This board is old enough and has no maintainer.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = rbc823.o flash.o kbd.o
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-/*
- * Functions
- */
-static ulong flash_get_size(vu_long *addr, flash_info_t *info);
-static int write_word(flash_info_t *info, ulong dest, ulong data);
-static void flash_get_offsets(ulong base, flash_info_t *info);
-
-unsigned long flash_init(void)
-{
- unsigned long size_b0;
- int i;
-
- /* Init: no FLASHes known */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i)
- flash_info[i].flash_id = FLASH_UNKNOWN;
-
- /* Detect size */
- size_b0 = flash_get_size((vu_long *)CONFIG_SYS_FLASH_BASE,
- &flash_info[0]);
-
- /* Setup offsets */
- flash_get_offsets(CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* Monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[0]);
-#endif
-
- flash_info[0].size = size_b0;
-
- return size_b0;
-}
-
-/*-----------------------------------------------------------------------
- * Fix this to support variable sector sizes
-*/
-static void flash_get_offsets(ulong base, flash_info_t *info)
-{
- int i;
-
- /* set up sector start address table */
- if ((info->flash_id & FLASH_TYPEMASK) == FLASH_AM040) {
- /* set sector offsets for bottom boot block type */
- for (i = 0; i < info->sector_count; i++)
- info->start[i] = base + (i * 0x00010000);
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info(flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- puts("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD:
- printf("AMD ");
- break;
- case FLASH_MAN_FUJ:
- printf("FUJITSU ");
- break;
- case FLASH_MAN_BM:
- printf("BRIGHT MICRO ");
- break;
- default:
- printf("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM040:
- printf("29F040 or 29LV040 (4 Mbit, uniform sectors)\n");
- break;
- case FLASH_AM400B:
- printf("AM29LV400B (4 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM400T:
- printf("AM29LV400T (4 Mbit, top boot sector)\n");
- break;
- case FLASH_AM800B:
- printf("AM29LV800B (8 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM800T:
- printf("AM29LV800T (8 Mbit, top boot sector)\n");
- break;
- case FLASH_AM160B:
- printf("AM29LV160B (16 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM160T:
- printf("AM29LV160T (16 Mbit, top boot sector)\n");
- break;
- case FLASH_AM320B:
- printf("AM29LV320B (32 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM320T:
- printf("AM29LV320T (32 Mbit, top boot sector)\n");
- break;
- default:
- printf("Unknown Chip Type\n");
- break;
- }
-
- if (info->size >> 20) {
- printf(" Size: %ld MB in %d Sectors\n",
- info->size >> 20,
- info->sector_count);
- } else {
- printf(" Size: %ld KB in %d Sectors\n",
- info->size >> 10,
- info->sector_count);
- }
-
- puts(" Sector Start Addresses:");
-
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- puts("\n ");
-
- printf(" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " ");
- }
-
- putc('\n');
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size(vu_long *addr, flash_info_t *info)
-{
- short i;
- volatile unsigned char *caddr;
- char value;
-
- caddr = (volatile unsigned char *)addr ;
-
- /* Write auto select command: read Manufacturer ID */
-
- debug("Base address is: %8p\n", caddr);
-
- caddr[0x0555] = 0xAA;
- caddr[0x02AA] = 0x55;
- caddr[0x0555] = 0x90;
-
- value = caddr[0];
-
- debug("Manufact ID: %02x\n", value);
-
- switch (value) {
- case 0x01: /*AMD_MANUFACT*/
- info->flash_id = FLASH_MAN_AMD;
- break;
-
- case 0x04: /*FUJ_MANUFACT*/
- info->flash_id = FLASH_MAN_FUJ;
- break;
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- break;
- }
-
- value = caddr[1]; /* device ID */
-
- debug("Device ID: %02x\n", value);
-
- switch (value) {
- case AMD_ID_LV040B:
- info->flash_id += FLASH_AM040;
- info->sector_count = 8;
- info->size = 0x00080000;
- break; /* => 512Kb */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- return 0; /* => no or unknown flash */
- }
-
- flash_get_offsets((ulong)addr, &flash_info[0]);
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /*
- * read sector protection at sector address,
- * (A7 .. A0) = 0x02
- * D0 = 1 if protected
- */
- caddr = (volatile unsigned char *)(info->start[i]);
- info->protect[i] = caddr[2] & 1;
- }
-
- /*
- * Prevent writes to uninitialized FLASH.
