--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Motorcomm 8531 PHY driver.
+ *
+ * Copyright (C) 2023 StarFive Technology Co., Ltd.
+ */
+
+#include <config.h>
+#include <common.h>
+#include <malloc.h>
+#include <phy.h>
+#include <linux/bitfield.h>
+
+#define PHY_ID_YT8531 0x4f51e91b
+#define PHY_ID_MASK GENMASK(31, 0)
+
+/* Extended Register's Address Offset Register */
+#define YTPHY_PAGE_SELECT 0x1E
+
+/* Extended Register's Data Register */
+#define YTPHY_PAGE_DATA 0x1F
+
+#define YTPHY_SYNCE_CFG_REG 0xA012
+
+#define YTPHY_DTS_OUTPUT_CLK_DIS 0
+#define YTPHY_DTS_OUTPUT_CLK_25M 25000000
+#define YTPHY_DTS_OUTPUT_CLK_125M 125000000
+
+#define YT8531_SCR_SYNCE_ENABLE BIT(6)
+/* 1b0 output 25m clock *default*
+ * 1b1 output 125m clock
+ */
+#define YT8531_SCR_CLK_FRE_SEL_125M BIT(4)
+#define YT8531_SCR_CLK_SRC_MASK GENMASK(3, 1)
+#define YT8531_SCR_CLK_SRC_PLL_125M 0
+#define YT8531_SCR_CLK_SRC_UTP_RX 1
+#define YT8531_SCR_CLK_SRC_SDS_RX 2
+#define YT8531_SCR_CLK_SRC_CLOCK_FROM_DIGITAL 3
+#define YT8531_SCR_CLK_SRC_REF_25M 4
+#define YT8531_SCR_CLK_SRC_SSC_25M 5
+
+/* 1b0 use original tx_clk_rgmii *default*
+ * 1b1 use inverted tx_clk_rgmii.
+ */
+#define YT8531_RC1R_TX_CLK_SEL_INVERTED BIT(14)
+#define YT8531_RC1R_RX_DELAY_MASK GENMASK(13, 10)
+#define YT8531_RC1R_FE_TX_DELAY_MASK GENMASK(7, 4)
+#define YT8531_RC1R_GE_TX_DELAY_MASK GENMASK(3, 0)
+#define YT8531_RC1R_RGMII_0_000_NS 0
+#define YT8531_RC1R_RGMII_0_150_NS 1
+#define YT8531_RC1R_RGMII_0_300_NS 2
+#define YT8531_RC1R_RGMII_0_450_NS 3
+#define YT8531_RC1R_RGMII_0_600_NS 4
+#define YT8531_RC1R_RGMII_0_750_NS 5
+#define YT8531_RC1R_RGMII_0_900_NS 6
+#define YT8531_RC1R_RGMII_1_050_NS 7
+#define YT8531_RC1R_RGMII_1_200_NS 8
+#define YT8531_RC1R_RGMII_1_350_NS 9
+#define YT8531_RC1R_RGMII_1_500_NS 10
+#define YT8531_RC1R_RGMII_1_650_NS 11
+#define YT8531_RC1R_RGMII_1_800_NS 12
+#define YT8531_RC1R_RGMII_1_950_NS 13
+#define YT8531_RC1R_RGMII_2_100_NS 14
+#define YT8531_RC1R_RGMII_2_250_NS 15
+
+/* Phy gmii clock gating Register */
+#define YT8531_CLOCK_GATING_REG 0xC
+#define YT8531_CGR_RX_CLK_EN BIT(12)
+
+/* Specific Status Register */
+#define YTPHY_SPECIFIC_STATUS_REG 0x11
+#define YTPHY_DUPLEX_MASK BIT(13)
+#define YTPHY_DUPLEX_SHIFT 13
+#define YTPHY_SPEED_MODE_MASK GENMASK(15, 14)
+#define YTPHY_SPEED_MODE_SHIFT 14
+
+#define YT8531_EXTREG_SLEEP_CONTROL1_REG 0x27
+#define YT8531_ESC1R_SLEEP_SW BIT(15)
+#define YT8531_ESC1R_PLLON_SLP BIT(14)
+
+#define YT8531_RGMII_CONFIG1_REG 0xA003
+
+#define YT8531_CHIP_CONFIG_REG 0xA001
+#define YT8531_CCR_SW_RST BIT(15)
+/* 1b0 disable 1.9ns rxc clock delay *default*
+ * 1b1 enable 1.9ns rxc clock delay
+ */
+#define YT8531_CCR_RXC_DLY_EN BIT(8)
+#define YT8531_CCR_RXC_DLY_1_900_NS 1900
+
+/* bits in struct ytphy_plat_priv->flag */
+#define TX_CLK_ADJ_ENABLED BIT(0)
+#define AUTO_SLEEP_DISABLED BIT(1)
+#define KEEP_PLL_ENABLED BIT(2)
+#define TX_CLK_10_INVERTED BIT(3)
+#define TX_CLK_100_INVERTED BIT(4)
+#define TX_CLK_1000_INVERTED BIT(5)
+
+struct ytphy_plat_priv {
+ u32 rx_delay_ps;
+ u32 tx_delay_ps;
