#include <linux/mtd/nand_ecc.h>
#include <linux/compiler.h>
#include <nand.h>
+#ifdef CONFIG_AM33XX
+#include <asm/arch/elm.h>
+#endif
static uint8_t cs;
static __maybe_unused struct nand_ecclayout hw_nand_oob =
}
}
+/*
+ * BCH8 support (needs ELM and thus AM33xx-only)
+ */
+#ifdef CONFIG_AM33XX
+struct nand_bch_priv {
+ uint8_t mode;
+ uint8_t type;
+ uint8_t nibbles;
+};
+
+/* bch types */
+#define ECC_BCH4 0
+#define ECC_BCH8 1
+#define ECC_BCH16 2
+
+/* BCH nibbles for diff bch levels */
+#define NAND_ECC_HW_BCH ((uint8_t)(NAND_ECC_HW_OOB_FIRST) + 1)
+#define ECC_BCH4_NIBBLES 13
+#define ECC_BCH8_NIBBLES 26
+#define ECC_BCH16_NIBBLES 52
+
+static struct nand_ecclayout hw_bch8_nand_oob = GPMC_NAND_HW_BCH8_ECC_LAYOUT;
+
+static struct nand_bch_priv bch_priv = {
+ .mode = NAND_ECC_HW_BCH,
+ .type = ECC_BCH8,
+ .nibbles = ECC_BCH8_NIBBLES
+};
+
+/*
+ * omap_read_bch8_result - Read BCH result for BCH8 level
+ *
+ * @mtd: MTD device structure
+ * @big_endian: When set read register 3 first
+ * @ecc_code: Read syndrome from BCH result registers
+ */
+static void omap_read_bch8_result(struct mtd_info *mtd, uint8_t big_endian,
+ uint8_t *ecc_code)
+{
+ uint32_t *ptr;
+ int8_t i = 0, j;
+
+ if (big_endian) {
+ ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[3];
+ ecc_code[i++] = readl(ptr) & 0xFF;
+ ptr--;
+ for (j = 0; j < 3; j++) {
+ ecc_code[i++] = (readl(ptr) >> 24) & 0xFF;
+ ecc_code[i++] = (readl(ptr) >> 16) & 0xFF;
+ ecc_code[i++] = (readl(ptr) >> 8) & 0xFF;
+ ecc_code[i++] = readl(ptr) & 0xFF;
+ ptr--;
+ }
+ } else {
+ ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[0];
+ for (j = 0; j < 3; j++) {
+ ecc_code[i++] = readl(ptr) & 0xFF;
+ ecc_code[i++] = (readl(ptr) >> 8) & 0xFF;
+ ecc_code[i++] = (readl(ptr) >> 16) & 0xFF;
+ ecc_code[i++] = (readl(ptr) >> 24) & 0xFF;
+ ptr++;
+ }
+ ecc_code[i++] = readl(ptr) & 0xFF;
+ ecc_code[i++] = 0; /* 14th byte is always zero */
+ }
+}
+
+/*
+ * omap_ecc_disable - Disable H/W ECC calculation
+ *
+ * @mtd: MTD device structure
+ *
+ */
+static void omap_ecc_disable(struct mtd_info *mtd)
+{
+ writel((readl(&gpmc_cfg->ecc_config) & ~0x1),
+ &gpmc_cfg->ecc_config);
+}
+
+/*
+ * omap_rotate_ecc_bch - Rotate the syndrome bytes
+ *
+ * @mtd: MTD device structure
+ * @calc_ecc: ECC read from ECC registers
+ * @syndrome: Rotated syndrome will be retuned in this array
+ *
+ */
+static void omap_rotate_ecc_bch(struct mtd_info *mtd, uint8_t *calc_ecc,
+ uint8_t *syndrome)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nand_bch_priv *bch = chip->priv;
+ uint8_t n_bytes = 0;
+ int8_t i, j;
+
+ switch (bch->type) {
+ case ECC_BCH4:
+ n_bytes = 8;
+ break;
+
+ case ECC_BCH16:
+ n_bytes = 28;
+ break;
+
+ case ECC_BCH8:
+ default:
+ n_bytes = 13;
+ break;
+ }
+
+ for (i = 0, j = (n_bytes-1); i < n_bytes; i++, j--)
+ syndrome[i] = calc_ecc[j];
+}
+
+/*
+ * omap_calculate_ecc_bch - Read BCH ECC result
+ *
+ * @mtd: MTD structure
+ * @dat: unused
+ * @ecc_code: ecc_code buffer
+ */
+static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat,
+ uint8_t *ecc_code)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nand_bch_priv *bch = chip->priv;
+ uint8_t big_endian = 1;
+ int8_t ret = 0;
+
+ if (bch->type == ECC_BCH8)
+ omap_read_bch8_result(mtd, big_endian, ecc_code);
+ else /* BCH4 and BCH16 currently not supported */
+ ret = -1;
+
+ /*
+ * Stop reading anymore ECC vals and clear old results
+ * enable will be called if more reads are required
+ */
+ omap_ecc_disable(mtd);
+
+ return ret;
+}
+
+/*
+ * omap_fix_errors_bch - Correct bch error in the data
+ *
+ * @mtd: MTD device structure
+ * @data: Data read from flash
+ * @error_count:Number of errors in data
+ * @error_loc: Locations of errors in the data
+ *
+ */
