select ARCH_MPC8308
select SYS_FSL_ERRATUM_ESDHC111
-config TARGET_STRIDER
- bool "Support strider"
- select ARCH_MPC8308
- select SYS_FSL_ERRATUM_ESDHC111
- imply CMD_PCA953X
-
config TARGET_GAZERBEAM
bool "Support gazerbeam"
select ARCH_MPC8308
obj-$(CONFIG_CMD_IOLOOP) += cmd_ioloop.o
obj-$(CONFIG_CONTROLCENTERD) += dp501.o
obj-$(CONFIG_TARGET_HRCON) += osd.o mclink.o dp501.o phy.o ioep-fpga.o fanctrl.o
-obj-$(CONFIG_TARGET_STRIDER) += mclink.o dp501.o phy.o ioep-fpga.o adv7611.o ch7301.o
-obj-$(CONFIG_TARGET_STRIDER) += fanctrl.o
-obj-$(CONFIG_STRIDER_CON) += osd.o
-obj-$(CONFIG_STRIDER_CON_DP) += osd.o
obj-$(CONFIG_TARGET_GAZERBEAM) += osd.o ihs_mdio.o ioep-fpga.o
ifdef CONFIG_OSD
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2014
- * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
- */
-
-#ifdef CONFIG_GDSYS_LEGACY_DRIVERS
-
-#include <common.h>
-#include <i2c.h>
-
-#define ADV7611_I2C_ADDR 0x4c
-#define ADV7611_RDINFO 0x2051
-
-/*
- * ADV7611 I2C Addresses in u-boot notation
- */
-enum {
- CP_I2C_ADDR = 0x22,
- DPLL_I2C_ADDR = 0x26,
- KSV_I2C_ADDR = 0x32,
- HDMI_I2C_ADDR = 0x34,
- EDID_I2C_ADDR = 0x36,
- INFOFRAME_I2C_ADDR = 0x3e,
- CEC_I2C_ADDR = 0x40,
- IO_I2C_ADDR = ADV7611_I2C_ADDR,
-};
-
-/*
- * Global Control Registers
- */
-enum {
- IO_RD_INFO_MSB = 0xea,
- IO_RD_INFO_LSB = 0xeb,
- IO_CEC_ADDR = 0xf4,
- IO_INFOFRAME_ADDR = 0xf5,
- IO_DPLL_ADDR = 0xf8,
- IO_KSV_ADDR = 0xf9,
- IO_EDID_ADDR = 0xfa,
- IO_HDMI_ADDR = 0xfb,
- IO_CP_ADDR = 0xfd,
-};
-
-int adv7611_i2c[] = CONFIG_SYS_ADV7611_I2C;
-
-int adv7611_probe(unsigned int screen)
-{
- int old_bus = i2c_get_bus_num();
- unsigned int rd_info;
- int res = 0;
-
- i2c_set_bus_num(adv7611_i2c[screen]);
-
- rd_info = (i2c_reg_read(IO_I2C_ADDR, IO_RD_INFO_MSB) << 8)
- | i2c_reg_read(IO_I2C_ADDR, IO_RD_INFO_LSB);
-
- if (rd_info != ADV7611_RDINFO) {
- res = -1;
- goto out;
- }
-
- /*
- * set I2C addresses to default values
- */
- i2c_reg_write(IO_I2C_ADDR, IO_CEC_ADDR, CEC_I2C_ADDR << 1);
- i2c_reg_write(IO_I2C_ADDR, IO_INFOFRAME_ADDR, INFOFRAME_I2C_ADDR << 1);
- i2c_reg_write(IO_I2C_ADDR, IO_DPLL_ADDR, DPLL_I2C_ADDR << 1);
- i2c_reg_write(IO_I2C_ADDR, IO_KSV_ADDR, KSV_I2C_ADDR << 1);
- i2c_reg_write(IO_I2C_ADDR, IO_EDID_ADDR, EDID_I2C_ADDR << 1);
- i2c_reg_write(IO_I2C_ADDR, IO_HDMI_ADDR, HDMI_I2C_ADDR << 1);
- i2c_reg_write(IO_I2C_ADDR, IO_CP_ADDR, CP_I2C_ADDR << 1);
-
- /*
- * do magic initialization sequence from
- * "ADV7611 Register Settings Recommendations Revision 1.5"
- * with most registers undocumented
- */
- i2c_reg_write(CP_I2C_ADDR, 0x6c, 0x00);
- i2c_reg_write(HDMI_I2C_ADDR, 0x9b, 0x03);
- i2c_reg_write(HDMI_I2C_ADDR, 0x6f, 0x08);
- i2c_reg_write(HDMI_I2C_ADDR, 0x85, 0x1f);
- i2c_reg_write(HDMI_I2C_ADDR, 0x87, 0x70);
- i2c_reg_write(HDMI_I2C_ADDR, 0x57, 0xda);
- i2c_reg_write(HDMI_I2C_ADDR, 0x58, 0x01);
- i2c_reg_write(HDMI_I2C_ADDR, 0x03, 0x98);
- i2c_reg_write(HDMI_I2C_ADDR, 0x4c, 0x44);
-
- /*
- * IO_REG_02, default 0xf0
- *
- * INP_COLOR_SPACE (IO, Address 0x02[7:4])
- * default: 0b1111 auto
- * set to : 0b0001 force RGB (range 0 to 255) input
- *
- * RGB_OUT (IO, Address 0x02[1])
- * default: 0 YPbPr color space output
- * set to : 1 RGB color space output
- */
- i2c_reg_write(IO_I2C_ADDR, 0x02, 0x12);
-
- /*
- * IO_REG_03, default 0x00
- *
- * OP_FORMAT_SEL (IO, Address 0x03[7:0])
- * default: 0x00 8-bit SDR ITU-656 mode
- * set to : 0x40 24-bit 4:4:4 SDR mode
- */
- i2c_reg_write(IO_I2C_ADDR, 0x03, 0x40);
-
- /*
- * IO_REG_05, default 0x2c
- *
- * AVCODE_INSERT_EN (IO, Address 0x05[2])
- * default: 1 insert AV codes into data stream
- * set to : 0 do not insert AV codes into data stream
- */
- i2c_reg_write(IO_I2C_ADDR, 0x05, 0x28);
-
- /*
- * IO_REG_0C, default 0x62
- *
- * POWER_DOWN (IO, Address 0x0C[5])
- * default: 1 chip is powered down
- * set to : 0 chip is operational
- */
- i2c_reg_write(IO_I2C_ADDR, 0x0c, 0x42);
-
- /*
- * IO_REG_15, default 0xbe
- *
- * TRI_SYNCS (IO, Address 0x15[3)
- * TRI_LLC (IO, Address 0x15[2])
- * TRI_PIX (IO, Address 0x15[1])
- * default: 1 video output pins are tristate
- * set to : 0 video output pins are active
- */
- i2c_reg_write(IO_I2C_ADDR, 0x15, 0xb0);
-
- /*
- * HDMI_REGISTER_02H, default 0xff
- *
- * CLOCK_TERMA_DISABLE (HDMI, Address 0x83[0])
- * default: 1 disable termination
- * set to : 0 enable termination
- * Future options are:
- * - use the chips automatic termination control
- * - set this manually on cable detect
- * but at the moment this seems a safe default.
