Remove rev 1 fixes.
Always set PICGCR_MODE.
Enable machine check and provide board config option
to set and handle SoC error interrupts.
Include MSSSR0 in error message.
Isolate a RAMBOOT bit of code with #ifdef CFG_RAMBOOT.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
/* enable the timebase bit in HID0 */
set_hid0(get_hid0() | 0x4000000);
- /* enable SYNCBE | ABE bits in HID1 */
- set_hid1(get_hid1() | 0x00000C00);
+ /* enable EMCP, SYNCBE | ABE bits in HID1 */
+ set_hid1(get_hid1() | 0x80000C00);
}
/*
* (C) Copyright 2003 Motorola Inc. (MPC85xx port)
* Xianghua Xiao (X.Xiao@motorola.com)
*
- * (C) Copyright 2004 Freescale Semiconductor. (MPC86xx Port)
+ * (C) Copyright 2004, 2007 Freescale Semiconductor. (MPC86xx Port)
* Jeff Brown
* Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
*
{
int ret;
- /*
- * The IRQ0 on Rev 2 is pulled high (low in Rev 1.x) to
- * implement PEX10 errata. As INT is active high, it
- * will cause core to take 0x500 interrupt.
- *
- * Due to the PIC's default pass through mode, as soon
- * as interrupts are enabled (MSR[EE] = 1), an interrupt
- * will be taken and u-boot will hang. This is due to a
- * hardware change (per an errata fix) on new revisions
- * of the board with Rev 2.x parts.
- *
- * Setting the PIC to mixed mode prevents the hang.
- */
- if ((get_svr() & 0xf0) == 0x20) {
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
- immr->im_pic.gcr = MPC86xx_PICGCR_RST;
- while (immr->im_pic.gcr & MPC86xx_PICGCR_RST);
- immr->im_pic.gcr = MPC86xx_PICGCR_MODE;
- }
+ volatile immap_t *immr = (immap_t *)CFG_IMMR;
+ immr->im_pic.gcr = MPC86xx_PICGCR_RST;
+ while (immr->im_pic.gcr & MPC86xx_PICGCR_RST);
+ immr->im_pic.gcr = MPC86xx_PICGCR_MODE;
/* call cpu specific function from $(CPU)/interrupts.c */
ret = interrupt_init_cpu(&decrementer_count);
get_msr(),
get_dec());
+#ifdef CONFIG_INTERRUPTS
+ volatile ccsr_pic_t *pic = &immr->im_pic;
+
+ pic->iivpr1 = 0x810001; /* 50220 enable mcm interrupts */
+ debug("iivpr1@%x = %x\n", &pic->iivpr1, pic->iivpr1);
+
+ pic->iivpr2 = 0x810002; /* 50240 enable ddr interrupts */
+ debug("iivpr2@%x = %x\n", &pic->iivpr2, pic->iivpr2);
+
+ pic->iivpr3 = 0x810003; /* 50260 enable lbc interrupts */
+ debug("iivpr3@%x = %x\n", &pic->iivpr3, pic->iivpr3);
+
+#if defined(CONFIG_PCI1) || defined(CONFIG_PCIE1)
+ pic->iivpr8 = 0x810008; /* enable pcie1 interrupts */
+ debug("iivpr8@%x = %x\n", &pic->iivpr8, pic->iivpr8);
+#endif
+#if defined(CONFIG_PCI2) || defined(CONFIG_PCIE2)
+ pic->iivpr9 = 0x810009; /* enable pcie2 interrupts */
+ debug("iivpr9@%x = %x\n", &pic->iivpr9, pic->iivpr9);
+#endif
+
+ pic->ctpr = 0; /* 40080 clear current task priority register */
+#endif
+
return 0;
}
timestamp++;
- ppcDcbf((unsigned long)×tamp);
-
/* Restore Decrementer Count */
set_dec(decrementer_count);
/*
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2004, 2007 Freescale Semiconductor.
* Srikanth Srinivasan <srikanth.srinivaan@freescale.com>
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_IDENT_STRING ""
#endif
-/* We don't want the MMU yet.
-*/
-#undef MSR_KERNEL
-/* Machine Check and Recoverable Interr. */
-#define MSR_KERNEL ( MSR_ME | MSR_RI )
+/*
+ * Need MSR_DR | MSR_IR enabled to access I/O (printf) in exceptions
+ */
/*
* Set up GOT: Global Offset Table
bl secondary_cpu_setup
#endif
+1:
+#ifdef CFG_RAMBOOT
/* disable everything */
-1: li r0, 0
+ li r0, 0
mtspr HID0, r0
sync
mtmsr 0
+#endif
+
bl invalidate_bats
sync
#ifdef CFG_L2
/* init the L2 cache */
- addis r3, r0, L2_INIT@h
+ lis r3, L2_INIT@h
ori r3, r3, L2_INIT@l
mtspr l2cr, r3
/* invalidate the L2 cache */
bl setup_ccsrbar
#endif
-
- /* -- MPC8641 Rev 1.0 MCM Errata fixups -- */
-
- /* skip fixups if not Rev 1.0 */
- mfspr r4, SVR
- rlwinm r4,r4,0,24,31
- cmpwi r4,0x10
- bne 1f
-
- lis r3,MCM_ABCR@ha
- lwz r4,MCM_ABCR@l(r3) /* ABCR -> r4 */
-
- /* set ABCR[A_STRM_CNT] = 0 */
- rlwinm r4,r4,0,0,29
-
- /* set ABCR[ARB_POLICY] to 0x1 (round-robin) */
- addi r0,r0,1
- rlwimi r4,r0,12,18,19
-
- stw r4,MCM_ABCR@l(r3) /* r4 -> ABCR */
- sync
-
- /* Set DBCR[ERD_DIS] */
- lis r3,MCM_DBCR@ha
- lwz r4,MCM_DBCR@l(r3)
- oris r4, r4, 0x4000
- stw r4,MCM_DBCR@l(r3)
- sync
-1:
/* setup the law entries */
bl law_entry
sync
-
-
-#if (EMULATOR_RUN == 1)
- /* On the emulator we want to adjust these ASAP */
- /* otherwise things are sloooow */
- /* Setup OR0 (LALE FIX)*/
- lis r3, CFG_CCSRBAR@h
- ori r3, r3, 0x5004
- li r4, 0x0FF3
- stw r4, 0(r3)
- sync
-
- /* Setup LCRR */
- lis r3, CFG_CCSRBAR@h
- ori r3, r3, 0x50D4
- lis r4, 0x8000
- ori r4, r4, 0x0002
- stw r4, 0(r3)
- sync
-#endif
-#if 1
- /* make sure timer enabled in guts register too */
- lis r3, CFG_CCSRBAR@h
- oris r3,r3, 0xE
- ori r3,r3,0x0070
- lwz r4, 0(r3)
- lis r5,0xFFFC
- ori r5,r5,0x5FFF
- and r4,r4,r5
- stw r4,0(r3)
-#endif
/*
* Cache must be enabled here for stack-in-cache trick.
