This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
bool "CAM ENC 4xx board"
select SUPPORT_SPL
-config TARGET_HAWKBOARD
- bool "Hawkboard"
- select SUPPORT_SPL
-
config TARGET_DAVINCI_DM355EVM
bool "DM355 EVM board"
default "da850evm"
endif
-
-if TARGET_HAWKBOARD
-
-config SYS_BOARD
- default "da8xxevm"
-
-config SYS_VENDOR
- default "davinci"
-
-config SYS_CONFIG_NAME
- default "hawkboard"
-
-endif
F: configs/da850_am18xxevm_defconfig
F: configs/da850evm_defconfig
F: configs/da850evm_direct_nor_defconfig
-
-HAWKBOARD BOARD
-M: Syed Mohammed Khasim <sm.khasim@gmail.com>
-M: Sughosh Ganu <urwithsughosh@gmail.com>
-S: Maintained
-F: include/configs/hawkboard.h
-F: configs/hawkboard_defconfig
-F: configs/hawkboard_uart_defconfig
obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += da830evm.o
obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += da850evm.o
-obj-$(CONFIG_MACH_DAVINCI_HAWK) += hawkboard.o
+++ /dev/null
-Summary
-=======
-The README is for the boot procedure used for TI's OMAP-L138 based
-hawkboard. The hawkboard comes with a 128MiB Nand flash and a 128MiB
-DDR SDRAM along with a host of other controllers.
-
-The hawkboard is booted in three stages. The initial bootloader which
-executes upon reset is the Rom Boot Loader(RBL) which sits in the
-internal ROM of the omap. The RBL initialises the memory and the nand
-controller, and copies the image stored at a predefined location(block
-1) of the nand flash. The image loaded by the RBL to the memory is the
-AIS signed spl image. This, in turns copies the u-boot binary from the
-nand flash to the memory and jumps to the u-boot entry point.
-
-AIS is an image format defined by TI for the images that are to be
-loaded to memory by the RBL. The image is divided into a series of
-sections and the image's entry point is specified. Each section comes
-with meta data like the target address the section is to be copied to
-and the size of the section, which is used by the RBL to load the
-image. At the end of the image the RBL jumps to the image entry
-point.
-
-The secondary stage bootloader(spl) which is loaded by the RBL then
-loads the u-boot from a predefined location in the nand to the memory
-and jumps to the u-boot entry point.
-
-The reason a secondary stage bootloader is used is because the ECC
-layout expected by the RBL is not the same as that used by
-u-boot/linux. This also implies that for flashing the spl image,we
-need to use the u-boot which uses the ECC layout expected by the
-RBL[1]. Booting u-boot over UART(UART boot) is explained here[2].
-
-
-Compilation
-===========
-Three images might be needed
-
-* spl - This is the secondary bootloader which boots the u-boot
- binary.
-
-* u-boot binary - This is the image flashed to the nand and copied to
- the memory by the spl.
-
- Both the images get compiled with hawkboard_config, with the TOPDIR
- containing the u-boot images, and the spl image under the spl
- directory.
-
- The spl image needs to be processed with the AISGen tool for
- generating the AIS signed image to be flashed. Steps for generating
- the AIS image are explained here[3].
-
-* u-boot for uart boot - This is same as the u-boot binary generated
- above, with the sole difference of the CONFIG_SYS_TEXT_BASE being
- 0xc1080000, as expected by the RBL.