- */
- i2c_reg_write(HDMI_I2C_ADDR, 0x83, 0xfe);
-
- /*
- * HDMI_CP_CNTRL_1, default 0x01
- *
- * HDMI_FRUN_EN (CP, Address 0xBA[0])
- * default: 1 Enable the free run feature in HDMI mode
- * set to : 0 Disable the free run feature in HDMI mode
- */
- i2c_reg_write(CP_I2C_ADDR, 0xba, 0x00);
-
- /*
- * INT1_CONFIGURATION, default 0x20
- *
- * INTRQ_DUR_SEL[1:0] (IO, Address 0x40[7:6])
- * default: 00 Interrupt signal is active for 4 Xtal periods
- * set to : 11 Active until cleared
- *
- * INTRQ_OP_SEL[1:0] (IO, Address 0x40[1:0])
- * default: 00 Open drain
- * set to : 10 Drives high when active
- */
- i2c_reg_write(IO_I2C_ADDR, 0x40, 0xc2);
-
-out:
- i2c_set_bus_num(old_bus);
-
- return res;
-}
-
-#endif /* CONFIG_GDSYS_LEGACY_DRIVERS */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2014
- * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
- */
-
-#ifndef _ADV7611_H_
-#define _ADV7611_H_
-
-int adv7611_probe(unsigned int screen);
-
-#endif
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2014
- * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
- */
-
-/* Chrontel CH7301C DVI Transmitter */
-
-#ifdef CONFIG_GDSYS_LEGACY_DRIVERS
-
-#include <common.h>
-#include <asm/io.h>
-#include <errno.h>
-#include <i2c.h>
-
-#define CH7301_I2C_ADDR 0x75
-
-enum {
- CH7301_CM = 0x1c, /* Clock Mode Register */
- CH7301_IC = 0x1d, /* Input Clock Register */
- CH7301_GPIO = 0x1e, /* GPIO Control Register */
- CH7301_IDF = 0x1f, /* Input Data Format Register */
- CH7301_CD = 0x20, /* Connection Detect Register */
- CH7301_DC = 0x21, /* DAC Control Register */
- CH7301_HPD = 0x23, /* Hot Plug Detection Register */
- CH7301_TCTL = 0x31, /* DVI Control Input Register */
- CH7301_TPCP = 0x33, /* DVI PLL Charge Pump Ctrl Register */
- CH7301_TPD = 0x34, /* DVI PLL Divide Register */
- CH7301_TPVT = 0x35, /* DVI PLL Supply Control Register */
- CH7301_TPF = 0x36, /* DVI PLL Filter Register */
- CH7301_TCT = 0x37, /* DVI Clock Test Register */
- CH7301_TSTP = 0x48, /* Test Pattern Register */
- CH7301_PM = 0x49, /* Power Management register */
- CH7301_VID = 0x4a, /* Version ID Register */
- CH7301_DID = 0x4b, /* Device ID Register */
- CH7301_DSP = 0x56, /* DVI Sync polarity Register */
-};
-
-int ch7301_i2c[] = CONFIG_SYS_CH7301_I2C;
-
-int ch7301_probe(unsigned screen, bool power)
-{
- u8 value;
-
- i2c_set_bus_num(ch7301_i2c[screen]);
- if (i2c_probe(CH7301_I2C_ADDR))
- return -1;
-
- value = i2c_reg_read(CH7301_I2C_ADDR, CH7301_DID);
- if (value != 0x17)
- return -1;
-
- if (power) {
- i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPCP, 0x08);
- i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPD, 0x16);
- i2c_reg_write(CH7301_I2C_ADDR, CH7301_TPF, 0x60);
- i2c_reg_write(CH7301_I2C_ADDR, CH7301_DC, 0x09);
- i2c_reg_write(CH7301_I2C_ADDR, CH7301_PM, 0xc0);
- } else {
- i2c_reg_write(CH7301_I2C_ADDR, CH7301_DC, 0x00);
- i2c_reg_write(CH7301_I2C_ADDR, CH7301_PM, 0x01);
- }
-
- return 0;
-}
-
-#endif /* CONFIG_GDSYS_LEGACY_DRIVERS */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2014
- * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
- */
-
-#ifndef _CH7301_H_
-#define _CH7301_H_
-
-int ch7301_probe(unsigned screen, bool power);
-
-#endif
endif
-if TARGET_STRIDER
-
-config SYS_BOARD
- default "mpc8308"
-
-config SYS_VENDOR
- default "gdsys"
-
-config SYS_CONFIG_NAME
- default "strider"
-
-config GDSYS_LEGACY_OSD_CMDS
- default y
-
-config GDSYS_LEGACY_DRIVERS
- default y
-
-endif
-
if TARGET_GAZERBEAM
config SYS_BOARD
default y
endif
-if TARGET_HRCON || TARGET_STRIDER || TARGET_GAZERBEAM
+if TARGET_HRCON || TARGET_GAZERBEAM
choice
prompt "FPGA flavor selection"
F: include/configs/hrcon.h
F: configs/hrcon_defconfig
F: configs/hrcon_dh_defconfig
-F: include/configs/strider.h
-F: configs/strider_defconfig
-F: configs/strider_cpu_defconfig
-F: configs/strider_cpu_dp_defconfig
-F: configs/strider_con_defconfig
-F: configs/strider_con_dp_defconfig
F: configs/gazerbeam_defconfig
obj-y := mpc8308.o sdram.o
obj-$(CONFIG_TARGET_HRCON) += hrcon.o
-obj-$(CONFIG_TARGET_STRIDER) += strider.o
obj-$(CONFIG_TARGET_GAZERBEAM) += gazerbeam.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2014
- * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
- */
-
-#include <common.h>
-#include <env.h>
-#include <flash.h>
-#include <hwconfig.h>
-#include <i2c.h>
-#include <init.h>
-#include <spi.h>
-#include <linux/bitops.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <pci.h>
-#include <mpc83xx.h>
-#include <fsl_esdhc.h>
-#include <asm/io.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_mpc83xx_serdes.h>
-
-#include "mpc8308.h"
-
-#include <gdsys_fpga.h>
-
-#include "../common/adv7611.h"
-#include "../common/ch7301.h"
-#include "../common/dp501.h"
-#include "../common/ioep-fpga.h"
-#include "../common/mclink.h"
-#include "../common/osd.h"
-#include "../common/phy.h"
-#include "../common/fanctrl.h"
-
-#include <pca953x.h>
-#include <pca9698.h>
-
-#include <miiphy.h>
-
-#define MAX_MUX_CHANNELS 2
-
-enum {
- MCFPGA_DONE = 1 << 0,
- MCFPGA_INIT_N = 1 << 1,
- MCFPGA_PROGRAM_N = 1 << 2,
- MCFPGA_UPDATE_ENABLE_N = 1 << 3,
- MCFPGA_RESET_N = 1 << 4,
-};
-
-enum {
- GPIO_MDC = 1 << 14,
- GPIO_MDIO = 1 << 15,
-};
-
-uint mclink_fpgacount;
-struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;
-
-struct {
- u8 bus;
- u8 addr;
-} strider_fans[] = CONFIG_STRIDER_FANS;
-
-int fpga_set_reg(u32 fpga, u16 *reg, off_t regoff, u16 data)
-{
- int res;
-
- switch (fpga) {
- case 0:
- out_le16(reg, data);
- break;
- default:
- res = mclink_send(fpga - 1, regoff, data);
- if (res < 0) {
- printf("mclink_send reg %02lx data %04x returned %d\n",
- regoff, data, res);
- return res;
- }
- break;
- }
-
- return 0;
