Changes for U-Boot 1.1.4:
======================================================================
+* Add support for TQM8541/8555 boards, TQM85xx support reworked:
+ - Support for TQM8541/8555 boards added.
+ - Complete rework of TQM8540/8560 support.
+ - Common TQM85xx code now supports all current TQM85xx platforms
+ (TQM8540/8541/8555/8560).
+ - DDR SDRAM size detection added.
+ - CAS latency default values can be overwritten by setting "serial#"
+ to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used.
+ If problems are detected with this non default CAS latency,
+ the defualt values will be used instead.
+ - FLASH size detection added.
+ - Moved FCC ethernet driver initialization behind TSEC driver init
+ -> TSEC is first device.
+ Patch by Stefan Roese, 30 Nov 2005
+
* Add support for AMCC 440SP, add support for AMCC Luan 440SP eval board.
Patch by John Otken, 23 Nov 2005
Stefan Roese <sr@denx.de>
+ uc100 MPC857
+
+ TQM85xx MPC8540/8541/8555/8560
+
bamboo PPC440EP
bunbinga PPC405EP
ebony PPC440GP
ocotea PPC440GX
+ p3p440 PPC440GP
sycamore PPC405GPr
walnut PPC405GP
yellowstone PPC440GR
MPC8540ADS MPC8540EVAL MPC8541CDS MPC8548CDS \
MPC8555CDS MPC8560ADS PM854 PM856 \
sbc8540 sbc8560 stxgp3 TQM8540 \
- TQM8560 \
+ TQM8541 TQM8555 TQM8560 \
"
#########################################################################
stxgp3_config: unconfig
@./mkconfig $(@:_config=) ppc mpc85xx stxgp3
-TQM8540_config: unconfig
- @./mkconfig $(@:_config=) ppc mpc85xx tqm8540
-
-TQM8560_config: unconfig
- @./mkconfig $(@:_config=) ppc mpc85xx tqm8560
+TQM8540_config \
+TQM8541_config \
+TQM8555_config \
+TQM8560_config: unconfig
+ @case "$@" in \
+ TQM8540_config) CTYPE=8540;; \
+ TQM8541_config) CTYPE=8541;; \
+ TQM8555_config) CTYPE=8555;; \
+ TQM8560_config) CTYPE=8560;; \
+ esac; \
+ >include/config.h ; \
+ echo "... TQM"$${CTYPE}; \
+ echo "#define CONFIG_MPC$${CTYPE}">>include/config.h; \
+ echo "#define CONFIG_TQM$${CTYPE}">>include/config.h; \
+ echo "#define CONFIG_HOSTNAME tqm$${CTYPE}">>include/config.h; \
+ echo "#define CONFIG_BOARDNAME \"TQM$${CTYPE}\"">>include/config.h; \
+ echo "#define CFG_BOOTFILE \"bootfile=/tftpboot/tqm$${CTYPE}/uImage\0\"">>include/config.h
+ @./mkconfig -a TQM85xx ppc mpc85xx tqm85xx
#########################################################################
## 74xx/7xx Systems
+++ /dev/null
-/*
- * Copyright 2004 Freescale Semiconductor.
- * Copyright (C) 2002,2003, Motorola Inc.
- * Xianghua Xiao <X.Xiao@motorola.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-#include <asm/cache.h>
-#include <asm/mmu.h>
-#include <config.h>
-#include <mpc85xx.h>
-
-
-/*
- * TLB0 and TLB1 Entries
- *
- * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
- * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
- * these TLB entries are established.
- *
- * The TLB entries for DDR are dynamically setup in spd_sdram()
- * and use TLB1 Entries 8 through 15 as needed according to the
- * size of DDR memory.
- *
- * MAS0: tlbsel, esel, nv
- * MAS1: valid, iprot, tid, ts, tsize
- * MAS2: epn, sharen, x0, x1, w, i, m, g, e
- * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
- */
-
-#define entry_start \
- mflr r1 ; \
- bl 0f ;
-
-#define entry_end \
-0: mflr r0 ; \
- mtlr r1 ; \
- blr ;
-
-
- .section .bootpg, "ax"
- .globl tlb1_entry
-tlb1_entry:
- entry_start
-
- /*
- * Number of TLB0 and TLB1 entries in the following table
- */
- .long 13
-
- /*
- * TLB0 16K Cacheable, non-guarded
- * 0xd001_0000 16K Temporary Global data for initialization
- *
- * Use four 4K TLB0 entries. These entries must be cacheable
- * as they provide the bootstrap memory before the memory
- * controler and real memory have been configured.
- *
- * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
- * and must not collide with other TLB0 entries.
- */
- .long TLB1_MAS0(0, 0, 0)
- .long TLB1_MAS1(1, 0, 0, 0, 0)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),
- 0,0,0,0,0,0,0,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),
- 0,0,0,0,0,1,0,1,0,1)
-
- .long TLB1_MAS0(0, 0, 0)
- .long TLB1_MAS1(1, 0, 0, 0, 0)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
- 0,0,0,0,0,0,0,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
- 0,0,0,0,0,1,0,1,0,1)
-
- .long TLB1_MAS0(0, 0, 0)
- .long TLB1_MAS1(1, 0, 0, 0, 0)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
- 0,0,0,0,0,0,0,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024),
- 0,0,0,0,0,1,0,1,0,1)
-
- .long TLB1_MAS0(0, 0, 0)
- .long TLB1_MAS1(1, 0, 0, 0, 0)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
- 0,0,0,0,0,0,0,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
- 0,0,0,0,0,1,0,1,0,1)
-
-
- /*
- * TLB 0, 1: 32M Non-cacheable, guarded
- * 0xfe000000 32M FLASH
- * Out of reset this entry is only 4K.
- */
- .long TLB1_MAS0(1, 1, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
- .long TLB1_MAS0(1, 0, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE+0x1000000), 0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE+0x1000000), 0,0,0,0,0,1,0,1,0,1)
-
- /*
- * TLB 2: 256M Non-cacheable, guarded
- * 0x80000000 256M PCI1 MEM First half
- */
- .long TLB1_MAS0(1, 2, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
-
- /*
- * TLB 3: 256M Non-cacheable, guarded
- * 0x90000000 256M PCI1 MEM Second half
- */
- .long TLB1_MAS0(1, 3, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000),
- 0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000),
- 0,0,0,0,0,1,0,1,0,1)
-
- /*
- * TLB 4: 256M Non-cacheable, guarded
- * 0xc0000000 256M Rapid IO MEM First half
- */
- .long TLB1_MAS0(1, 4, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
-
- /*
- * TLB 5: 256M Non-cacheable, guarded
- * 0xd0000000 256M Rapid IO MEM Second half
- */
- .long TLB1_MAS0(1, 5, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000),
- 0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000),
- 0,0,0,0,0,1,0,1,0,1)
-
- /*
- * TLB 6: 64M Non-cacheable, guarded
- * 0xe000_0000 1M CCSRBAR
- * 0xe200_0000 16M PCI1 IO
- */
- .long TLB1_MAS0(1, 6, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
-
-#if !defined(CONFIG_SPD_EEPROM)
- /*
- * TLB 7: 256M DDR
- * 0x00000000 256M DDR System memory
- * Without SPD EEPROM configured DDR, this must be setup manually.
- * Make sure the TLB count at the top of this table is correct.
- * Likely it needs to be increased by two for these entries.