+ u32 clk_out_frequency;
+ u32 flag;
+};
+
+/**
+ * struct ytphy_cfg_reg_map - map a config value to a register value
+ * @cfg: value in device configuration
+ * @reg: value in the register
+ */
+struct ytphy_cfg_reg_map {
+ u32 cfg;
+ u32 reg;
+};
+
+static const struct ytphy_cfg_reg_map ytphy_rgmii_delays[] = {
+ /* for tx delay / rx delay with YT8531_CCR_RXC_DLY_EN is not set. */
+ { 0, YT8531_RC1R_RGMII_0_000_NS },
+ { 150, YT8531_RC1R_RGMII_0_150_NS },
+ { 300, YT8531_RC1R_RGMII_0_300_NS },
+ { 450, YT8531_RC1R_RGMII_0_450_NS },
+ { 600, YT8531_RC1R_RGMII_0_600_NS },
+ { 750, YT8531_RC1R_RGMII_0_750_NS },
+ { 900, YT8531_RC1R_RGMII_0_900_NS },
+ { 1050, YT8531_RC1R_RGMII_1_050_NS },
+ { 1200, YT8531_RC1R_RGMII_1_200_NS },
+ { 1350, YT8531_RC1R_RGMII_1_350_NS },
+ { 1500, YT8531_RC1R_RGMII_1_500_NS },
+ { 1650, YT8531_RC1R_RGMII_1_650_NS },
+ { 1800, YT8531_RC1R_RGMII_1_800_NS },
+ { 1950, YT8531_RC1R_RGMII_1_950_NS }, /* default tx/rx delay */
+ { 2100, YT8531_RC1R_RGMII_2_100_NS },
+ { 2250, YT8531_RC1R_RGMII_2_250_NS },
+
+ /* only for rx delay with YT8531_CCR_RXC_DLY_EN is set. */
+ { 0 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_000_NS },
+ { 150 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_150_NS },
+ { 300 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_300_NS },
+ { 450 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_450_NS },
+ { 600 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_600_NS },
+ { 750 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_750_NS },
+ { 900 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_0_900_NS },
+ { 1050 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_050_NS },
+ { 1200 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_200_NS },
+ { 1350 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_350_NS },
+ { 1500 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_500_NS },
+ { 1650 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_650_NS },
+ { 1800 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_800_NS },
+ { 1950 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_1_950_NS },
+ { 2100 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_2_100_NS },
+ { 2250 + YT8531_CCR_RXC_DLY_1_900_NS, YT8531_RC1R_RGMII_2_250_NS }
+};
+
+static u32 ytphy_get_delay_reg_value(struct phy_device *phydev,
+ u32 val,
+ u16 *rxc_dly_en)
+{
+ int tb_size = ARRAY_SIZE(ytphy_rgmii_delays);
+ int tb_size_half = tb_size / 2;
+ int i;
+
+ /* when rxc_dly_en is NULL, it is get the delay for tx, only half of
+ * tb_size is valid.
+ */
+ if (!rxc_dly_en)
+ tb_size = tb_size_half;
+
+ for (i = 0; i < tb_size; i++) {
+ if (ytphy_rgmii_delays[i].cfg == val) {
+ if (rxc_dly_en && i < tb_size_half)
+ *rxc_dly_en = 0;
+ return ytphy_rgmii_delays[i].reg;
+ }
+ }
+
+ pr_warn("Unsupported value %d, using default (%u)\n",
+ val, YT8531_RC1R_RGMII_1_950_NS);
+
+ /* when rxc_dly_en is not NULL, it is get the delay for rx.
+ * The rx default in dts and ytphy_rgmii_clk_delay_config is 1950 ps,
+ * so YT8531_CCR_RXC_DLY_EN should not be set.