* This means we need to enable the BATS.
#ifdef RUN_DIAG
- /* Sri: Code to run the diagnostic automatically */
-
/* Load PX_AUX register address in r4 */
lis r4, 0xf810
ori r4, r4, 0x6
.globl invalidate_bats
invalidate_bats:
+ li r0, 0
/* invalidate BATs */
mtspr IBAT0U, r0
mtspr IBAT1U, r0
mfmsr r7
li r8,MSR_IP
andc r7,r7,r8
+ ori r7,r7,MSR_ME /* Enable Machine Check */
mtmsr r7
mtlr r4 /* restore link register */
sync
isync
- /*SYNCBE|ABE in HID1*/
+ /* MCP|SYNCBE|ABE in HID1 */
mfspr r4, HID1
+ oris r4, r4, 0x8000
ori r4, r4, 0x0C00
mtspr HID1, r4
sync
printf("Machine check in kernel mode.\n");
printf("Caused by (from msr): ");
printf("regs %p ", regs);
- switch (regs->msr & 0x000F0000) {
- case (0x80000000 >> 12):
+ switch ( regs->msr & 0x001F0000) {
+ case (0x80000000>>11):
+ printf("MSS error. MSSSR0: %08x\n", mfspr(SPRN_MSSSR0));
+ break;
+ case (0x80000000>>12):
printf("Machine check signal - probably due to mm fault\n"
"with mmu off\n");
break;
if (debugger_exception_handler && (*debugger_exception_handler) (regs))
return;
#endif
+ printf("UnknownException regs@%x\n", regs);
printf("Bad trap at PC: %lx, SR: %lx, vector=%lx\n",
regs->nip, regs->msr, regs->trap);
_exception(0, regs);
uint porpllsr; /* 0xe0000 - POR PLL ratio status register */
uint porbmsr; /* 0xe0004 - POR boot mode status register */
#define MPC86xx_PORBMSR_HA 0x00060000
+#define MPC85xx_PORBMSR_HA 0x00070000
uint porimpscr; /* 0xe0008 - POR I/O impedance status and control register */
uint pordevsr; /* 0xe000c - POR I/O device status regsiter */
-#define MPC86xx_PORDEVSR_IO_SEL 0x000F0000
+#define MPC86xx_PORDEVSR_IO_SEL 0x000F0000
+#define MPC85xx_PORDEVSR_IO_SEL 0x00380000 /* 85xx platform type */
+#define MPC86xx_PORDEVSR_CORE1TE 0x00000080 /* ASMP (Core1 addr trans) */
uint pordbgmsr; /* 0xe0010 - POR debug mode status register */
char res1[12];
uint gpporcr; /* 0xe0020 - General-purpose POR configuration register */
uint pmuxcr; /* 0xe0060 - Alternate function signal multiplex control */
char res6[12];
uint devdisr; /* 0xe0070 - Device disable control */
-#define MPC86xx_DEVDISR_PCIEX1 0x80000000
-#define MPC86xx_DEVDISR_PCIEX2 0x40000000
+#define MPC86xx_DEVDISR_PCIEX1 0x80000000
+#define MPC86xx_DEVDISR_PCIEX2 0x40000000
+#define MPC86xx_DEVDISR_PCI1 0x80000000
+#define MPC86xx_DEVDISR_PCIE1 0x40000000
+#define MPC86xx_DEVDISR_PCIE2 0x20000000
char res7[12];
uint powmgtcsr; /* 0xe0080 - Power management status and control register */
char res8[12];
char res9[12];
uint pvr; /* 0xe00a0 - Processor version register */
uint svr; /* 0xe00a4 - System version register */
- char res10[3416];
+ char res10a[1880];
+ uint clkdvdr; /* 0xe0800 - Clock Divide register */
+ char res10b[1532];
uint clkocr; /* 0xe0e00 - Clock out select register */
char res11[12];
uint ddrdllcr; /* 0xe0e10 - DDR DLL control register */
#define ESR_ST 0x00800000 /* Store Operation */
#if defined(CONFIG_MPC86xx)
-#define SPRN_MSSCRO 0x3f6
+#define SPRN_MSSCR0 0x3f6
+#define SPRN_MSSSR0 0x3f7
#endif
projects / u-boot.git / commitdiff