- */
- .long TLB1_MAS0(1, 7, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,0,0,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
- .long TLB1_MAS0(1, 8, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,0,0,0,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,0,1,0,1,0,1)
-#endif
-
- entry_end
-
-/*
- * LAW(Local Access Window) configuration:
- *
- * 0x0000_0000 0x7fff_ffff DDR 2G
- * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M
- * 0xc000_0000 0xdfff_ffff RapidIO 512M
- * 0xe000_0000 0xe000_ffff CCSR 1M
- * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M
- * 0xf800_0000 0xf80f_ffff BCSR 1M
- * 0xfe00_0000 0xffff_ffff FLASH (boot bank) 32M
- *
- * Notes:
- * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- * If flash is 8M at default position (last 8M), no LAW needed.
- */
-
-#if !defined(CONFIG_SPD_EEPROM)
-#define LAWBAR0 ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff)
-#define LAWAR0 (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_256M))
-#else
-#define LAWBAR0 0
-#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
-#endif
-
-#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
-#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M))
-
-#define LAWBAR2 ((CFG_LBC_FLASH_BASE>>12) & 0xfffff)
-#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_32M))
-
-#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
-#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M))
-
-/*
- * Rapid IO at 0xc000_0000 for 512 M
- */
-#define LAWBAR4 ((CFG_RIO_MEM_BASE>>12) & 0xfffff)
-#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M))
-
-
- .section .bootpg, "ax"
- .globl law_entry
-law_entry:
- entry_start
- .long 0x05
- .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
- .long LAWBAR4,LAWAR4
- entry_end
+++ /dev/null
-/*
- * Copyright 2005 DENX Software Engineering
- * Copyright 2004 Freescale Semiconductor.
- * (C) Copyright 2002,2003, Motorola Inc.
- * Xianghua Xiao, (X.Xiao@motorola.com)
- *
- * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-
-#include <common.h>
-#include <pci.h>
-#include <asm/processor.h>
-#include <asm/immap_85xx.h>
-#include <spd.h>
-
-#if defined(CONFIG_DDR_ECC)
-extern void ddr_enable_ecc (unsigned int dram_size);
-#endif
-
-extern long int spd_sdram (void);
-
-void local_bus_init (void);
-long int fixed_sdram (void);
-
-
-int board_early_init_f (void)
-{
- return 0;
-}
-
-int checkboard (void)
-{
- puts ("Board: TQM8540\n");
-
-#ifdef CONFIG_PCI
- printf ("PCI1: 32 bit, %d MHz (compiled)\n",
- CONFIG_SYS_CLK_FREQ / 1000000);
-#else
- printf ("PCI1: disabled\n");
-#endif
- /*
- * Initialize local bus.
- */
- local_bus_init ();
-
- return 0;
-}
-
-
-long int initdram (int board_type)
-{
- long dram_size = 0;
- extern long spd_sdram (void);
- volatile immap_t *immap = (immap_t *) CFG_IMMR;
-
-#if defined(CONFIG_DDR_DLL)
- {
- volatile ccsr_gur_t *gur= &immap->im_gur;
- int i,x;
-
- x = 10;
-
- /*
- * Work around to stabilize DDR DLL
- */
- gur->ddrdllcr = 0x81000000;
- asm("sync;isync;msync");
- udelay (200);
- while (gur->ddrdllcr != 0x81000100) {
- gur->devdisr = gur->devdisr | 0x00010000;
- asm("sync;isync;msync");
- for (i=0; i<x; i++)
- ;
- gur->devdisr = gur->devdisr & 0xfff7ffff;
- asm("sync;isync;msync");
- x++;
- }
- }
-#endif
-
-#if defined(CONFIG_SPD_EEPROM)
- dram_size = spd_sdram ();
-#else
- dram_size = fixed_sdram ();
-#endif
-
-#if defined(CONFIG_DDR_ECC)
- /*
- * Initialize and enable DDR ECC.
- */
- ddr_enable_ecc (dram_size);
-#endif
-
- return dram_size;
-}
-
-
-/*
- * Initialize Local Bus
- */
-
-void local_bus_init (void)
-{
- volatile immap_t *immap = (immap_t *) CFG_IMMR;
- volatile ccsr_gur_t *gur = &immap->im_gur;
- volatile ccsr_lbc_t *lbc = &immap->im_lbc;
-
- uint clkdiv;
- uint lbc_hz;
- sys_info_t sysinfo;
-
- /*
- * Errata LBC11.
- * Fix Local Bus clock glitch when DLL is enabled.
- *
- * If localbus freq is < 66Mhz, DLL bypass mode must be used.
- * If localbus freq is > 133Mhz, DLL can be safely enabled.
- * Between 66 and 133, the DLL is enabled with an override workaround.
- */
-
- get_sys_info (&sysinfo);
- clkdiv = lbc->lcrr & 0x0f;
- lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
-
- if (lbc_hz < 66) {
- lbc->lcrr = CFG_LBC_LCRR | 0x80000000; /* DLL Bypass */
- lbc->ltedr = 0xa4c80000; /* DK: !!! */
-
- } else if (lbc_hz >= 133) {
- lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */
-
- } else {
- /*
- * On REV1 boards, need to change CLKDIV before enable DLL.
- * Default CLKDIV is 8, change it to 4 temporarily.
- */
- uint pvr = get_pvr ();
- uint temp_lbcdll = 0;
-
- if (pvr == PVR_85xx_REV1) {
- /* FIXME: Justify the high bit here. */
- lbc->lcrr = 0x10000004;
- }
-
- lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */
- udelay (200);
-
- /*
- * Sample LBC DLL ctrl reg, upshift it to set the
- * override bits.
- */
- temp_lbcdll = gur->lbcdllcr;
- gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
- asm ("sync;isync;msync");
- }
-}
-
-
-#if defined(CFG_DRAM_TEST)
-int testdram (void)
-{
- uint *pstart = (uint *) CFG_MEMTEST_START;
- uint *pend = (uint *) CFG_MEMTEST_END;
- uint *p;
-
- printf ("SDRAM test phase 1:\n");
- for (p = pstart; p < pend; p++)
- *p = 0xaaaaaaaa;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- printf ("SDRAM test phase 2:\n");
- for (p = pstart; p < pend; p++)
- *p = 0x55555555;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- printf ("SDRAM test passed.\n");
- return 0;
-}
-#endif
-
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*************************************************************************
- * fixed sdram init -- doesn't use serial presence detect.
- ************************************************************************/
-long int fixed_sdram (void)
-{
-#ifndef CFG_RAMBOOT
- volatile immap_t *immap = (immap_t *) CFG_IMMR;
- volatile ccsr_ddr_t *ddr = &immap->im_ddr;
-
- ddr->cs0_bnds = CFG_DDR_CS0_BNDS;
- ddr->cs0_config = CFG_DDR_CS0_CONFIG;
- ddr->timing_cfg_1 = CFG_DDR_TIMING_1;
- ddr->timing_cfg_2 = CFG_DDR_TIMING_2;
- ddr->sdram_mode = CFG_DDR_MODE;
- ddr->sdram_interval = CFG_DDR_INTERVAL;
- ddr->err_disable = 0x0000000D;
-#if defined (CONFIG_DDR_ECC)
- ddr->err_disable = 0x0000000D;
- ddr->err_sbe = 0x00ff0000;
-#endif
- asm ("sync;isync;msync");
- udelay (500);
-#if defined (CONFIG_DDR_ECC)
- /* Enable ECC checking */
- ddr->sdram_cfg = (CFG_DDR_CONTROL | 0x20000000);
-#else
- ddr->sdram_cfg = CFG_DDR_CONTROL;
-#endif
- asm ("sync; isync; msync");
- udelay (500);
-#endif
- return get_ram_size (0, CFG_SDRAM_SIZE * 1024 * 1024);
-}
-#endif /* !defined(CONFIG_SPD_EEPROM) */
-
-
-#if defined(CONFIG_PCI)
-/*
- * Initialize PCI Devices, report devices found.
