_SYS_SECOND_PCI_IRQ,
- CONFIG_SYS_THIRD_PCI_IRQ,
- CONFIG_SYS_FORTH_PCI_IRQ
- };
- static int next_irq_index=0;
-
- uchar tmp_pin;
- int pin;
-
- pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &tmp_pin);
- pin = tmp_pin;
-
- pin-=1; /* pci config space use 1-based numbering */
- if (-1 == pin) {
- return; /* device use no irq */
- }
-
-
- /* map device number + pin to a pin on the sc520 */
- switch (PCI_DEV(dev)) {
- case 6: /* ETH0 */
- pin+=SC520_PCI_INTA;
- break;
-
- case 7: /* ETH1 */
- pin+=SC520_PCI_INTB;
- break;
-
- case 8: /* Crypto */
- pin+=SC520_PCI_INTC;
- break;
-
- case 9: /* PMC slot */
- pin+=SC520_PCI_INTD;
- break;
-
- case 10: /* PC-Card */
-
- if (version < 10) {
- pin+=SC520_PCI_INTD;
- } else {
- pin+=SC520_PCI_INTC;
- }
- break;
-
- default:
- return;
- }
-
- pin&=3; /* wrap around */
-
- if (sc520_pci_ints[pin] == -1) {
- /* re-route one interrupt for us */
- if (next_irq_index > 3) {
- return;
- }
- if (pci_sc520_set_irq(pin, irq_list[next_irq_index])) {
- return;
- }
- next_irq_index++;
- }
-
-
- if (-1 != sc520_pci_ints[pin]) {
- pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE,
- sc520_pci_ints[pin]);
- }
-#if 0
- printf("fixup_irq: device %d pin %c irq %d\n",
- PCI_DEV(dev), 'A' + pin, sc520_pci_ints[pin]);
-#endif
-}
-
-
-static void pci_sc520_spunk_configure_cardbus(struct pci_controller *hose,
- pci_dev_t dev, struct pci_config_table *te)
-{
- u32 io_base;
- u32 temp;
-
- pciauto_config_device(hose, dev);
-
- pci_hose_write_config_word(hose, dev, PCI_COMMAND, 0x07); /* enable device */
- pci_hose_write_config_byte(hose, dev, 0x0c, 0x10); /* cacheline size */
- pci_hose_write_config_byte(hose, dev, 0x0d, 0x40); /* latency timer */
- pci_hose_write_config_byte(hose, dev, 0x1b, 0x40); /* cardbus latency timer */
- pci_hose_write_config_word(hose, dev, PCI_BRIDGE_CONTROL, 0x0040); /* reset cardbus */
- pci_hose_write_config_word(hose, dev, PCI_BRIDGE_CONTROL, 0x0080); /* route interrupts though ExCA */
- pci_hose_write_config_word(hose, dev, 0x44, 0x3e0); /* map legacy I/O port to 0x3e0 */
-
- pci_hose_read_config_dword(hose, dev, 0x80, &temp); /* System control */
- pci_hose_write_config_dword(hose, dev, 0x80, temp | 0x60); /* System control: disable clockrun */
- /* route MF0 to ~INT and MF3 to IRQ7
- * reserve all others */
- pci_hose_write_config_dword(hose, dev, 0x8c, 0x00007002);
- pci_hose_write_config_byte(hose, dev, 0x91, 0x00); /* card control */
- pci_hose_write_config_byte(hose, dev, 0x92, 0x62); /* device control */
-
- if (te->device != 0xac56) {
- pci_hose_write_config_byte(hose, dev, 0x93, 0x21); /* async interrupt enable */
- pci_hose_write_config_word(hose, dev, 0xa8, 0x0000); /* reset GPIO */
- pci_hose_write_config_word(hose, dev, 0xac, 0x0000); /* reset GPIO */
- pci_hose_write_config_word(hose, dev, 0xaa, 0x0000); /* reset GPIO */
- pci_hose_write_config_word(hose, dev, 0xae, 0x0000); /* reset GPIO */
- } else {
- pci_hose_write_config_byte(hose, dev, 0x93, 0x20); /* */
- }
- pci_hose_write_config_word(hose, dev, 0xa4, 0x8000); /* reset power management */
-
-
- pci_hose_read_config_dword(hose, dev, PCI_BASE_ADDRESS_0, &io_base);
