#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/meson-gxbb-gpio.h>
+#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
/ {
compatible = "amlogic,meson-gxbb";
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
+ reset: reset-controller@4404 {
+ compatible = "amlogic,meson-gxbb-reset";
+ reg = <0x0 0x04404 0x0 0x20>;
+ #reset-cells = <1>;
+ };
+
uart_A: serial@84c0 {
compatible = "amlogic,meson-uart";
- reg = <0x0 0x084c0 0x0 0x14>;
+ reg = <0x0 0x84c0 0x0 0x14>;
interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
clocks = <&xtal>;
status = "disabled";
};
+
+ uart_B: serial@84dc {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x84dc 0x0 0x14>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+
+ uart_C: serial@8700 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x8700 0x0 0x14>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
};
gic: interrupt-controller@c4301000 {
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
+ pinctrl_aobus: pinctrl@14 {
+ compatible = "amlogic,meson-gxbb-aobus-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio_ao: bank@14 {
+ reg = <0x0 0x00014 0x0 0x8>,
+ <0x0 0x0002c 0x0 0x4>,
+ <0x0 0x00024 0x0 0x8>;
+ reg-names = "mux", "pull", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ uart_ao_a_pins: uart_ao_a {
+ mux {
+ groups = "uart_tx_ao_a", "uart_rx_ao_a";
+ function = "uart_ao";
+ };
+ };
+ };
+
uart_AO: serial@4c0 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x004c0 0x0 0x14>;
};
};
+ periphs: periphs@c8834000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc8834000 0x0 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
+
+ rng {
+ compatible = "amlogic,meson-rng";
+ reg = <0x0 0x0 0x0 0x4>;
+ };
+
+ pinctrl_periphs: pinctrl@4b0 {
+ compatible = "amlogic,meson-gxbb-periphs-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio: bank@4b0 {
+ reg = <0x0 0x004b0 0x0 0x28>,
+ <0x0 0x004e8 0x0 0x14>,
+ <0x0 0x00120 0x0 0x14>,
+ <0x0 0x00430 0x0 0x40>;
+ reg-names = "mux", "pull", "pull-enable", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ emmc_pins: emmc {
+ mux {
+ groups = "emmc_nand_d07",
+ "emmc_cmd",
+ "emmc_clk";
+ function = "emmc";
+ };
+ };
+
+ sdcard_pins: sdcard {
+ mux {
+ groups = "sdcard_d0",
+ "sdcard_d1",
+ "sdcard_d2",
+ "sdcard_d3",
+ "sdcard_cmd",
+ "sdcard_clk";
+ function = "sdcard";
+ };
+ };
+
+ uart_a_pins: uart_a {
+ mux {
+ groups = "uart_tx_a",
+ "uart_rx_a";
+ function = "uart_a";
+ };
+ };
+
+ uart_b_pins: uart_b {
+ mux {
+ groups = "uart_tx_b",
+ "uart_rx_b";
+ function = "uart_b";
+ };
+ };
+
+ uart_c_pins: uart_c {
+ mux {
+ groups = "uart_tx_c",
+ "uart_rx_c";
+ function = "uart_c";
+ };
+ };
+
+ eth_pins: eth_c {
+ mux {
+ groups = "eth_mdio",
+ "eth_mdc",
+ "eth_clk_rx_clk",
+ "eth_rx_dv",
+ "eth_rxd0",
+ "eth_rxd1",
+ "eth_rxd2",
+ "eth_rxd3",
+ "eth_rgmii_tx_clk",
+ "eth_tx_en",
+ "eth_txd0",
+ "eth_txd1",
+ "eth_txd2",
+ "eth_txd3";
+ function = "eth";
+ };
+ };
+ };
+ };
+
+ hiubus: hiubus@c883c000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc883c000 0x0 0x2000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
+
+ clkc: clock-controller@0 {
+ compatible = "amlogic,gxbb-clkc";
+ #clock-cells = <1>;
+ reg = <0x0 0x0 0x0 0x3db>;
+ };
+ };
+
apb: apb@d0000000 {
compatible = "simple-bus";
reg = <0x0 0xd0000000 0x0 0x200000>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
};
+
+ ethmac: ethernet@c9410000 {
+ compatible = "amlogic,meson6-dwmac", "snps,dwmac";
+ reg = <0x0 0xc9410000 0x0 0x10000
+ 0x0 0xc8834540 0x0 0x4>;
+ interrupts = <0 8 1>;
+ interrupt-names = "macirq";
+ clocks = <&xtal>;
+ clock-names = "stmmaceth";
+ phy-mode = "rgmii";
+ status = "disabled";
+ };
};
};
--- /dev/null
+/*
+ * This file is provided under a dual BSD/GPLv2 license. When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * GPL LICENSE SUMMARY
+ *
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ * The full GNU General Public License is included in this distribution
+ * in the file called COPYING.
+ *
+ * BSD LICENSE
+ *
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Intel Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+#ifndef _DT_BINDINGS_AMLOGIC_MESON_GXBB_RESET_H
+#define _DT_BINDINGS_AMLOGIC_MESON_GXBB_RESET_H
+
+/* RESET0 */
+#define RESET_HIU 0
+/* 1 */
+#define RESET_DOS_RESET 2
+#define RESET_DDR_TOP 3
+#define RESET_DCU_RESET 4
+#define RESET_VIU 5
+#define RESET_AIU 6
+#define RESET_VID_PLL_DIV 7
+/* 8 */
+#define RESET_PMUX 9
+#define RESET_VENC 10
+#define RESET_ASSIST 11
+#define RESET_AFIFO2 12
+#define RESET_VCBUS 13
+/* 14 */
+/* 15 */
+#define RESET_GIC 16
+#define RESET_CAPB3_DECODE 17
+#define RESET_NAND_CAPB3 18
+#define RESET_HDMITX_CAPB3 19
+#define RESET_MALI_CAPB3 20
+#define RESET_DOS_CAPB3 21
+#define RESET_SYS_CPU_CAPB3 22
+#define RESET_CBUS_CAPB3 23
+#define RESET_AHB_CNTL 24
+#define RESET_AHB_DATA 25
+#define RESET_VCBUS_CLK81 26
+#define RESET_MMC 27
+#define RESET_MIPI_0 28
+#define RESET_MIPI_1 29
+#define RESET_MIPI_2 30
+#define RESET_MIPI_3 31
+/* RESET1 */
+#define RESET_CPPM 32
+#define RESET_DEMUX 33
+#define RESET_USB_OTG 34
+#define RESET_DDR 35
+#define RESET_AO_RESET 36
+#define RESET_BT656 37
+#define RESET_AHB_SRAM 38
+/* 39 */
+#define RESET_PARSER 40
+#define RESET_BLKMV 41
+#define RESET_ISA 42
+#define RESET_ETHERNET 43
+#define RESET_SD_EMMC_A 44
+#define RESET_SD_EMMC_B 45
+#define RESET_SD_EMMC_C 46
+#define RESET_ROM_BOOT 47
+#define RESET_SYS_CPU_0 48
+#define RESET_SYS_CPU_1 49
+#define RESET_SYS_CPU_2 50
+#define RESET_SYS_CPU_3 51
+#define RESET_SYS_CPU_CORE_0 52
+#define RESET_SYS_CPU_CORE_1 53
+#define RESET_SYS_CPU_CORE_2 54
+#define RESET_SYS_CPU_CORE_3 55
+#define RESET_SYS_PLL_DIV 56
+#define RESET_SYS_CPU_AXI 57
+#define RESET_SYS_CPU_L2 58
+#define RESET_SYS_CPU_P 59
+#define RESET_SYS_CPU_MBIST 60
+/* 61 */
+/* 62 */
+/* 63 */
+/* RESET2 */
+#define RESET_VD_RMEM 64
+#define RESET_AUDIN 65
+#define RESET_HDMI_TX 66
+/* 67 */
+/* 68 */
+/* 69 */
+#define RESET_GE2D 70
+#define RESET_PARSER_REG 71
+#define RESET_PARSER_FETCH 72
+#define RESET_PARSER_CTL 73
+#define RESET_PARSER_TOP 74
+/* 75 */
+/* 76 */
+#define RESET_AO_CPU_RESET 77
+#define RESET_MALI 78
+#define RESET_HDMI_SYSTEM_RESET 79
+/* 80-95 */
+/* RESET3 */
+#define RESET_RING_OSCILLATOR 96
+#define RESET_SYS_CPU 97
+#define RESET_EFUSE 98
+#define RESET_SYS_CPU_BVCI 99
+#define RESET_AIFIFO 100
+#define RESET_TVFE 101
+#define RESET_AHB_BRIDGE_CNTL 102
+/* 103 */
+#define RESET_AUDIO_DAC 104
+#define RESET_DEMUX_TOP 105
+#define RESET_DEMUX_DES 106
+#define RESET_DEMUX_S2P_0 107
+#define RESET_DEMUX_S2P_1 108
+#define RESET_DEMUX_RESET_0 109
+#define RESET_DEMUX_RESET_1 110
+#define RESET_DEMUX_RESET_2 111
+/* 112-127 */
+/* RESET4 */
+/* 128 */
+/* 129 */
+/* 130 */
+/* 131 */
+#define RESET_DVIN_RESET 132
+#define RESET_RDMA 133
+#define RESET_VENCI 134
+#define RESET_VENCP 135
+/* 136 */
+#define RESET_VDAC 137
+#define RESET_RTC 138
+/* 139 */
+#define RESET_VDI6 140
+#define RESET_VENCL 141
+#define RESET_I2C_MASTER_2 142
+#define RESET_I2C_MASTER_1 143
+/* 144-159 */
+/* RESET5 */
+/* 160-191 */
+/* RESET6 */
+#define RESET_PERIPHS_GENERAL 192
+#define RESET_PERIPHS_SPICC 193
+#define RESET_PERIPHS_SMART_CARD 194
+#define RESET_PERIPHS_SAR_ADC 195
+#define RESET_PERIPHS_I2C_MASTER_0 196
+#define RESET_SANA 197
+/* 198 */
+#define RESET_PERIPHS_STREAM_INTERFACE 199
+#define RESET_PERIPHS_SDIO 200
+#define RESET_PERIPHS_UART_0 201
+#define RESET_PERIPHS_UART_1_2 202
+#define RESET_PERIPHS_ASYNC_0 203
+#define RESET_PERIPHS_ASYNC_1 204
+#define RESET_PERIPHS_SPI_0 205
+#define RESET_PERIPHS_SDHC 206
+#define RESET_UART_SLIP 207
+/* 208-223 */
+/* RESET7 */
+#define RESET_USB_DDR_0 224
+#define RESET_USB_DDR_1 225
+#define RESET_USB_DDR_2 226
+#define RESET_USB_DDR_3 227
+/* 228 */
+#define RESET_DEVICE_MMC_ARB 229
+/* 230 */
+#define RESET_VID_LOCK 231
+#define RESET_A9_DMC_PIPEL 232
+/* 233-255 */
+
+#endif
projects / u-boot.git / commitdiff