- */
-
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_mpc85xxads_config_table[] = {
- {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
- PCI_IDSEL_NUMBER, PCI_ANY_ID,
- pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_MEMORY |
- PCI_COMMAND_MASTER}},
- {}
-};
-#endif
-
-
-static struct pci_controller hose = {
-#ifndef CONFIG_PCI_PNP
- config_table:pci_mpc85xxads_config_table,
-#endif
-};
-
-#endif /* CONFIG_PCI */
-
-
-void pci_init_board (void)
-{
-#ifdef CONFIG_PCI
- extern void pci_mpc85xx_init (struct pci_controller *hose);
-
- pci_mpc85xx_init (&hose);
-#endif /* CONFIG_PCI */
-}
+++ /dev/null
-#
-# (C) Copyright 2001
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = lib$(BOARD).a
-
-OBJS := $(BOARD).o
-SOBJS := init.o
-#SOBJS :=
-
-$(LIB): $(OBJS) $(SOBJS)
- $(AR) crv $@ $(OBJS)
-
-clean:
- rm -f $(OBJS) $(SOBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak .depend
-
-#########################################################################
-
-.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
- $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
-
--include .depend
-
-#########################################################################
+++ /dev/null
-# Copyright 2004 Freescale Semiconductor.
-# Modified by Xianghua Xiao, X.Xiao@motorola.com
-# (C) Copyright 2002,Motorola Inc.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-#
-# tqm8560 board
-# default CCARBAR is at 0xff700000
-# assume U-Boot is less than 256k
-#
-TEXT_BASE = 0xfffc0000
+++ /dev/null
-/*
- * (C) Copyright 2002,2003, Motorola,Inc.
- * Xianghua Xiao, X.Xiao@motorola.com.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-OUTPUT_ARCH(powerpc)
-SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- .resetvec 0xFFFFFFFC :
- {
- *(.resetvec)
- } = 0xffff
-
- .bootpg 0xFFFFF000 :
- {
- cpu/mpc85xx/start.o (.bootpg)
- board/tqm8560/init.o (.bootpg)
- } = 0xffff
-
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- cpu/mpc85xx/start.o (.text)
- board/tqm8560/init.o (.text)
- cpu/mpc85xx/traps.o (.text)
- cpu/mpc85xx/interrupts.o (.text)
- cpu/mpc85xx/cpu_init.o (.text)
- cpu/mpc85xx/cpu.o (.text)
- cpu/mpc85xx/speed.o (.text)
- cpu/mpc85xx/pci.o (.text)
- common/dlmalloc.o (.text)
- lib_generic/crc32.o (.text)
- lib_ppc/extable.o (.text)
- lib_generic/zlib.o (.text)
- *(.text)
- *(.fixup)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(.rodata)
- *(.rodata1)
- *(.rodata.str1.4)
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
- __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
- __u_boot_cmd_start = .;
- .u_boot_cmd : { *(.u_boot_cmd) }
- __u_boot_cmd_end = .;
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
- _end = . ;
- PROVIDE (end = .);
-}
LIB = lib$(BOARD).a
-OBJS := $(BOARD).o
+OBJS := $(BOARD).o sdram.o
SOBJS := init.o
#SOBJS :=
#
#
-# tqm8540 board
+# tqm85xx board
# default CCARBAR is at 0xff700000
# assume U-Boot is less than 256k
#
/*
- * TLB 0, 1: 32M Non-cacheable, guarded
- * 0xfe000000 32M FLASH
+ * TLB 0, 1: 128M Non-cacheable, guarded
+ * 0xf8000000 128M FLASH
* Out of reset this entry is only 4K.
*/
.long TLB1_MAS0(1, 1, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(1, 0, 0)
- .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE+0x1000000), 0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE+0x1000000), 0,0,0,0,0,1,0,1,0,1)
+ .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE+0x4000000), 0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE+0x4000000), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 2: 256M Non-cacheable, guarded
.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
-#if !defined(CONFIG_SPD_EEPROM)
/*
- * TLB 7: 256M DDR
- * 0x00000000 256M DDR System memory
+ * TLB 7+8: 512M DDR, cache disabled (needed for memory test)
+ * 0x00000000 512M DDR System memory
* Without SPD EEPROM configured DDR, this must be setup manually.
* Make sure the TLB count at the top of this table is correct.
* Likely it needs to be increased by two for these entries.
*/
.long TLB1_MAS0(1, 7, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(1, 8, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,0,0,0,0)
+ .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,0,1,0,1,0,1)
-#endif
entry_end
* If flash is 8M at default position (last 8M), no LAW needed.
*/
-#if !defined(CONFIG_SPD_EEPROM)
#define LAWBAR0 ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff)
-#define LAWAR0 (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_256M))
-#else
-#define LAWBAR0 0
-#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
-#endif
+#define LAWAR0 (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_512M))
#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M))
#define LAWBAR2 ((CFG_LBC_FLASH_BASE>>12) & 0xfffff)
-#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_32M))
+#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_128M))
#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M))
--- /dev/null
+/*
+ * (C) Copyright 2005
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <spd.h>
+
+struct sdram_conf_s {
+ unsigned long size;
+ unsigned long reg;
+};
+
+typedef struct sdram_conf_s sdram_conf_t;
+
+sdram_conf_t ddr_cs_conf[] = {
+ {(512 << 20), 0x80000202}, /* 512MB, 14x10(4) */
+ {(256 << 20), 0x80000102}, /* 256MB, 13x10(4) */
+ {(128 << 20), 0x80000101}, /* 128MB, 13x9(4) */
+ {(64 << 20), 0x80000001}, /* 64MB, 12x9(4) */
+};
+
+#define N_DDR_CS_CONF (sizeof(ddr_cs_conf) / sizeof(ddr_cs_conf[0]))
+
+int cas_latency(void);
+
+/*
+ * Autodetect onboard DDR SDRAM on 85xx platforms
+ *
+ * NOTE: Some of the hardcoded values are hardware dependant,
+ * so this should be extended for other future boards
+ * using this routine!
+ */
+long int sdram_setup(int casl)
+{
+ int i;
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile ccsr_ddr_t *ddr = &immap->im_ddr;
+ unsigned long cfg_ddr_timing1;
+ unsigned long cfg_ddr_mode;
+
+ /*
+ * Disable memory controller.