+ */
+ if (rxc_dly_en)
+ *rxc_dly_en = 0;
+
+ return YT8531_RC1R_RGMII_1_950_NS;
+}
+
+static int ytphy_modify_ext(struct phy_device *phydev, u16 regnum, u16 mask,
+ u16 set)
+{
+ int ret;
+
+ ret = phy_write(phydev, MDIO_DEVAD_NONE, YTPHY_PAGE_SELECT, regnum);
+ if (ret < 0)
+ return ret;
+
+ return phy_modify(phydev, MDIO_DEVAD_NONE, YTPHY_PAGE_DATA, mask, set);
+}
+
+static int ytphy_rgmii_clk_delay_config(struct phy_device *phydev)
+{
+ struct ytphy_plat_priv *priv = phydev->priv;
+ u16 rxc_dly_en = YT8531_CCR_RXC_DLY_EN;
+ u32 rx_reg, tx_reg;
+ u16 mask, val = 0;
+ int ret;
+
+ rx_reg = ytphy_get_delay_reg_value(phydev, priv->rx_delay_ps,
+ &rxc_dly_en);
+ tx_reg = ytphy_get_delay_reg_value(phydev, priv->tx_delay_ps,
+ NULL);
+
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ rxc_dly_en = 0;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ val |= FIELD_PREP(YT8531_RC1R_RX_DELAY_MASK, rx_reg);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ rxc_dly_en = 0;
+ val |= FIELD_PREP(YT8531_RC1R_GE_TX_DELAY_MASK, tx_reg);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ val |= FIELD_PREP(YT8531_RC1R_RX_DELAY_MASK, rx_reg) |
+ FIELD_PREP(YT8531_RC1R_GE_TX_DELAY_MASK, tx_reg);
+ break;
+ default: /* do not support other modes */
+ return -EOPNOTSUPP;
+ }
+
+ ret = ytphy_modify_ext(phydev, YT8531_CHIP_CONFIG_REG,
+ YT8531_CCR_RXC_DLY_EN, rxc_dly_en);
+ if (ret < 0)
+ return ret;
+
+ /* Generally, it is not necessary to adjust YT8531_RC1R_FE_TX_DELAY */
+ mask = YT8531_RC1R_RX_DELAY_MASK | YT8531_RC1R_GE_TX_DELAY_MASK;
+ return ytphy_modify_ext(phydev, YT8531_RGMII_CONFIG1_REG, mask, val);
+}
+
+static int yt8531_parse_status(struct phy_device *phydev)
+{
+ int val;
+ int speed, speed_mode;
+
+ val = phy_read(phydev, MDIO_DEVAD_NONE, YTPHY_SPECIFIC_STATUS_REG);
+ if (val < 0)
+ return val;
+
+ speed_mode = (val & YTPHY_SPEED_MODE_MASK) >> YTPHY_SPEED_MODE_SHIFT;
+ switch (speed_mode) {
+ case 2:
+ speed = SPEED_1000;
+ break;
+ case 1:
+ speed = SPEED_100;
+ break;
+ default:
+ speed = SPEED_10;
+ break;
+ }
+
+ phydev->speed = speed;
+ phydev->duplex = (val & YTPHY_DUPLEX_MASK) >> YTPHY_DUPLEX_SHIFT;
+
+ return 0;
+}
+
+static int yt8531_startup(struct phy_device *phydev)
+{
+ struct ytphy_plat_priv *priv = phydev->priv;
+ u16 val = 0;
+ int ret;
+
+ ret = genphy_update_link(phydev);
+ if (ret)
+ return ret;
+
+ ret = yt8531_parse_status(phydev);
+ if (ret)
+ return ret;
+
+ if (phydev->speed < 0)
+ return -EINVAL;
+
+ if (!(priv->flag & TX_CLK_ADJ_ENABLED))
+ return 0;
+
+ switch (phydev->speed) {
+ case SPEED_1000:
+ if (priv->flag & TX_CLK_1000_INVERTED)
+ val = YT8531_RC1R_TX_CLK_SEL_INVERTED;
+ break;
+ case SPEED_100:
+ if (priv->flag & TX_CLK_100_INVERTED)
+ val = YT8531_RC1R_TX_CLK_SEL_INVERTED;
+ break;
+ case SPEED_10:
+ if (priv->flag & TX_CLK_10_INVERTED)
+ val = YT8531_RC1R_TX_CLK_SEL_INVERTED;
+ break;
+ default:
+ printf("UNKNOWN SPEED\n");
+ return -EINVAL;
+ }
+
+ ret = ytphy_modify_ext(phydev, YT8531_RGMII_CONFIG1_REG,
+ YT8531_RC1R_TX_CLK_SEL_INVERTED, val);
+ if (ret < 0)
+ pr_warn("Modify TX_CLK_SEL err:%d\n", ret);
+
+ return 0;
+}
+
+static void ytphy_dt_parse(struct phy_device *phydev)