-}
-
-int fpga_get_reg(u32 fpga, u16 *reg, off_t regoff, u16 *data)
-{
- int res;
-
- switch (fpga) {
- case 0:
- *data = in_le16(reg);
- break;
- default:
- if (fpga > mclink_fpgacount)
- return -EINVAL;
- res = mclink_receive(fpga - 1, regoff, data);
- if (res < 0) {
- printf("mclink_receive reg %02lx returned %d\n",
- regoff, res);
- return res;
- }
- }
-
- return 0;
-}
-
-int checkboard(void)
-{
- char *s = env_get("serial#");
- bool hw_type_cat = pca9698_get_value(0x20, 18);
-
- puts("Board: ");
-
- printf("Strider %s", hw_type_cat ? "CAT" : "Fiber");
-
- if (s) {
- puts(", serial# ");
- puts(s);
- }
-
- puts("\n");
-
- return 0;
-}
-
-int last_stage_init(void)
-{
- int slaves;
- uint k;
- uint mux_ch;
- uchar mclink_controllers_dvi[] = { 0x3c, 0x3d, 0x3e };
-#ifdef CONFIG_STRIDER_CPU
- uchar mclink_controllers_dp[] = { 0x24, 0x25, 0x26 };
-#endif
- bool hw_type_cat = pca9698_get_value(0x20, 18);
-#ifdef CONFIG_STRIDER_CON_DP
- bool is_dh = pca9698_get_value(0x20, 25);
-#endif
- bool ch0_sgmii2_present;
-
- /* Turn on Analog Devices ADV7611 */
- pca9698_direction_output(0x20, 8, 0);
-
- /* Turn on Parade DP501 */
- pca9698_direction_output(0x20, 10, 1);
- pca9698_direction_output(0x20, 11, 1);
-
- ch0_sgmii2_present = !pca9698_get_value(0x20, 37);
-
- /* wait for FPGA done, then reset FPGA */
- for (k = 0; k < ARRAY_SIZE(mclink_controllers_dvi); ++k) {
- uint ctr = 0;
- uchar *mclink_controllers = mclink_controllers_dvi;
-
-#ifdef CONFIG_STRIDER_CPU
- if (i2c_probe(mclink_controllers[k])) {
- mclink_controllers = mclink_controllers_dp;
- if (i2c_probe(mclink_controllers[k]))
- continue;
- }
-#else
- if (i2c_probe(mclink_controllers[k]))
- continue;
-#endif
- while (!(pca953x_get_val(mclink_controllers[k])
- & MCFPGA_DONE)) {
- mdelay(100);
- if (ctr++ > 5) {
- printf("no done for mclink_controller %d\n", k);
- break;
- }
- }
-
- pca953x_set_dir(mclink_controllers[k], MCFPGA_RESET_N, 0);
- pca953x_set_val(mclink_controllers[k], MCFPGA_RESET_N, 0);
- udelay(10);
- pca953x_set_val(mclink_controllers[k], MCFPGA_RESET_N,
- MCFPGA_RESET_N);
- }
-
- if (hw_type_cat) {
- int retval;
- struct mii_dev *mdiodev = mdio_alloc();
-
- if (!mdiodev)
- return -ENOMEM;
- strncpy(mdiodev->name, bb_miiphy_buses[0].name, MDIO_NAME_LEN);
- mdiodev->read = bb_miiphy_read;
- mdiodev->write = bb_miiphy_write;
-
- retval = mdio_register(mdiodev);
- if (retval < 0)
- return retval;
- for (mux_ch = 0; mux_ch < MAX_MUX_CHANNELS; ++mux_ch) {
- if ((mux_ch == 1) && !ch0_sgmii2_present)
- continue;
-
- setup_88e1514(bb_miiphy_buses[0].name, mux_ch);
- }
- }
-
- /* give slave-PLLs and Parade DP501 some time to be up and running */
- mdelay(500);
-
- mclink_fpgacount = CONFIG_SYS_MCLINK_MAX;
- slaves = mclink_probe();
- mclink_fpgacount = 0;
-
- ioep_fpga_print_info(0);
-
- if (!adv7611_probe(0))
- printf(" Advantiv ADV7611 HDMI Receiver\n");
-
-#ifdef CONFIG_STRIDER_CON
- if (ioep_fpga_has_osd(0))
- osd_probe(0);
-#endif
-
-#ifdef CONFIG_STRIDER_CON_DP
- if (ioep_fpga_has_osd(0)) {
- osd_probe(0);
- if (is_dh)
- osd_probe(4);
- }
-#endif
-
-#ifdef CONFIG_STRIDER_CPU
- ch7301_probe(0, false);
- dp501_probe(0, false);
-#endif
-
- if (slaves <= 0)
- return 0;
-
- mclink_fpgacount = slaves;
-
-#ifdef CONFIG_STRIDER_CPU
- /* get ADV7611 out of reset, power up DP501, give some time to wakeup */
- for (k = 1; k <= slaves; ++k)
- FPGA_SET_REG(k, extended_control, 0x10); /* enable video */
-
- mdelay(500);
-#endif
-
- for (k = 1; k <= slaves; ++k) {
- ioep_fpga_print_info(k);
-#ifdef CONFIG_STRIDER_CON
- if (ioep_fpga_has_osd(k))
- osd_probe(k);
-#endif
-#ifdef CONFIG_STRIDER_CON_DP
- if (ioep_fpga_has_osd(k)) {
- osd_probe(k);
- if (is_dh)
- osd_probe(k + 4);
- }
-#endif
-#ifdef CONFIG_STRIDER_CPU
- if (!adv7611_probe(k))
- printf(" Advantiv ADV7611 HDMI Receiver\n");
- ch7301_probe(k, false);
- dp501_probe(k, false);
-#endif
- if (hw_type_cat) {
- int retval;
- struct mii_dev *mdiodev = mdio_alloc();
-
- if (!mdiodev)
- return -ENOMEM;
- strncpy(mdiodev->name, bb_miiphy_buses[k].name,
- MDIO_NAME_LEN);
- mdiodev->read = bb_miiphy_read;
- mdiodev->write = bb_miiphy_write;
-
- retval = mdio_register(mdiodev);
- if (retval < 0)
- return retval;
- setup_88e1514(bb_miiphy_buses[k].name, 0);
- }
- }
-
- for (k = 0; k < ARRAY_SIZE(strider_fans); ++k) {
- i2c_set_bus_num(strider_fans[k].bus);
- init_fan_controller(strider_fans[k].addr);
- }
-
- return 0;
-}
-
-/*
- * provide access to fpga gpios (for I2C bitbang)
- * (these may look all too simple but make iocon.h much more readable)
- */
-void fpga_gpio_set(uint bus, int pin)
-{
- FPGA_SET_REG(bus, gpio.set, pin);
-}
-
-void fpga_gpio_clear(uint bus, int pin)
-{
- FPGA_SET_REG(bus, gpio.clear, pin);
-}
-
-int fpga_gpio_get(uint bus, int pin)
-{
- u16 val;
-
- FPGA_GET_REG(bus, gpio.read, &val);
-
- return val & pin;
-}
-
-#ifdef CONFIG_STRIDER_CON_DP
-void fpga_control_set(uint bus, int pin)
-{
- u16 val;
-
- FPGA_GET_REG(bus, control, &val);
- FPGA_SET_REG(bus, control, val | pin);
-}
-
-void fpga_control_clear(uint bus, int pin)
-{
- u16 val;
-
- FPGA_GET_REG(bus, control, &val);
- FPGA_SET_REG(bus, control, val & ~pin);
-}
-#endif
-
-void mpc8308_init(void)
-{
- pca9698_direction_output(0x20, 26, 1);
-}
-
-void mpc8308_set_fpga_reset(uint state)
-{
- pca9698_set_value(0x20, 26, state ? 0 : 1);
-}
-
-void mpc8308_setup_hw(void)
-{
- immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
-
- /*
- * set "startup-finished"-gpios
- */
- setbits_be32(&immr->gpio[0].dir, BIT(31 - 11) | BIT(31 - 12));
- setbits_gpio0_out(BIT(31 - 12));
-}
-
-int mpc8308_get_fpga_done(uint fpga)
-{
- return pca9698_get_value(0x20, 20);
-}
-
-#ifdef CONFIG_FSL_ESDHC
-int board_mmc_init(struct bd_info *bd)
-{
- immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- sysconf83xx_t *sysconf = &immr->sysconf;
-
- /* Enable cache snooping in eSDHC system configuration register */
- out_be32(&sysconf->sdhccr, 0x02000000);
-
- return fsl_esdhc_mmc_init(bd);
-}
-#endif
-
-static struct pci_region pcie_regions_0[] = {
- {
- .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
- .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
- .size = CONFIG_SYS_PCIE1_MEM_SIZE,
- .flags = PCI_REGION_MEM,
- },
- {
- .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
- .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
- .size = CONFIG_SYS_PCIE1_IO_SIZE,
- .flags = PCI_REGION_IO,
- },
-};
-
-void pci_init_board(void)
-{
- immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- sysconf83xx_t *sysconf = &immr->sysconf;
- law83xx_t *pcie_law = sysconf->pcielaw;
- struct pci_region *pcie_reg[] = { pcie_regions_0 };
-
- fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
-
- /* Deassert the resets in the control register */
- out_be32(&sysconf->pecr1, 0xE0008000);
- udelay(2000);
-
- /* Configure PCI Express Local Access Windows */
- out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
- out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
-
- mpc83xx_pcie_init(1, pcie_reg);
-}
-
-ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
-{
- info->portwidth = FLASH_CFI_16BIT;
- info->chipwidth = FLASH_CFI_BY16;
- info->interface = FLASH_CFI_X16;
- return 1;
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
- ft_cpu_setup(blob, bd);
- fsl_fdt_fixup_dr_usb(blob, bd);
- fdt_fixup_esdhc(blob, bd);
-
- return 0;
-}
-#endif
-
-/*
- * FPGA MII bitbang implementation
- */
-
-struct fpga_mii {
- uint fpga;
- int mdio;
-} fpga_mii[] = {
- { 0, 1},
- { 1, 1},
- { 2, 1},
- { 3, 1},
-};
-
-static int mii_dummy_init(struct bb_miiphy_bus *bus)
-{
- return 0;
-}
-
-static int mii_mdio_active(struct bb_miiphy_bus *bus)
-{
- struct fpga_mii *fpga_mii = bus->priv;
-
- if (fpga_mii->mdio)
- FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
- else
- FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
-
- return 0;
-}
-
-static int mii_mdio_tristate(struct bb_miiphy_bus *bus)
-{
- struct fpga_mii *fpga_mii = bus->priv;
-
- FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
-
- return 0;
-}
-
-static int mii_set_mdio(struct bb_miiphy_bus *bus, int v)
-{
- struct fpga_mii *fpga_mii = bus->priv;
-
- if (v)
- FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDIO);
- else
- FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDIO);
-
- fpga_mii->mdio = v;
-
- return 0;
-}
-
-static int mii_get_mdio(struct bb_miiphy_bus *bus, int *v)
-{
- u16 gpio;
- struct fpga_mii *fpga_mii = bus->priv;
-
- FPGA_GET_REG(fpga_mii->fpga, gpio.read, &gpio);
-
- *v = ((gpio & GPIO_MDIO) != 0);
-
- return 0;
-}
-
-static int mii_set_mdc(struct bb_miiphy_bus *bus, int v)
-{
- struct fpga_mii *fpga_mii = bus->priv;
-
- if (v)
- FPGA_SET_REG(fpga_mii->fpga, gpio.set, GPIO_MDC);
- else
- FPGA_SET_REG(fpga_mii->fpga, gpio.clear, GPIO_MDC);
-
- return 0;
-}
-
-static int mii_delay(struct bb_miiphy_bus *bus)
-{
- udelay(1);
-
- return 0;
-}
-
-struct bb_miiphy_bus bb_miiphy_buses[] = {
- {
- .name = "board0",
- .init = mii_dummy_init,
- .mdio_active = mii_mdio_active,
- .mdio_tristate = mii_mdio_tristate,
- .set_mdio = mii_set_mdio,
- .get_mdio = mii_get_mdio,
- .set_mdc = mii_set_mdc,
- .delay = mii_delay,
- .priv = &fpga_mii[0],
- },
- {
- .name = "board1",
- .init = mii_dummy_init,
- .mdio_active = mii_mdio_active,
- .mdio_tristate = mii_mdio_tristate,
- .set_mdio = mii_set_mdio,
- .get_mdio = mii_get_mdio,
- .set_mdc = mii_set_mdc,
- .delay = mii_delay,
- .priv = &fpga_mii[1],
- },
- {
- .name = "board2",
- .init = mii_dummy_init,
- .mdio_active = mii_mdio_active,
- .mdio_tristate = mii_mdio_tristate,
- .set_mdio = mii_set_mdio,
- .get_mdio = mii_get_mdio,
- .set_mdc = mii_set_mdc,
- .delay = mii_delay,
- .priv = &fpga_mii[2],
- },
- {
- .name = "board3",
- .init = mii_dummy_init,
- .mdio_active = mii_mdio_active,
- .mdio_tristate = mii_mdio_tristate,
- .set_mdio = mii_set_mdio,
- .get_mdio = mii_get_mdio,
- .set_mdc = mii_set_mdc,
- .delay = mii_delay,
- .priv = &fpga_mii[3],
- },
-};
-
-int bb_miiphy_buses_num = ARRAY_SIZE(bb_miiphy_buses);
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFE000000
-CONFIG_SYS_MEMTEST_START=0x00001000
-CONFIG_SYS_MEMTEST_END=0x07f00000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_IDENT_STRING=" strider con 0.01"
-CONFIG_SYS_CLK_FREQ=33333333
-CONFIG_MPC83xx=y
-CONFIG_TARGET_STRIDER=y
-CONFIG_SYSTEM_PLL_VCO_DIV_2=y
-CONFIG_SYSTEM_PLL_FACTOR_4_1=y
-CONFIG_CORE_PLL_RATIO_3_1=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC2_MODE_RGMII=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="DDR"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_128_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="IMMRBAR"
-CONFIG_BAT1_BASE=0xE0000000
-CONFIG_BAT1_LENGTH_8_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_INHIBITED=y
-CONFIG_BAT1_ICACHE_GUARDED=y
-CONFIG_BAT1_DCACHE_INHIBITED=y
-CONFIG_BAT1_DCACHE_GUARDED=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="FLASH"
-CONFIG_BAT2_BASE=0xFE000000
-CONFIG_BAT2_LENGTH_8_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="STACK_IN_DCACHE"
-CONFIG_BAT3_BASE=0xE6000000
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFE000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_8_MBYTES=y
-CONFIG_LBLAW1=y
-CONFIG_LBLAW1_BASE=0xE0600000
-CONFIG_LBLAW1_NAME="FPGA0"
-CONFIG_LBLAW1_LENGTH_1_MBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFE000000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_8_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_ELBC_BR1_OR1=y