-
- hawkboard_uart_config
-
-
-Flashing the images to Nand
-===========================
-The spl AIS image needs to be flashed to the block 1 of the Nand
-flash, as that is the location the RBL expects the image[4]. For
-flashing the spl, boot over the u-boot specified in [1], and flash the
-image
-
-=> tftpboot 0xc0700000 <nand_spl_ais.bin>
-=> nand erase 0x20000 0x20000
-=> nand write.e 0xc0700000 0x20000 <nand_spl_size>
-
-The u-boot binary is flashed at location 0xe0000(block 6) of the nand
-flash. The spl loader expects the u-boot at this location. For
-flashing the u-boot binary
-
-=> tftpboot 0xc0700000 u-boot.bin
-=> nand erase 0xe0000 0x40000
-=> nand write.e 0xc0700000 0xe0000 <u-boot-size>
-
-
-Links
-=====
-
-[1]
- http://code.google.com/p/hawkboard/downloads/detail?name=u-boot_uart_ais_v1.bin
-
-[2]
- http://elinux.org/Hawkboard#Booting_u-boot_over_UART
-
-[3]
- http://elinux.org/Hawkboard#Signing_u-boot_for_UART_boot
-
-[4]
- http://processors.wiki.ti.com/index.php/RBL_UBL_and_host_program#RBL_booting_from_NAND_and_ECC.2FBad_blocks
+++ /dev/null
-# PLL0CFG0 PLL0CFG1
-PLL0 0x00180001 0x00000205
-# PLL1CFG0 PLL1CFG1 DRPYC1R SDCR SDTIMR1 SDTIMR2 SDRCR CLK2XSRC
-DDR2 0x15010001 0x00000002 0x00000043 0x00134632 0x26492a09 0x7d13c722 0x00000249 0x00000000
+++ /dev/null
-/*
- * Modified for Hawkboard - Syed Mohammed Khasim <khasim@beagleboard.org>
- *
- * Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc. <nsekhar@ti.com>
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- * Copyright (C) 2004 Texas Instruments.
- * Copyright (C) 2012 Sughosh Ganu <urwithsughosh@gmail.com>.
- *
- * ----------------------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- * ----------------------------------------------------------------------------
- */
-
-#include <common.h>
-#include <asm/errno.h>
-#include <asm/arch/hardware.h>
-#include <asm/io.h>
-#include <asm/arch/davinci_misc.h>
-#include <asm/arch/pinmux_defs.h>
-#include <asm/arch/da8xx-usb.h>
-#include <ns16550.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-const struct pinmux_resource pinmuxes[] = {
- PINMUX_ITEM(emac_pins_mii),
- PINMUX_ITEM(emac_pins_mdio),
- PINMUX_ITEM(emifa_pins_cs3),
- PINMUX_ITEM(emifa_pins_cs4),
- PINMUX_ITEM(emifa_pins_nand),
- PINMUX_ITEM(uart2_pins_txrx),
- PINMUX_ITEM(uart2_pins_rtscts),
-};
-
-const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
-
-const struct lpsc_resource lpsc[] = {
- { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
- { DAVINCI_LPSC_SPI1 }, /* Serial Flash */
- { DAVINCI_LPSC_EMAC }, /* image download */
- { DAVINCI_LPSC_UART2 }, /* console */
- { DAVINCI_LPSC_GPIO },
-};
-
-const int lpsc_size = ARRAY_SIZE(lpsc);
-
-int board_init(void)
-{
- /* arch number of the board */
- gd->bd->bi_arch_number = MACH_TYPE_OMAPL138_HAWKBOARD;
-
- /* address of boot parameters */
- gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
- return 0;
-}
-
-int board_early_init_f(void)
-{
- /*
- * Kick Registers need to be set to allow access to Pin Mux registers
- */
- writel(DV_SYSCFG_KICK0_UNLOCK, &davinci_syscfg_regs->kick0);
- writel(DV_SYSCFG_KICK1_UNLOCK, &davinci_syscfg_regs->kick1);
-
- /* set cfgchip3 to select mii */
- writel(readl(&davinci_syscfg_regs->cfgchip3) &
- ~(1 << 8), &davinci_syscfg_regs->cfgchip3);
-
- return 0;
-}
-
-int misc_init_r(void)
-{
- char buf[32];
-
- printf("ARM Clock : %s MHz\n",
- strmhz(buf, clk_get(DAVINCI_ARM_CLKID)));
-
- return 0;
-}
-
-int usb_phy_on(void)
-{
- u32 timeout;
- u32 cfgchip2;
-
- cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
-
- cfgchip2 &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN |
- CFGCHIP2_OTGMODE | CFGCHIP2_REFFREQ |
- CFGCHIP2_USB1PHYCLKMUX);
- cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN | CFGCHIP2_PHY_PLLON |
- CFGCHIP2_REFFREQ_24MHZ | CFGCHIP2_USB2PHYCLKMUX |
- CFGCHIP2_USB1SUSPENDM;
-
- writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);
-
- /* wait until the usb phy pll locks */
- timeout = DA8XX_USB_OTG_TIMEOUT;
- while (timeout--)
- if (readl(&davinci_syscfg_regs->cfgchip2) & CFGCHIP2_PHYCLKGD)
- return 1;
-
- /* USB phy was not turned on */
- return 0;
-}
-
-void usb_phy_off(void)
-{
- u32 cfgchip2;
-
- /*
- * Power down the on-chip PHY.