- io_base &= ~0xfL;
-
- writeb(0x07, io_base+0x803); /* route CSC irq though ExCA and enable IRQ7 */
- writel(0, io_base+0x10); /* CLKRUN default */
- writel(0, io_base+0x20); /* CLKRUN default */
-
-}
-
-
-static struct pci_config_table pci_sc520_spunk_config_table[] = {
- { 0x104c, 0xac50, PCI_ANY_ID, 0, 0x0a, 0, pci_sc520_spunk_configure_cardbus, { 0, 0, 0} },
- { 0x104c, 0xac56, PCI_ANY_ID, 0, 0x0a, 0, pci_sc520_spunk_configure_cardbus, { 0, 0, 0} },
- { 0, 0, 0, 0, 0, 0, NULL, {0,0,0}}
-};
-
-static struct pci_controller sc520_spunk_hose = {
- fixup_irq: pci_sc520_spunk_fixup_irq,
- config_table: pci_sc520_spunk_config_table,
- first_busno: 0x00,
- last_busno: 0xff,
-};
-
-void pci_init_board(void)
-{
- pci_sc520_init(&sc520_spunk_hose);
-}
-
-
/* set up the ISA bus timing and system address mappings */
static void bus_init(void)
{
* PAR15
*/
-/*
- * This function should map a chunk of size bytes
- * of the system address space to the ISA bus
- *
- * The function will return the memory address
- * as seen by the host (which may very will be the
- * same as the bus address)
- */
-u32 isa_map_rom(u32 bus_addr, int size)
-{
- u32 par;
-
- printf("isa_map_rom asked to map %d bytes at %x\n",
- size, bus_addr);
-
- par = size;
- if (par < 0x80000) {
- par = 0x80000;
- }
- par >>= 12;
- par--;
- par&=0x7f;
- par <<= 18;
- par |= (bus_addr>>12);
- par |= 0x50000000;
-
- printf ("setting PAR11 to %x\n", par);
-
- /* Map rom 0x10000 with PAR1 */
- sc520_mmcr->par[11] = par;
-
- return bus_addr;
-}
-
-/*
- * this function removed any mapping created
- * with pci_get_rom_window()
- */
-void isa_unmap_rom(u32 addr)
-{
- printf("isa_unmap_rom asked to unmap %x", addr);
- if ((addr>>12) == (sc520_mmcr->par[11] & 0x3ffff)) {
- sc520_mmcr->par[11] = 0;
- printf(" done\n");
- return;
- }
- printf(" not ours\n");
-}
-
-#ifdef CONFIG_PCI
-#define PCI_ROM_TEMP_SPACE 0x10000
-/*
- * This function should map a chunk of size bytes
- * of the system address space to the PCI bus,
- * suitable to map PCI ROMS (bus address < 16M)
- * the function will return the host memory address
- * which should be converted into a bus address
- * before used to configure the PCI rom address
- * decoder
- */
-u32 pci_get_rom_window(struct pci_controller *hose, int size)
-{
- u32 par;
-
- par = size;
- if (par < 0x80000) {
- par = 0x80000;
- }
- par >>= 16;
- par--;
- par&=0x7ff;
- par <<= 14;
- par |= (PCI_ROM_TEMP_SPACE>>16);
- par |= 0x72000000;
-
- printf ("setting PAR1 to %x\n", par);
-
- /* Map rom 0x10000 with PAR1 */
- sc520_mmcr->par[1] = par;
-
- return PCI_ROM_TEMP_SPACE;
-}
-
-/*
- * this function removed any mapping created
- * with pci_get_rom_window()
- */
-void pci_remove_rom_window(struct pci_controller *hose, u32 addr)
-{
- printf("pci_remove_rom_window: %x", addr);
- if (addr == PCI_ROM_TEMP_SPACE) {
- sc520_mmcr->par[1] = 0;
- printf(" done\n");
- return;
- }
- printf(" not ours\n");
-
-}
-
-/*
- * This function is called in order to provide acces to the
- * legacy video I/O ports on the PCI bus.
- * After this function accesses to I/O ports 0x3b0-0x3bb and
- * 0x3c0-0x3df shuld result in transactions on the PCI bus.
- *
- */
-int pci_enable_legacy_video_ports(struct pci_controller *hose)
-{
- /* Map video memory to 0xa0000*/
- sc520_mmcr->par[0] = 0x7200400a;
-
- /* forward all I/O accesses to PCI */
- sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | IO_HOLE_DEST_PCI;
-
-
- /* so we map away all io ports to pci (only way to access pci io
- * below 0x400. But then we have to map back the portions that we dont
- * use so that the generate cycles on the GPIO bus where the sio and
- * ISA slots are connected, this requre the use of several PAR registers
- */
-
- /* bring 0x100 - 0x2f7 back to ISA using PAR5 */
- sc520_mmcr->par[5] = 0x31f70100;
-
- /* com2 use 2f8-2ff */
-
- /* bring 0x300 - 0x3af back to ISA using PAR7 */
- sc520_mmcr->par[7] = 0x30af0300;
-
- /* vga use 3b0-3bb */
-
- /* bring 0x3bc - 0x3bf back to ISA using PAR8 */
- sc520_mmcr->par[8] = 0x300303bc;
-
- /* vga use 3c0-3df */
-
- /* bring 0x3e0 - 0x3f7 back to ISA using PAR9 */
- sc520_mmcr->par[9] = 0x301703e0;
-
- /* com1 use 3f8-3ff */
-
- return 0;
-}
-#endif
-
/*
* Miscelaneous platform dependent initialisations
*/
--- /dev/null
+/*
+ *
+ * (C) Copyright 2002
+ * Daniel Engström, Omicron Ceti AB <daniel@omicron.se>.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <ds1722.h>
+#include <asm/io.h>
+#include <asm/pci.h>
+#include <asm/ic/sc520.h>
+#include <asm/ic/pci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void pci_sc520_spunk_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+{
+ int version = sc520_mmcr->sysinfo;
+
+ /* a configurable lists of irqs to steal
+ * when we need one (a board with more pci interrupt pins
+ * would use a larger table */
+ static int irq_list[] = {
+ CONFIG_SYS_FIRST_PCI_IRQ,
+ CONFIG_SYS_SECOND_PCI_IRQ,
+ CONFIG_SYS_THIRD_PCI_IRQ,
+ CONFIG_SYS_FORTH_PCI_IRQ
+ };
+ static int next_irq_index=0;
+
+ uchar tmp_pin;
+ int pin;
+
+ pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &tmp_pin);
+ pin = tmp_pin;
+
+ pin-=1; /* pci config space use 1-based numbering */
+ if (-1 == pin) {
+ return; /* device use no irq */
+ }
+
+
+ /* map device number + pin to a pin on the sc520 */
+ switch (PCI_DEV(dev)) {
+ case 6: /* ETH0 */
+ pin+=SC520_PCI_INTA;
+ break;
+
+ case 7: /* ETH1 */
+ pin+=SC520_PCI_INTB;
+ break;
+
+ case 8: /* Crypto */
+ pin+=SC520_PCI_INTC;
+ break;
+
+ case 9: /* PMC slot */
+ pin+=SC520_PCI_INTD;
+ break;
+
+ case 10: /* PC-Card */
+
+ if (version < 10) {
+ pin+=SC520_PCI_INTD;
+ } else {
+ pin+=SC520_PCI_INTC;
+ }
+ break;
+
+ default:
+ return;
+ }
+
+ pin&=3; /* wrap around */
+
+ if (sc520_pci_ints[pin] == -1) {
+ /* re-route one interrupt for us */
+ if (next_irq_index > 3) {
+ return;
+ }
+ if (pci_sc520_set_irq(pin, irq_list[next_irq_index])) {
+ return;
+ }
+ next_irq_index++;
+ }
+
+
+ if (-1 != sc520_pci_ints[pin]) {
+ pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE,
+ sc520_pci_ints[pin]);
+ }
+#if 0
+ printf("fixup_irq: device %d pin %c irq %d\n",
+ PCI_DEV(dev), 'A' + pin, sc520_pci_ints[pin]);
+#endif
+}
+
+
+static void pci_sc520_spunk_configure_cardbus(struct pci_controller *hose,
+ pci_dev_t dev, struct pci_config_table *te)
+{
+ u32 io_base;
+ u32 temp;
+
+ pciauto_config_device(hose, dev);