- */
- if (info->flash_id != FLASH_UNKNOWN) {
- caddr = (volatile unsigned char *)info->start[0];
- *caddr = 0xF0; /* reset bank */
- }
-
- return info->size;
-}
-
-
-int flash_erase(flash_info_t *info, int s_first, int s_last)
-{
- volatile unsigned char *addr =
- (volatile unsigned char *)(info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN)
- printf("- missing\n");
- else
- printf("- no sectors to erase\n");
-
- return 1;
- }
-
- if ((info->flash_id == FLASH_UNKNOWN) ||
- (info->flash_id > FLASH_AMD_COMP)) {
- printf("Can't erase unknown flash type - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect])
- prot++;
- }
-
- if (prot) {
- printf("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
- addr[0x0555] = 0x80;
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (volatile unsigned char *)(info->start[sect]);
- addr[0] = 0x30;
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay(1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer(0);
- last = start;
- addr = (volatile unsigned char *)(info->start[l_sect]);
-
- while ((addr[0] & 0xFF) != 0xFF) {
- now = get_timer(start);
- if (now > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc('.');
- last = now;
- }
- }
-
-DONE:
- /* reset to read mode */
- addr = (volatile unsigned char *)info->start[0];
-
- addr[0] = 0xF0; /* reset bank */
-
- printf(" done\n");
- return 0;
-}
-
-/*
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff(flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- l = addr - wp;
-
- if (l != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp)
- data = (data << 8) | (*(uchar *)cp);
-
- for (; i < 4 && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
-
- for (; cnt == 0 && i < 4; ++i, ++cp)
- data = (data << 8) | (*(uchar *)cp);
-
- rc = write_word(info, wp, data);
-
- if (rc != 0)
- return rc;
-
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i = 0; i < 4; ++i)
- data = (data << 8) | *src++;
-
- rc = write_word(info, wp, data);
-
- if (rc != 0)
- return rc;
-
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0)
- return 0;
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < 4; ++i, ++cp)
- data = (data << 8) | (*(uchar *)cp);
-
- return write_word(info, wp, data);
-}
-
-/*
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word(flash_info_t *info, ulong dest, ulong data)
-{
- volatile unsigned char *cdest, *cdata;
- volatile unsigned char *addr =
- (volatile unsigned char *)(info->start[0]);
- ulong start;
- int flag, count = 4 ;
-
- cdest = (volatile unsigned char *)dest ;
- cdata = (volatile unsigned char *)&data ;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*((vu_long *)dest)&data) != data)
- return 2;
-
- while (count--) {
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0xAA;
- addr[0x02AA] = 0x55;
- addr[0x0555] = 0xA0;
-
- *cdest = *cdata;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer(0);
- while ((*cdest ^ *cdata) & 0x80) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT)
- return 1;
- }
-
- cdata++ ;
- cdest++ ;
- }
- return 0;
-}
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* Modified by Udi Finkelstein
- *
- * This file includes communication routines for SMC1 that can run even if
- * SMC2 have already been initialized.
- */
-
-#include <common.h>
-#include <watchdog.h>
-#include <commproc.h>
-#include <stdio_dev.h>
-#include <lcd.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define SMC_INDEX 0
-#define PROFF_SMC PROFF_SMC1
-#define CPM_CR_CH_SMC CPM_CR_CH_SMC1
-
-#define RBC823_KBD_BAUDRATE 38400
-#define CPM_KEYBOARD_BASE 0x1000
-/*
- * Minimal serial functions needed to use one of the SMC ports
- * as serial console interface.
- */
-
-void smc1_setbrg (void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = &(im->im_cpm);
-
- /* Set up the baud rate generator.
- * See 8xx_io/commproc.c for details.
- *
- * Wire BRG2 to SMC1, BRG1 to SMC2
- */
-
- cp->cp_simode = 0x00001000;
-
- cp->cp_brgc2 =
- (((gd->cpu_clk / 16 / RBC823_KBD_BAUDRATE)-1) << 1) | CPM_BRG_EN;
-}
-
-int smc1_init (void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile smc_t *sp;
- volatile smc_uart_t *up;
- volatile cbd_t *tbdf, *rbdf;
- volatile cpm8xx_t *cp = &(im->im_cpm);
- uint dpaddr;
-
- /* initialize pointers to SMC */
-
- sp = (smc_t *) &(cp->cp_smc[SMC_INDEX]);
- up = (smc_uart_t *) &cp->cp_dparam[PROFF_SMC];
-
- /* Disable transmitter/receiver.
- */
- sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
-
- /* Enable SDMA.
- */
- im->im_siu_conf.sc_sdcr = 1;
-
- /* clear error conditions */
-#ifdef CONFIG_SYS_SDSR
- im->im_sdma.sdma_sdsr = CONFIG_SYS_SDSR;
-#else
- im->im_sdma.sdma_sdsr = 0x83;
-#endif
-
- /* clear SDMA interrupt mask */
-#ifdef CONFIG_SYS_SDMR
- im->im_sdma.sdma_sdmr = CONFIG_SYS_SDMR;
-#else
- im->im_sdma.sdma_sdmr = 0x00;
-#endif
-
- /* Use Port B for SMC1 instead of other functions.
- */
- cp->cp_pbpar |= 0x000000c0;
- cp->cp_pbdir &= ~0x000000c0;
- cp->cp_pbodr &= ~0x000000c0;
-
- /* Set the physical address of the host memory buffers in
- * the buffer descriptors.
- */
-
-#ifdef CONFIG_SYS_ALLOC_DPRAM
- dpaddr = dpram_alloc_align (sizeof(cbd_t)*2 + 2, 8) ;
-#else
- dpaddr = CPM_KEYBOARD_BASE ;
-#endif
-
- /* Allocate space for two buffer descriptors in the DP ram.
- * For now, this address seems OK, but it may have to
- * change with newer versions of the firmware.
- * damm: allocating space after the two buffers for rx/tx data
- */
-
- rbdf = (cbd_t *)&cp->cp_dpmem[dpaddr];
- rbdf->cbd_bufaddr = (uint) (rbdf+2);
- rbdf->cbd_sc = 0;
- tbdf = rbdf + 1;
- tbdf->cbd_bufaddr = ((uint) (rbdf+2)) + 1;
- tbdf->cbd_sc = 0;
-
- /* Set up the uart parameters in the parameter ram.
- */
- up->smc_rbase = dpaddr;
- up->smc_tbase = dpaddr+sizeof(cbd_t);
- up->smc_rfcr = SMC_EB;
- up->smc_tfcr = SMC_EB;
-
- /* Set UART mode, 8 bit, no parity, one stop.
- * Enable receive and transmit.
- */
- sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
-
- /* Mask all interrupts and remove anything pending.
- */
- sp->smc_smcm = 0;
- sp->smc_smce = 0xff;
-
- /* Set up the baud rate generator.
- */
- smc1_setbrg ();
-
- /* Make the first buffer the only buffer.
- */
- tbdf->cbd_sc |= BD_SC_WRAP;
- rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
-
- /* Single character receive.
- */
- up->smc_mrblr = 1;
- up->smc_maxidl = 0;
-
- /* Initialize Tx/Rx parameters.
- */
-
- while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
- ;
-
- cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_SMC, CPM_CR_INIT_TRX) | CPM_CR_FLG;
-
- while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
- ;
-
- /* Enable transmitter/receiver.
- */
- sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
-
- return (0);
-}
-
-void smc1_putc(const char c)
-{
- volatile cbd_t *tbdf;
- volatile char *buf;
- volatile smc_uart_t *up;
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
-
- up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC];
-
- tbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_tbase];
-
- /* Wait for last character to go.
- */
-
- buf = (char *)tbdf->cbd_bufaddr;
-
- *buf = c;
- tbdf->cbd_datlen = 1;
- tbdf->cbd_sc |= BD_SC_READY;
- __asm__("eieio");
-
- while (tbdf->cbd_sc & BD_SC_READY) {
- WATCHDOG_RESET ();
- __asm__("eieio");
- }
-}
-
-int smc1_getc(void)
-{
- volatile cbd_t *rbdf;
- volatile unsigned char *buf;
- volatile smc_uart_t *up;
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
- unsigned char c;
-
- up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC];
-
- rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
-
- /* Wait for character to show up.
- */
- buf = (unsigned char *)rbdf->cbd_bufaddr;
-
- while (rbdf->cbd_sc & BD_SC_EMPTY)
- WATCHDOG_RESET ();
-
- c = *buf;
- rbdf->cbd_sc |= BD_SC_EMPTY;
-
- return(c);
-}
-
-int smc1_tstc(void)
-{
- volatile cbd_t *rbdf;
- volatile smc_uart_t *up;
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cpmp = &(im->im_cpm);
-
- up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC];
-
- rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
-
- return(!(rbdf->cbd_sc & BD_SC_EMPTY));
-}
-
-/* search for keyboard and register it if found */
-int drv_keyboard_init(void)
-{
- int error = 0;
- struct stdio_dev kbd_dev;
-
- if (0) {
- /* register the keyboard */
- memset (&kbd_dev, 0, sizeof(struct stdio_dev));
- strcpy(kbd_dev.name, "kbd");
- kbd_dev.flags = DEV_FLAGS_INPUT | DEV_FLAGS_SYSTEM;
- kbd_dev.putc = NULL;
- kbd_dev.puts = NULL;
- kbd_dev.getc = smc1_getc;
- kbd_dev.tstc = smc1_tstc;
- error = stdio_register (&kbd_dev);
- } else {
- lcd_is_enabled = 0;
- lcd_disable();
- }
- return error;
-}
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include "mpc8xx.h"
-#include <linux/mtd/doc2000.h>
-
-extern int kbd_init(void);
-extern int drv_kbd_init(void);
-
-/* ------------------------------------------------------------------------- */
-
-static long int dram_size (long int, long int *, long int);
-
-/* ------------------------------------------------------------------------- */
-
-#define _NOT_USED_ 0xFFFFFFFF
-
-const uint sdram_table[] =
-{
- /*
- * Single Read. (Offset 0 in UPMA RAM)
- */
- 0x1F07FC04, 0xEEAEFC04, 0x11ADFC04, 0xEFBBBC00,
- 0x1FF77C47, /* last */
- /*
- * SDRAM Initialization (offset 5 in UPMA RAM)
- *
- * This is no UPM entry point. The following definition uses
- * the remaining space to establish an initialization
- * sequence, which is executed by a RUN command.
- *
- */
- 0x1FF77C34, 0xEFEABC34, 0x1FB57C35, /* last */
- /*
- * Burst Read. (Offset 8 in UPMA RAM)
- */
- 0x1F07FC04, 0xEEAEFC04, 0x10ADFC04, 0xF0AFFC00,
- 0xF0AFFC00, 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Single Write. (Offset 18 in UPMA RAM)
- */
- 0x1F27FC04, 0xEEAEBC00, 0x01B93C04, 0x1FF77C47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Burst Write. (Offset 20 in UPMA RAM)
- */
- 0x1F07FC04, 0xEEAEBC00, 0x10AD7C00, 0xF0AFFC00,
- 0xF0AFFC00, 0xE1BBBC04, 0x1FF77C47, /* last */
- _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Refresh (Offset 30 in UPMA RAM)
- */
- 0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC84, 0xFFFFFC07, /* last */
- _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Exception. (Offset 3c in UPMA RAM)
- */
- 0x1FF7FC07, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_,
-};
-
-const uint static_table[] =
-{
- /*
- * Single Read. (Offset 0 in UPMA RAM)
- */
- 0x0FFFFC04, 0x0FF3FC04, 0x0FF3CC04, 0x0FF3CC04,
- 0x0FF3EC04, 0x0FF3CC00, 0x0FF7FC04, 0x3FFFFC04,
- 0xFFFFFC04, 0xFFFFFC05, /* last */
- _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Single Write. (Offset 18 in UPMA RAM)
- */
- 0x0FFFFC04, 0x00FFFC04, 0x00FFFC04, 0x00FFFC04,
- 0x01FFFC00, 0x3FFFFC04, 0xFFFFFC04, 0xFFFFFC05, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
-};
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check Board Identity:
- *
- * Test TQ ID string (TQM8xx...)
- * If present, check for "L" type (no second DRAM bank),
- * otherwise "L" type is assumed as default.
- *
- * Return 1 for "L" type, 0 else.
- */
-
-int checkboard (void)
-{
- char buf[64];
- int i = getenv_f("serial#", buf, sizeof(buf));
-
- if (i < 0 || strncmp(buf, "TQM8", 4)) {
- printf ("### No HW ID - assuming RBC823\n");
- return (0);
- }
-
- puts(buf);
- putc('\n');
-
- return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- long int size_b0, size8, size9;
-
- upmconfig (UPMA, (uint *) sdram_table,
- sizeof (sdram_table) / sizeof (uint));
-
- /*
- * 1 Bank of 64Mbit x 2 devices
- */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_1BK_4K;
- memctl->memc_mar = 0x00000088;
-
- /*
- * Map controller SDRAM bank 0
- */
- memctl->memc_or4 = CONFIG_SYS_OR4_PRELIM;
- memctl->memc_br4 = CONFIG_SYS_BR4_PRELIM;
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
- udelay (200);
-
- /*
- * Perform SDRAM initializsation sequence
- */
- memctl->memc_mcr = 0x80008105; /* SDRAM bank 0 */
- udelay (1);
- memctl->memc_mamr = (CONFIG_SYS_MAMR_8COL & ~(MAMR_TLFA_MSK)) | MAMR_TLFA_8X;
- udelay (200);
- memctl->memc_mcr = 0x80008130; /* SDRAM bank 0 - execute twice */
- udelay (1);
- memctl->memc_mamr = (CONFIG_SYS_MAMR_8COL & ~(MAMR_TLFA_MSK)) | MAMR_TLFA_4X;
- udelay (200);
-
- memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
- udelay (1000);
-
- /*
- * Preliminary prescaler for refresh (depends on number of
- * banks): This value is selected for four cycles every 62.4 us
- * with two SDRAM banks or four cycles every 31.2 us with one
- * bank. It will be adjusted after memory sizing.
- */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K; /* 16: but should be: CONFIG_SYS_MPTPR_1BK_4K */
-
- /*
- * Check Bank 0 Memory Size for re-configuration
- *
- * try 8 column mode
- */
- size8 = dram_size (CONFIG_SYS_MAMR_8COL, (long *) SDRAM_BASE4_PRELIM,
- SDRAM_MAX_SIZE);
- udelay (1000);
-
- /*
- * try 9 column mode
- */
- size9 = dram_size (CONFIG_SYS_MAMR_9COL, (long *) SDRAM_BASE4_PRELIM,
- SDRAM_MAX_SIZE);
-
- if (size8 < size9) { /* leave configuration at 9 columns */
- size_b0 = size9;
-/* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
- } else { /* back to 8 columns */
- size_b0 = size8;
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
- udelay (500);
-/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
- }
-
- udelay (1000);
-
- /*
- * Adjust refresh rate depending on SDRAM type, both banks
- * For types > 128 MBit leave it at the current (fast) rate
- */
- if ((size_b0 < 0x02000000)) {
- /* reduce to 15.6 us (62.4 us / quad) */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
- udelay (1000);
- }
-
- /* SDRAM Bank 0 is bigger - map first */
-
- memctl->memc_or4 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
- memctl->memc_br4 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
-
- udelay (10000);
-
- return (size_b0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check memory range for valid RAM. A simple memory test determines
- * the actually available RAM size between addresses `base' and
- * `base + maxsize'. Some (not all) hardware errors are detected:
- * - short between address lines
- * - short between data lines
- */
-
-static long int dram_size (long int mamr_value, long int *base,
- long int maxsize)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- memctl->memc_mamr = mamr_value;
-
- return (get_ram_size (base, maxsize));
-}
-
-#ifdef CONFIG_CMD_DOC
-void doc_init (void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- upmconfig (UPMB, (uint *) static_table,
- sizeof (static_table) / sizeof (uint));
- memctl->memc_mbmr = MAMR_DSA_1_CYCL;
-
- doc_probe (FLASH_BASE1_PRELIM);
-}
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- lib/built-in.o (.text*)
- net/built-in.o (.text*)
- arch/powerpc/cpu/mpc8xx/built-in.o (.text*)
- arch/powerpc/lib/built-in.o (.text*)
-
- . = env_offset;
- common/env_embedded.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
Active powerpc mpc8xx - - netvia NETVIA NETVIA:NETVIA_VERSION=1 Pantelis Antoniou <panto@intracom.gr>
Active powerpc mpc8xx - - netvia NETVIA_V2 NETVIA:NETVIA_VERSION=2 Pantelis Antoniou <panto@intracom.gr>
Active powerpc mpc8xx - - r360mpi R360MPI - Wolfgang Denk <wd@denx.de>
-Active powerpc mpc8xx - - rbc823 RBC823 - -
Active powerpc mpc8xx - - RRvision RRvision_LCD RRvision:LCD,SHARP_LQ104V7DS01 Wolfgang Denk <wd@denx.de>
Active powerpc mpc8xx - - spd8xx SPD823TS - Wolfgang Denk <wd@denx.de>
Active powerpc mpc8xx - eltec mhpc MHPC - Frank Gottschling <fgottschling@eltec.de>
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+rbc823 powerpc mpc8xx - -
quantum powerpc mpc8xx - -
RPXlite_dw powerpc mpc8xx - -
qs850 powerpc mpc8xx - -
/* Initialize LCD controller bus priorities.
*/
-#ifdef CONFIG_RBC823
- immr->im_siu_conf.sc_sdcr = (immr->im_siu_conf.sc_sdcr & ~0x0f) | 1; /* RAID = 01, LAID = 00 */
-#else
immr->im_siu_conf.sc_sdcr &= ~0x0f; /* RAID = LAID = 0 */
/* set SHFT/CLOCK division factor 4
immr->im_clkrst.car_sccr &= ~0x1F;
immr->im_clkrst.car_sccr |= LCD_DF; /* was 8 */
-#endif /* CONFIG_RBC823 */
-
-#if defined(CONFIG_RBC823)
- /* Enable LCD on port D.
- */
- immr->im_ioport.iop_pddat &= 0x0300;
- immr->im_ioport.iop_pdpar |= 0x1CFF;
- immr->im_ioport.iop_pddir |= 0x1CFF;
-
- /* Configure LCD_ON, VEE_ON, CCFL_ON on port B.