-CONFIG_BR1_OR1_NAME="FPGA"
-CONFIG_BR1_OR1_BASE=0xE0600000
-CONFIG_BR1_PORTSIZE_16BIT=y
-CONFIG_OR1_AM_1_MBYTES=y
-CONFIG_OR1_XAM_SET=y
-CONFIG_OR1_SCY_5=y
-CONFIG_OR1_CSNT_EARLIER=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_DPM=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_SICR_IEEE1588_A_GPIO=y
-CONFIG_SICR_GTM_GPIO=y
-CONFIG_SICR_ETSEC2_GPIO=y
-CONFIG_SICR_GPIOSEL_IEEE1588=y
-CONFIG_SICR_TMSOBI1_2_5_V=y
-CONFIG_SICR_TMSOBI2_2_5_V=y
-CONFIG_ACR_PIPE_DEP_4=y
-CONFIG_ACR_RPTCNT_4=y
-CONFIG_SPCR_TSECEP_3=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_2=y
-CONFIG_CMD_IOLOOP=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="STRIDER_CON"
-CONFIG_BOOTDELAY=5
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_USE_PREBOOT=y
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_LAST_STAGE_INIT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_CMD_FPGAD=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_DOS_PARTITION=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0xFE060000
-CONFIG_ENV_ADDR_REDUND=0xFE070000
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_PROTECTION=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_BITBANGMII=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_CONS_INDEX=2
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFE000000
-CONFIG_SYS_MEMTEST_START=0x00001000
-CONFIG_SYS_MEMTEST_END=0x07f00000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_IDENT_STRING=" strider con dp 0.01"
-CONFIG_SYS_CLK_FREQ=33333333
-CONFIG_MPC83xx=y
-CONFIG_TARGET_STRIDER=y
-CONFIG_SYSTEM_PLL_VCO_DIV_2=y
-CONFIG_SYSTEM_PLL_FACTOR_4_1=y
-CONFIG_CORE_PLL_RATIO_3_1=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC2_MODE_RGMII=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="DDR"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_128_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="IMMRBAR"
-CONFIG_BAT1_BASE=0xE0000000
-CONFIG_BAT1_LENGTH_8_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_INHIBITED=y
-CONFIG_BAT1_ICACHE_GUARDED=y
-CONFIG_BAT1_DCACHE_INHIBITED=y
-CONFIG_BAT1_DCACHE_GUARDED=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="FLASH"
-CONFIG_BAT2_BASE=0xFE000000
-CONFIG_BAT2_LENGTH_8_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="STACK_IN_DCACHE"
-CONFIG_BAT3_BASE=0xE6000000
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFE000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_8_MBYTES=y
-CONFIG_LBLAW1=y
-CONFIG_LBLAW1_BASE=0xE0600000
-CONFIG_LBLAW1_NAME="FPGA0"
-CONFIG_LBLAW1_LENGTH_1_MBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFE000000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_8_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_ELBC_BR1_OR1=y
-CONFIG_BR1_OR1_NAME="FPGA"
-CONFIG_BR1_OR1_BASE=0xE0600000
-CONFIG_BR1_PORTSIZE_16BIT=y
-CONFIG_OR1_AM_1_MBYTES=y
-CONFIG_OR1_XAM_SET=y
-CONFIG_OR1_SCY_5=y
-CONFIG_OR1_CSNT_EARLIER=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_DPM=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_SICR_IEEE1588_A_GPIO=y
-CONFIG_SICR_GTM_GPIO=y
-CONFIG_SICR_ETSEC2_GPIO=y
-CONFIG_SICR_GPIOSEL_IEEE1588=y
-CONFIG_SICR_TMSOBI1_2_5_V=y
-CONFIG_SICR_TMSOBI2_2_5_V=y
-CONFIG_ACR_PIPE_DEP_4=y
-CONFIG_ACR_RPTCNT_4=y
-CONFIG_SPCR_TSECEP_3=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_2=y
-CONFIG_CMD_IOLOOP=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="STRIDER_CON_DP"
-CONFIG_BOOTDELAY=5
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_USE_PREBOOT=y
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_LAST_STAGE_INIT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_CMD_FPGAD=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_DOS_PARTITION=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0xFE060000
-CONFIG_ENV_ADDR_REDUND=0xFE070000
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_PROTECTION=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_BITBANGMII=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_CONS_INDEX=2
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFE000000
-CONFIG_SYS_MEMTEST_START=0x00001000
-CONFIG_SYS_MEMTEST_END=0x07f00000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_IDENT_STRING=" strider cpu 0.01"
-CONFIG_SYS_CLK_FREQ=33333333
-CONFIG_MPC83xx=y
-CONFIG_TARGET_STRIDER=y
-CONFIG_SYSTEM_PLL_VCO_DIV_2=y
-CONFIG_SYSTEM_PLL_FACTOR_4_1=y
-CONFIG_CORE_PLL_RATIO_3_1=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC2_MODE_RGMII=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="DDR"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_128_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="IMMRBAR"
-CONFIG_BAT1_BASE=0xE0000000
-CONFIG_BAT1_LENGTH_8_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_INHIBITED=y
-CONFIG_BAT1_ICACHE_GUARDED=y
-CONFIG_BAT1_DCACHE_INHIBITED=y
-CONFIG_BAT1_DCACHE_GUARDED=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="FLASH"
-CONFIG_BAT2_BASE=0xFE000000
-CONFIG_BAT2_LENGTH_8_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="STACK_IN_DCACHE"
-CONFIG_BAT3_BASE=0xE6000000
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFE000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_8_MBYTES=y
-CONFIG_LBLAW1=y
-CONFIG_LBLAW1_BASE=0xE0600000
-CONFIG_LBLAW1_NAME="FPGA0"
-CONFIG_LBLAW1_LENGTH_1_MBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFE000000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_8_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_ELBC_BR1_OR1=y
-CONFIG_BR1_OR1_NAME="FPGA"
-CONFIG_BR1_OR1_BASE=0xE0600000
-CONFIG_BR1_PORTSIZE_16BIT=y
-CONFIG_OR1_AM_1_MBYTES=y
-CONFIG_OR1_XAM_SET=y
-CONFIG_OR1_SCY_5=y