- */
- cfgchip2 = readl(&davinci_syscfg_regs->cfgchip2);
- cfgchip2 &= ~(CFGCHIP2_PHY_PLLON | CFGCHIP2_USB1SUSPENDM);
- cfgchip2 |= CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN | CFGCHIP2_RESET;
- writel(cfgchip2, &davinci_syscfg_regs->cfgchip2);
-}
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
- . = 0xc1080000;
-
- . = ALIGN(4);
- .text :
- {
- *(.vectors)
- arch/arm/cpu/arm926ejs/start.o (.text*)
- arch/arm/cpu/arm926ejs/built-in.o (.text*)
- drivers/mtd/nand/built-in.o (.text*)
-
- *(.text*)
- }
-
- . = ALIGN(4);
- .rodata : { *(.rodata*) }
-
- . = ALIGN(4);
- .data : {
- *(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
- }
-
- . = ALIGN(4);
- __image_copy_end = .;
- __rel_dyn_start = .;
- __rel_dyn_end = .;
-
- __got_start = .;
- . = ALIGN(4);
- .got : { *(.got) }
-
- __got_end = .;
-
- .bss :
- {
- . = ALIGN(4);
- __bss_start = .;
- *(.bss*)
- . = ALIGN(4);
- __bss_end = .;
- }
-
- .end :
- {
- *(.__end)
- }
-}
+++ /dev/null
-CONFIG_SPL=y
-+S:CONFIG_ARM=y
-+S:CONFIG_ARCH_DAVINCI=y
-+S:CONFIG_TARGET_HAWKBOARD=y
+++ /dev/null
-CONFIG_SPL=y
-CONFIG_SYS_EXTRA_OPTIONS="UART_U_BOOT"
-+S:CONFIG_ARM=y
-+S:CONFIG_ARCH_DAVINCI=y
-+S:CONFIG_TARGET_HAWKBOARD=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+hawkboard arm arm926ejs - - Syed Mohammed Khasim <sm.khasim@gmail.com>:Sughosh Ganu <urwithsughosh@gmail.com>
tnetv107x arm arm1176 - - Chan-Taek Park <c-park@ti.com>
a320evb arm arm920t - - Po-Yu Chuang <ratbert@faraday-tech.com>
cm4008 arm arm920t - - Greg Ungerer <greg.ungerer@opengear.com>
+++ /dev/null
-/*
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
- *
- * Based on davinci_dvevm.h. Original Copyrights follow:
- *
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * Board
- */
-#define CONFIG_SYS_USE_NAND 1
-
-/*
- * SoC Configuration
- */
-#define CONFIG_MACH_DAVINCI_HAWK
-#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */
-#define CONFIG_SOC_DA850 /* TI DA850 SoC */
-#define CONFIG_SYS_EXCEPTION_VECTORS_HIGH
-#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
-#define CONFIG_SYS_OSCIN_FREQ 24000000
-#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
-#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_AIS_CONFIG_FILE "board/$(BOARDDIR)/hawkboard-ais-nand.cfg"
-
-#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
- DAVINCI_SYSCFG_SUSPSRC_EMAC | \
- DAVINCI_SYSCFG_SUSPSRC_I2C | \
- DAVINCI_SYSCFG_SUSPSRC_SPI1 | \
- DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
- DAVINCI_SYSCFG_SUSPSRC_UART2)
-
-#if defined(CONFIG_UART_U_BOOT)
-#define CONFIG_SYS_TEXT_BASE 0xc1080000
-#elif !defined(CONFIG_SPL_BUILD)
-#define CONFIG_SYS_TEXT_BASE 0xc1180000
-#endif
-
-/* Spl */
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_LIBGENERIC_SUPPORT /* for udelay and __div64_32 for NAND */
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-hawk.lds"
-#define CONFIG_SPL_TEXT_BASE 0xc1080000
-#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
-
-/*
- * Memory Info
- */
-#define CONFIG_SYS_MALLOC_LEN (1*1024*1024) /* malloc() len */
-#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE
-#define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */
-#define CONFIG_SYS_SDRAM_BASE 0xc0000000
-#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 -\
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_MONITOR_LEN 0x60000