- */
- immr->im_cpm.cp_pbdat &= ~0x00005001;
- immr->im_cpm.cp_pbpar &= ~0x00005001;
- immr->im_cpm.cp_pbdir |= 0x00005001;
-#elif !defined(CONFIG_EDT32F10)
+#if !defined(CONFIG_EDT32F10)
/* Enable LCD on port D.
*/
immr->im_ioport.iop_pdpar |= 0x1FFF;
volatile lcd823_t *lcdp = &immr->im_lcd;
/* Enable the LCD panel */
-#ifndef CONFIG_RBC823
immr->im_siu_conf.sc_sdcr |= (1 << (31 - 25)); /* LAM = 1 */
-#endif
lcdp->lcd_lccr |= LCCR_PON;
#ifdef CONFIG_V37
/* Turn on display backlight */
immr->im_cpm.cp_pbpar |= 0x00008000;
immr->im_cpm.cp_pbdir |= 0x00008000;
-#elif defined(CONFIG_RBC823)
- /* Turn on display backlight */
- immr->im_cpm.cp_pbdat |= 0x00004000;
#endif
#if defined(CONFIG_LWMON)
r360_i2c_lcd_write(0x40 | ((ctr>>8) & 0xF), ctr & 0xFF);
}
#endif /* CONFIG_R360MPI */
-#ifdef CONFIG_RBC823
- udelay(200000); /* wait 200ms */
- /* Turn VEE_ON first */
- immr->im_cpm.cp_pbdat |= 0x00000001;
- udelay(200000); /* wait 200ms */
- /* Now turn on LCD_ON */
- immr->im_cpm.cp_pbdat |= 0x00001000;
-#endif
#ifdef CONFIG_RRVISION
debug ("PC4->Output(1): enable LVDS\n");
debug ("PC5->Output(0): disable PAL clock\n");
#endif
}
-/*----------------------------------------------------------------------*/
-
-#if defined (CONFIG_RBC823)
-void lcd_disable (void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile lcd823_t *lcdp = &immr->im_lcd;
-
-#if defined(CONFIG_LWMON)
- { uchar c = pic_read (0x60);
- c &= ~0x07; /* Power off CCFL, Disable CCFL, Chip Disable LCD */
- pic_write (0x60, c);
- }
-#elif defined(CONFIG_R360MPI)
- {
- extern void r360_i2c_lcd_write (uchar data0, uchar data1);
-
- r360_i2c_lcd_write(0x10, 0x00);
- r360_i2c_lcd_write(0x20, 0x00);
- r360_i2c_lcd_write(0x30, 0x00);
- r360_i2c_lcd_write(0x40, 0x00);
- }
-#endif /* CONFIG_LWMON */
- /* Disable the LCD panel */
- lcdp->lcd_lccr &= ~LCCR_PON;
-#ifdef CONFIG_RBC823
- /* Turn off display backlight, VEE and LCD_ON */
- immr->im_cpm.cp_pbdat &= ~0x00005001;
-#else
- immr->im_siu_conf.sc_sdcr &= ~(1 << (31 - 25)); /* LAM = 0 */
-#endif /* CONFIG_RBC823 */
-}
-#endif /* NOT_USED_SO_FAR || CONFIG_RBC823 */
-
-
/************************************************************************/
#endif /* CONFIG_LCD */
/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/
#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
- defined(CONFIG_R360MPI) || defined(CONFIG_RBC823) || \
+ defined(CONFIG_R360MPI) || \
defined(CONFIG_RRVISION)|| defined(CONFIG_TQM823L) || \
defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) || \
+++ /dev/null
-/*
- * (C) Copyright 2000, 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * Modified by Udi Finkelstein udif@udif.com
- * For the RBC823 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
-#define CONFIG_RBC823 1 /* ...on a RBC823 module */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#if 0
-#define DEBUG 1
-#define CONFIG_LAST_STAGE_INIT
-#endif
-#define CONFIG_KEYBOARD 1 /* This board has a custom keybpard */
-#define CONFIG_LCD 1 /* use LCD controller ... */
-#define CONFIG_MPC8XX_LCD
-#define CONFIG_HITACHI_SP19X001_Z1A /* The LCD type we use */
-
-#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */
-#undef CONFIG_8xx_CONS_SMC1
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
-#if 1
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-#define CONFIG_8xx_GCLK_FREQ 48000000L
-
-#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
- "bootm"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#undef CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#undef CONFIG_RTC_MPC8xx /* don't use internal RTC of MPC8xx (no battery) */
-
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED 40000
-#define CONFIG_SYS_I2C_SLAVE 0xfe
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_WRITE_DELAY_MS 10
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_BMP
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_CDP