+ */
+ ddr->cs0_config = 0;
+ ddr->sdram_cfg = 0;
+
+ switch (casl) {
+ case 20:
+ cfg_ddr_timing1 = 0x47405331 | (3 << 16);
+ cfg_ddr_mode = 0x40020002 | (2 << 4);
+ break;
+
+ case 25:
+ cfg_ddr_timing1 = 0x47405331 | (4 << 16);
+ cfg_ddr_mode = 0x40020002 | (6 << 4);
+ break;
+
+ case 30:
+ default:
+ cfg_ddr_timing1 = 0x47405331 | (5 << 16);
+ cfg_ddr_mode = 0x40020002 | (3 << 4);
+ break;
+ }
+
+ ddr->cs0_bnds = (ddr_cs_conf[0].size - 1) >> 24;
+ ddr->cs0_config = ddr_cs_conf[0].reg;
+ ddr->timing_cfg_1 = cfg_ddr_timing1;
+ ddr->timing_cfg_2 = 0x00000800; /* P9-45,may need tuning */
+ ddr->sdram_mode = cfg_ddr_mode;
+ ddr->sdram_interval = 0x05160100; /* autocharge,no open page */
+ ddr->err_disable = 0x0000000D;
+
+ asm ("sync;isync;msync");
+ udelay(1000);
+
+ ddr->sdram_cfg = 0xc2000000; /* unbuffered,no DYN_PWR */
+ asm ("sync; isync; msync");
+ udelay(1000);
+
+ for (i=0; i<N_DDR_CS_CONF; i++) {
+ ddr->cs0_config = ddr_cs_conf[i].reg;
+
+ if (get_ram_size(0, ddr_cs_conf[i].size) == ddr_cs_conf[i].size) {
+ /*
+ * OK, size detected -> all done
+ */
+ return ddr_cs_conf[i].size;
+ }
+ }
+
+ return 0; /* nothing found ! */
+}
+
+void board_add_ram_info(int use_default)
+{
+ int casl;
+
+ if (use_default)
+ casl = CONFIG_DDR_DEFAULT_CL;
+ else
+ casl = cas_latency();
+
+ puts(" (CL=");
+ switch (casl) {
+ case 20:
+ puts("2)");
+ break;
+
+ case 25:
+ puts("2.5)");
+ break;
+
+ case 30:
+ puts("3)");
+ break;
+ }
+}
+
+long int initdram (int board_type)
+{
+ long dram_size = 0;
+ int casl;
+
+#if defined(CONFIG_DDR_DLL)
+ /*
+ * This DLL-Override only used on TQM8540 and TQM8560
+ */
+ {
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile ccsr_gur_t *gur= &immap->im_gur;
+ int i,x;
+
+ x = 10;
+
+ /*
+ * Work around to stabilize DDR DLL
+ */
+ gur->ddrdllcr = 0x81000000;
+ asm("sync;isync;msync");
+ udelay (200);
+ while (gur->ddrdllcr != 0x81000100) {
+ gur->devdisr = gur->devdisr | 0x00010000;
+ asm("sync;isync;msync");
+ for (i=0; i<x; i++)
+ ;
+ gur->devdisr = gur->devdisr & 0xfff7ffff;
+ asm("sync;isync;msync");
+ x++;
+ }
+ }
+#endif
+
+ casl = cas_latency();
+ dram_size = sdram_setup(casl);
+ if ((dram_size == 0) && (casl != CONFIG_DDR_DEFAULT_CL)) {
+ /*
+ * Try again with default CAS latency
+ */
+ puts("Problem with CAS lantency");
+ board_add_ram_info(1);
+ puts(", using default CL!\n");
+ casl = CONFIG_DDR_DEFAULT_CL;
+ dram_size = sdram_setup(casl);
+ puts(" ");
+ }
+
+ return dram_size;
+}
+
+#if defined(CFG_DRAM_TEST)
+int testdram (void)
+{
+ uint *pstart = (uint *) CFG_MEMTEST_START;
+ uint *pend = (uint *) CFG_MEMTEST_END;
+ uint *p;
+
+ printf ("SDRAM test phase 1:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0xaaaaaaaa;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0xaaaaaaaa) {
+ printf ("SDRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ printf ("SDRAM test phase 2:\n");
+ for (p = pstart; p < pend; p++)
+ *p = 0x55555555;
+
+ for (p = pstart; p < pend; p++) {
+ if (*p != 0x55555555) {
+ printf ("SDRAM test fails at: %08x\n", (uint) p);
+ return 1;
+ }
+ }
+
+ printf ("SDRAM test passed.\n");
+ return 0;
+}
+#endif
/*
- * Copyright 2005 DENX Software Engineering
+ * (C) Copyright 2005
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
* Copyright 2004 Freescale Semiconductor.
* (C) Copyright 2002,2003, Motorola Inc.
* Xianghua Xiao, (X.Xiao@motorola.com)
#include <asm/immap_85xx.h>
#include <ioports.h>
#include <spd.h>
+#include <flash.h>
-#if defined(CONFIG_DDR_ECC)
-extern void ddr_enable_ecc (unsigned int dram_size);
-#endif
-
-extern long int spd_sdram (void);
+extern flash_info_t flash_info[]; /* FLASH chips info */
void local_bus_init (void);
long int fixed_sdram (void);
+ulong flash_get_size (ulong base, int banknum);
+#ifdef CONFIG_CPM2
/*
* I/O Port configuration table
*
/* Port A configuration */
{ /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */
- /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */
- /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */
- /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */
- /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */
- /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */
+ /* PA31 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII COL */
+ /* PA30 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII CRS */
+ /* PA29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_ER */
+ /* PA28 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_EN */
+ /* PA27 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_DV */
+ /* PA26 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_ER */
/* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */
/* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */
/* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */
/* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */
- /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */
- /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */
- /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */
- /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */
- /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
- /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
- /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
- /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
+ /* PA21 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[3] */
+ /* PA20 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[2] */
+ /* PA19 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[1] */
+ /* PA18 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[0] */
+ /* PA17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[0] */
+ /* PA16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[1] */
+ /* PA15 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[2] */
+ /* PA14 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[3] */
/* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
/* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
/* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
/* Port B configuration */
{ /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
- /* PB30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
- /* PB29 */ { 0, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
- /* PB28 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
- /* PB27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
- /* PB26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
- /* PB25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
- /* PB24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
- /* PB23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
- /* PB22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
- /* PB21 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
- /* PB20 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
- /* PB19 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
- /* PB18 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
+ /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
+ /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
+ /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
+ /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
+ /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
+ /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
+ /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
+ /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
+ /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
+ /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
+ /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
+ /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
+ /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
+ /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
/* PB17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
/* PB16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
/* PB15 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
/* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */
/* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */
/* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */
- /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
- /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
- /* PC19 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */
+ /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
+ /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
+ /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */
/* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */
/* PC17 */ { 1, 1, 0, 0, 0, 0 }, /* PC17 */
- /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */
+ /* PC16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */
/* PC15 */ { 0, 1, 0, 0, 0, 0 }, /* PC15 */
/* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */
/* PC13 */ { 0, 1, 0, 0, 0, 0 }, /* PC13 */
/* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
}
};
+#endif /* CONFIG_CPM2 */
+
+#define CASL_STRING1 "casl=xx"
+#define CASL_STRING2 "casl="
+static const int casl_table[] = { 20, 25, 30 };
+#define N_CASL (sizeof(casl_table) / sizeof(casl_table[0]))
-int board_early_init_f (void)
+int cas_latency(void)
{
- return 0;
+ char *s = getenv("serial#");
+ int casl;
+ int val;
+ int i;
+
+ casl = CONFIG_DDR_DEFAULT_CL;
+
+ if (s != NULL) {
+ if (strncmp(s + strlen(s) - strlen(CASL_STRING1), CASL_STRING2,
+ strlen(CASL_STRING2)) == 0) {
+ val = simple_strtoul(s + strlen(s) - 2, NULL, 10);
+
+ for (i=0; i<N_CASL; ++i) {
+ if (val == casl_table[i]) {
+ return val;
+ }
+ }
+ }
+ }
+
+ return casl;
}
int checkboard (void)
{
- puts ("Board: TQM8560\n");
+ char *s = getenv("serial#");
+
+ printf("Board: %s", CONFIG_BOARDNAME);
+ if (s != NULL) {
+ puts(", serial# ");
+ puts(s);
+ }
+ putc('\n');
#ifdef CONFIG_PCI
printf ("PCI1: 32 bit, %d MHz (compiled)\n",
#else
printf ("PCI1: disabled\n");
#endif
+
/*
* Initialize local bus.
