When enabled, makes the IDE subsystem use 64bit sector addresses.
Default is 32bit.
-- SCSI Support:
- CONFIG_SYS_SCSI_MAX_LUN [8] and CONFIG_SYS_SCSI_MAX_SCSI_ID [7]
- can be adjusted to define the maximum numbers of LUNs and SCSI
- IDs.
-
- The environment variable 'scsidevs' is set to the number of
- SCSI devices found during the last scan.
-
- NETWORK Support (PCI):
CONFIG_E1000_SPI
Utility code for direct access to the SPI bus on Intel 8257x.
imply FIRMWARE
imply HASH_VERIFY
imply LZMA
- imply SCSI
imply TEE
imply AVB_VERIFY
imply LIBAVB
/* SATA */
#define AHCI_BASE_ADDR (CONFIG_SYS_IMMR + 0x02200000)
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
#ifdef CONFIG_DDR_SPD
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_LS1_DDR_BLOCK1_SIZE ((phys_size_t)2 << 30)
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_FSL_SATA=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_SYS_BR0_PRELIM_BOOL=y
CONFIG_SYS_BR0_PRELIM=0xFE001001
CONFIG_SYS_OR0_PRELIM=0xFF800193
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=66666666
CONFIG_DM_I2C=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_BR0_PRELIM_BOOL=y
CONFIG_SYS_BR0_PRELIM=0xFFA00C21
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_BR0_PRELIM_BOOL=y
CONFIG_SYS_BR0_PRELIM=0xE8001001
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_BR0_PRELIM_BOOL=y
CONFIG_SYS_BR0_PRELIM=0xE8001001
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_SYS_BR0_PRELIM_BOOL=y
CONFIG_SYS_BR0_PRELIM=0xE8001001
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
CONFIG_DDR_ECC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
CONFIG_DDR_ECC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
CONFIG_DDR_ECC=y
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
CONFIG_DDR_ECC=y
CONFIG_ENV_IS_IN_REMOTE=y
CONFIG_ENV_ADDR=0xFFE20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
CONFIG_DDR_ECC=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
CONFIG_DDR_ECC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=133330000
CONFIG_DDR_ECC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=133330000
CONFIG_DDR_ECC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=133330000
CONFIG_DDR_ECC=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=133330000
CONFIG_DDR_ECC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=133330000
CONFIG_DDR_ECC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=133330000
CONFIG_DDR_ECC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=133330000
CONFIG_DDR_ECC=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=133330000
CONFIG_DDR_ECC=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=133333333
CONFIG_DDR_ECC=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_ENV_ADDR=0xEFF20000
CONFIG_DM=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_FSL_CAAM=y
CONFIG_DDR_CLK_FREQ=133333333
CONFIG_DDR_ECC=y
CONFIG_PMIC_PALMAS=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_PALMAS=y
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_DM_SERIAL=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCI_MVEBU=y
CONFIG_SCSI=y
+CONFIG_SCSI_AHCI_PLAT=y
+CONFIG_SYS_SCSI_MAX_SCSI_ID=2
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_SYS_NS16550=y
CONFIG_KIRKWOOD_SPI=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_KIRKWOOD_GPIO=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_MVTWSI=y
# CONFIG_MMC is not set
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
CONFIG_SYS_ATA_STRIDE=4
CONFIG_SYS_ATA_DATA_OFFSET=0x100
CONFIG_SYS_ATA_REG_OFFSET=0x100
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
# CONFIG_MMC is not set
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
# CONFIG_MMC is not set
CONFIG_CALXEDA_XGMAC=y
CONFIG_SCSI=y
+CONFIG_SCSI_AHCI_PLAT=y
+CONFIG_SYS_SCSI_MAX_SCSI_ID=5
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
CONFIG_KIRKWOOD_GPIO=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_NVME=y
CONFIG_PCI=y
CONFIG_PCIE_LAYERSCAPE_RC=y
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_NVME=y
CONFIG_PCI=y
CONFIG_PCIE_LAYERSCAPE_RC=y
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_PCIE_LAYERSCAPE_RC=y
CONFIG_U_QE=y
CONFIG_SYS_QE_FW_ADDR=0x940000
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_POWER_LEGACY=y
CONFIG_POWER_I2C=y
CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_FSL_LS_MDIO=y
CONFIG_PCI=y
CONFIG_PCIE_LAYERSCAPE_RC=y
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
CONFIG_KIRKWOOD_GPIO=y
# CONFIG_MMC is not set
CONFIG_MTD=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
CONFIG_KIRKWOOD_GPIO=y
# CONFIG_MMC is not set
CONFIG_MTD=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_KIRKWOOD_GPIO=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
CONFIG_KIRKWOOD_GPIO=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_KIRKWOOD_GPIO=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
CONFIG_BLK=y
CONFIG_KIRKWOOD_GPIO=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
CONFIG_KIRKWOOD_GPIO=y
CONFIG_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MVTWSI=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
# CONFIG_MMC is not set
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
CONFIG_MMC_OMAP_HS=y
CONFIG_DM_ETH=y
CONFIG_SCSI=y
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_CONS_INDEX=3
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
CONFIG_SYS_QE_FW_ADDR=0x60020000
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_SPECIFY_CONSOLE_INDEX=y
CONFIG_DM_SERIAL=y
CONFIG_SYS_NS16550=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
CONFIG_SYS_QE_FW_ADDR=0x60020000
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_SPECIFY_CONSOLE_INDEX=y
CONFIG_DM_SERIAL=y
CONFIG_SYS_NS16550=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
CONFIG_SYS_QE_FW_ADDR=0x60020000
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_SPECIFY_CONSOLE_INDEX=y
CONFIG_DM_SERIAL=y
CONFIG_SYS_NS16550=y
CONFIG_MII=y
CONFIG_TSEC_ENET=y
CONFIG_SYS_QE_FW_ADDR=0x60020000
+CONFIG_SCSI_AHCI_PLAT=y
CONFIG_SPECIFY_CONSOLE_INDEX=y
CONFIG_DM_SERIAL=y
CONFIG_SYS_NS16550=y
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
CONFIG_KIRKWOOD_GPIO=y
# CONFIG_MMC_HW_PARTITIONING is not set
CONFIG_MVEBU_MMC=y
CONFIG_DEBUG_DEVRES=y
CONFIG_ADC=y
CONFIG_ADC_SANDBOX=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_AXI=y
CONFIG_AXI_SANDBOX=y
CONFIG_SYS_IDE_MAXBUS=1
CONFIG_SIMPLE_PM_BUS=y
CONFIG_ADC=y
CONFIG_ADC_SANDBOX=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_AXI=y
CONFIG_AXI_SANDBOX=y
CONFIG_SYS_IDE_MAXBUS=1
CONFIG_DM_RNG=y
CONFIG_DM_RTC=y
CONFIG_RTC_RV8803=y
+CONFIG_SCSI_AHCI_PLAT=y
+CONFIG_SYS_SCSI_MAX_SCSI_ID=8
+CONFIG_SYS_SCSI_MAX_LUN=4
CONFIG_SANDBOX_SERIAL=y
CONFIG_SMEM=y
CONFIG_SANDBOX_SMEM=y
CONFIG_SOUND_SANDBOX=y
CONFIG_SOC_DEVICE=y
CONFIG_SANDBOX_SPI=y
+CONFIG_SCSI=y
CONFIG_SPMI=y
CONFIG_SPMI_SANDBOX=y
CONFIG_SYSINFO=y
CONFIG_DEBUG_DEVRES=y
CONFIG_ADC=y
CONFIG_ADC_SANDBOX=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_AXI=y
CONFIG_AXI_SANDBOX=y
CONFIG_CLK=y
# CONFIG_SPL_SIMPLE_BUS is not set
CONFIG_ADC=y
CONFIG_ADC_SANDBOX=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_AXI=y
CONFIG_AXI_SANDBOX=y
CONFIG_SYS_IDE_MAXBUS=1
# CONFIG_SPL_SIMPLE_BUS is not set
CONFIG_ADC=y
CONFIG_ADC_SANDBOX=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_AXI=y
CONFIG_AXI_SANDBOX=y
CONFIG_SYS_IDE_MAXBUS=1
CONFIG_DM=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_MVEBU_MMC=y
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
CONFIG_SPL_OF_TRANSLATE=y
CONFIG_SATA=y
CONFIG_SATA_MV=y
+CONFIG_SYS_SATA_MAX_DEVICE=1
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_RAM=y
CONFIG_FPGA_ALTERA=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
# CONFIG_NET is not set
# CONFIG_ACPIGEN is not set
+CONFIG_SYS_SATA_MAX_DEVICE=2
CONFIG_AXI=y
CONFIG_AXI_SANDBOX=y
CONFIG_SANDBOX_GPIO=y
Enable this driver to support the SIL3131, SIL3132 and SIL3124
SATA controllers.
+config SYS_SATA_MAX_DEVICE
+ int "Maximum number of SATA devices"
+ depends on !AHCI || FSL_SATA || SATA_MV
+ help
+ Sets the maximum number of SATA devices which can be supported
+ by U-Boot.
+
+ This is only partially converted to driver model. See sata_bread()
+ for example, which shows where the conversion needs to be completed.
+
endif # SATA
endmenu
which supports SCSI and SATA HDDs. For every device configuration
(IDs/LUNs) a block device is created with RAW read/write and
filesystem support.
+
+if SCSI && !DM_SCSI
+
+config SCSI_AHCI_PLAT
+ bool "Platform-specific init of AHCI"
+ help
+ This enables a way for boards to set up an AHCI device manually, by
+ called ahci_init() and providing an ahci_reset() mechanism.
+
+ This is deprecated. An AHCI driver should be provided instead.
+
+config SYS_SCSI_MAX_SCSI_ID
+ int "Maximum supporedt SCSI ID"
+ default 1
+ help
+ Sets the maximum number of SCSI IDs to scan when looking for devices.
+ IDs from 0 to (this value - 1) are scanned.
+
+ This is deprecated and is not needed when BLK is enabled.
+
+config SYS_SCSI_MAX_LUN
+ int "Maximum support SCSI LUN"
+ default 1
+ help
+ Sets the maximum number of SCSI Logical Unit Numbers (LUNs) to scan on
+ devices. LUNs from 0 to (this value - 1) are scanned.
+
+ This is deprecated and is not needed when CONFIG_DM_SCSI is enabled.
+
+endif
endif
endif
+ifdef CONFIG_SCSI
obj-$(CONFIG_SANDBOX) += sandbox_scsi.o
+endif
/*
* SATA
*/
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1_OFFSET 0x18000
#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
#define CONFIG_FSL_SATA_V2
#ifdef CONFIG_FSL_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_FSL_SATA_V2
#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_PCIE3
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_LBA48
#define CONFIG_SYS_SRIO
/* SATA */
#define CONFIG_FSL_SATA_V2
#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
* SATA
*/
#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
* SATA
*/
#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
/* SATA */
#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
/* SATA */
#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_NET_RETRY_COUNT 10
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs longer aneg time at 1G */
-/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
/*
* Default to using SPI for environment, etc.
* 0x000000 - 0x040000 : QSPI.SPL (256KiB)
#define CONFIG_PCI_SCAN_SHOW
#endif
-/* SATA support */
-#ifdef CONFIG_SCSI
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#endif
-
/* Keep device tree and initrd in lower memory so the kernel can access them */
#define RELOCATION_LIMITS_ENV_SETTINGS \
"fdt_high=0x10000000\0" \
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
/* SATA */
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_LBA48
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
* U-Boot into it.
*/
-/*
- * SATA/SCSI/AHCI configuration
- */
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
/* Environment in SPI NOR flash */
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
/* SATA */
#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
/* I2C */
#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
-/*
- * SATA/SCSI/AHCI configuration
- */
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
/* Environment in SPI NOR flash */
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
/* SATA support */
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_LBA48
/* PCIe support */
/* SPI SPL */
-/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
-
/* NAND support */
#ifdef CONFIG_MTD_RAW_NAND
/* NAND: device related configs */
* SATA Driver configuration
*/
#ifdef CONFIG_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_LBA48
#endif /* CONFIG_SATA */
/* PCI CONFIG */
#define CONFIG_PCI_SCAN_SHOW
-/* SCSI */
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SATA_MAX_DEVICE 4
-
/* BOOT */
#define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024)
/* SATA Configs */
#ifdef CONFIG_CMD_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
#endif
/* SATA driver configuration */
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_LBA48
#endif /* _CONFIG_GOFLEXHOME_H */
* SATA Configs
*/
#ifdef CONFIG_CMD_SATA
- #define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
#define CONFIG_PCI_SCAN_SHOW
#endif
-/* SATA support */
-#ifdef CONFIG_SCSI
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#endif
-
/* Keep device tree and initrd in lower memory so the kernel can access them */
#define RELOCATION_LIMITS_ENV_SETTINGS \
"fdt_high=0x10000000\0" \
#define CONFIG_SYS_BOOTCOUNT_LE /* Use little-endian accessors */
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 5
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
#define CONFIG_BOOT_RETRY_TIME -1
#define CONFIG_RESET_TO_RETRY
#define CONFIG_LBA48
#if defined(CONFIG_NETSPACE_MAX_V2) || defined(CONFIG_D2NET_V2) || \
defined(CONFIG_NET2BIG_V2)
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
-#else
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#endif
#endif /* CONFIG_SATA */
#define CONFIG_SYS_SDRAM_SIZE 0x40000000
/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA AHCI_BASE_ADDR
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"verify=no\0" \
#define CONFIG_SYS_FSL_QSPI_BASE 0x40000000
/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA AHCI_BASE_ADDR
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
/* I2C */
/* GPIO */
*/
/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
#ifndef PCI_DEVICE_ID_FREESCALE_AHCI
#define PCI_DEVICE_ID_FREESCALE_AHCI 0x0440
#endif
#define CONFIG_SCSI_DEV_LIST {PCI_VENDOR_ID_FREESCALE, \
PCI_DEVICE_ID_FREESCALE_AHCI}
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
/* SPI */
/*
#endif
/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
#ifndef SPL_NO_ENV
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
#endif
/* SATA */
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
#define SCSI_VEND_ID 0x1b4b
#define SCSI_DEV_ID 0x9170
#define CONFIG_SCSI_DEV_LIST {SCSI_VEND_ID, SCSI_DEV_ID}
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
/* Initial environment variables */
#endif
/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
/* EEPROM */
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_SATA AHCI_BASE_ADDR
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
/*
* IFC Definitions
*/
/* SATA */
#ifndef SPL_NO_SATA
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
-#define CONFIG_SYS_SCSI_MAX_LUN 2
#define SCSI_VEND_ID 0x1b4b
#define SCSI_DEV_ID 0x9170
#define CONFIG_SCSI_DEV_LIST {SCSI_VEND_ID, SCSI_DEV_ID}
/* SATA */
#ifndef SPL_NO_SATA
-#define CONFIG_SCSI_AHCI_PLAT
-
#define CONFIG_SYS_SATA AHCI_BASE_ADDR
-
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
#endif
/* FMan ucode */
/* SATA */
#ifdef CONFIG_SCSI
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
-
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
#endif
/* Physical Memory Map */
#endif
/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024)
#endif
/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
#if !defined(CONFIG_FSL_QSPI) || defined(CONFIG_TFABOOT)
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
#endif /* CONFIG_CMD_NET */
#ifdef CONFIG_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_SYS_64BIT_LBA
#define CONFIG_LBA48
#endif
/* SATA */
#ifdef CONFIG_SCSI
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
#endif
/* USB */
* SATA
*/
#ifdef CONFIG_CMD_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_BASE_ADDR
#define CONFIG_LBA48
/*
* SATA/SCSI/AHCI configuration
*/
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_LBA48
#define CONFIG_SYS_64BIT_LBA
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 1) \
func(MMC, mmc, 0) \
/*
* SATA/SCSI/AHCI configuration
*/
-#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_LBA48
#define CONFIG_SYS_64BIT_LBA
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
/*
* PCI configuration
*/
#define CONFIG_BOARD_SIZE_LIMIT 785408
#ifdef CONFIG_CMD_SATA
- #define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_BASE_ADDR
#define CONFIG_LBA48
/* SATA Configuration */
#ifdef CONFIG_CMD_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
* SATA Configs
*/
#ifdef CONFIG_CMD_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
/* SATA driver configuration */
#ifdef CONFIG_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_LBA48
#endif /* CONFIG_SATA */
#define CONSOLEDEV "ttyS2"
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-
#endif /* __CONFIG_OMAP5_EVM_H */
#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_LBA48
#define CONFIG_HWCONFIG
#undef CONFIG_RESET_PHY_R /* remove legacy reset_phy() */
#endif
-/*
- * SATA Driver configuration
- */
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
-
/*
* Support large disk for SATA and USB
*/
#define CONFIG_SANDBOX_SDL
#endif
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 8
-#define CONFIG_SYS_SCSI_MAX_LUN 4
-
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
-
#endif
* SATA driver configuration
*/
#ifdef CONFIG_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_LBA48
#endif /* CONFIG_SATA */
#define CONFIG_STANDALONE_LOAD_ADDR 0x80200000
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
-
/* Environment options */
#ifndef CONFIG_SPL_BUILD
/* SATA */
#ifdef CONFIG_CMD_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
"initrd_high=0x10000000\0"
/* SATA support */
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_LBA48
/* Enable LCD and reserve 512KB from top of memory*/
/* SATA Configs */
#ifdef CONFIG_CMD_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
CONFIG_SATA1
CONFIG_SATA2
CONFIG_SCIF_A
-CONFIG_SCSI_AHCI_PLAT
CONFIG_SCSI_DEV_LIST
CONFIG_SC_TIMER_CLK
CONFIG_SDCARD
CONFIG_SYS_SATA2_FLAGS
CONFIG_SYS_SATA2_OFFSET
CONFIG_SYS_SATA_FAT_BOOT_PARTITION
-CONFIG_SYS_SATA_MAX_DEVICE
CONFIG_SYS_SBFHDR_DATA_OFFSET
CONFIG_SYS_SBFHDR_SIZE
CONFIG_SYS_SCCR_SATACM
CONFIG_SYS_SCCR_TSEC2CM
CONFIG_SYS_SCCR_USBDRCM
CONFIG_SYS_SCR
-CONFIG_SYS_SCSI_MAX_LUN
-CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SDRAM
CONFIG_SYS_SDRAM_BASE
CONFIG_SYS_SDRAM_BASE0