+static void omap_fix_errors_bch(struct mtd_info *mtd, uint8_t *data,
+ uint32_t error_count, uint32_t *error_loc)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nand_bch_priv *bch = chip->priv;
+ uint8_t count = 0;
+ uint32_t error_byte_pos;
+ uint32_t error_bit_mask;
+ uint32_t last_bit = (bch->nibbles * 4) - 1;
+
+ /* Flip all bits as specified by the error location array. */
+ /* FOR( each found error location flip the bit ) */
+ for (count = 0; count < error_count; count++) {
+ if (error_loc[count] > last_bit) {
+ /* Remove the ECC spare bits from correction. */
+ error_loc[count] -= (last_bit + 1);
+ /* Offset bit in data region */
+ error_byte_pos = ((512 * 8) -
+ (error_loc[count]) - 1) / 8;
+ /* Error Bit mask */
+ error_bit_mask = 0x1 << (error_loc[count] % 8);
+ /* Toggle the error bit to make the correction. */
+ data[error_byte_pos] ^= error_bit_mask;
+ }
+ }
+}
+
+/*
+ * omap_correct_data_bch - Compares the ecc read from nand spare area
+ * with ECC registers values and corrects one bit error if it has occured
+ *
+ * @mtd: MTD device structure
+ * @dat: page data
+ * @read_ecc: ecc read from nand flash (ignored)
+ * @calc_ecc: ecc read from ECC registers
+ *
+ * @return 0 if data is OK or corrected, else returns -1
+ */
+static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat,
+ uint8_t *read_ecc, uint8_t *calc_ecc)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nand_bch_priv *bch = chip->priv;
+ uint8_t syndrome[28];
+ uint32_t error_count = 0;
+ uint32_t error_loc[8];
+ uint32_t i, ecc_flag;
+
+ ecc_flag = 0;
+ for (i = 0; i < chip->ecc.bytes; i++)
+ if (read_ecc[i] != 0xff)
+ ecc_flag = 1;
+
+ if (!ecc_flag)
+ return 0;
+
+ elm_reset();
+ elm_config((enum bch_level)(bch->type));
+
+ /*
+ * while reading ECC result we read it in big endian.
+ * Hence while loading to ELM we have rotate to get the right endian.
+ */
+ omap_rotate_ecc_bch(mtd, calc_ecc, syndrome);
+
+ /* use elm module to check for errors */
+ if (elm_check_error(syndrome, bch->nibbles, &error_count,
+ error_loc) != 0) {
+ printf("ECC: uncorrectable.\n");
+ return -1;
+ }
+
+ /* correct bch error */
+ if (error_count > 0)
+ omap_fix_errors_bch(mtd, dat, error_count, error_loc);
+
+ return 0;
+}
+/*
+ * omap_hwecc_init_bch - Initialize the BCH Hardware ECC for NAND flash in
+ * GPMC controller
+ * @mtd: MTD device structure
+ * @mode: Read/Write mode
+ */
+static void omap_hwecc_init_bch(struct nand_chip *chip, int32_t mode)
+{
+ uint32_t val, dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1;
+ uint32_t unused_length = 0;
+ struct nand_bch_priv *bch = chip->priv;
+
+ switch (bch->nibbles) {
+ case ECC_BCH4_NIBBLES:
+ unused_length = 3;
+ break;
+ case ECC_BCH8_NIBBLES:
+ unused_length = 2;
+ break;
+ case ECC_BCH16_NIBBLES:
+ unused_length = 0;
+ break;
+ }
+
+ /* Clear the ecc result registers, select ecc reg as 1 */
+ writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control);
+
+ switch (mode) {
+ case NAND_ECC_WRITE:
+ /* eccsize1 config */
+ val = ((unused_length + bch->nibbles) << 22);
+ break;
+
+ case NAND_ECC_READ:
+ default:
+ /* by default eccsize0 selected for ecc1resultsize */
+ /* eccsize0 config */
+ val = (bch->nibbles << 12);
+ /* eccsize1 config */
+ val |= (unused_length << 22);
+ break;
+ }
+ /* ecc size configuration */
+ writel(val, &gpmc_cfg->ecc_size_config);
+ /* by default 512bytes sector page is selected */
+ /* set bch mode */
+ val = (1 << 16);
+ /* bch4 / bch8 / bch16 */
+ val |= (bch->type << 12);
+ /* set wrap mode to 1 */
+ val |= (1 << 8);
+ val |= (dev_width << 7);
+ val |= (cs << 1);
+ writel(val, &gpmc_cfg->ecc_config);
+}
+
+/*
+ * omap_enable_ecc_bch- This function enables the bch h/w ecc functionality
+ * @mtd: MTD device structure
+ * @mode: Read/Write mode
+ *
+ */
+static void omap_enable_ecc_bch(struct mtd_info *mtd, int32_t mode)
+{
+ struct nand_chip *chip = mtd->priv;
+
+ omap_hwecc_init_bch(chip, mode);
+ /* enable ecc */
+ writel((readl(&gpmc_cfg->ecc_config) | 0x1), &gpmc_cfg->ecc_config);
+}
+
+/**
+ * omap_read_page_bch - hardware ecc based page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @page: page number to read
+ *
+ */
+static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int page)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *p = buf;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ uint8_t *ecc_code = chip->buffers->ecccode;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ uint8_t *oob = chip->oob_poi;
+ uint32_t data_pos;
+ uint32_t oob_pos;
+
+ data_pos = 0;
+ /* oob area start */
+ oob_pos = (eccsize * eccsteps) + chip->ecc.layout->eccpos[0];
+ oob += chip->ecc.layout->eccpos[0];
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize,
+ oob += eccbytes) {
+ chip->ecc.hwctl(mtd, NAND_ECC_READ);
+ /* read data */
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_pos, page);
+ chip->read_buf(mtd, p, eccsize);
+
+ /* read respective ecc from oob area */
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_pos, page);
+ chip->read_buf(mtd, oob, eccbytes);
+ /* read syndrome */
+ chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+
+ data_pos += eccsize;
+ oob_pos += eccbytes;
+ }
+
+ for (i = 0; i < chip->ecc.total; i++)
+ ecc_code[i] = chip->oob_poi[eccpos[i]];
+
+ eccsteps = chip->ecc.steps;
+ p = buf;
+
+ for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ int stat;
+
+ stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
+ if (stat < 0)
+ mtd->ecc_stats.failed++;
+ else
+ mtd->ecc_stats.corrected += stat;
+ }
+ return 0;
+}
+#endif /* CONFIG_AM33XX */
+
#ifndef CONFIG_SPL_BUILD
/*
* omap_nand_switch_ecc - switch the ECC operation b/w h/w ecc and s/w ecc.
nand->ecc.calculate = NULL;
/* Setup the ecc configurations again */
- if (hardware) {
+ if (hardware == 1) {
nand->ecc.mode = NAND_ECC_HW;
nand->ecc.layout = &hw_nand_oob;
nand->ecc.size = 512;
nand->ecc.calculate = omap_calculate_ecc;
omap_hwecc_init(nand);
printf("HW ECC selected\n");
+#ifdef CONFIG_AM33XX
+ } else if (hardware == 2) {
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.layout = &hw_bch8_nand_oob;
+ nand->ecc.size = 512;
+ nand->ecc.bytes = 14;
+ nand->ecc.read_page = omap_read_page_bch;
+ nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.correct = omap_correct_data_bch;
+ nand->ecc.calculate = omap_calculate_ecc_bch;
+ omap_hwecc_init_bch(nand, NAND_ECC_READ);
+ printf("HW BCH8 selected\n");
+#endif
} else {
nand->ecc.mode = NAND_ECC_SOFT;
/* Use mtd default settings */
nand->options |= NAND_BUSWIDTH_16;
nand->chip_delay = 100;
+
+#ifdef CONFIG_AM33XX
+ /* required in case of BCH */
+ elm_init();
+
+ /* BCH info that will be correct for SPL or overridden otherwise. */
+ nand->priv = &bch_priv;
+#endif
+
/* Default ECC mode */
+#ifdef CONFIG_AM33XX
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.layout = &hw_bch8_nand_oob;
+ nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE;
+ nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES;
+ nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.correct = omap_correct_data_bch;
+ nand->ecc.calculate = omap_calculate_ecc_bch;
+ nand->ecc.read_page = omap_read_page_bch;
+ omap_hwecc_init_bch(nand, NAND_ECC_READ);
+#else
#if !defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_NAND_SOFTECC)
nand->ecc.mode = NAND_ECC_SOFT;
#else
nand->ecc.calculate = omap_calculate_ecc;
omap_hwecc_init(nand);
#endif
+#endif
#ifdef CONFIG_SPL_BUILD
if (nand->options & NAND_BUSWIDTH_16)
projects / u-boot.git / commitdiff