*/
return 0;
}
-
-long int initdram (int board_type)
+int misc_init_r (void)
{
- long dram_size = 0;
- extern long spd_sdram (void);
- volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ DECLARE_GLOBAL_DATA_PTR;
+ volatile immap_t *immap = (immap_t *)CFG_IMMR;
+ volatile ccsr_lbc_t *memctl = &immap->im_lbc;
-#if defined(CONFIG_DDR_DLL)
- {
- volatile ccsr_gur_t *gur= &immap->im_gur;
- int i,x;
+ /*
+ * Adjust flash start and offset to detected values
+ */
+ gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
+ gd->bd->bi_flashoffset = 0;
- x = 10;
+ /*
+ * Check if boot FLASH isn't max size
+ */
+ if (gd->bd->bi_flashsize < (0 - CFG_FLASH0)) {
+ memctl->or0 = gd->bd->bi_flashstart | (CFG_OR0_PRELIM & 0x00007fff);
+ memctl->br0 = gd->bd->bi_flashstart | (CFG_BR0_PRELIM & 0x00007fff);
/*
- * Work around to stabilize DDR DLL
+ * Re-check to get correct base address
*/
- gur->ddrdllcr = 0x81000000;
- asm("sync;isync;msync");
- udelay (200);
- while (gur->ddrdllcr != 0x81000100) {
- gur->devdisr = gur->devdisr | 0x00010000;
- asm("sync;isync;msync");
- for (i=0; i<x; i++)
- ;
- gur->devdisr = gur->devdisr & 0xfff7ffff;
- asm("sync;isync;msync");
- x++;
- }
+ flash_get_size(gd->bd->bi_flashstart, CFG_MAX_FLASH_BANKS - 1);
}
-#endif
-#if defined(CONFIG_SPD_EEPROM)
- dram_size = spd_sdram ();
-#else
- dram_size = fixed_sdram ();
-#endif
-
-#if defined(CONFIG_DDR_ECC)
/*
- * Initialize and enable DDR ECC.
+ * Check if only one FLASH bank is available
*/
- ddr_enable_ecc (dram_size);
-#endif
+ if (gd->bd->bi_flashsize != CFG_MAX_FLASH_BANKS * (0 - CFG_FLASH0)) {
+ memctl->or1 = 0;
+ memctl->br1 = 0;
- return dram_size;
-}
+ /*
+ * Re-do flash protection upon new addresses
+ */
+ flash_protect (FLAG_PROTECT_CLEAR,
+ gd->bd->bi_flashstart, 0xffffffff,
+ &flash_info[CFG_MAX_FLASH_BANKS - 1]);
+
+ /* Monitor protection ON by default */
+ flash_protect (FLAG_PROTECT_SET,
+ CFG_MONITOR_BASE, 0xffffffff,
+ &flash_info[CFG_MAX_FLASH_BANKS - 1]);
+
+ /* Environment protection ON by default */
+ flash_protect (FLAG_PROTECT_SET,
+ CFG_ENV_ADDR,
+ CFG_ENV_ADDR + CFG_ENV_SECT_SIZE - 1,
+ &flash_info[CFG_MAX_FLASH_BANKS - 1]);
+
+ /* Redundant environment protection ON by default */
+ flash_protect (FLAG_PROTECT_SET,
+ CFG_ENV_ADDR_REDUND,
+ CFG_ENV_ADDR_REDUND + CFG_ENV_SIZE_REDUND - 1,
+ &flash_info[CFG_MAX_FLASH_BANKS - 1]);
+ }
+ return 0;
+}
/*
* Initialize Local Bus
*/
-
void local_bus_init (void)
{
volatile immap_t *immap = (immap_t *) CFG_IMMR;
}
}
-
-#if defined(CFG_DRAM_TEST)
-int testdram (void)
-{
- uint *pstart = (uint *) CFG_MEMTEST_START;
- uint *pend = (uint *) CFG_MEMTEST_END;
- uint *p;
-
- printf ("SDRAM test phase 1:\n");
- for (p = pstart; p < pend; p++)
- *p = 0xaaaaaaaa;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0xaaaaaaaa) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- printf ("SDRAM test phase 2:\n");
- for (p = pstart; p < pend; p++)
- *p = 0x55555555;
-
- for (p = pstart; p < pend; p++) {
- if (*p != 0x55555555) {
- printf ("SDRAM test fails at: %08x\n", (uint) p);
- return 1;
- }
- }
-
- printf ("SDRAM test passed.\n");
- return 0;
-}
-#endif
-
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*************************************************************************
- * fixed sdram init -- doesn't use serial presence detect.
- ************************************************************************/
-long int fixed_sdram (void)
-{
-#ifndef CFG_RAMBOOT
- volatile immap_t *immap = (immap_t *) CFG_IMMR;
- volatile ccsr_ddr_t *ddr = &immap->im_ddr;
-
- ddr->cs0_bnds = CFG_DDR_CS0_BNDS;
- ddr->cs0_config = CFG_DDR_CS0_CONFIG;
- ddr->timing_cfg_1 = CFG_DDR_TIMING_1;
- ddr->timing_cfg_2 = CFG_DDR_TIMING_2;
- ddr->sdram_mode = CFG_DDR_MODE;
- ddr->sdram_interval = CFG_DDR_INTERVAL;
- ddr->err_disable = 0x0000000D;
-#if defined (CONFIG_DDR_ECC)
- ddr->err_disable = 0x0000000D;
- ddr->err_sbe = 0x00ff0000;
-#endif
- asm ("sync;isync;msync");
- udelay (500);
-#if defined (CONFIG_DDR_ECC)
- /* Enable ECC checking */
- ddr->sdram_cfg = (CFG_DDR_CONTROL | 0x20000000);
-#else
- ddr->sdram_cfg = CFG_DDR_CONTROL;
-#endif
- asm ("sync; isync; msync");
- udelay (500);
-#endif
- return get_ram_size (0, CFG_SDRAM_SIZE * 1024 * 1024);
-}
-#endif /* !defined(CONFIG_SPD_EEPROM) */
-
-
#if defined(CONFIG_PCI)
/*
* Initialize PCI Devices, report devices found.
.bootpg 0xFFFFF000 :
{
cpu/mpc85xx/start.o (.bootpg)
- board/tqm8540/init.o (.bootpg)
+ board/tqm85xx/init.o (.bootpg)
} = 0xffff
/* Read-only sections, merged into text segment: */
.text :
{
cpu/mpc85xx/start.o (.text)
- board/tqm8540/init.o (.text)
+ board/tqm85xx/init.o (.text)
cpu/mpc85xx/traps.o (.text)
cpu/mpc85xx/interrupts.o (.text)
cpu/mpc85xx/cpu_init.o (.text)
+++ /dev/null
-/*
- * Copyright 2005 DENX Software Engineering
- * Wolfgang Denk <wd@denx.de>
- * Copyright 2004 Freescale Semiconductor.
- * (C) Copyright 2002,2003 Motorola,Inc.
- * Xianghua Xiao <X.Xiao@motorola.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * TQM8540 board configuration file
- *
- * Make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC8540 1 /* MPC8540 specific */
-#define CONFIG_TQM8540 1 /* TQM8540 board specific */
-
-#define CONFIG_PCI
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-
-/*
- * sysclk for MPC85xx
- *
- * Two valid values are:
- * 33000000
- * 66000000
- *
- * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
- * is likely the desired value here, so that is now the default.
- * The board, however, can run at 66MHz. In any event, this value
- * must match the settings of some switches. Details can be found
- * in the README.mpc85xxads.
- */
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ 33333333
-#endif
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-
-#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
-
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00000000 /* memtest region */
-#define CFG_MEMTEST_END 0x10000000
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-
-#if defined(CONFIG_SPD_EEPROM)
- /*
- * Determine DDR configuration from I2C interface.
- */
- #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
-
-#else
- /*
- * Manually set up DDR parameters
- */
- #define CFG_SDRAM_SIZE 512 /* DDR is 256MB */
- #define CFG_DDR_CS0_BNDS 0x0000001f /* 0-256MB */
- #define CFG_DDR_CS0_CONFIG 0x80000102
- #define CFG_DDR_TIMING_1 0x47445331
- #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
- #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
- #define CFG_DDR_MODE 0x40020062 /* DLL,normal,seq,4/2.5 */
- #define CFG_DDR_INTERVAL 0x05160100 /* autocharge,no open page */
-#endif
-
-/*
- * Flash on the Local Bus
- */
-#define CFG_LBC_FLASH_BASE 0xfe000000 /* Localbus SDRAM */
-#define CFG_LBC_FLASH_SIZE 32 /* LBC SDRAM is 32MB */
-
-#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH 32M */
-#define CFG_BR0_PRELIM 0xfe001801 /* port size 32bit */
-
-#define CFG_OR0_PRELIM 0xfe000040 /* 32MB Flash */
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 256 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
-#else
-#undef CFG_RAMBOOT
-#endif
-
-#define CFG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
-
-#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */
-#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
-#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/
-
-/*
- * LSDMR masks
- */
-#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
-#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
-#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
-#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16))
-#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
-#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
-#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
-#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
-#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
-#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27))
-#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
-#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29))
-#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
-
-#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
-
-#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_BSMA1516 \
- | CFG_LBC_LSDMR_RFCR5 \
- | CFG_LBC_LSDMR_PRETOACT3 \
- | CFG_LBC_LSDMR_ACTTORW3 \
- | CFG_LBC_LSDMR_BL8 \
- | CFG_LBC_LSDMR_WRC2 \
- | CFG_LBC_LSDMR_CL3 \
- | CFG_LBC_LSDMR_RFEN \
- )
-
-/*
- * SDRAM Controller configuration sequence.
- */
-#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_PCHALL)
-#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_MRW)
-#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_NORMAL)
-
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
-
-/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */
-
-/* I2C RTC */
-#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */
-#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-
-/* I2C EEPROM */
-/*
- * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work also).
- */
-#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
-#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */
-
-/* I2C SYSMON (LM75) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP 70
-#define CFG_DTT_LOW_TEMP -30
-#define CFG_DTT_HYSTERESIS 3
-
-/* RapidIO MMU */
-#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
-#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
-#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
-
-#if defined(CONFIG_PCI)
-
-#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-
-#endif /* CONFIG_PCI */
-
-
-#if defined(CONFIG_TSEC_ENET)
-
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MPC85XX_TSEC1 1
-#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
-#define CONFIG_MPC85XX_TSEC2 1
-#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 2
-#define TSEC2_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-
-#define CONFIG_MPC85XX_FEC 1
-#define CONFIG_MPC85XX_FEC_NAME "FEC"
-#define FEC_PHY_ADDR 3
-#define FEC_PHYIDX 0
-
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-
-/* Options are TSEC[0-1], FEC */
-#define CONFIG_ETHPRIME "TSEC1"
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#ifndef CFG_RAMBOOT
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x20000)
- #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
- #define CFG_ENV_SIZE 0x2000
- #define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET-CFG_ENV_SECT_SIZE)
- #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
- #define CFG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-#if defined(CFG_RAMBOOT)
-# define CONFIG_CMD_PRIV (CONFIG_CMD_DFL & ~(CFG_CMD_ENV | CFG_CMD_LOADS))
-#else
-# define CONFIG_CMD_PRIV (CONFIG_CMD_DFL | \
- CFG_CMD_DHCP | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP )
-#endif
-
-#if defined(CONFIG_PCI)
-# define ADD_PCI_CMD (CFG_CMD_PCI)
-#else
-# define ADD_PCI_CMD 0
-#endif
-
-#define CONFIG_COMMANDS (CONFIG_CMD_PRIV | \
- ADD_PCI_CMD | \
- CFG_CMD_I2C | \
- CFG_CMD_DATE | \
- CFG_CMD_EEPROM | \
- CFG_CMD_DTT | \
- CFG_CMD_MII | \
- CFG_CMD_PING )
-#include <cmd_confdefs.h>
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
-
-#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consdev=ttyS0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $bootargs " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask" \
- ":$hostname:$netdev:off panic=1\0" \
- "addcons=setenv bootargs $bootargs " \
- "console=$consdev,$baudrate\0" \
- "flash_nfs=run nfsargs addip addcons;" \
- "bootm $kernel_addr\0" \
- "flash_self=run ramargs addip addcons;" \
- "bootm $kernel_addr $ramdisk_addr\0" \
- "net_nfs=tftp $loadaddr $bootfile;" \
- "run nfsargs addip addcons;bootm\0" \
- "rootpath=/opt/eldk/ppc_85xx\0" \
- "bootfile=/tftpboot/tqm8540/uImage\0" \
- "kernel_addr=FE000000\0" \
- "ramdisk_addr=FE100000\0" \
- "load=tftp 100000 /tftpboot/tqm8540/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * Copyright 2005 DENX Software Engineering
- * Wolfgang Denk <wd@denx.de>
- * Copyright 2004 Freescale Semiconductor.
- * (C) Copyright 2002,2003 Motorola,Inc.
- * Xianghua Xiao <X.Xiao@motorola.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * TQM8560 board configuration file
- *
- * Make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_CPM2 1 /* has CPM2 */
-#define CONFIG_MPC8560 1 /* MPC8560 specific */
-#define CONFIG_TQM8560 1 /* TQM8560 board specific */
-
-/*
- * BIG FAT WARNING: Right now PCI seems to have a problem on the
- * TQM8560 on the Starter Kit. So, if the board doen't come up
- * please disable the PCI support for now. sr@denx.de, 15-09-2005
- */
-#define CONFIG_PCI
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-
-/*
- * sysclk for MPC85xx
- *
- * Two valid values are:
- * 33000000
- * 66000000
- *
- * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
- * is likely the desired value here, so that is now the default.
- * The board, however, can run at 66MHz. In any event, this value
- * must match the settings of some switches. Details can be found
- * in the README.mpc85xxads.
- */
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ 33333333
-#endif
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-
-#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
-
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00000000 /* memtest region */
-#define CFG_MEMTEST_END 0x10000000
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-
-#if defined(CONFIG_SPD_EEPROM)
- /*
- * Determine DDR configuration from I2C interface.
- */
- #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
-
-#else
- /*
- * Manually set up DDR parameters
- */
- #define CFG_SDRAM_SIZE 512 /* DDR is 256MB */
- #define CFG_DDR_CS0_BNDS 0x0000001f /* 0-256MB */
- #define CFG_DDR_CS0_CONFIG 0x80000102
- #define CFG_DDR_TIMING_1 0x47445331
- #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
- #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
- #define CFG_DDR_MODE 0x40020062 /* DLL,normal,seq,4/2.5 */
- #define CFG_DDR_INTERVAL 0x05160100 /* autocharge,no open page */
-#endif
-
-/*
- * Flash on the Local Bus
- */
-#define CFG_LBC_FLASH_BASE 0xfe000000 /* Localbus SDRAM */
-#define CFG_LBC_FLASH_SIZE 32 /* LBC SDRAM is 32MB */
-
-#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH 32M */
-#define CFG_BR0_PRELIM 0xfe001801 /* port size 32bit */
-
-#define CFG_OR0_PRELIM 0xfe000040 /* 32MB Flash */
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 256 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
-#else
-#undef CFG_RAMBOOT
-#endif
-
-#define CFG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
-
-#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */
-#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
-#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/
-
-/*
- * LSDMR masks
- */
-#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
-#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
-#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
-#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16))
-#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
-#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
-#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
-#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
-#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
-#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27))
-#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
-#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29))
-#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
-
-#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
-
-#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_BSMA1516 \
- | CFG_LBC_LSDMR_RFCR5 \
- | CFG_LBC_LSDMR_PRETOACT3 \
- | CFG_LBC_LSDMR_ACTTORW3 \
- | CFG_LBC_LSDMR_BL8 \
- | CFG_LBC_LSDMR_WRC2 \
- | CFG_LBC_LSDMR_CL3 \
- | CFG_LBC_LSDMR_RFEN \
- )
-
-/*
- * SDRAM Controller configuration sequence.
- */
-#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_PCHALL)
-#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_MRW)
-#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_NORMAL)
-
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
-
-/* Serial Port */
-#define CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */
-
-/* I2C RTC */
-#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */
-#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-
-/* I2C EEPROM */
-/*
- * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work also).
- */
-#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
-#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */
-
-/* I2C SYSMON (LM75) */
-#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP 70
-#define CFG_DTT_LOW_TEMP -30
-#define CFG_DTT_HYSTERESIS 3
-
-/* RapidIO MMU */
-#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
-#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
-#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
-
-#if defined(CONFIG_PCI)
-
-#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
-#define CONFIG_EEPRO100
-#undef CONFIG_TULIP
-
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-
-#endif /* CONFIG_PCI */
-
-
-#if defined(CONFIG_TSEC_ENET)
-
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MPC85XX_TSEC1 1
-#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
-#define CONFIG_MPC85XX_TSEC2 1
-#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 2
-#define TSEC2_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-
-#define CONFIG_MPC85XX_FEC 1
-#define CONFIG_MPC85XX_FEC_NAME "FEC"
-#define FEC_PHY_ADDR 3
-#define FEC_PHYIDX 0
-
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-
-/* Options are TSEC[0-1], FEC */
-#define CONFIG_ETHPRIME "TSEC0"
-
-#endif /* CONFIG_TSEC_ENET */
-
-#define CONFIG_ETHER_ON_FCC
-#define CONFIG_ETHER_ON_FCC3
-#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
-#define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14)
-#define CFG_CPMFCR_RAMTYPE 0
-#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-/*
- * Environment
- */
-#ifndef CFG_RAMBOOT
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x20000)
- #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
- #define CFG_ENV_SIZE 0x2000
- #define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET-CFG_ENV_SECT_SIZE)
- #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
- #define CFG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-#if defined(CFG_RAMBOOT)
-# define CONFIG_CMD_PRIV (CONFIG_CMD_DFL & ~(CFG_CMD_ENV | CFG_CMD_LOADS))
-#else
-# define CONFIG_CMD_PRIV (CONFIG_CMD_DFL | \
- CFG_CMD_DHCP | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP )
-#endif
-
-#if defined(CONFIG_PCI)
-# define ADD_PCI_CMD (CFG_CMD_PCI)
-#else
-# define ADD_PCI_CMD 0
-#endif
-
-#define CONFIG_COMMANDS (CONFIG_CMD_PRIV | \
- ADD_PCI_CMD | \
- CFG_CMD_I2C | \
- CFG_CMD_DATE | \
- CFG_CMD_EEPROM | \
- CFG_CMD_DTT | \
- CFG_CMD_MII | \
- CFG_CMD_PING )
-#include <cmd_confdefs.h>
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
-
-#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consdev=ttyS0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $bootargs " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask" \
- ":$hostname:$netdev:off panic=1\0" \
- "addcons=setenv bootargs $bootargs " \
- "console=$consdev,$baudrate\0" \
- "flash_nfs=run nfsargs addip addcons;" \
- "bootm $kernel_addr\0" \
- "flash_self=run ramargs addip addcons;" \
- "bootm $kernel_addr $ramdisk_addr\0" \
- "net_nfs=tftp $loadaddr $bootfile;" \
- "run nfsargs addip addcons;bootm\0" \
- "rootpath=/opt/eldk/ppc_85xx\0" \
- "bootfile=/tftpboot/tqm8560/uImage\0" \
- "kernel_addr=FE000000\0" \
- "ramdisk_addr=FE100000\0" \
- "load=tftp 100000 /tftpboot/tqm8560/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2005
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * Wolfgang Denk <wd@denx.de>
+ * Copyright 2004 Freescale Semiconductor.
+ * (C) Copyright 2002,2003 Motorola,Inc.
+ * Xianghua Xiao <X.Xiao@motorola.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * TQM85xx (8560/40/55/41) board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */
+
+#define CONFIG_PCI
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+
+#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+
+/*
+ * Only MPC8540 doesn't have CPM module
+ */
+#ifndef CONFIG_MPC8540
+#define CONFIG_CPM2 1 /* has CPM2 */
+#endif
+
+/*
+ * sysclk for MPC85xx
+ *
+ * Two valid values are:
+ * 33000000
+ * 66000000
+ *
+ * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
+ * is likely the desired value here, so that is now the default.
+ * The board, however, can run at 66MHz. In any event, this value
+ * must match the settings of some switches. Details can be found
+ * in the README.mpc85xxads.
+ */
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ 33333333
+#endif
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
+
+#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00000000
+#define CFG_MEMTEST_END 0x10000000
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_ADD_RAM_INFO 1 /* print additional info*/
+
+#if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560)
+/* TQM8540 & 8560 need DLL-override */
+#define CONFIG_DDR_DLL /* DLL fix needed */
+#define CONFIG_DDR_DEFAULT_CL 25 /* CAS latency 2,5 */
+#endif /* defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) */
+
+#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555)
+#define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */
+#endif /* defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) */
+
+/*
+ * Flash on the Local Bus
+ */
+#define CFG_FLASH0 0xFC000000
+#define CFG_FLASH1 0xF8000000
+#define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 }
+
+#define CFG_LBC_FLASH_BASE CFG_FLASH1 /* Localbus flash start */
+#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */
+
+#define CFG_BR0_PRELIM 0xfc001801 /* port size 32bit */
+#define CFG_OR0_PRELIM 0xfc000040 /* 64MB Flash */
+#define CFG_BR1_PRELIM 0xf8001801 /* port size 32bit */
+#define CFG_OR1_PRELIM 0xfc000040 /* 64MB Flash */
+
+#define CFG_FLASH_CFI /* flash is CFI compat. */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */
+#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/
+
+#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
+#define CFG_MAX_FLASH_SECT 512 /* sectors per device */
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */
+#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
+#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data*/
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon*/
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/* Serial Port */
+#if defined(CONFIG_TQM8560)
+
+#define CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else */
+#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
+
+#else
+
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+
+#endif /* CONFIG_TQM8560 */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* I2C */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */
+
+/* I2C RTC */
+#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */
+#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
+
+/* I2C EEPROM */
+/*
+ * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work also).
+ */
+#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
+#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */
+
+/* I2C SYSMON (LM75) */
+#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
+#define CFG_DTT_MAX_TEMP 70
+#define CFG_DTT_LOW_TEMP -30
+#define CFG_DTT_HYSTERESIS 3
+
+/* RapidIO MMU */
+#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0xe2000000
+#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+#endif /* CONFIG_PCI */
+
+
+#define CONFIG_NET_MULTI 1
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MPC85XX_TSEC1 1
+#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
+#define CONFIG_MPC85XX_TSEC2 1
+#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
+#define TSEC1_PHY_ADDR 2
+#define TSEC2_PHY_ADDR 1
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define FEC_PHY_ADDR 3
+#define FEC_PHYIDX 0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+
+/* Options are TSEC[0-1], FEC */
+#define CONFIG_ETHPRIME "TSEC0"
+
+#if defined(CONFIG_TQM8540)
+/*
+ * TQM8540 has 3 ethernet ports. 2 TSEC's and one FEC.
+ * The FEC port is connected on the same signals as the FCC3 port
+ * of the TQM8560 to the baseboard (STK85xx Starterkit).
+ *
+ * On the STK85xx Starterkit the X47/X50 jumper has to be set to
+ * a - d (X50.2 - 3) to enable the FEC port.
+ */
+#define CONFIG_MPC85XX_FEC 1
+#define CONFIG_MPC85XX_FEC_NAME "FEC"
+#endif
+
+#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555)
+/*
+ * TQM8541/55 have 4 ethernet ports. 2 TSEC's and 2 FCC's. Only one FCC port
+ * can be used at once, since only one FCC port is available on the STK85xx
+ * Starterkit.
+ *
+ * To use this port you have to configure U-Boot to use the FCC port 1...2
+ * and set the X47/X50 jumper to:
+ * FCC1: a - b (X47.2 - X50.2)
+ * FCC2: a - c (X50.2 - 1)
+ */
+#define CONFIG_ETHER_ON_FCC
+#define CONFIG_ETHER_INDEX 1 /* FCC channel for ethernet */
+#endif
+
+#if defined(CONFIG_TQM8560)
+/*
+ * TQM8560 has 5 ethernet ports. 2 TSEC's and 3 FCC's. Only one FCC port
+ * can be used at once, since only one FCC port is available on the STK85xx
+ * Starterkit.
+ *
+ * To use this port you have to configure U-Boot to use the FCC port 1...3
+ * and set the X47/X50 jumper to:
+ * FCC1: a - b (X47.2 - X50.2)
+ * FCC2: a - c (X50.2 - 1)
+ * FCC3: a - d (X50.2 - 3)
+ */
+#define CONFIG_ETHER_ON_FCC
+#define CONFIG_ETHER_INDEX 3 /* FCC channel for ethernet */
+#endif
+
+#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1)
+#define CONFIG_ETHER_ON_FCC1
+#define CFG_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
+#define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12)
+#define CFG_CPMFCR_RAMTYPE 0
+#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
+#endif
+
+#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
+#define CONFIG_ETHER_ON_FCC2
+#define CFG_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+#define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK16 | CMXFCR_TF2CS_CLK13)
+#define CFG_CPMFCR_RAMTYPE 0
+#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
+#endif
+
+#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3)
+#define CONFIG_ETHER_ON_FCC3
+#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
+#define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14)
+#define CFG_CPMFCR_RAMTYPE 0
+#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
+#endif
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x20000)
+#define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+#define CFG_ENV_SIZE 0x2000
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_TIMESTAMP /* Print image info with ts */
+
+#if defined(CONFIG_PCI)
+# define ADD_PCI_CMD (CFG_CMD_PCI)
+#else
+# define ADD_PCI_CMD 0
+#endif
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_NFS | \
+ CFG_CMD_SNTP | \
+ ADD_PCI_CMD | \
+ CFG_CMD_I2C | \
+ CFG_CMD_DATE | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DTT | \
+ CFG_CMD_MII | \
+ CFG_CMD_PING )
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buf Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+
+#define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/
+
+#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CFG_BOOTFILE \
+ "netdev=eth0\0" \
+ "consdev=ttyS0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs $bootargs " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask" \
+ ":$hostname:$netdev:off panic=1\0" \
+ "addcons=setenv bootargs $bootargs " \
+ "console=$consdev,$baudrate\0" \
+ "flash_nfs=run nfsargs addip addcons;" \
+ "bootm $kernel_addr\0" \
+ "flash_self=run ramargs addip addcons;" \
+ "bootm $kernel_addr $ramdisk_addr\0" \
+ "net_nfs=tftp $loadaddr $bootfile;" \
+ "run nfsargs addip addcons;bootm\0" \
+ "rootpath=/opt/eldk/ppc_85xx\0" \
+ "kernel_addr=FE000000\0" \
+ "ramdisk_addr=FE100000\0" \
+ "load=tftp 100000 /tftpboot/$hostname/u-boot.bin\0" \
+ "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
+ "cp.b 100000 fffc0000 40000;" \
+ "setenv filesize;saveenv\0" \
+ "upd=run load;run update\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+#endif /* __CONFIG_H */
/***********************************************************************/
+#ifdef CONFIG_ADD_RAM_INFO
+void board_add_ram_info(int);
+#endif
+
static int init_func_ram (void)
{
#ifdef CONFIG_BOARD_TYPES
puts ("DRAM: ");
if ((gd->ram_size = initdram (board_type)) > 0) {
- print_size (gd->ram_size, "\n");
+ print_size (gd->ram_size, "");
+#ifdef CONFIG_ADD_RAM_INFO
+ board_add_ram_info(0);
+#endif
+ putc('\n');
return (0);
}
puts (failed);
#ifdef SCC_ENET
scc_initialize(bis);
#endif
-#if defined(FEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
- fec_initialize(bis);
-#endif
#if defined(CONFIG_MPC5xxx_FEC)
mpc5xxx_fec_initialize(bis);
#endif
tsec_initialize(bis, 3, CONFIG_MPC83XX_TSEC4_NAME);
# endif
#endif
+#if defined(FEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+ fec_initialize(bis);
+#endif
#if defined(CONFIG_AU1X00)
au1x00_enet_initialize(bis);
#endif
projects / u-boot.git / commitdiff