-CONFIG_OR1_CSNT_EARLIER=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_DPM=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_SICR_IEEE1588_A_GPIO=y
-CONFIG_SICR_GTM_GPIO=y
-CONFIG_SICR_ETSEC2_GPIO=y
-CONFIG_SICR_GPIOSEL_IEEE1588=y
-CONFIG_SICR_TMSOBI1_2_5_V=y
-CONFIG_SICR_TMSOBI2_2_5_V=y
-CONFIG_ACR_PIPE_DEP_4=y
-CONFIG_ACR_RPTCNT_4=y
-CONFIG_SPCR_TSECEP_3=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_2=y
-CONFIG_CMD_IOLOOP=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="STRIDER_CPU"
-CONFIG_BOOTDELAY=5
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_USE_PREBOOT=y
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_LAST_STAGE_INIT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_CMD_FPGAD=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_DOS_PARTITION=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0xFE060000
-CONFIG_ENV_ADDR_REDUND=0xFE070000
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_PROTECTION=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_BITBANGMII=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_CONS_INDEX=2
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFE000000
-CONFIG_SYS_MEMTEST_START=0x00001000
-CONFIG_SYS_MEMTEST_END=0x07f00000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_IDENT_STRING=" strider cpu dp 0.01"
-CONFIG_SYS_CLK_FREQ=33333333
-CONFIG_MPC83xx=y
-CONFIG_TARGET_STRIDER=y
-CONFIG_SYSTEM_PLL_VCO_DIV_2=y
-CONFIG_SYSTEM_PLL_FACTOR_4_1=y
-CONFIG_CORE_PLL_RATIO_3_1=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_TSEC2_MODE_RGMII=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="DDR"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_128_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="IMMRBAR"
-CONFIG_BAT1_BASE=0xE0000000
-CONFIG_BAT1_LENGTH_8_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_INHIBITED=y
-CONFIG_BAT1_ICACHE_GUARDED=y
-CONFIG_BAT1_DCACHE_INHIBITED=y
-CONFIG_BAT1_DCACHE_GUARDED=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="FLASH"
-CONFIG_BAT2_BASE=0xFE000000
-CONFIG_BAT2_LENGTH_8_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="STACK_IN_DCACHE"
-CONFIG_BAT3_BASE=0xE6000000
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFE000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_8_MBYTES=y
-CONFIG_LBLAW1=y
-CONFIG_LBLAW1_BASE=0xE0600000
-CONFIG_LBLAW1_NAME="FPGA0"
-CONFIG_LBLAW1_LENGTH_1_MBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFE000000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_8_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_15=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_ELBC_BR1_OR1=y
-CONFIG_BR1_OR1_NAME="FPGA"
-CONFIG_BR1_OR1_BASE=0xE0600000
-CONFIG_BR1_PORTSIZE_16BIT=y
-CONFIG_OR1_AM_1_MBYTES=y
-CONFIG_OR1_XAM_SET=y
-CONFIG_OR1_SCY_5=y
-CONFIG_OR1_CSNT_EARLIER=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_DPM=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_SICR_IEEE1588_A_GPIO=y
-CONFIG_SICR_GTM_GPIO=y
-CONFIG_SICR_ETSEC2_GPIO=y
-CONFIG_SICR_GPIOSEL_IEEE1588=y
-CONFIG_SICR_TMSOBI1_2_5_V=y
-CONFIG_SICR_TMSOBI2_2_5_V=y
-CONFIG_ACR_PIPE_DEP_4=y
-CONFIG_ACR_RPTCNT_4=y
-CONFIG_SPCR_TSECEP_3=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_2=y
-CONFIG_CMD_IOLOOP=y
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="STRIDER_CPU,STRIDER_CPU_DP"
-CONFIG_BOOTDELAY=5
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_USE_PREBOOT=y
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_LAST_STAGE_INIT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_SYS_ALT_MEMTEST=y
-CONFIG_CMD_FPGAD=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_DOS_PARTITION=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0xFE060000
-CONFIG_ENV_ADDR_REDUND=0xFE070000
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_PROTECTION=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_BITBANGMII=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_CONS_INDEX=2
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2014
- * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <linux/stringify.h>
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
-
-/*
- * SERDES
- */
-#define CONFIG_FSL_SERDES
-#define CONFIG_FSL_SERDES1 0xe3000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
- | DDRCDR_PZ_LOZ \
- | DDRCDR_NZ_LOZ \
- | DDRCDR_ODT \
- | DDRCDR_Q_DRN)
- /* 0x7b880001 */
-/*
- * Manually set up DDR parameters
- * consist of one chip NT5TU64M16HG from NANYA
- */
-
-#define CONFIG_SYS_DDR_SIZE 128 /* MB */
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
- | CSCONFIG_ODT_RD_NEVER \
- | CSCONFIG_ODT_WR_ONLY_CURRENT \
- | CSCONFIG_BANK_BIT_3 \
- | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
- /* 0x80010102 */
-#define CONFIG_SYS_DDR_TIMING_3 0
-#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
- | (0 << TIMING_CFG0_WRT_SHIFT) \
- | (0 << TIMING_CFG0_RRT_SHIFT) \
- | (0 << TIMING_CFG0_WWT_SHIFT) \
- | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
- | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
- | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
- | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
- /* 0x00260802 */
-#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
- | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
- | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
- | (7 << TIMING_CFG1_CASLAT_SHIFT) \
- | (9 << TIMING_CFG1_REFREC_SHIFT) \
- | (2 << TIMING_CFG1_WRREC_SHIFT) \
- | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
- | (2 << TIMING_CFG1_WRTORD_SHIFT))
- /* 0x26279222 */
-#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
- | (4 << TIMING_CFG2_CPO_SHIFT) \
- | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
- | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
- | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
- | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
- | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
- /* 0x021848c5 */
-#define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \
- | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
- /* 0x08240100 */
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
- | SDRAM_CFG_SDRAM_TYPE_DDR2 \
- | SDRAM_CFG_DBW_16)
- /* 0x43100000 */
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
-#define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
- | (0x0242 << SDRAM_MODE_SD_SHIFT))
- /* ODT 150ohm CL=4, AL=0 on SDRAM */
-#define CONFIG_SYS_DDR_MODE2 0x00000000
-
-/*
- * Memory test
- */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-#define CONFIG_FLASH_CFI_LEGACY
-#define CONFIG_SYS_FLASH_LEGACY_512Kx16
-
-#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
-#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 135
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FPGA_DONE(k) 0x0010
-
-#define CONFIG_SYS_FPGA_COUNT 1
-
-#define CONFIG_SYS_MCLINK_MAX 3
-
-#define CONFIG_SYS_FPGA_PTR \
- { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }
-
-#define CONFIG_SYS_FPGA_NO_RFL_HI
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
-
-/* Pass open firmware flat tree */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-
-#define CONFIG_PCA953X /* NXP PCA9554 */
-#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x24, 16}, {0x25, 16}, {0x26, 16}, \
- {0x3c, 8}, {0x3d, 8}, {0x3e, 8} }
-
-#define CONFIG_PCA9698 /* NXP PCA9698 */
-
-#define CONFIG_SYS_I2C_IHS
-#define CONFIG_SYS_I2C_IHS_CH0
-#define CONFIG_SYS_I2C_IHS_SPEED_0 50000
-#define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F
-#define CONFIG_SYS_I2C_IHS_CH1
-#define CONFIG_SYS_I2C_IHS_SPEED_1 50000
-#define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F
-#define CONFIG_SYS_I2C_IHS_CH2
-#define CONFIG_SYS_I2C_IHS_SPEED_2 50000
-#define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F
-#define CONFIG_SYS_I2C_IHS_CH3
-#define CONFIG_SYS_I2C_IHS_SPEED_3 50000
-#define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F
-
-#ifdef CONFIG_STRIDER_CON_DP
-#define CONFIG_SYS_I2C_IHS_DUAL
-#define CONFIG_SYS_I2C_IHS_CH0_1
-#define CONFIG_SYS_I2C_IHS_SPEED_0_1 50000
-#define CONFIG_SYS_I2C_IHS_SLAVE_0_1 0x7F
-#define CONFIG_SYS_I2C_IHS_CH1_1
-#define CONFIG_SYS_I2C_IHS_SPEED_1_1 50000
-#define CONFIG_SYS_I2C_IHS_SLAVE_1_1 0x7F
-#define CONFIG_SYS_I2C_IHS_CH2_1
-#define CONFIG_SYS_I2C_IHS_SPEED_2_1 50000
-#define CONFIG_SYS_I2C_IHS_SLAVE_2_1 0x7F
-#define CONFIG_SYS_I2C_IHS_CH3_1
-#define CONFIG_SYS_I2C_IHS_SPEED_3_1 50000
-#define CONFIG_SYS_I2C_IHS_SLAVE_3_1 0x7F
-#endif
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define CONFIG_SYS_I2C_SOFT
-#define CONFIG_SOFT_I2C_READ_REPEATED_START
-#define CONFIG_SYS_I2C_SOFT_SPEED 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
-#define I2C_SOFT_DECLARATIONS2
-#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F
-#define I2C_SOFT_DECLARATIONS3
-#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F
-#define I2C_SOFT_DECLARATIONS4
-#define CONFIG_SYS_I2C_SOFT_SPEED_4 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F
-#if defined(CONFIG_STRIDER_CON) || defined(CONFIG_STRIDER_CON_DP)
-#define I2C_SOFT_DECLARATIONS5
-#define CONFIG_SYS_I2C_SOFT_SPEED_5 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_5 0x7F
-#define I2C_SOFT_DECLARATIONS6
-#define CONFIG_SYS_I2C_SOFT_SPEED_6 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_6 0x7F
-#define I2C_SOFT_DECLARATIONS7
-#define CONFIG_SYS_I2C_SOFT_SPEED_7 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_7 0x7F
-#define I2C_SOFT_DECLARATIONS8
-#define CONFIG_SYS_I2C_SOFT_SPEED_8 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_8 0x7F
-#endif
-#ifdef CONFIG_STRIDER_CON_DP
-#define I2C_SOFT_DECLARATIONS9
-#define CONFIG_SYS_I2C_SOFT_SPEED_9 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_9 0x7F
-#define I2C_SOFT_DECLARATIONS10
-#define CONFIG_SYS_I2C_SOFT_SPEED_10 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_10 0x7F
-#define I2C_SOFT_DECLARATIONS11
-#define CONFIG_SYS_I2C_SOFT_SPEED_11 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_11 0x7F
-#define I2C_SOFT_DECLARATIONS12
-#define CONFIG_SYS_I2C_SOFT_SPEED_12 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_12 0x7F
-#endif
-
-#ifdef CONFIG_STRIDER_CON
-#define CONFIG_SYS_ICS8N3QV01_I2C {5, 6, 7, 8}
-#define CONFIG_SYS_CH7301_I2C {5, 6, 7, 8}
-#define CONFIG_SYS_ADV7611_I2C {5, 6, 7, 8}
-#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4}
-#define CONFIG_STRIDER_FANS { {10, 0x4c}, {11, 0x4c}, \
- {12, 0x4c} }
-#elif defined(CONFIG_STRIDER_CON_DP)
-#define CONFIG_SYS_ICS8N3QV01_I2C {13, 14, 15, 16, 17, 18, 19, 20}
-#define CONFIG_SYS_CH7301_I2C {1, 3, 5, 7}
-#define CONFIG_SYS_ADV7611_I2C {1, 3, 5, 7}
-#define CONFIG_SYS_DP501_I2C {1, 3, 5, 7, 2, 4, 6, 8}
-#define CONFIG_STRIDER_FANS { {10, 0x4c}, {11, 0x4c}, \
- {12, 0x4c} }
-#elif defined(CONFIG_STRIDER_CPU_DP)
-#define CONFIG_SYS_CH7301_I2C {1, 2, 3, 4}
-#define CONFIG_SYS_ADV7611_I2C {1, 2, 3, 4}
-#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4}
-#define CONFIG_STRIDER_FANS { {6, 0x4c}, {7, 0x4c}, \
- {8, 0x4c} }
-#else
-#define CONFIG_SYS_CH7301_I2C {1, 2, 3, 4}
-#define CONFIG_SYS_ADV7611_I2C {1, 2, 3, 4}
-#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4}
-#define CONFIG_STRIDER_FANS { {2, 0x18}, {3, 0x18}, \
- {4, 0x18} }
-#endif
-
-#ifndef __ASSEMBLY__
-void fpga_gpio_set(unsigned int bus, int pin);
-void fpga_gpio_clear(unsigned int bus, int pin);
-int fpga_gpio_get(unsigned int bus, int pin);
-void fpga_control_set(unsigned int bus, int pin);
