spi: zynq_qspi: Use clk subsystem to get reference qspi clk

Remove fixed reference clk used by plat->frequency and use clk
subsystem to get reference clk. As per spi dt bindings
"spi-max-frequency" property should be used by the slave devices.
This property is read by spi-uclass driver for the slave device.
So avoid reading above property from the platform driver.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

diff --git a/drivers/spi/zynq_qspi.c b/drivers/spi/zynq_qspi.c
index 3f39ef05f2d6adfd7845f2bb176576035689c0c1..4219a35c840644e76acbc664554e1ad95fee10c7 100644 (file)
--- a/drivers/spi/zynq_qspi.c
+++ b/drivers/spi/zynq_qspi.c
@@ -6,8 +6,10 @@
  * Xilinx Zynq Quad-SPI(QSPI) controller driver (master mode only)
  */
 
+#include <clk.h>
 #include <common.h>
 #include <dm.h>
+#include <dm/device_compat.h>
 #include <log.h>
 #include <malloc.h>
 #include <spi.h>
@@ -105,14 +107,6 @@ static int zynq_qspi_ofdata_to_platdata(struct udevice *bus)
        plat->regs = (struct zynq_qspi_regs *)fdtdec_get_addr(blob,
                                                              node, "reg");
 
-       /* FIXME: Use 166MHz as a suitable default */
-       plat->frequency = fdtdec_get_int(blob, node, "spi-max-frequency",
-                                       166666666);
-       plat->speed_hz = plat->frequency / 2;
-
-       debug("%s: regs=%p max-frequency=%d\n", __func__,
-             plat->regs, plat->frequency);
-
        return 0;
 }
 
@@ -159,13 +153,39 @@ static int zynq_qspi_probe(struct udevice *bus)
 {
        struct zynq_qspi_platdata *plat = dev_get_platdata(bus);
        struct zynq_qspi_priv *priv = dev_get_priv(bus);
+       struct clk clk;
+       unsigned long clock;
+       int ret;
 
        priv->regs = plat->regs;
        priv->fifo_depth = ZYNQ_QSPI_FIFO_DEPTH;
 
+       ret = clk_get_by_name(bus, "ref_clk", &clk);
+       if (ret < 0) {
+               dev_err(bus, "failed to get clock\n");
+               return ret;
+       }
+
+       clock = clk_get_rate(&clk);
+       if (IS_ERR_VALUE(clock)) {
+               dev_err(bus, "failed to get rate\n");
+               return clock;
+       }
+
+       ret = clk_enable(&clk);
+       if (ret && ret != -ENOSYS) {
+               dev_err(bus, "failed to enable clock\n");
+               return ret;
+       }
+
        /* init the zynq spi hw */
        zynq_qspi_init_hw(priv);
 
+       plat->frequency = clock;
+       plat->speed_hz = plat->frequency / 2;
+
+       debug("%s: max-frequency=%d\n", __func__, plat->speed_hz);
+
        return 0;
 }