-
-/* memtest start addr */
-#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1)
-
-/* memtest will be run on 16MB */
-#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024)
-
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-
-/*
- * Serial Driver info
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4
-#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE
-#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/*
- * Network & Ethernet Configuration
- */
-#define CONFIG_DRIVER_TI_EMAC
-#define CONFIG_MII
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-
-/*
- * Nand Flash
- */
-#ifdef CONFIG_SYS_USE_NAND
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE (128 << 10)
-#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
-#define CONFIG_CLE_MASK 0x10
-#define CONFIG_ALE_MASK 0x8
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
-#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST /* SPL nand driver configuration */
-#define CFG_DAVINCI_STD_NAND_LAYOUT
-#define CONFIG_SYS_NAND_CS 3
-#define CONFIG_SYS_NAND_PAGE_2K
-/* Max number of NAND devices */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE_LIST { 0x62000000, }
-/* Block 0--not used by bootcode */
-#define CONFIG_ENV_OFFSET 0x0
-
-#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10)
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0xe0000
-#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1180000
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
-#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
- CONFIG_SYS_NAND_U_BOOT_SIZE - \
- CONFIG_SYS_MALLOC_LEN - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_NAND_ECCPOS { \
- 24, 25, 26, 27, 28, \
- 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
- 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
- 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
- 59, 60, 61, 62, 63 }
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
-#define CONFIG_SYS_NAND_ECCSIZE 512
-#define CONFIG_SYS_NAND_ECCBYTES 10
-#define CONFIG_SYS_NAND_OOBSIZE 64
-
-#endif /* CONFIG_SYS_USE_NAND */
-
-/* USB Configs */
-#define CONFIG_SYS_USB_OHCI_CPU_INIT
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_USB_OHCI_DA8XX
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x01E25000
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "hawkboard"
-
-/*
- * U-Boot general configuration
- */
-#define CONFIG_MISC_INIT_R
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_PROMPT "hawkboard > " /* Command Prompt */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-
-/*
- * Linux Information
- */
-#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100)
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS \
- "mem=128M console=ttyS2,115200n8 root=/dev/ram0 rw initrd=0xc1180000,"\
- "4M ip=static"
-#define CONFIG_BOOTDELAY 3
-
-/*
- * U-Boot commands
- */
-#include <config_cmd_default.h>
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_EXT2
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-#ifdef CONFIG_SYS_USE_NAND
-#undef CONFIG_CMD_FLASH
-#undef CONFIG_CMD_IMLS
-#define CONFIG_CMD_NAND
-#endif
-
-#ifndef CONFIG_DRIVER_TI_EMAC
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_DHCP
-#undef CONFIG_CMD_MII
-#undef CONFIG_CMD_PING
-#endif
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff