@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/sequoia/config.tmp
@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+sequoia_ramboot_config \
+rainier_ramboot_config: unconfig
+ @mkdir -p $(obj)include $(obj)board/amcc/sequoia
+ @echo "#define CONFIG_SYS_RAMBOOT" > $(obj)include/config.h
+ @echo "#define CONFIG_$$(echo $(subst ,,$(@:_config=)) | \
+ tr '[:lower:]' '[:upper:]')" >> $(obj)include/config.h
+ @$(MKCONFIG) -n $@ -a sequoia ppc ppc4xx sequoia amcc
+ @echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/sequoia/config.tmp
+ @echo "LDSCRIPT = board/amcc/sequoia/u-boot-ram.lds" >> \
+ $(obj)board/amcc/sequoia/config.tmp
+
taihu_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc ppc4xx taihu amcc
/* vxWorks needs this as first entry for the Machine Check interrupt */
tlbentry( 0x40000000, SZ_256M, 0, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
+ /*
+ * The RAM-boot version skips the SDRAM TLB (identified by EPN=0). This
+ * entry is already configured for SDRAM via the JTAG debugger and mustn't
+ * be re-initialized by this RAM-booting U-Boot version.
+ */
+#ifndef CONFIG_SYS_RAMBOOT
/* TLB-entry for DDR SDRAM (Up to 2GB) */
#ifdef CONFIG_4xx_DCACHE
tlbentry( CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G)
#else
tlbentry( CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
#endif
+#endif /* CONFIG_SYS_RAMBOOT */
/* TLB-entry for EBC */
tlbentry( CONFIG_SYS_BCSR_BASE, SZ_256M, CONFIG_SYS_BCSR_BASE, 1, AC_R|AC_W|AC_X|SA_G|SA_I )
************************************************************************/
phys_size_t initdram (int board_type)
{
-#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT)) || \
+ defined(CONFIG_NAND_SPL)
ulong speed = get_bus_freq(0);
mtsdram(DDR0_02, 0x00000000);
DECLARE_GLOBAL_DATA_PTR;
+#if !defined(CONFIG_SYS_NO_FLASH)
extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
+#endif
extern void __ft_board_setup(void *blob, bd_t *bd);
ulong flash_get_size(ulong base, int banknum);
int misc_init_r(void)
{
+#if !defined(CONFIG_SYS_NO_FLASH)
uint pbcr;
int size_val = 0;
- u32 reg;
+#endif
#ifdef CONFIG_440EPX
unsigned long usb2d0cr = 0;
unsigned long usb2phy0cr, usb2h0cr = 0;
unsigned long sdr0_pfc1;
char *act = getenv("usbact");
#endif
+ u32 reg;
+#if !defined(CONFIG_SYS_NO_FLASH)
/* Re-do flash sizing to get full correct info */
/* adjust flash start and offset */
CONFIG_ENV_ADDR_REDUND + 2*CONFIG_ENV_SECT_SIZE - 1,
&flash_info[0]);
#endif
+#endif /* CONFIG_SYS_NO_FLASH */
/*
* USB suff...
}
#endif /* CONFIG_POST */
-#if defined(CONFIG_NAND_U_BOOT)
+#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT)
/*
* On NAND-booting sequoia, we need to patch the chips select numbers
* in the dtb (CS0 - NAND, CS3 - NOR)
--- /dev/null
+/*
+ * (C) Copyright 2009
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SECTIONS
+{
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ cpu/ppc4xx/start.o (.text)
+
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x00FF) & 0xFFFFFF00;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+ __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss (NOLOAD) :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ . = ALIGN(4);
+ }
+
+ _end = . ;
+ PROVIDE (end = .);
+}
bl board_init_f
#endif
+#if defined(CONFIG_SYS_RAMBOOT)
+ /*
+ * 4xx RAM-booting U-Boot image is started from offset 0
+ */
+ .text
+ bl _start_440
+#endif
+
/*
* 440 Startup -- on reset only the top 4k of the effective
* address space is mapped in by an entry in the instruction
addis r0,0,0x0000
li r1,0x003f /* 64 TLB entries */
mtctr r1
-rsttlb: tlbwe r0,r1,0x0000 /* Invalidate all entries (V=0)*/
- tlbwe r0,r1,0x0001
- tlbwe r0,r1,0x0002
- subi r1,r1,0x0001
+ li r4,0 /* Start with TLB #0 */
+rsttlb:
+#ifdef CONFIG_SYS_RAMBOOT
+ tlbre r3,r4,0 /* Read contents from TLB word #0 to get EPN */
+ rlwinm. r3,r3,0,0xfffffc00 /* Mask EPN */
+ beq tlbnxt /* Skip EPN=0 TLB, this is the SDRAM TLB */
+#endif
+ tlbwe r0,r4,0 /* Invalidate all entries (V=0)*/
+ tlbwe r0,r4,1
+ tlbwe r0,r4,2
+tlbnxt: addi r4,r4,1 /* Next TLB */
bdnz rsttlb
/*----------------------------------------------------------------*/
li r4,0 /* TLB # */
addi r5,r5,-4
-1: lwzu r0,4(r5)
+1:
+#ifdef CONFIG_SYS_RAMBOOT
+ tlbre r3,r4,0 /* Read contents from TLB word #0 */
+ rlwinm. r3,r3,0,0x00000200 /* Mask V (valid) bit */
+ bne tlbnx2 /* Skip V=1 TLB, this is the SDRAM TLB */
+#endif
+ lwzu r0,4(r5)
cmpwi r0,0
beq 2f /* 0 marks end */
lwzu r1,4(r5)
tlbwe r0,r4,0 /* TLB Word 0 */
tlbwe r1,r4,1 /* TLB Word 1 */
tlbwe r2,r4,2 /* TLB Word 2 */
- addi r4,r4,1 /* Next TLB */
+tlbnx2: addi r4,r4,1 /* Next TLB */
bdnz 1b
/*----------------------------------------------------------------*/
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
+#if defined(CONFIG_SYS_RAMBOOT)
+/*
+ * Disable NOR FLASH commands on RAM-booting version. One main reason for this
+ * RAM-booting version is boards with NAND and without NOR. This image can
+ * be used for initial NAND programming.
+ */
+#define CONFIG_SYS_NO_FLASH
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_IMLS
+#endif
+
/*
* Miscellaneous configurable options
*/
/*
* Environment
*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environ vars */
+#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+#define CONFIG_ENV_IS_IN_NAND /* use NAND for environ vars */
+#define CONFIG_ENV_IS_EMBEDDED /* use embedded environment */
+#elif defined(CONFIG_SYS_RAMBOOT)
+#define CONFIG_ENV_IS_NOWHERE /* Store env in memory only */
+#define CONFIG_ENV_SIZE (8 << 10)
+/*
+ * In RAM-booting version, we have no environment storage. So we need to
+ * provide at least preliminary MAC addresses for the 4xx EMAC driver to
+ * register the interfaces. Those two addresses are generated via the
+ * tools/gen_eth_addr tool and should only be used in a closed laboratory
+ * environment.
+ */
+#define CONFIG_ETHADDR 4a:56:49:22:3e:43
+#define CONFIG_ETH1ADDR 02:93:53:d5:06:98
#else
-#define CONFIG_ENV_IS_IN_NAND 1 /* use NAND for environ vars */
-#define CONFIG_ENV_IS_EMBEDDED 1 /* use embedded environment */
+#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environ vars */
#endif
+#if defined(CONFIG_CMD_FLASH)
/*
* FLASH related
*/
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
+#endif /* CONFIG_CMD_FLASH */
/*
* IPL (Initial Program Loader, integrated inside CPU)
* DDR SDRAM
*/
#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) && \
+ !defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
#endif
#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
* overwrite part of the U-Boot image which is already loaded from NAND
* to SDRAM.
*/
-#if defined(CONFIG_NAND_U_BOOT)
+#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_SYS_POST_MEMORY_ON 0
#else
#define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORY
/*
* On Sequoia CS0 and CS3 are switched when configuring for NAND booting
*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) && \
+ !defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
#define CONFIG_SYS_EBC_PB0AP 0x03017200
projects / u-boot.git / commitdiff