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_KGDB
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_PORTIO
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_SDRAM
-
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_XIMG
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x0100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFF000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFFF00000
-#if defined(DEBUG)
-#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 256 kB for Monitor */
-#else
-#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 192 kB for Monitor */
-#endif
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-/*
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-*/
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWRI | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC00 | SIUMCR_FRC)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- */
-
-/*
- * for 48 MHz, we use a 4 MHz clock * 12
- */
-#define CONFIG_SYS_PLPRCR \
- ( (12-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_LOLRE )
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_RTDIV | SCCR_RTSEL | SCCR_CRQEN | \
- SCCR_PRQEN | SCCR_EBDF00 | \
- SCCR_COM01 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD001 | \
- SCCR_DFALCD00)
-
-#ifdef NOT_USED
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_PCMCIA /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-#endif
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-/*#define CONFIG_SYS_DER 0x2002000F*/
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0xFFF00000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x04000000 /* D.O.C Millenium */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_PRELIM_OR_AM 0xFFF80000 /* OR addr mask */
-
-/* FLASH timing: ACS = 00, TRLX = 0, CSNT = 1, SCY = 7, EHTR = 1 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_BI | OR_SCY_7_CLK | OR_EHTR)
-
-#define CONFIG_SYS_OR_TIMING_MSYS (OR_ACS_DIV1 | OR_BI)
-
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V)
-
-#define CONFIG_SYS_OR1_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_MSYS)
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMB | \
- BR_PS_8 | BR_V)
-
-/*
- * BR4 and OR4 (SDRAM)
- *
- */
-#define SDRAM_BASE4_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/*
- * SDRAM timing:
- */
-#define CONFIG_SYS_OR_TIMING_SDRAM (OR_CSNT_SAM)
-
-#define CONFIG_SYS_OR4_PRELIM (~(SDRAM_MAX_SIZE-1) | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR4_PRELIM ((SDRAM_BASE4_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA 187 /* start with divider for 48 MHz */
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nor0"
-#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT ""
-#define MTDPARTS_DEFAULT ""
-*/
-
-#endif /* __CONFIG_H */
/* Video functions */
-#if defined(CONFIG_RBC823)
-void lcd_disable(void);
-#endif
-
void lcd_putc(const char c);
void lcd_puts(const char *s);
void lcd_printf(const char *fmt, ...);
# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-/***** RBC823 ********************************************************/
-#elif defined(CONFIG_RBC823)
-
-# define STATUS_LED_PAR im_ioport.iop_pcpar
-# define STATUS_LED_DIR im_ioport.iop_pcdir
-# undef STATUS_LED_ODR
-# define STATUS_LED_DAT im_ioport.iop_pcdat
-
-# define STATUS_LED_BIT 0x0002 /* LED 0 is on PC.14 */
-# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-# define STATUS_LED_STATE STATUS_LED_BLINKING
-# define STATUS_LED_BIT1 0x0004 /* LED 1 is on PC.13 */
-# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ)
-# define STATUS_LED_STATE1 STATUS_LED_OFF
-
-# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */
-
-# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
-
/***** NetPhone ********************************************************/
#elif defined(CONFIG_NETPHONE) || defined(CONFIG_NETTA2)
/* XXX empty just to avoid the error */
projects / u-boot.git / commitdiff