+{
+ struct ytphy_plat_priv *priv = phydev->priv;
+
+ priv->clk_out_frequency = ofnode_read_u32_default(phydev->node,
+ "motorcomm,clk-out-frequency-hz",
+ YTPHY_DTS_OUTPUT_CLK_DIS);
+ priv->rx_delay_ps = ofnode_read_u32_default(phydev->node,
+ "rx-internal-delay-ps",
+ YT8531_RC1R_RGMII_1_950_NS);
+ priv->tx_delay_ps = ofnode_read_u32_default(phydev->node,
+ "tx-internal-delay-ps",
+ YT8531_RC1R_RGMII_1_950_NS);
+
+ if (ofnode_read_bool(phydev->node, "motorcomm,auto-sleep-disabled"))
+ priv->flag |= AUTO_SLEEP_DISABLED;
+
+ if (ofnode_read_bool(phydev->node, "motorcomm,keep-pll-enabled"))
+ priv->flag |= KEEP_PLL_ENABLED;
+
+ if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-adj-enabled"))
+ priv->flag |= TX_CLK_ADJ_ENABLED;
+
+ if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-10-inverted"))
+ priv->flag |= TX_CLK_10_INVERTED;
+
+ if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-100-inverted"))
+ priv->flag |= TX_CLK_100_INVERTED;
+
+ if (ofnode_read_bool(phydev->node, "motorcomm,tx-clk-1000-inverted"))
+ priv->flag |= TX_CLK_1000_INVERTED;
+}
+
+static int yt8531_config(struct phy_device *phydev)
+{
+ struct ytphy_plat_priv *priv = phydev->priv;
+ u16 mask, val;
+ int ret;
+
+ ret = genphy_config_aneg(phydev);
+ if (ret < 0)
+ return ret;
+
+ ytphy_dt_parse(phydev);
+ switch (priv->clk_out_frequency) {
+ case YTPHY_DTS_OUTPUT_CLK_DIS:
+ mask = YT8531_SCR_SYNCE_ENABLE;
+ val = 0;
+ break;
+ case YTPHY_DTS_OUTPUT_CLK_25M:
+ mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK |
+ YT8531_SCR_CLK_FRE_SEL_125M;
+ val = YT8531_SCR_SYNCE_ENABLE |
+ FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+ YT8531_SCR_CLK_SRC_REF_25M);
+ break;
+ case YTPHY_DTS_OUTPUT_CLK_125M:
+ mask = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_SRC_MASK |
+ YT8531_SCR_CLK_FRE_SEL_125M;
+ val = YT8531_SCR_SYNCE_ENABLE | YT8531_SCR_CLK_FRE_SEL_125M |
+ FIELD_PREP(YT8531_SCR_CLK_SRC_MASK,
+ YT8531_SCR_CLK_SRC_PLL_125M);
+ break;
+ default:
+ pr_warn("Freq err:%u\n", priv->clk_out_frequency);
+ return -EINVAL;
+ }
+
+ ret = ytphy_modify_ext(phydev, YTPHY_SYNCE_CFG_REG, mask,
+ val);
+ if (ret < 0)
+ return ret;
+
+ ret = ytphy_rgmii_clk_delay_config(phydev);
+ if (ret < 0)
+ return ret;
+
+ if (priv->flag & AUTO_SLEEP_DISABLED) {
+ /* disable auto sleep */
+ ret = ytphy_modify_ext(phydev,
+ YT8531_EXTREG_SLEEP_CONTROL1_REG,
+ YT8531_ESC1R_SLEEP_SW, 0);
+ if (ret < 0)
+ return ret;
+ }
+
+ if (priv->flag & KEEP_PLL_ENABLED) {
+ /* enable RXC clock when no wire plug */
+ ret = ytphy_modify_ext(phydev,
+ YT8531_CLOCK_GATING_REG,
+ YT8531_CGR_RX_CLK_EN, 0);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int yt8531_probe(struct phy_device *phydev)
+{
+ struct ytphy_plat_priv *priv;
+
+ priv = calloc(1, sizeof(struct ytphy_plat_priv));
+ if (!priv)
+ return -ENOMEM;
+
+ phydev->priv = priv;
+
+ return 0;
+}
+
+U_BOOT_PHY_DRIVER(motorcomm8531) = {
+ .name = "YT8531 Gigabit Ethernet",
+ .uid = PHY_ID_YT8531,
+ .mask = PHY_ID_MASK,
+ .features = PHY_GBIT_FEATURES,
+ .probe = &yt8531_probe,
+ .config = &yt8531_config,
+ .startup = &yt8531_startup,
+ .shutdown = &genphy_shutdown,
+};
projects / u-boot.git / commitdiff