+
+ pci_hose_write_config_word(hose, dev, PCI_COMMAND, 0x07); /* enable device */
+ pci_hose_write_config_byte(hose, dev, 0x0c, 0x10); /* cacheline size */
+ pci_hose_write_config_byte(hose, dev, 0x0d, 0x40); /* latency timer */
+ pci_hose_write_config_byte(hose, dev, 0x1b, 0x40); /* cardbus latency timer */
+ pci_hose_write_config_word(hose, dev, PCI_BRIDGE_CONTROL, 0x0040); /* reset cardbus */
+ pci_hose_write_config_word(hose, dev, PCI_BRIDGE_CONTROL, 0x0080); /* route interrupts though ExCA */
+ pci_hose_write_config_word(hose, dev, 0x44, 0x3e0); /* map legacy I/O port to 0x3e0 */
+
+ pci_hose_read_config_dword(hose, dev, 0x80, &temp); /* System control */
+ pci_hose_write_config_dword(hose, dev, 0x80, temp | 0x60); /* System control: disable clockrun */
+ /* route MF0 to ~INT and MF3 to IRQ7
+ * reserve all others */
+ pci_hose_write_config_dword(hose, dev, 0x8c, 0x00007002);
+ pci_hose_write_config_byte(hose, dev, 0x91, 0x00); /* card control */
+ pci_hose_write_config_byte(hose, dev, 0x92, 0x62); /* device control */
+
+ if (te->device != 0xac56) {
+ pci_hose_write_config_byte(hose, dev, 0x93, 0x21); /* async interrupt enable */
+ pci_hose_write_config_word(hose, dev, 0xa8, 0x0000); /* reset GPIO */
+ pci_hose_write_config_word(hose, dev, 0xac, 0x0000); /* reset GPIO */
+ pci_hose_write_config_word(hose, dev, 0xaa, 0x0000); /* reset GPIO */
+ pci_hose_write_config_word(hose, dev, 0xae, 0x0000); /* reset GPIO */
+ } else {
+ pci_hose_write_config_byte(hose, dev, 0x93, 0x20); /* */
+ }
+ pci_hose_write_config_word(hose, dev, 0xa4, 0x8000); /* reset power management */
+
+
+ pci_hose_read_config_dword(hose, dev, PCI_BASE_ADDRESS_0, &io_base);
+ io_base &= ~0xfL;
+
+ writeb(0x07, io_base+0x803); /* route CSC irq though ExCA and enable IRQ7 */
+ writel(0, io_base+0x10); /* CLKRUN default */
+ writel(0, io_base+0x20); /* CLKRUN default */
+
+}
+
+
+static struct pci_config_table pci_sc520_spunk_config_table[] = {
+ { 0x104c, 0xac50, PCI_ANY_ID, 0, 0x0a, 0, pci_sc520_spunk_configure_cardbus, { 0, 0, 0} },
+ { 0x104c, 0xac56, PCI_ANY_ID, 0, 0x0a, 0, pci_sc520_spunk_configure_cardbus, { 0, 0, 0} },
+ { 0, 0, 0, 0, 0, 0, NULL, {0,0,0}}
+};
+
+static struct pci_controller sc520_spunk_hose = {
+ fixup_irq: pci_sc520_spunk_fixup_irq,
+ config_table: pci_sc520_spunk_config_table,
+ first_busno: 0x00,
+ last_busno: 0xff,
+};
+
+void pci_init_board(void)
+{
+ pci_sc520_init(&sc520_spunk_hose);
+}
+
+/*
+ * This function should map a chunk of size bytes
+ * of the system address space to the ISA bus
+ *
+ * The function will return the memory address
+ * as seen by the host (which may very will be the
+ * same as the bus address)
+ */
+u32 isa_map_rom(u32 bus_addr, int size)
+{
+ u32 par;
+
+ printf("isa_map_rom asked to map %d bytes at %x\n",
+ size, bus_addr);
+
+ par = size;
+ if (par < 0x80000) {
+ par = 0x80000;
+ }
+ par >>= 12;
+ par--;
+ par&=0x7f;
+ par <<= 18;
+ par |= (bus_addr>>12);
+ par |= 0x50000000;
+
+ printf ("setting PAR11 to %x\n", par);
+
+ /* Map rom 0x10000 with PAR1 */
+ sc520_mmcr->par[11] = par;
+
+ return bus_addr;
+}
+
+/*
+ * this function removed any mapping created
+ * with pci_get_rom_window()