-void fpga_control_clear(unsigned int bus, int pin);
-#endif
-
-#ifdef CONFIG_STRIDER_CON
-#define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0200 : 0x0040)
-#define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0100 : 0x0020)
-#define I2C_FPGA_IDX ((I2C_ADAP_HWNR > 3) ? \
- (I2C_ADAP_HWNR - 4) : I2C_ADAP_HWNR)
-#elif defined(CONFIG_STRIDER_CON_DP)
-#define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200)
-#define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100)
-#define I2C_FPGA_IDX (I2C_ADAP_HWNR % 4)
-#else
-#define I2C_SDA_GPIO 0x0040
-#define I2C_SCL_GPIO 0x0020
-#define I2C_FPGA_IDX I2C_ADAP_HWNR
-#endif
-
-#ifdef CONFIG_STRIDER_CON_DP
-#define I2C_ACTIVE \
- do { \
- if (I2C_ADAP_HWNR > 7) \
- fpga_control_set(I2C_FPGA_IDX, 0x0004); \
- else \
- fpga_control_clear(I2C_FPGA_IDX, 0x0004); \
- } while (0)
-#else
-#define I2C_ACTIVE { }
-#endif
-
-#define I2C_TRISTATE { }
-#define I2C_READ \
- (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0)
-#define I2C_SDA(bit) \
- do { \
- if (bit) \
- fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \
- else \
- fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \
- } while (0)
-#define I2C_SCL(bit) \
- do { \
- if (bit) \
- fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \
- else \
- fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \
- } while (0)
-#define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */
-
-/*
- * Software (bit-bang) MII driver configuration
- */
-#define CONFIG_BITBANGMII_MULTI
-
-/*
- * OSD Setup
- */
-#define CONFIG_SYS_OSD_SCREENS 1
-#define CONFIG_SYS_DP501_DIFFERENTIAL
-#define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */
-
-#ifdef CONFIG_STRIDER_CON_DP
-#define CONFIG_SYS_OSD_DH
-#endif
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCIE1_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
-#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
-#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
-
-/* enable PCIE clock */
-#define CONFIG_SYS_SCCR_PCIEXP1CM 1
-
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCIE
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
-
-/*
- * TSEC
- */
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-
-/*
- * TSEC ethernet configuration
- */
-#define CONFIG_TSEC1
-#define CONFIG_TSEC1_NAME "eTSEC0"
-#define TSEC1_PHY_ADDR 1
-#define TSEC1_PHYIDX 0
-#define TSEC1_FLAGS 0
-
-/* Options are: eTSEC[0-1] */
-#define CONFIG_ETHPRIME "eTSEC0"
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
-
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#endif
-
-#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-
-
-#define CONFIG_HOSTNAME "hrcon"
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS1\0" \
- "u-boot=u-boot.bin\0" \
- "kernel_addr=1000000\0" \
- "fdt_addr=C00000\0" \
- "fdtfile=hrcon.dtb\0" \
- "load=tftp ${loadaddr} ${u-boot}\0" \
- "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
- " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
- " +${filesize};cp.b ${fileaddr} " \
- __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
- "upd=run load update\0" \
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp ${kernel_addr} $bootfile;" \
- "tftp ${fdt_addr} $fdtfile;" \
- "bootm ${kernel_addr} - ${fdt_addr}"
-
-#define CONFIG_MMCBOOTCOMMAND \
- "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "ext2load mmc 0:2 ${kernel_addr} $bootfile;" \
- "ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \
- "bootm ${kernel_addr} - ${fdt_addr}"
-
-#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
-
-#endif /* __CONFIG_H */
};
#endif
-#if defined(CONFIG_TARGET_HRCON) || defined(CONFIG_STRIDER_CON_DP)
+#if defined(CONFIG_TARGET_HRCON)
struct ihs_fpga {
u16 reflection_low; /* 0x0000 */
u16 versions; /* 0x0002 */
};
#endif
-#ifdef CONFIG_STRIDER_CPU
-struct ihs_fpga {
- u16 reflection_low; /* 0x0000 */
- u16 versions; /* 0x0002 */
- u16 fpga_version; /* 0x0004 */
- u16 fpga_features; /* 0x0006 */
- u16 reserved_0[1]; /* 0x0008 */
- u16 top_interrupt; /* 0x000a */
- u16 reserved_1[3]; /* 0x000c */
- u16 extended_control; /* 0x0012 */
- struct ihs_gpio gpio; /* 0x0014 */
- u16 mpc3w_control; /* 0x001a */
- u16 reserved_2[2]; /* 0x001c */
- struct ihs_io_ep ep; /* 0x0020 */
- u16 reserved_3[9]; /* 0x002e */
- u16 mc_int; /* 0x0040 */
- u16 mc_int_en; /* 0x0042 */
- u16 mc_status; /* 0x0044 */
- u16 mc_control; /* 0x0046 */
- u16 mc_tx_data; /* 0x0048 */
- u16 mc_tx_address; /* 0x004a */
- u16 mc_tx_cmd; /* 0x004c */
- u16 mc_res; /* 0x004e */
- u16 mc_rx_cmd_status; /* 0x0050 */
- u16 mc_rx_data; /* 0x0052 */
- u16 reserved_4[62]; /* 0x0054 */
- struct ihs_i2c i2c0; /* 0x00d0 */
-};
-#endif
-
-#ifdef CONFIG_STRIDER_CON
-struct ihs_fpga {
- u16 reflection_low; /* 0x0000 */
- u16 versions; /* 0x0002 */
- u16 fpga_version; /* 0x0004 */
- u16 fpga_features; /* 0x0006 */
- u16 reserved_0[1]; /* 0x0008 */
- u16 top_interrupt; /* 0x000a */
- u16 reserved_1[4]; /* 0x000c */
- struct ihs_gpio gpio; /* 0x0014 */
- u16 mpc3w_control; /* 0x001a */
- u16 reserved_2[2]; /* 0x001c */
- struct ihs_io_ep ep; /* 0x0020 */
- u16 reserved_3[9]; /* 0x002e */
- struct ihs_i2c i2c0; /* 0x0040 */
- u16 reserved_4[10]; /* 0x004c */
- u16 mc_int; /* 0x0060 */
- u16 mc_int_en; /* 0x0062 */
- u16 mc_status; /* 0x0064 */
- u16 mc_control; /* 0x0066 */
- u16 mc_tx_data; /* 0x0068 */
- u16 mc_tx_address; /* 0x006a */
- u16 mc_tx_cmd; /* 0x006c */
- u16 mc_res; /* 0x006e */
- u16 mc_rx_cmd_status; /* 0x0070 */
- u16 mc_rx_data; /* 0x0072 */
- u16 reserved_5[70]; /* 0x0074 */
- struct ihs_osd osd0; /* 0x0100 */
- u16 reserved_6[889]; /* 0x010e */
- u16 videomem0[2048]; /* 0x0800 */
-};
-#endif
-
#endif
projects / u-boot.git / commitdiff