+ */
+void isa_unmap_rom(u32 addr)
+{
+ printf("isa_unmap_rom asked to unmap %x", addr);
+ if ((addr>>12) == (sc520_mmcr->par[11] & 0x3ffff)) {
+ sc520_mmcr->par[11] = 0;
+ printf(" done\n");
+ return;
+ }
+ printf(" not ours\n");
+}
+
+#define PCI_ROM_TEMP_SPACE 0x10000
+/*
+ * This function should map a chunk of size bytes
+ * of the system address space to the PCI bus,
+ * suitable to map PCI ROMS (bus address < 16M)
+ * the function will return the host memory address
+ * which should be converted into a bus address
+ * before used to configure the PCI rom address
+ * decoder
+ */
+u32 pci_get_rom_window(struct pci_controller *hose, int size)
+{
+ u32 par;
+
+ par = size;
+ if (par < 0x80000) {
+ par = 0x80000;
+ }
+ par >>= 16;
+ par--;
+ par&=0x7ff;
+ par <<= 14;
+ par |= (PCI_ROM_TEMP_SPACE>>16);
+ par |= 0x72000000;
+
+ printf ("setting PAR1 to %x\n", par);
+
+ /* Map rom 0x10000 with PAR1 */
+ sc520_mmcr->par[1] = par;
+
+ return PCI_ROM_TEMP_SPACE;
+}
+
+/*
+ * this function removed any mapping created
+ * with pci_get_rom_window()
+ */
+void pci_remove_rom_window(struct pci_controller *hose, u32 addr)
+{
+ printf("pci_remove_rom_window: %x", addr);
+ if (addr == PCI_ROM_TEMP_SPACE) {
+ sc520_mmcr->par[1] = 0;
+ printf(" done\n");
+ return;
+ }
+ printf(" not ours\n");
+
+}
+
+/*
+ * This function is called in order to provide acces to the
+ * legacy video I/O ports on the PCI bus.
+ * After this function accesses to I/O ports 0x3b0-0x3bb and
+ * 0x3c0-0x3df shuld result in transactions on the PCI bus.
+ *
+ */
+int pci_enable_legacy_video_ports(struct pci_controller *hose)
+{
+ /* Map video memory to 0xa0000*/
+ sc520_mmcr->par[0] = 0x7200400a;
+
+ /* forward all I/O accesses to PCI */
+ sc520_mmcr->adddecctl = sc520_mmcr->adddecctl | IO_HOLE_DEST_PCI;
+
+
+ /* so we map away all io ports to pci (only way to access pci io
+ * below 0x400. But then we have to map back the portions that we dont
+ * use so that the generate cycles on the GPIO bus where the sio and
+ * ISA slots are connected, this requre the use of several PAR registers
+ */
+
+ /* bring 0x100 - 0x2f7 back to ISA using PAR5 */
+ sc520_mmcr->par[5] = 0x31f70100;
+
+ /* com2 use 2f8-2ff */
+
+ /* bring 0x300 - 0x3af back to ISA using PAR7 */
+ sc520_mmcr->par[7] = 0x30af0300;
+
+ /* vga use 3b0-3bb */
+
+ /* bring 0x3bc - 0x3bf back to ISA using PAR8 */
+ sc520_mmcr->par[8] = 0x300303bc;
+
+ /* vga use 3c0-3df */
+
+ /* bring 0x3e0 - 0x3f7 back to ISA using PAR9 */
+ sc520_mmcr->par[9] = 0x301703e0;
+
+ /* com1 use 3f8-3ff */
+
+ return 0;
+}
COBJS-y += bios_setup.o
COBJS-y += board.o
COBJS-y += bootm.o
-COBJS-y += pci.o
-COBJS-y += pci_type1.o
+COBJS-$(CONFIG_PCI) += pci.o
+COBJS-$(CONFIG_PCI) += pci_type1.o
COBJS-y += realmode.o
COBJS-y += video_bios.o
COBJS-y += video.o
#include <asm/io.h>
#include <asm/pci.h>
-#ifdef CONFIG_PCI
#undef PCI_ROM_SCAN_VERBOSE
int pci_shadow_rom(pci_dev_t dev, unsigned char *dest)
return res;
}
-
-#endif
*/
#include <common.h>
-
-#ifdef CONFIG_PCI
-
#include <asm/io.h>
#include <pci.h>
hose->cfg_addr = (unsigned int *) cfg_addr;
hose->cfg_data = (unsigned char *) cfg_data;
}
-
-#endif
projects / u-boot.git / commitdiff